Ion Beam Modification of Polymethyl methacrylate (PMMA) Polymer Matrix Filled with Organometallic Complex

A Nickel Dimethylglyoxime (Ni‐DMG) compound was dispersed in polymethyl methacrylate (PMMA) films at different concentrations. PMMA was synthesized by a solution polymerization technique. These films were irradiated with 120 MeV Ni¹⁰⁺ ions at the fluences of 1×10¹¹ and 1×10¹² ions/cm². The radiation induced changes in dielectric properties and average surface roughness were investigated by using an LCR meter in the frequency range 50 Hz to 10 MHz and atomic force microscopy (AFM), respectively. The electrical properties of irradiated films are found to increase with the fluence and also with the concentration of Ni‐DMG. From the analysis of frequency, f, dependence of dielectric constant, ?, it has been found that the dielectric response in both pristine and irradiated samples obey the Universal law given by ? α f ^n?1. The dielectric constant/loss is observed to change significantly due to the irradiation. This suggests that ion beam irradiation promotes (i) the metal to polymer bonding (ii) convert the polymeric structure in to hydrogen depleted carbon network due to the emission of hydrogen gas and/or other volatile gases. Atomic force microscopy (AFM) shows that the average surface roughness and surface morphology of irradiated films are observed to change.     

Dielectric properties and surface morphology of swift heavy ion beam irradiated polycarbonate films

Swift heavy ion beam irradiation induces modification in the dielectric properties and surface morphologies of polycarbonate (PC) films. The PC films were irradiated by 55 MeV energy of C⁵⁺ beam at various ions fluences ranging from 1 × 10¹¹ to 1 × 10¹³ ions cm^?2. The dielectric properties (i.e., dielectric constant, dielectric loss, and AC conductivity) and surface morphologies of pristine and SHI beam irradiated PC films were investigated by dielectric measurements, atomic force microscopy (AFM), and optical microscopy. The dielectric measurements show that the dielectric constant, dielectric loss, and AC conductivity increase with ion fluences and temperature, however, the dielectric constant and AC conductivity decrease while dielectric loss increases with frequency. AFM shows the increase in average roughness values with ion fluences. The change of color in PC films has been observed from colorless to yellowish and then dark brown with increases of ion fluence by using optical microscopy.     

PMMA: A key macromolecular component for dielectric low-κ hybrid inorganic-organic polymer films

Inorganic-organic composite and hybrid films find widespread applications for the development of functional materials. Polymer matrices with embedded inorganic fillers, nanoparticles or clusters are particularly appealing for optical, electronic, dielectric and magnetic applications. In particular, the development of hybrid layers with tailored dielectric properties represents a key issue in many technological fields.In this framework, poly(methyl methacrylate) (PMMA), due to its outstanding chemico-physical properties, represents a particularly suitable polymer component for the embedding of both microscopic and nanoscopic functional inorganic fillers. The wide use of such a matrix has to be traced back to the favourable combination of chemical and physical properties and easy processing. In this review, the main features and properties of PMMA, with a particular focus on dielectric ones, are firstly briefly described. Selected examples to illustrate the state-of-the art of its corresponding use as dielectric matrix are given and several examples are provided and surveyed.Finally, three case studies concerning PMMA-based hybrid films, produced for very different application fields, are described and discussed. The first example deals with the entrapment of micrometric zinc sulphide powders in PMMA, which acts as a host matrix for the electroluminescent particles in thick film-based Alternate Current Powder Electroluminescent Lamps (ACPELs). The second example describes the preparation of low-κ inorganic-organic hybrid dielectric films based on a PMMA-polyvinylchloride(PVC) blend and a hydrophobic silica powder functionalised on the surface with trimethylsiloxane groups (m-SiO₂). The composition of the investigated materials is [(PMMA)_x(PVC)_y]/(m-SiO₂)_z with z ranging from 0 to 38.3 wt% and x = y = (100 − z)/2. The third case concerns the use of PMMA as a matrix to embed zirconium oxoclusters through the formation of covalent bonds. The obtained material, characterised by a dielectric constant value remarkably lower (1.93 at 1 kHz and 25 °C) than in pristine PMMA (3.0 at 1 kHz and 25 °C), appears as very appealing for the development of microelectronic devices based on low dielectric constant polymer films such as, for instance, field-effect transistor (FET).These three cases are paradigms of three different approaches to composite and hybrid materials based on the embedding of particles in PMMA polymer matrix.     

