Bis(acetylacetonato) dioxomolybdenum(VI) catalysed rearrangement of methylbutynol in the presence of ultrasound

The molybdenum (VI) catalysed rearrangement of methylbutynol was carried out under the influence of ultrasound (20 kHz). Surprisingly, 2-methylpropene (isobutene) was found as the main product. The formation of isobutene can be explained by rearrangement to prenal, oxidation to 3,3-dimethylacrylic acid and then decarboxylation. 3,3-Dimethylacrylic acid was decarboxylated in the presence of ultrasound and a catalyst; without a catalyst or without ultrasound (at 50 degrees C) it remained unchanged.     

Ultrasonic effects on titanium tanning of leather

The effects of ultrasound on titanium tanning of leather were investigated. Either 20 or 40 kHz ultrasound was applied to the titanium tanning of pigskins. Five different treatment conditions were carried out and the effects were examined, such as leather shrinkage temperature (T(s)), titanium content and titanium distribution in the leather. Overall heat loading was carefully controlled. Results showed that 20 kHz ultrasound effectively improves titanium agent penetration into the hide and increases the leather's shrinkage temperature. Doubling the frequency to 40 kHz produced negligible enhancements. An impressive 105.6 degrees C T(s) was achieved using 20 kHz ultrasound pretreatment of the tanning liquor followed by 20 kHz ultrasound in the tanning mixture (liquor plus pigskins) in a special salt-free medium. Finally, using a unique ultrasonic tanning drum with 26.5 kHz ultrasound, the T(s) reached a record level of 106.5 degrees C, a value not achieved in conventional (no ultrasound) titanium tanning. The ultrasonic effects on titanium tanning of leather are judged to make a superior mineral tanned leather.     

Iron removal from kaolin using thiourea assisted by ultrasonic wave

In the present study a bleaching process of a kaolinite was carried out using thiourea as the leachant agent in the iron removal process, in the absence and presence of ultrasound. The effect of thiourea was investigated together with other factors, such as thiourea concentration, temperature, treatment time, and ultrasonic parameters. The optimum conditions for the maximum whiteness of 89% with ultrasound were determined as follows: reaction temperature, 20 °C; ultrasound frequency, 80 kHz; ultrasound power, 500 W; thiourea concentration, 0.4 wt.%; pH, 3.0; reaction time, 20 min. The assistance of ultrasound led to a remarkable acceleration for the iron leaching process, and dramatic reduction in the concentration of leach reagent, irradiation time, and reaction temperature, when compared with the conventional bleaching method using thiourea in the absence of ultrasound.     

Phase-transfer catalysis and ultrasonic waves II: saponification of vegetable oil.

Saponification of oils which is a commercially important heterogeneous reaction, can be speeded up by the application of ultrasound in the presence of phase-transfer catalyst (PTC). This paper focuses on the ability of ultrasound to cause efficient mixing of this liquid-liquid heterogeneous reaction. Castor oil was taken as a model oil and the kinetic of the reaction was followed by the extent of saponification. The hydrolysis of castor oil was carried out with different PTC such as cetyl trimethyl ammonium bromide (CTAB), benzyl triethyl ammonium chloride (BTAC) and tetrabutyl ammonium bromide (TBAB) in aqueous alkaline solution. As hydroxyl anion moves very slowly from aqueous to oil phase, the presence of a PTC is of prime importance. For this purpose, cationic surfactants are selected. The sonication of biphasic system were performed by 20 kHz (simple horn and cup horn) and 900 kHz. It was found that CTAB was better than the two others and this could be related to the molecular structure of the PTCs. The effect of temperature was also studied on the saponification process. By increasing the temperature, the yield was also increased and this could be explained by intermolecular forces, interfacial tension and mass transfer. Saponification of three different vegetable oils shows that the almond oil is saponified easier than the two others and this could be related to their properties such as surface tension, viscosity and density.     

Ultrasonic-assisted synthesis of chrysin derivatives linked with 1,2,3-triazoles by 1,3-dipolar cycloaddition reaction

The 1,3-dipolar cycloaddition reaction between 7-(3-azidopropoxy)-5-hydroxyflavone and phenylacetylene was carried out to investigate the synthesis of 7-(3-(4-phenyl-1,2,3-triazol-1-yl)propoxy)- 5-hydroxyflavone in presence of ultrasound (sono-synthesis) and absence of ultrasound (conventional method) under relatively optimized solvent and catalyst conditions. The reaction rate was notably accelerated with the help of ultrasound irradiation. An experiment was especially carried out for investigating the acceleration mechanism of ultrasound on the cycloaddition. A novel series of chrysin derivatives linked with 1,2,3-triazoles were obtained by the copper(I)-catalyzed 1,3-dipolar Huisgen cycloaddition reaction using t-BuOH/H(2)O (1:1 v/v) as reaction solvents and CuSO(4)·5H(2)O/sodium ascorbate as the catalyst at room temperature in the presence of ultrasound irradiation. Their structures are elucidated by NMR, ESI MS, IR and Elemental analysis.     

