Voltammetric study of the interaction of lomefloxacin (LMF)–Mg(II) complex with DNA and its analytical application

The voltammetric behavior of the LMF-Mg(II) complex with DNA at a mercury electrode is reported for the first time. In NH₃–NH₄Cl buffer (pH=9.10), the adsorption phenomena of the LMF–Mg(II) complex were observed by linear sweep voltammetry. The mechanism of the electrode reaction was found to be a reduction of LMF in the complex, and the composition of the LMF–Mg(II) complex is 2:1. In the presence of calf thymus DNA (ctDNA), the peak current of LMF–Mg(II) complex decreased considerably, and a new well-defined adsorptive reduction peak appeared at −1.63 V (vs. SCE). The electrochemical kinetic parameters and the binding number of LMF–Mg(II) with ctDNA were also obtained. Moreover, the new peak currents of LMF–Mg(II)–DNA system increased linearly correlated to the concentration of DNA in the 4.00×10⁻⁷–2.60×10⁻⁶ g ml⁻¹ range when the concentrations of LMF–Mg(II) complex was fixed at 5.00×10⁻⁶ mol l⁻¹, with the detection limits of 2.33×10⁻⁷ g ml⁻¹. An electrostatic interaction was suggested by electrochemical method.     

Voltammetric determination of quercetin at a multi-walled carbon nanotubes paste electrode

Quercetin can effectively accumulate at multi-walled carbon nanotubes-paraffin oil paste electrodes (CNTPE) and cause a sensitive anodic peak at around 0.32 V (vs. SCE) in a 0.10 M phosphate buffer solution (pH = 4.0). Under optimized conditions, the anodic peak current is linear to quercetin concentration in the ranges of 2.0 × 10^− 9−1.0 × 10^− 7 M and 1.0 × 10^− 7−2.0 × 10^− 5 M, and the regression equations are i_p (μA) = 0.0017 + 0.928c (μM, r = 0.999) and i_p (μA) = 0.183 + 0.0731c (μM, r = 0.995), respectively. This paste electrode can be regenerated by repetitively cycling in a blank solution for about 2 min. A 1.0 × 10^− 6 M quercetin solution is measured for 10 times using the same electrode regenerated after every determination, and the relative standard deviation of the peak current is 1.7%. The method has been applied to the determination of quercetin in hydrolysate product of rutin and the recovery is 99.2–102.6%. In comparison with graphite paste electrode, carbon nanotubes-nujol paste electrode and carbon nanotubes casting film modified glassy carbon electrode, the CNTPE gives higher ratio of signal to background current and better defined voltammetric peak.     

Electrocatalytic response of carbohydrates at copper-alloy electrodes

The voltammetric responses observed for carbohydrates and polyalcohols at 0.60 V in 0.10 M NaOH are significantly larger at preanodized CuMn (95:5) electrodes as compared to preanodized pure Cu electrodes. Apparent values for the number of electrons transferred (n_app) and the corresponding values of heterogeneous rate constants (k_app) are estimated for selected reactants from the slopes and intercepts, respectively, of Koutecký–Levich plots of background-corrected voltammetric currents obtained at CuMn and Cu rotated disk electrodes (RDEs). Values of n_app (and k_app) for sorbitol and glucose are 11.8 (9.2×10⁻³ cm s⁻¹) and 11.7 (8.0×10⁻³ cm s⁻¹), respectively, at a CuMn RDE. These are compared to the values 10.4 (1.8×10⁻³ cm s⁻¹) and 9.6 (2.0×10⁻³ cm s⁻¹) for sorbitol and glucose, respectively, at a Cu RDE. The larger sensitivities observed at the CuMn RDE in comparison to the Cu RDE are concluded to be the beneficial result of larger k_app values at the alloy electrode. Furthermore, the larger k_app values are speculated to result from enhanced preadsorption of the reactant species at Mn(IV) sites in the preanodized CuMn surface. In flow-injection measurements, the peak signals obtained for successive injections of glucose using a CuMn electrode (0.60 V vs. SCE) were quite stable with a standard deviation of 1.5%. However, large day-to-day variations (±15%) observed in the average peak signals are attributed to the temperature sensitivities of the k_app value and the diffusion coefficient for glucose.     