Medium energy,heavy and inert ion irradiation of metallic thin films: studies of surface nano‐structuring and metal burrowing

In context to the ion induced surface nanostructuring of metals and their burrowing in the substrates, we report the influence of Xe and Kr ion‐irradiation on Pt:Si and Ag:Si thin films of ~5‐nm thickness. For the irradiation of thin films, several ion energies (275 and 350 keV of Kr; 450 and 700 keV of Xe) were chosen to maintain a constant ratio of the nuclear energy loss to the electronic energy loss (S_n/S_e) in Pt and Ag films (five in present studies). The ion‐fluence was varied from 1.0 × 10¹⁵ to 1.0 × 10¹⁷ ions/cm². The irradiated films were characterized using Rutherford backscattering spectroscopy (RBS), atomic force microscopy (AFM) and scanning electron microscopy (SEM). The AFM and SEM images show ion beam induced systematic surface nano‐structuring of thin films. The surface nano‐structures evolve with the ion fluence. The RBS spectra show fluence dependent burrowing of Pt and Ag in Si upon the irradiation of both ion beams. At highest fluence, the depth of metal burrowing in Si for all irradiation conditions remains almost constant confirming the synergistic effect of energy losses by the ion beams. The RBS analysis also shows quite large sputtering of thin films bombarded with ion beams. The sputtering yield varied from 54% to 62% by irradiating the thin films with Xe and Kr ions of chosen energies at highest ion fluence. In the paper, we present the experimental results and discuss the ion induced surface nano‐structuring of Pt and Ag and their burrowing in Si. Copyright © 2016 John Wiley & Sons, Ltd.     

An effect of N ion bombardment on the properties of CdTe thin films

E-beam evaporated CdTe thin films were processed with N⁺ ion bombardment as in situ process. The N⁺ ion glow was generated using simple Multipurpose Al probe instead of conventional plasma sources. The prepared films were identified as nano crystalline using XRD analysis. High N⁺ ion fluence helped to grow (3 1 1) oriented CdTe thin films instead of (2 2 0) and (1 1 1). The observed results revealed the effect of N⁺ ion fluence on the structural parameters like lattice parameter, d space value, crystalline size, dislocation density, micro strain etc. The observed optical band gap values lie in between 1.47 and 1.77 eV. The effect of N⁺ ion bombardment on optical properties was also reported. Noticeable change in electrical and surface properties was also observed. The observed value shows the reproducibility as <1% and it is suggested that the N⁺ ion plasma was effectively utilized to modify the structural, optical and surface properties as in situ.     

Ion‐beam‐induced morphology on the surface of thin polymer films at low current density and high ion fluence

The effect of Xe⁺ bombardment on the surface morphology of four different polymers, polystyrene (PS), poly(phenylene oxide), polyisobutylene, and polydimethylsiloxane, was investigated in ion energy and fluence ranges of interest for secondary ion mass spectrometry depth‐profiling analysis. Atomic force microscopy (AFM) was applied to analyze the surface topography of pristine and irradiated polymers. AFM analyses of nonirradiated polymer films showed a feature‐free surface with different smoothness. We studied the influence of different Xe⁺ beam parameters, including the incidence angle, ion energy (660–4000 eV), current density (0.5 × 10² to 8.7 × 10² nA/cm²), and ion fluence (4 × 10¹⁴ to 2 × 10¹⁷ ion/cm²). Xe⁺ bombardment of PS with 3–4 keV at a high current density did not induce any change in the surface morphology. Similarly, for ion irradiation with lower energy, no surface morphology change was found with a current density higher than 2.6 × 10² nA/cm² and an ion fluence up to 4 × 10¹⁶ ion/cm². However, Xe⁺ irradiation with a lower current density and a higher ion fluence led to topography development for all of the polymers. The roughness of the polymer surface increased, and well‐defined patterns appeared. The surface roughness increased with ion irradiation fluence and with the decrease of the current density. A pattern orientation along the beam direction was visible for inclined incidence between 15° and 45° with respect to the surface normal. Orientation was not seen at normal incidence. The surface topography development could be explained on the basis of the balance between surface damage and sputtering induced by the primary ion beam and redeposition–adsorption from the gas phase. Time‐of‐flight secondary ion mass spectrometry analyses of irradiated PS showed strong surface modifications of the molecular structure and the presence of new material. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 39: 314–325, 2001     

