Stress intensity factor determination error by the method of caustics

The caustics created at a crack tip under biaxial loading are examined using both the closed form and the approximate solution. Particular attention is given to the caustics and their initial curves created by rays reflected from the rear and front surfaces of the specimen in addition to those in the transverse direction of the cracked specimen. These quantities can differ by more than 30% depending on whether the exact or the approximate solution is used for determining the stress intensity factors which can deviate as much as 80%. The crack length also affects the outcome. Larger errors are committed by the approximate solution for caustics that are closer to the crack tip. The advantage of using the normalized distance from the crack tip is discussed in contrast to using the absolute distance. Incorrect experimental measurements are also discussed in relation to the resulting error for evaluating the crack tip stress intensity factor.     

On the fracture toughness of ferroelastic materials

The toughness enhancement due to domain switching near a steadily growing crack in a ferroelastic material is analyzed. The constitutive response of the material is taken to be characteristic of a polycrystalline sample assembled from randomly oriented tetragonal single crystal grains. The constitutive law accounts for the strain saturation, asymmetry in tension versus compression, Bauschinger effects, reverse switching, and strain reorientation that can occur in these materials due to the non-proportional loading that arises near a propagating crack. Crack growth is assumed to proceed at a critical level of the crack tip energy release rate. Detailed finite element calculations are carried out to determine the stress and strain fields near the growing tip, and the ratio of the far field applied energy release rate to the crack tip energy release rate. The results of the finite element calculations are then compared to analytical models that assume the linear isotropic K-field solution holds for either the near tip stress or strain field. Ultimately, the model is able to account for the experimentally observed toughness enhancement in ferroelastic ceramics.     

The elastostatic plane strain mode I crack tip stress and displacement fields in a generalized linear neo-Hookean elastomer

A general asymptotic plane strain crack tip stress field is constructed for linear versions of neo-Hookean materials, which spans a wide variety of special cases including incompressible Mooney elastomers, the compressible Blatz–Ko elastomer, several cases of the Ogden constitutive law and a new result for a compressible linear neo-Hookean material. The nominal stress field has dominant terms that have a square root singularity with respect to the distance of material points from the crack tip in the undeformed reference configuration. At second order, there is a uniform tension parallel to the crack. The associated displacement field in plane strain at leading order has dependence proportional to the square root of the same coordinate. The relationship between the amplitude of the crack tip singularity (a stress intensity factor) and the plane strain energy release rate is outlined for the general linear material, with simplified relationships presented for notable special cases.     

Mode I and mode II crack tip asymptotic fields with strain gradient effects

The strain gradient effect becomes significant when the size of fracture process zone around a crack tip is comparable to the intrinsic material lengthl, typically of the order of microns. Using the new strain gradient deformation theory given by Chen and Wang, the asymptotic fields near a crack tip in an elastic-plastic material with strain gradient effects are investigated. It is established that the dominant strain field is irrotational. For mode I plane stress crack tip asymptotic field, the stress asymptotic field and the couple stress asymptotic field can not exist simultaneously. In the stress dominated asymptotic field, the angular distributions of stresses are consistent with the classical plane stress HRR field; In the couple stress dominated asymptotic field, the angular distributions of couple stresses are consistent with that obtained by Huang et al. For mode II plane stress and plane strain crack tip asymptotic fields, only the stress-dominated asymptotic fields exist. The couple stress asymptotic field is less singular than the stress asymptotic fields. The stress asymptotic fields are the same as mode II plane stress and plane strain HRR fields, respectively. The increase in stresses is not observed in strain gradient plasticity for mode I and mode II, because the present theory is based only on the rotational gradient of deformation and the crack tip asymptotic fields are irrotational and dominated by the stretching gradient. The project supported by the National Natural Science Foundation of China (19704100), National Natural Science Foundation of Chinese Academy of Sciences (KJ951-1-20), CAS K.C. Wong Post-doctoral Research Award Fund and Post-doctoral Science Fund of China     

Elastostatic crack tip behavior for a rubber-like material

Analyzed in this work is the elastostatic field near a crack tip in a rubber-like material. Asymptotic equations for a crack opened symmetrically about its plane are derived from assumed forms of the strain energy density and constitutive relation that applies to large and finite strain and remains valid even when the strain tends to infinity in the limit. Near field solutions are obtained in regions that decreases and increases in size as the crack tip is approached. Their singular character depends on the constitutive parameters and is evaluated numerically.     