Electrochemical Behavior and Determination of Uric Acid at Single-Walled Carbon Nanotube Modified Gold Electrodes

The voltammetric behavior of uric acid was studied at a single-walled carbon nanotube (SWNT) modified gold electrode. Uric acid can effectively accumulate at this electrode and produce an anodic peak at about 0.45 V (vs. SCE) in pH 5.0 sodium acetate buffer solutions (HAc-NaAc). The experimental parameters, such as solution pH, accumulation time, and amount of SWNT, were optimized for determination. Under the optimum conditions, the anodic peak current is linear to the uric acid concentration over the range of 1.0×10⁻⁷ M to 2.5×10⁻⁵ M with a correlation coefficient of 0.998. The detection limit was 5.0×10⁻⁸ M for 60 s accumulation. The electrode could be easily regenerated and exhibited good stability. A 5.0×10⁻⁶ M uric acid solution was measured ten times using the same electrode, and the relative standard deviation of the peak current was 1.3%. This method was successfully applied to the determination of uric acid in human urine samples, and the recovery was 97–99%. The feasibility for simultaneous determination of xanthine, ascorbic acid and uric acid was discussed. These species did not interfere with each other in a certain concentration range. The influence of some surfactants on the anodic peak was also examined.     

Application of Voltammetric Method of Total Chromium Determination in the Presence of Cupferron for Selective Determination of Cr(VI) in Water Samples

A voltammetric method of Cr(VI) determination in a flow system based on the combination of selective accumulation of the product of Cr(VI) reduction on hanging mercury drop electrode and a very sensitive method of chromium determination in the presence of cupferron previously described is proposed. The calibration graphs were linear from 3 × 10⁻⁹ to 3 × 10⁻⁸ and from 5 × 10⁻¹⁰ to 5 × 10⁻⁹ mol L⁻¹ for accumulation times of 120 and 600 s, respectively. The detection limit for the accumulation time of 600 s was 9 × 10⁻¹¹ mol L⁻¹. The relative standard deviation was 5.1% (n = 5) for Cr(VI) concentration 1 × 10⁻⁸ mol L⁻¹ and the accumulation time of 120 s. The influence of foreign ions commonly present in water samples is presented. The validation of the method was made by studying the recovery of Cr(VI) from spiked natural water samples.     

Modified glassy carbon electrode by electropolymerization of tetrakis-(2-aminopheny)porphyrin for the determination of norepinephrine in the presence of ascorbic acid

A glassy carbon electrode (GCE) was modified with electropolymerization of meso-tetrakis(2-aminophenyl)porphyrin (TAPP) in acetonitrile by cyclic voltammetry (CV). The voltammetric behavior of norepinephrine (NE) in the presence of excess ascorbic acid (AA) was investigated at the modified electrode by cyclic and square wave voltammetry (SWV) in phosphate buffer solution. The modified electrode gave higher selectivity and highly effective electroactivity to NE oxidation in voltammetric measurements of NE in the presence of AA and epinephrine. In pH 7.4 phosphate buffer solution, the peak current increased linearly with the concentration of NE in two concentration ranges of 1.0×10⁻⁶ to 5.0×10⁻⁵ mol dm⁻³.     

Electroanalysis of myoglobin and hemoglobin with a boron-doped diamond electrode

The electrochemical behavior of myoglobin (Mb) and hemoglobin (Hb) was investigated with a boron-doped diamond (BDD) electrode by cyclic voltammetry. In acetate buffer solutions, the oxygen reduction at the BDD electrode showed a very high overpotential while the reduction of Mb or Hb was observed in the more positive potential region. Owing to the electrocatalytic reaction of O₂ and the participation of H⁺ following the electrochemical reduction of ferric proteins, the voltammetric responses for Mb and Hb on the BDD electrode in the negative going scans became remarkable in acidic buffer solutions in air. The peak current was linearly proportional to the concentration of Mb in the range 1×10⁻⁶–2×10⁻⁵ M or the concentration of Hb from 1×10⁻⁶ to 1×10⁻⁵ M.     

Sensitive detection of potassium ion using Prussian blue nanotube sensor

A model K⁺ sensor using Prussian blue nanotubes is fabricated by electrochemical deposition of Prussian blue (PB) within the nanochannels of a porous metal-coated membrane with partially covered pore openings. The PB nanotube sensor exhibits excellent stability giving reproducible peak potentials up to 500 measurement cycles, a very low detection limit of 2.0 × 10⁻⁸ M and extremely wide logarithmic linear ranges between 5.0 × 10⁻⁸–7.0 × 10⁻⁴ M and 7.0 × 10⁻⁴–1.0 M. Negligible interferences by Na⁺, Mg²⁺ and Ca²⁺ are observed and a rapid analysis time of 30 s is readily achieved. The ease of electrodeposition, high stability of PB nanotubes and outstanding analytical performance which surpasses conventional PB voltammetric and potentiometric sensors demonstrates potential sensing applications including ion sensors and biosensors using PB and other metal hexacyanoferrate nanotubes.     