Fabrication and characterization of Meldola's blue/zinc oxide hybrid electrodes for efficient detection of the reduced form of nicotinamide adenine dinucleotide at low potential

We report the synthesis and the electrochemical properties of hybrid films made of zinc oxide (ZnO) and Meldola's blue dye (MB) using cyclic voltammetry (CV). MB/ZnO hybrid films were electrochemically deposited onto glassy carbon, gold and indium tin oxide-coated glass (ITO) electrodes at room temperature (25 ± 2 °C) from the bath solution containing 0.1 M Zn(NO₃)₂, 0.1 M KNO₃ and 1 × 10⁻⁴ M MB. The surface morphology and deposition kinetics of MB/ZnO hybrid films were studied by means of scanning electron microscopy (SEM), atomic force microscopy (AFM) and electrochemical quartz crystal microbalance (EQCM) techniques, respectively. SEM and AFM images of MB/ZnO hybrid films have revealed that the surfaces are well crystallized, porous and micro structured. MB molecules were immobilized and strongly fixed in a transparent inorganic matrix. MB/ZnO hybrid films modified glassy carbon electrode (MB/ZnO/GC) showed one reversible redox couple centered at formal potential (E⁰′) −0.12 V (pH 6.9). The surface coverage (Γ) of the MB immobilized on ZnO/GC was about 9.86 × 10⁻¹² mol cm⁻² and the electron transfer rate constant (ks) was determined to be 38.9 s⁻¹. The MB/ZnO/GC electrode acted as a sensor and displayed an excellent specific electrocatalytic response to the oxidation of nicotinamide adenine dinucleotide (NADH). The linear response range between 50 and 300 μM NADH concentration at pH 6.9 was observed with a detection limit of 10 μM (S/N = 3). The electrode was stable during the time it was used for the full study (about 1 month) without a notable decrease in current. Indeed, dopamine (DA), ascorbic acid (AA), acetaminophen (AP) and uric acid (UA) did not show any interference during the detection of NADH at this modified electrode.     

Electrical and positron annihilation study on epoxy and epoxy acrylate composites

Epoxy acrylate resin was prepared by endcapping the acrylic acid to epoxy resin backbone in the presence of triphenyl phosphene as catalyst. The structure was elucidated by IR and NMR spectroscopy. Epoxy and epoxy acrylate composites were prepared by mixing different concentrations of mica, magnesium hydroxide and calcium silicate with each epoxy/hardener and epoxy acrylate/styrene mixtures, respectively. The permittivity ε′, dielectric loss ε′′ and loss tangent tan δ were measured for these composites in the frequency range (10²-10⁶ Hz) and at 30 °C. The data obtained were analyzed into two absorption regions related to Maxwell-Wagner effect and to some local molecular motions rather than the main chain motion. The higher values of ε′ and the lower values of tan δ given for the composites containing the epoxy acrylate resin indicate some improvement in the dielectric properties when compared with those containing the epoxy resin. The effect of filler type and filler content on the positron annihilation lifetime and its intensity as well as S-parameter for epoxy and epoxy acrylate composites were also studied. The high values of S-parameter noticed by with increasing filler content indicates some increase in free electrons which lead to an increase in electrical conductivity. The highest value of hardness was obtained in the case of calcium silicate followed by mica and magnesium hydroxide.     