ASYMPTOTIC SOLUTIONS OF MODE I STEADY GROWTH CRACK IN MATERIALS UNDER CREEP CONDITIONS

An asymptotic analysis is made on problems with a steady-state crack growth coupled with a creep law model under tensile loads. Asymptotic equations of crack tip fields in creep materials are derived and solved numerically under small scale conditions. Stress and strain functions are adopted under a polar coordinate system. The governing equations of asymptotic fields are obtained by inserting the stress field and strain field into the material law. The crack growth rate rather than fracture criterion plays an important role in the crack tip fields of materials with creep behavior.     

Effect of crack-tip shape on the near-tip field in glassy polymer

The physical nature of a crack tip is not absolutely sharp but blunt with finite curvature. In this paper, the effects of crack-tip shape on the stress and deformation fields ahead of blunted cracks in glassy polymers are numerically investigated under Mode I loading and small scale yielding conditions. An elastic–viscoplastic constitutive model accounting for the strain softening upon yield and then the subsequently strain hardening is adopted and two typical glassy polymers, one with strain hardening and the other with strain softening–rehardening are considered in analysis. It is shown that the profile of crack tip has obvious effect on the near-tip plastic field. The size of near-tip plastic zone reduces with the increase of curvature radius of crack tip, while the plastic strain rate and the stresses near crack tip enhance obviously for two typical polymers. Also, the plastic energy dissipation behavior near cracks with different curvatures is discussed for both materials.     

Logarithm strain singularity at tip of mode I growing crack in elasticand perfectly-plastic material

Reanalyzed in detail is the stress and strain distribution near the tip of a Mode I steadily growing crack in an elastic and perfectly-plastic material. The crack tip region is divided into five angular sectors, one of which is singular in character and represents a rapid transition zone that becomes a line of strain discontinuity in the limit as crack tip is approached. It is shown for an incompressible material (ν=0.5) under plane strain that the local strain in all the angular sectors possesses the same logarithm singularity, i.e., In r where r is the radial distance measured from the crack tip. This result also prevails for the compressible material ( v < 0.5) and resolves a long standing controversy concerning the strain singularity in the sector just ahead of the crack tip.     

A transverse crack tip field in bimaterial

The asymptotic field near an interface crack tip is analyzed with the fully nonlinear theory. By dividing the crack tip field into narrowing sectors and an expanding sector, the asymptotic equations for the crack tip field are derived and solved. The singular characters of stress and strain near the crack tip are revealed.     

断裂力学判据的评述

从Inglis 和Griffith 的著名论文到Irwin 和Rice 等的奠基性贡献,对断裂力学中的线弹性断裂力学的K判据,界面断裂力学的G判据,和弹塑性断裂力学的J 判据作了扼要的综述. 介绍了在界面断裂力学G判据的基础上提出的界面断裂力学的K判据,以说明断裂力学的判据存在改进的可能性. 在综述中归纳出断裂力学判据中目前还没有较好解决的几个问题. 在总结以往断裂力学研究经验的基础上,指出裂纹端应力奇异性的源是对断裂力学判据存在的问题作进一步研究的切入点. 探讨了裂纹端应变间断的奇点是裂纹端应力奇异性的源的问题,从而对裂纹端应力强度因子的物理意义进行了讨论. 最后,阐述了进行可靠的裂纹端应力场的弹塑性分析是改进弹塑性断裂力学判据的关键,而进行可靠的裂纹端应力场的弹塑性分析的前提是要通过裂纹端应力奇异性的源的研究来获得作用在裂纹端的造成裂纹端应变间断的有限值应力.      

Field structure at mode III dynamically propagating crack tip in elastic-viscoplastic materials

An elastic-viscoplastic mechanics model is used to investigate asymptotically the mode Ⅲ dynamically propagating crack tip field in elastic-viscoplastic materials. The stress and strain fields at the crack tip possess the same power-law singularity under a linear-hardening condition. The singularity exponent is uniquely determined by the viscosity coefficient of the material. Numerical results indicate that the motion parameter of the crack propagating speed has little effect on the zone structure at the crack tip. The hardening coefficient dominates the structure of the crack-tip field. However, the secondary plastic zone has little influence on the field. The viscosity of the material dominates the strength of stress and strain fields at the crack tip while it does have certain influence on the crack-tip field structure. The dynamic crack-tip field degenerates into the relevant quasi-static solution when the crack moving speed is zero. The corresponding perfectly-plastic solution is recovered from the linear-hardening solution when the hardening coefficient becomes zero.     