Spectrofluorimetric quantification of bromazepam using a highly selective optical probe based on Eu–bromazepam complex in pharmaceutical and serum samples

A rapid, simple and sensitive spectrofluorimetric method for determination of trace amount of bromazepam is developed. In phosphate buffer of pH 7.4. The bromazepam enhance the luminescence intensity of the Eu³⁺ ion in Eu³⁺–bromazepam complex at λ_ex = 390 nm. The produced luminescence intensity of Eu³⁺–bromazepam complex is in proportion to the concentration of bromazepam. The working range for the determination of bromazepam is 2.3 × 10⁻⁸ to 6.2 × 10⁻⁷ M with detection limit (LoD) and quantitative detection limit (LoQ) of 3 × 10⁻⁹ and 1.2 × 10⁻⁸ M, respectively. While, the working range, detection limit (LoD) and quantitative detection limit (LoQ) in case of the quantum yield calculations are 3.7 × 10⁻⁸ to 3.4 × 10⁻⁷ M with of 3.4 × 10⁻⁹ and 9.2 × 10⁻⁸ M, respectively. The enhancement mechanism of the luminescence intensity in the Eu³⁺–bromazepam system has been also explained.     

Determination of 4-methylbenzilidene camphor in sunscreen by square wave voltammetry in media of cationic surfactant

The voltammetric behavior of 4-methylbenzelidene camphor (MBC) was studied by square wave voltammetry (SWV) using mercury electrode. The experimental condition that provided the highest peak current with the best reduction signal definition of MBC was found in Britton-Robinson buffer and cationic surfactants, cetyltrimethylammoniun bromide (CTABr). A single peak of MBC reduction was observed at − 1.21 V versus Ag/AgCl. The developed methodology was applied for determination of MBC in commercial sunscreen SPF 15, 20 and 30 and for the simultaneous determination when other protection agents were associated, such as benzophenone-3 (BENZO) and octyl methoxycinammate (OMC). Both methodologies had shown good determination values for the analyzed samples. The calculated detection limit was 2.99 × 10^− 9 mol L^− 1 and the quantification limit was 9.98 × 10^− 9 mol L^− 1.     

Electroanalytical and chromatographic determination of pentachlorophenol and related molecules in a contaminated soil: a real case example

Electroanalytical and chromatographic methodologies have been applied for the determination of pentachlorophenol (PCP) and some of its derivatives in real soil samples contaminated by industrial discharge. The analytes were extracted with hexane from soil samples collected at different points of the site and mixed to produce a representative sample. Square wave voltammetry (SWV) experiments were carried out on either a boron-doped diamond (BDD) electrode or a gold ultramicroelectrode (Au-UME) in an analyte composed by the Britton-Robinson (B-R) buffer at pH 5.5 with the direct addition of proper amounts of the extract. The voltammetric responses revealed an irreversible anodic peak at approximately 0.80 V vs. Ag/AgCl with a peak current showing a linear dependence on PCP concentration. This linear relationship yielded a detection limit (DL) of 2×10⁻⁸ mol l⁻¹ (or 5.5 μg l⁻¹) for the BDD electrode and 6.9×10⁻⁸ mol l⁻¹ (18.4 μg l⁻¹) for the Au-UME, while the independently measured HPLC detection limit was 1.1×10⁻⁸ mol l⁻¹ (3.0 μg l⁻¹). The application of electroanalytical and chromatographic methodologies in the analysis of soil extracts revealed, besides the PCP responses, signals for some related molecules such as o-tetrachlorobenzoquinone (o-chloranil), hexachlorobenzene and tetrachlorophenol. Recovering experiments for PCP showed a concentration of 27.5 mg kg⁻¹ for the electroanalytical determinations and 26.8 mg kg⁻¹ for the HPLC analysis, values exceedingly high if considering that the maximum residue limit established for natural waters by the Brazilian Environmental Agency is 10 μg l⁻¹.     