Growth and characterization of molybdenum oxide thin films prepared by photochemical metal–organic deposition (PMOD)

Molybdenum oxide thin films have been successfully prepared by direct UV irradiation of amorphous films of a molybdenum dioxide acetylacetonate complex on Si(1 0 0) substrates. Photodeposited films were characterized by X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) and the surface morphology examined by Atomic Force Microscopy (AFM). It was found that as-photodeposited films are uniform and smooth, with thickness of 350 nm, with rms surface roughness of 28 nm and contain non-stoichiometric oxides (MoO_3−x). The results of XRD analysis showed that post-annealing of the films in air at 450 °C transforms the sub-oxides to α-MoO₃ phase with a much rougher surface morphology (rms = 144 nm). The as-photodeposited MoO_3−x films are amorphous, and exhibit better optical quality than annealed films.     

Crystal phase transformations within propylene/hexene-1 copolymers films as induced by direct current discharge treatment

The effect of a direct current discharge on the films of polypropylene and copolymers of propylene and hexene-1 synthesized with an isospecific catalytic system, rac-Me₂SiInd₂ZrCl₂-polymethylaluminoxane, was investigated. The treatment of isotactic polypropylene films by the discharge did not affect the ratio of crystalline phases in the polymer to a measurable extent. However, for the plasma treated films of copolymers of propylene and hexene-1 (the hexene-1 content of 1-2 mol%), a structural transformation of γ-modification into α-modification has been noticed. The observed phase transition has no apparent relation to any changes in microstructure of the copolymer chain because melting temperature values and the stereoregularity parameters of the samples remained practically unchanged. An experimental investigation of the specific influence exerted by individual components of a direct current discharge on the crystalline structure of copolymers has been undertaken. The exposure to a quantum component of the discharge did not induce any changes in the phase composition of the irradiated samples. The heating of the samples led to a negligible change of their phase composition. It has been determined that the surface of polypropylene and propylene/hexene-1 copolymer films facing the cathode in the course of the direct current discharge treatment had an accumulated negative charge Q > 10 nC/cm² which persisted for a long time afterwards. It has been suggested that the electrical field of a negative discharge may be the main cause of the γ-into α-phase transition in propylene/hexene-1 copolymers under the plasma effect. To verify this assumption, a propylene/hexene-1 copolymer film was charged under electron beam with energy of 4 keV. The electron beam treatment of the film resulted to the negative charge value of 11 nC/cm². The electron beam irradiation has induced the phase transition which was quite similar to the transition observed as the result of plasma treatment. So, it may be concluded that the phase transition from crystal γ-modification to α-modification under the effect of direct current discharge which has been investigated for copolymers of propylene and hexene-1 is induced by electric field of the negative charge accumulated at the surface layers of the films of the copolymers.     

Synthesis and evaluation of bis-β-diketonate dioxotungsten(VI) complexes as precursors for the photodeposition of WO3 films

In this paper non-stoichiometric tungsten oxide thin films have been successfully prepared by direct UV irradiation of bis-β-diketonate dioxotungsten(VI) precursor complexes spin-coated Si(1 0 0) substrates. Photodeposited films were characterized by Fourier transform-infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) and the surface morphology examined by Atomic Force Microscopy (AFM). The results of XRD analysis showed that the as-photodeposited WO_3−x films are amorphous and have a rougher surface than thermally treated films. Post-annealing of the films in air at 500 °C transforms the sub-oxides to a monoclinic WO₃ phase.     