Fast and efficient removal of Reactive Black 5 from aqueous solution by a combined method of ultrasound and sorption process

Removal of Reactive Black 5 (RB5) from aqueous solutions was carried by the sorption process in the presence and in the absence of ultrasound. Sorption of the dye on the solid phase was investigated in a series of batch sorption experiments to determine the influence of different parameters such as contact time, amount of sorbent and concentration of pollutant on the removal efficiency of RB5 with and without ultrasound. The experimental data were fitted properly to the Freundlich model and the isotherm constants were 28.2 and 7.4 for k(f) and 0.13 and 0.38 for 1/n in the presence and in the absence of ultrasound (20 kHz) respectively. The data were analyzed with different sorption kinetic models and were better fitted with a pseudo-second-order kinetic model. Two ultrasonic generators at 20 and 500 kHz were used for sonication of the system. This investigation also reveals that RB5 can be removed by higher frequency apparatus (500 kHz) without sorbent in about 60 min sonication. The rate of removal was higher at the higher frequency than at the lower one.     

Effects of ultrasonic treatment on zeolite NaA synthesized from by-product silica

The synthesis of zeolite NaA from silica by-product was carried out in the presence of 20 kHz ultrasound at room temperature. Zeolites obtained in this type of synthesis were compared to zeolites obtained by performing conventional static syntheses under similar conditions. The sonication effects on zeolite NaA synthesis were characterized by phase identification, crystallinity etc. The effects of different parameters such as crystallization time and initial materials preparation methods on the crystallinity and morphology of the synthesized zeolites were investigated. The final products were characterized by XRD and FT-IR. It was possible to obtain crystalline zeolite NaA from by-product silica in the presence of ultrasound.     

Growth rate of potash alum crystals: comparison of silent and ultrasonic conditions

The influence of power ultrasound on the growth rate of potash alum was investigated. The experiments on growth of potash alum crystals were carried out in a stirred double jacket tank in silent conditions as well as in the presence of power ultrasound (20 kHz) at 32 degrees C, with different initial crystal sizes. It was observed that the mass growth rate of potash alum was faster under ultrasound compared to that under silent conditions. The shape was not modified by ultrasound but the size of crystals, which are grown under ultrasound, are smaller and with higher density compared to those grown under silent conditions.     

Sonoelectrochemical hydrogenation of safrole: A reactor design,statistical analysis and computational fluid dynamic approach

In this work, ultrasound-assisted electrocatalytic hydrogenation (US-ECHSA) of safrole was carried out in water medium, using sacrificial anode of nickel. The ultrasonic irradiation was carried out at frequency of 20 kHz ± 500 Hz with a titanium cylindrical horn (MS 73 microtip; Ti-6AI-4V alloy; 3.0 mm diameter). The optimal conditions were analyzed by statistical experimental design (fractional factorial). The influence of the sonoelectrochemical reactor design was also investigated by using computational fluid dynamics as simulation tool. Among the five parameters studied: catalyst type, use of β-cyclodextrin as inverse phase transfer catalyst, sonoelectrochemical reactor design, ultrasound mode and the temperature of the solution, only the last three were significant. The hydrogenation product, dihydrosafrole, reached 94% yield, depending on the experimental conditions applied. Data of computational fluid dynamics showed that a wing shape tube added to the sonoelectrochemical reactor can work as a cooling apparatus, during the electrochemical process. The reactional solution temperature diminishes 14 °C when compared to the four-way-type reactor. Cooper cathode, absence of β-cyclodextrin, four-way-type reactor, ultrasound continuous mode (14 W) and absence of temperature control were the most effective reaction parameters for the safrole hydrogenation using US-ECHSA method. The proposed approach represents an important contribution for understanding the hydrodynamic behavior of sonoelectrochemical reactors designs and, consequently, for the reducing of the experimental costs inherent to the sonoelectrochemical process.     

Efficient one-pot three-component synthesis of N-(4-arylthiazol-2-yl) hydrazones in water under ultrasound irradiation

A highly efficient and facile one-pot three-component synthesis of N-(4-arylthiazol-2-yl) hydrazones was carried out in excellent yield without any catalyst in water under ultrasound irradiation.     