NiTi形状记忆合金裂纹尖端热力耦合行为研究

本文对NiTi形状记忆合金I型裂纹尖端热力耦合行为进行了数值仿真分析和实验验证。建立了包含相变和热力耦合的本构模型,通过有限元计算得到了裂纹尖端附近的纵向应变、马氏体体积分数和温度场分布,依据马氏体相变情况对裂纹尖端有效应力强度因子进行了修正,揭示了加载速率对形状记忆合金裂纹尖端有效应力强度影子的影响规律。参数研究表明,随着加载频率的增加,裂纹尖端附近温度逐渐升高,马氏体相变区域逐渐缩小,有效应力强度因子呈下降趋势,形状记忆合金表现出增韧效应,有助于减缓裂纹扩展。本研究结果对于揭示热力耦合作用下超弹性形状记忆合金疲劳裂纹扩展规律具有重要参考意义。     

新型各向异性核工业石墨断裂力学行为的实验研究和数值分析

本文分别采用激光和白光DSCM(数字散斑相关测量)方法对一种新型各向异性核工业石墨的裂纹尖端位移、应变场进行了实验研究，两种方法都取得了较好的结果。考虑核工业石墨制备过程形成的各向异性特点，本文构建了三维各向异性有限元模型，采用奇异单元，计算模拟石墨裂纹尖端的变形和应力场，通过对实验结果和有限元计算结果的比较可以发现两者具有相近的趋势。     

Damage analysis of tetragonal perovskite structure ceramics implicated by asymptotic field solutions and boundary conditions

Cracking of ceramics with tetragonal perovskite grain structure is known to appear at different sites and scale level. The multiscale character of damage depends on the combined effects of electromechanical coupling, prevailing physical parameters and boundary conditions. These detail features are exhibited by application of the energy density criterion with judicious use of the mode I asymptotic and full field solution in the range of r/a=10⁻⁴ to 10⁻² where r and a are, respectively, the distance to the crack tip and half crack length. Very close to the stationary crack tip, bifurcation is predicted resembling the dislocation emission behavior invoked in the molecular dynamics model. At the macroscopic scale, crack growth is predicted to occur straight ahead with two yield zones to the sides. A multiscale feature of crack tip damage is provided for the first time. Numerical values of the relative distances and bifurcation angles are reported for the PZT-4 ceramic subjected to different electric field to applied stress ratio and boundary conditions that consist of the specification of electric field/mechanical stress, electric displacement/mechanical strain, and mixed conditions. To be emphasized is that the multiscale character of damage in piezoceramics does not appear in general. It occurs only for specific combinations of the external and internal field parameters, elastic/piezoelectric/dielectric constants and specified boundary conditions.     

Large deformation field near a crack tip in rubber-like material

This paper deals with strain field near a crack tip in a rubber-like material under plane strain condition. The constitutive relation adopted here is valid for both small and large strain. The asymptotic equations are derived for a shrinking sector and expanding sector. The closed mathematic solution is obtained for the latter while a numerical solution is found for the former. By connecting deformation of the two sectors, the crack tip field character is found.     

Study on fracture behavior of ferroelectric ceramics under combined electromechanical loading by using a moiré interferometry technique

This paper discusses an in situ observation of fracture behavior around a crack tip in ferroelectric ceramics under combined electromechanical loading by use of a moiré interferometry technique. The deformation field induced by the electric field and the stress concentration near the crack tip in three-points bending experiments was measured. By analysis of the moiré images it is found that under a constant mechanical load, the electric field almost has no effect on the crack extension in the case that the directions of the poling, electric field and crack extension are perpendicular to each other. When the poling direction is parallel to the crack extension direction and perpendicular to the electric field, the strain decreases faster than that calculated by FEM with and without electrical loading as one goes away from the crack tip. In addition, as the electric field intensity increases, the strain near the crack tip increases, and the strain concentration becomes more significant. The project supported by the National Natural Science Foundation of China (10132010, 10025209, 10232023)     

Field structure at mode Ⅲ dynamically propagating crack tip in elastic-viscoplastic materials