牛血清白蛋白在修饰氯离子金纳米通道中的迁移研究

采用化学镀的方法在聚碳酸酯模板上沉积金,制成金纳米通道膜,并对它进行Cl-修饰得到带负电荷的通道。再采用电化学方法(i-t法)对牛血清白蛋白(BSA)在修饰通道中的迁移进行研究。在pH7.4PBS中,对通道两端施加1.0V电压,溶液中离子迁移通过纳米通道时产生电流响应。当溶液中加入BSA后,电流响应减小,且响应变化量与浓度在1.50×10-10~1.35×10-9mol/L范围内呈线性关系,其线性回归方程为|Δi|(μA)=0.0069 0.125c(×10-9mol/L),相关系数为0.9980,检出限为9.46×10-11mol/L(S/N=3)。     

阳离子表面活性剂对电化学法测试牛奶中氯霉素残留量的影响

为探索用电化学方法检测生物样品中氯霉素残留的高灵敏度技术,本实验研究了阳离子表面活性剂十六烷基三甲基溴化铵(CTMAB)对氯霉素在玻碳电极上伏安行为的影响,实验结果表明,以0.02 mol/L高氯酸为支持电解质,在0.40~-0.60 V的范围内进行伏安扫描时,2×10-5mol/L CTMAB能显著提高氯霉素在-0.41 V处的还原峰电流。利用这种改进的电化学方法检测氯霉素的线性范围为0.0026~8 mg/L,检出限达到0.83μg/L。研究了缓冲液种类及其酸碱度及其它表面离子活性剂等对测试氯霉素的影响。     

毛细管电泳-安培法测定复方磺胺甲噁唑片中的有效成分

采用毛细管电泳-安培法(CE-AD)同时分离测定了磺胺甲噁唑(sulfamethoxazole,SMZ)、磺胺嘧啶(sulfadiazine,SD)和抗菌增效剂甲氧苄胺嘧啶(trimethoprim,TMP)3种常用磺胺类抗菌药物成分,考察了实验参数对分离、检测体系的影响。在优化实验条件下,以300μm碳圆盘电极作为工作电极,检测电位为1050mV(vs.SCE),在Na2B4O7(13mmol/L)-KH2PO4(18mmol/L)(pH5.8)的缓冲溶液中,分离电压18kV,进样6s,3组分在14min内可实现基线分离。上述3组分浓度分别在5×10-4~5×10-2、5×10-4~0.1和5×10-4~5×10-2g/L范围内与其峰电流强度呈线性关系,检出限达5.1×10-5~8.0×10-5g/L(S/N=3)。该方法已成功应用于复方磺胺甲噁唑片中抗菌活性成分的含量测定,结果令人满意。     

Adsorption of 2-amino-5-nitropyridine on the (111) and (210) silver faces

The adsorption isotherms of 2-amino-5-nitropyridine (ANP) on the (111) and (210) silver faces from an aqueous solution of 0.09 M KClO₄ + 0.02 M NaOH were determined at −0.4 V vs. the 1 mol⁻¹ calomel electrode using double-potential-step chronocoulometry. The surface concentration Γ_ANP of ANP was obtained by stepping the applied potential from −0.4 V, where ANP is electroinactive, to −1.2 V, where ANP is electroreduced to 2,5-diaminopyridine. The charge involved in this step, once corrected for the diffusive and capacitive contributions, yields 6FΓ_ANP directly. The maximum surface concentration and standard Gibbs energy of adsorption are equal to 3.6 × 10⁻¹⁰ mol cm⁻² and −35 kJ mol⁻¹ on Ag(111) and 5.2 × 10⁻¹⁰ mol cm⁻² and 42 kJ mol⁻¹ on Ag(210), thus demonstrating the strong effect of surface crystallography on the energetics of ANP adsorption.     

Integrated gold-disk microelectrode modified with iron(II)-phthalocyanine for nitric oxide detection in macrophages

An integrated gold-disk microelectrode (IGME) was fabricated and modified with Fe(II)-phthalocyanine (Fe(II)-PC) for NO detection in biological media. Microanalysis of NO using square wave anodic stripping voltammetry (SWASV) in 0.01 M HClO₄ was optimal at the initial potential of 0.1 V, frequency of 100 Hz, pulse amplitude of 25 mV, and a scan rate of 200 mV/s. When the electrode was modified with Fe(II)-phthalocyanines, the anodic peak current and sensitivity of NO were remarkably increased due to the catalytic oxidation of NO. The calibration curve had good linearity in the range from 3.6×10⁻⁵ to 7.2×10⁻⁷ M, and the detection limit was (5.7±1.2)×10⁻⁷ M. Fe(II)-phthalocyanine modified gold-disk microelectrode coated with Nafion was applied to determination of NO released from macrophage cell.     