Preparation of 1,3-bis(allyloxy)benzene under a new multi-site phase-transfer catalyst combined with ultrasonication – A kinetic study

In the present work, kinetics of synthesis of 1,3-bis(allyloxy)benzene was successfully carried out by O-allylation of resorcinol with allyl bromide using aqueous potassium hydroxide and catalyzed by a new multi-site phase-transfer catalyst viz., 1,3,5,7-tetrabenzylhexamethylenetetraammonium tetrachloride, MPTC under ultrasonic (40 kHz, 300 W) assisted organic solvent condition. The pseudo first-order kinetic equation was applied to describe the overall reaction. Under ultrasound irradiation (40 kHz, 300 W) in a batch reactor, it shows that the overall reaction rate can be greatly enhanced to seven fold faster with ultrasound irradiation than without ultrasound. The present study provides a method to synthesize ethers by ultrasound assisted liquid–liquid phase-transfer catalysis condition.     

Ultrasound assisted intensification of biodiesel production using enzymatic interesterification

Ultrasound assisted intensification of synthesis of biodiesel from waste cooking oil using methyl acetate and immobilized lipase obtained from Thermomyces lanuginosus (Lipozyme TLIM) as a catalyst has been investigated in the present work. The reaction has also been investigated using the conventional approach based on stirring so as to establish the beneficial effects obtained due to the use of ultrasound. Effect of operating conditions such as reactant molar ratio (oil and methyl acetate), temperature and enzyme loading on the yield of biodiesel has been investigated. Optimum conditions for the conventional approach (without ultrasound) were established as reactant molar ratio of 1:12 (oil:methyl acetate), enzyme loading of 6% (w/v), temperature of 40 °C and reaction time of 24 h and under these conditions, 90.1% biodiesel yield was obtained. The optimum conditions for the ultrasound assisted approach were oil to methyl acetate molar ratio of 1:9, enzyme loading of 3% (w/v), and reaction time of 3 h and the biodiesel yield obtained under these conditions was 96.1%. Use of ultrasound resulted in significant reduction in the reaction time with higher yields and lower requirement of the enzyme loading. The obtained results have clearly established that ultrasound assisted interesterification was a fast and efficient approach for biodiesel production giving significant benefits, which can help in reducing the costs of production. Reusability studies for the enzyme were also performed but it was observed that reuse of the catalyst under the optimum experimental condition resulted in reduced enzyme activity and biodiesel yield.     

Influence of particles on sonochemical reactions in aqueous solutions

Numerous publications deal with the possible application of ultrasound for elimination of organic pollutants as a tool for water pollution abatement. Most of the experiments were performed in pure water under laboratory conditions. For developing technologies that hold promise it is necessary to investigate the effect of ultrasound in natural systems or waste water where particulate matter could play an important role. In this paper the influence of quartz particles (2-25 microm) on the chemical effects of ultrasound in aqueous system using a high power ultrasound generator (68-1028 kHz, 100 W, reactor volume 500 ml) is reported. In pure water in dependence on particle size, concentration and frequency the formation rate of hydrogen peroxide under Ar/O2 (4:1) shows a maximum using 206 kHz in presence of 3-5 microm quartz particles (4-8 g/l). Under these conditions the yield of peroxide is higher than without quartz. Additionally under N2/O2 (4:1) besides hydrogen peroxide the formation of nitrite/nitrate was measured. Compared to pure water quartz particle depressed the formation of nitrite/nitrate up to 10-fold but not the formation of H2O2. According to the results of H2O2 formation the elimination of organic compounds by sonolysis (206 kHz) and the influence of quartz particles were investigated. As organic compounds salicylic acid, 2-chlorobenzoic acid and p-toluenesulfonic acid were used. The influence of quartz on the oxidation of organic compounds (206 kHz) is similar to that on the formation of H2O2.     