An elastic-viscoplastic mechanics model is used to investigate asymptotically the mode Ⅲ dynamically propagating crack tip field in elastic-viscoplastic materials. The stress and strain fields at the crack tip possess the same power-law singularity under a linear-hardening condition. The singularity exponent is uniquely determined by the viscosity coefficient of the material. Numerical results indicate that the motion parameter of the crack propagating speed has little effect on the zone structure at the crack tip. The hardening coefficient dominates the structure of the crack-tip field. However, the secondary plastic zone has little influence on the field. The viscosity of the material dominates the strength of stress and strain fields at the crack tip while it does have certain influence on the crack-tip field structure. The dynamic crack-tip field degenerates into the relevant quasi-static solution when the crack moving speed is zero. The corresponding perfectly-plastic solution is recovered from the linear-hardening solution when the hardening coefficient becomes zero.     

Asymptotic analysis of growing plane strain tensile cracks in elastic-ideally plastic solids

An exact asymptotic analysis is presented of the stress and deformation fields near the tip of a quasistatically advancing plane strain tensile crack in an elastic-ideally plastic solid. In contrast to previous approximate analyses, no assumptions which reduce the yield condition, a priori, to the form of constant in-plane principal shear stress near the crack tip are made, and the analysis is valid for general Poisson ratio ν. Specific results are given for ν = 0.3 and 0.5, the latter duplicating solutions in previous work by L.I. Slepyan, Y.-C. Gao and the present authors. The crack tip field is shown to divide into five angular sectors of four different types ; in the order in which these sweep across a point in the vicinity of the advancing crack, they are : two plastic sectors which can be described asymptotically (i.e., as r → 0, where r is distance from the crack tip) in slip-line terminology as ‘constant stress’ and ‘centered fan’ sectors, respectively ; a plastic sector of non-constant stress which cannot be described asymptotically in terms of slip lines; an elastic unloading sector; and a trailing plastic sector of the same type as that directly preceding the elastic sector. Further, these four different sector types constitute the full set of asymptotically possible solutions at the crack tip. As is known from prior work, the plastic strain accumulated by a material point passing through such a moving ‘centered fan’ sector is O(ln r) as r → 0 ; it is proved in the present work that the plastic strain accumulated by a material point passing through the ‘constant stress’ sector ahead of a growing crack must be less singular than In r as r → 0. As suggested also in earlier studies, the rate of increase of opening gap δ at a point currently at a distance r behind, but very near, the crack tip is given for crack advance under contained yielding by

$\text{δ}\text{?}\text{=}\text{α}\text{J}\text{?}\text{σ}{}_0\text{+β(}\text{σ}{}_0\text{E}\text{)}\text{a}\text{?}\text{ln(}\text{R}\text{r}\text{)}$

where a is crack length, σ0 is tensile yield strength, E is Young's modulus, J is the value of the J-integral taken in surrounding elastic material, and the parameters α and R are undetermined by the asymptotic analysis. The exact solution for ν = 0.3 gives β = 5.462, which agrees very closely with estimates obtained from finite element solutions. An approximate analysis based on use of slip line representations in all plastic sectors is outlined in the Appendix.     

Permeable cracks between two dissimilar piezoelectric materials

An interfacial crack with electrically permeable surfaces between two dissimilar piezoelectric ceramics under electromechanical loading is investigated. An exact expression for singular stress and electric fields near the tip of a permeable crack between two dissimilar anisotropic piezoelectric media are obtained. The interfacial crack-tip fields are shown to consist of both an inverse square root singularity and a pair of oscillatory singularities. It is found that the singular fields near the permeable interfacial crack tip are uniquely characterized by the real valued stress intensity factors proposed in this paper. The energy release rate is obtained in terms of the stress intensity factors. The exact solution of stress and electric fields for a finite interfacial crack problem is also derived.     

铁中Ⅰ型裂纹裂尖场与裂尖形变机制分析

应用有限元及连续介质力学计算了平面应交条件下体心立方铁中不同取向裂纹的裂尖应力场和弹性应变能密度分布,从宏微观相结合角度分析了裂尖场分布与裂尖微结构演化的相互关联.指出裂尖塑性变形的具体形式与裂尖滑移面上分切应力的大小密切相关,并从能量角度解释了裂尖相变产生的原因,最后结合相关分子动力学研究成果探讨了裂尖奇异性区域.