A polynuclear mixed-valent ruthenium oxide/cyanoruthenate composite that yields thin coatings on a glassy carbon electrode with high catalytic activity toward methanol oxidation

Polynuclear ruthenium oxide/cyanoruthenate films on carbon substrates were grown by cycling the potential between 0.5 and 1.0 V (vs SCE) for 5–90 min in fresh 2 mM RuCl₃·3 H₂O, 2 mM K₄Ru(CN)₆·3 H₂O, 0.5 M KCl solution at pH 2. During the positive scans, the cationic Ru(III,IV)-oxo polynuclear species interacted with the simultaneously formed anionic CN-bridged Ru dimers to yield sparingly soluble deposits on the electrode surfaces. Different thicknesses, typically corresponding to 2–50×10⁻¹⁰ mol cm⁻², could be obtained by varying the cycling times. The absorption spectra of the coatings obtained at SnO₂-covered glass electrodes were different from those known for RuO₂ films and exhibited two absorption bands at about 400 and 700 nm. IR spectroscopic measurements confirmed the presence of a CN group in the deposit, as well as showing significant aquation of the entire coating. Ru, O, N and K (from KCl) were detected by means of Auger electron spectroscopy. The surface electrochemistry and stability of the film were significantly enhanced in K⁺-containing supporting electrolytes. The system provides a durable catalytic surface which allows the voltammetric oxidation of methanol; in 0.5 M H₂SO₄+0.5 M K₂SO₄ electrolyte the resulting anodic peak is at 1.01 V (vs. SCE). Electrooxidation was not possible at bare carbon electrodes, at least before the onset of the electrolyte decomposition.     

Voltammetric determination of N-acetylcysteine using a carbon paste electrode modified with copper(II) hexacyanoferrate(III)

The preparation and electrochemical characterization of a carbon paste electrode modified with copper(II) hexacyanoferrate(III) (CuHCF) as well as its behavior as electrocatalyst toward the oxidation of N-acetylcysteine were investigated. The electrochemical behavior of the modified electrode and the electrooxidation of N-acetylcysteine were explored using sweep linear voltammetry. The best voltammetric response was observed for a paste composition of 20% (w/w) copper(II) hexacyanoferrate(III) complex, acetate buffer solution at pH of 6.0 as the electrolyte and scan rate of 10 mV s^− 1. A linear voltammetric response for N-acetylcysteine was obtained in the concentration range from 1.2 × 10^− 4 to 8.3 × 10^− 4 mol L^− 1, with a detection limit of 6.3 × 10^− 5 mol L^− 1. The proposed electrode is useful for the quality control and routine analysis of N-acetylcysteine in pharmaceutical formulations.     

Study on the interaction between nucleic acid and Eu3+-oxolinic acid and the determination of nucleic acid using the resonance light scattering technique

At pH 9.75, the resonance light scattering (RLS) intensity of OA–Eu³⁺ system is greatly enhanced by nucleic acid. Based on this phenomenon, a new quantitative method for nucleic acid in aqueous solution has been developed. Under the optimum condition, the enhanced RLS is proportional to the concentration of nucleic acid in the range of 1.0 × 10⁻⁹ to 1.0 × 10⁻⁶ g/ml for herring sperm DNA, 8.0 × 10⁻¹⁰ to 1.0 × 10⁻⁶ g/ml for calf thymus DNA and 1.0 × 10⁻⁹ to 1.0 × 10⁻⁶ g/ml for yeast RNA, and their detection limits are 0.020, 0.011 and 0.010 ng/ml, respectively. Synthetic samples and actual samples were satisfactorily determined. In addition, the interaction mechanism between nucleic acid and OA–Eu³⁺ is also investigated.     

Determination of Captropril using adsorptive cathodic differential pulse stripping voltammetry with the HMDE

A voltammetric method for the determination of 3-mercapto-D-2-methylpropanoyl-L-proline, a hypotensive drug whose pharmaceutical name is Captopril (CPT), in the concentration range from 9.0×10⁻¹⁰M to 3×10⁻⁶M, is described. In this range the peak current increases linearly with drug concentration even when different collection periods are used. A self-cleaning Hanging Mercury Drop Electrode (HMDE) was used and a negative Differential Pulse potential (DP) was applied to the indicator electrode. The stripping peak of CPT splits into two peaks as soon as the concentration is increased over about 10⁻⁵M; in the oxidation DP scan, instead, this splitting is observed at a concentration of 2.0×10⁻⁴M. Some attempts were made to verify the suitability of other techniques such as Alternating Current polarography (AC) and the use of a different electrode, the Wax-Impregnated Graphite Electrode (WIGE).