Sono-catalytic degradation and fast mineralization of p-chlorophenol: La0.7Sr0.3MnO3 as a nano-magnetic green catalyst

La_0.7Sr_0.3MnO₃ (LSMO) nanoparticles with a perovskite structure were prepared by a combination of ultrasound and co-precipitation method. The synthesized catalyst was characterized by X-ray diffraction, transmission electron microscopy, Fourier transform infrared spectroscopy. The catalytic performance of the catalyst was evaluated for the degradation of 4-chlorophenol in the presence and in the absence of ultrasound. The degradation has been studied at different temperatures, pH, catalyst dosage, and initial concentration of 4-chlorophenol. The results have shown that the degradation efficiency was higher in the presence of ultrasound than its absence under the mild conditions. More than 88% decrease in the concentration and 85% decrease in the TOC for 4-chlorophenol could be achieved in a short time of sonication with respect to the conventional method. This behavior could be attributed to the cavitation process which followed by a high mass transfer on the catalyst with high surface area. These conditions led to facilitate the removal of pollutant from aqueous solution. The results also indicated that the catalyst without recalcination can be used successfully up to five consecutive cycles without any significant loss in activity in the presence and in the absence of ultrasound. In addition, the most important is the magnetic property of the nanoparticles which separated easily from aqueous solution by an external magnetic field.     

Ultrasound-assisted dextranase entrapment onto Ca-alginate gel beads

In this research work, dextranase has immobilized onto calcium alginate beads using a novel ultrasound method. The process of immobilization of the enzyme was carried out in a one-step ultrasound process. Effects of ultrasound conditions on loading efficiency and immobilization yield of the enzyme onto calcium alginate beads were investigated. Furthermore, the activity of the free and immobilized enzymes prepared with and without ultrasound treatment, as a function of pH, temperature, recyclability and enzyme kinetic parameters, was compared. The maximum loading efficiency and the immobilization yield were observed when the immobilized dextranase was prepared with an ultrasonic irradiation at 25 kHz, 40 W for 15 min, under which the loading efficiency and the immobilization yield increased by 27.21% and 18.77%, respectively, compared with the immobilized enzymes prepared without ultrasonic irradiation. On the other hand, immobilized enzyme prepared with ultrasonic irradiation showed V_max and K_M value higher than that for the immobilized enzyme prepared without ultrasonic irradiation, likewise, both the catalytic and specificity constants of immobilized enzyme prepared with ultrasonic irradiation were higher than that for immobilized enzyme prepared without ultrasound, indicating that, this new ultrasonic method improved the catalytic kinetics activity of immobilized dextranase at all the reaction conditions studied. Compared with immobilized enzyme prepared without ultrasound treatment, the immobilized enzymes prepared with ultrasound irradiation exhibited: a higher pH optimum, optimal reaction temperature, activation energy, and thermal stability, as well as, a higher recyclability, which, illustrating the effectiveness of the sonochemical method. To the best of our knowledge, this is the first report on the effect of ultrasound treatments on the immobilization of dextranase.     

Ultrasound accelerated esterification of palmitic acid with vitamin C

The esterification of palmitic acid with vitamin C in the presence of concentrated sulfuric acid as the solvent and catalyst by means of 25 kHz ultrasonic irradiation to obtain l-ascorbyl 6-palmitate is studied. By using ultrasound the dissolution rate of the reactants can be accelerated greatly, the reaction time of esterification can be reduced from 36 to 2h, and better yield (90-93%) of ester can be given by using 95% concentrated sulfuric acid as the solvent and catalyst, contrast to the yield of 75-85% by using 99% concentrated sulfuric acid without ultrasound. The influence of reaction conditions and ultrasonic parameters to the yield of ascorbyl palmitate are reported.     

Homogeneous and heterogeneous asymmetric reactions: Part 11. Sonochemical enantioselective hydrogenation of trifluoromethyl ketones over platinum catalysts

Enantioselective sonochemical hydrogenation of alpha,alpha,alpha-trifluoromethyl ketones, namely, 1,1,1-trifluoroacetophenone and 1,1,1-trifluoro-phenylacetone was carried out over various platinum catalysts modified by cinchonidine in different solvents. Both compounds yielded the (R)-alcohol as major product. The reaction rates and the enantiomeric excesses were determined over Pt/C, Pt/SiO2, Pt/K-10 and Pt/Al2O3 catalysts under conventional conditions. Since Pt/Al2O3 exhibited the best catalytic performance the effect of ultrasound on the catalytic activity and enantioselectivity was tested using this catalyst applying different sonochemical pretreatments. These methods included a pretreatment before the reaction in hydrogen and oxygen or both. The ultrasonic irradiation was found to be highly advantageous in the case of trifluoroacetophenone, whereas only moderate changes were observed using trifluoro-phenylacetone. After insonation of the catalyst, the enantioselectivity was considerably improved. Both the aerobic and anaerobic sonochemical pretreatments resulted in significant improvement in optical yield (up to 49% and 17% ee, at room temperature under 10 bar in 1,2-dichlorobenzene). In parallel, the hydrogenation rates increased to a small extent (1.1-1.2-fold increase) after hydrogenative ultrasonic pretreatment, whereas the rates decreased by a factor of 1.5-2 after aerobic insonation. To obtain more insight into the process, the effect of insonation time on the activity and enantioselectivity and actual changes of the catalyst were also studied.     

Effects of ultrasound on adsorption-desorption of p-chlorophenol on granular activated carbon

The aim of this work is the evaluation of the effects of ultrasound on p-chlorophenol adsorption-desorption on granular activated carbon. Adsorption equilibrium experiments and batch kinetics studies were carried out in the presence and the absence of ultrasound at 21 kHz. Results indicate that the adsorption of p-chlorophenol determined in the presence of ultrasound is lower than the adsorption observed in the absence of ultrasound. Desorption of p-chlorophenol from activated carbon with and without the application of ultrasound was studied. The desorption rates were favoured by increased ultrasound intensity. This rise is more noticeable as temperature increases. The addition of ethanol or NaOH to the system causes an enhancement of the amount of p-chlorophenol desorbed, especially in the presence of ultrasound. A synergetic enhancement of the desorption rate was observed when ultrasonic irradiation was coupled with ethanol chemical regeneration.     

Ultrasound-Engineered fabrication of immobilized molybdenum complex on Cross-Linked poly (Ionic Liquid) as a new acidic catalyst for the regioselective synthesis of pharmaceutical polysubstituted spiro compounds

A novel supported molybdenum complex on cross-linked poly (1-Aminopropyl-3-vinylimidazolium bromide) entrapped cobalt oxide nanoparticles has been successfully fabricated through two different procedures, i.e. ultrasound (US) irradiations (100 W, 40 kHz) and reflux. The efficiency of the two different methods was comparatively investigated on the fundamental properties of proposed catalyst using diverse characterization techniques. Based on the obtained results, the ultrasonication method provides controlled polymerization process; as a result, well connected polymeric network is formed. In addition, the use of ultrasound waves turned out to be able to increase the particles uniformity, specific surface area (from 79.19 to 223.83 m²/g), and the onset thermal degradation temperature (T_d) value (from 248 to 400 °C) of the prepared catalyst which intensifies the catalytic efficiency. Besides, US-treated catalyst demonstrated high chemical stability and maintained its cross-linked network after eight cycles recovery, while the cross-linked network of catalyst obtained under silent condition was completely disrupted. Furthermore, the ultrafast multi-step fabrication procedure was performed in less than 6 h under ultrasonic condition while a similar process promoted by a mechanical stirring method came to a conclusion after 5–6 days. Accordingly, the utility of the ultrasound irradiation was proved, and US-treated catalyst was applied for improved synthetic methodology of spiro 1,4-dihydropyridines and spiro pyranopyrazoles through different acidic active sites. Due to the significant synergistic influence between the proposed catalyst and US irradiation, a variety of novel and recognized mono-spiro compounds were fabricated at room temperature in high regioselectivity.     

Studies on the use of power ultrasound in leather dyeing

Uses of power ultrasound for acceleration/performing the chemical as well as physical processes are gaining importance. In conventional leather processing, the diffusion of chemicals through the pores of the skin/hide is achieved by the mechanical agitation caused by the paddle or drumming action. In this work, the use of power ultrasound in the dyeing of leather has been studied with the aim to improve the exhaustion of dye for a given processing time, to reduce the dyeing time and to improve the quality of dyed leather. The effect of power ultrasound in the dyeing of full chrome cow crust leather in a stationary condition is compared with dyeing in the absence of ultrasound as a control experiment both in a stationary as well as conventional drumming condition. An ultrasonic cleaner (150 W and 33 kHz) was used for the experiments. Actual power dissipated into the system was calculated from the calorimetric measurement. Experiments were carried out with variation in type of dye, amount of dye offer, temperature and time. The results show that there is a significant improvement in the percentage exhaustion of dye due to the presence of ultrasound, when compared to dyeing in absence of ultrasound. Experiments on equilibrium dye uptake carried out with or without ultrasound suggest that ultrasound help to improve the kinetics of leather dyeing. The results indicate that leathers dyed in presence of ultrasound have higher colour values, better dye penetration and fastness properties compared to control leathers. The physical testing results show that strength properties of the dyed leathers are not affected due to the application of ultrasound under the given process conditions. Apparent diffusion coefficient during the initial stage of dyeing process, both in presence and in absence of ultrasound was calculated. The values show that ultrasound helps in improving the apparent diffusion coefficient more for the difficult dyeing conditions such as in the case of metal-complex dyes having bigger aggregate size compared to less difficult dyeing conditions.