Effects of X-ray radiation on the surface chemical composition of plasma deposited thin fluorocarbon films

Different thin fluorocarbon (FC) films were deposited on Si(111) using plasma polymerisation and then exposed to X-ray radiation. Changes in the chemical composition of the deposited fluorocarbon films as a function of irradiation time were investigated in situ using X-ray photoelectron spectroscopy. The evaluation of the C1s and F1s core level induced emission as a function of exposure to X-ray radiation (Mg Kα, hν = 1253.6 eV) reveals changes in the surface chemical composition of the FC polymer structure. The presented results indicate a high defluorination under X-ray irradiation. Additionally, binding energy shifts of the F1s and C1s peaks during the exposure associated with surface charging effects were observed. With ongoing exposure the surface charging decreases continuously and the FC surfaces become more conductive due to changes in the polymer structure. Different models have been used to describe the decomposition kinetics and surface composition.     

The effects of energetic ion irradiation on metal-to-polymer adhesion

In this study, the simple and effective surface modification of polymers through ion irradiation is described to improve metal-to-polymer adhesion. The surface of polymer films was irradiated with 150 keV Xe⁺ ions at various fluences, and copper (Cu) was then deposited onto the surface-modified polymer films. The surface properties of the modified films were investigated in terms of their wettability, chemical composition, and surface morphology. The metal-to-polymer adhesion strength was estimated using a nano-indenter. As a result, the surface environment of the polymer films was physiochemically changed by ion irradiation, which could have a significant effect on the metal-to-polymer adhesion. The irradiated polymer films exhibited a higher adhesion strength than the control film, and the strength depended on the fluence. The maximum adhesion strength (8.45 mN) of the Cu deposited on the irradiated PEN films was obtained at a fluence of 5×10¹⁴ ions/cm².     

Optical Properties of Swift Heavy Ion Beam Irradiated Polycarbonate/Polystyrene Composites Films

Polycarbonate/polystyrene composites films were irradiated by 55 MeV Carbon ion beam with fluence ranging from 1 × 10¹¹ to 1 × 10¹³ ions/cm². The polymer composites films were prepared by solution mixing method. The effects of ion beam on structural, optical and surface morphology of PC/PS composites films were investigated by X-ray diffraction (XRD), UV-visible spectroscopy (UV-vis), Fourier Transform Infrared Spectroscopy (FT-IR) and Optical Microscope. The XRD pattern shows the average crystallite size, percentage of crystallinity and inter-chain separation, which decreases with increase in ion fluences. UV-vis spectra show that the energy band gap and transmittance decreases while number of carbon atoms increases with fluences. The FT-IR spectra evidenced very small change in cross linking and chain scissoring at high ion fluences, while the optical microscopy shows a color change with ion fluence.     

100 keV H+ ion irradiation of as‐deposited Al‐doped ZnO thin films: An interest in tailoring surface morphology for sensor applications

We report the influence of 100 keV H⁺ ion beam irradiation on the surface morphology, crystalline structure, and transport properties of as‐deposited Al‐doped ZnO (Al:ZnO) thin films. The films were deposited on silicon (Si) substrate by using DC sputtering technique. The ion irradiation was carried out at various fluences ranging from 1.0 × 10¹² to 3.0 × 10¹⁴ ions/cm². The virgin and ion‐irradiated films were characterized by X‐ray diffraction, Raman spectroscopy, atomic force microscopy, and Hall probe measurements. Using X‐ray diffraction spectra, 5 points Williamson‐Hall plots were drawn to deduce the crystallite site and strain in Al:ZnO films. The analysis of the measurements shows that the films are almost radiation resistant in the structural deformation under chosen irradiation conditions. With beam irradiation, the transport properties of the films are also preserved (do not vary orders of magnitude). However, the surface roughness and the crystallite size, which are crucial parameters of the ZnO film as a gas sensor, are at variation with the ion fluence. As ion fluence increases, the root‐mean‐square surface roughness oscillates and the surface undergoes for smoothening with irradiation at chosen highest fluence. The crystallite size decreases initially, increases for intermediate fluences, and drops almost to the value of the pristine film at highest fluence. In the paper, these interesting experimental results are discussed in correlations with ion‐matter interactions especially energy losses by the ion beam in the material.     

Photophysical properties and photostability of novel unsymmetric polycyclicphenazine-type D-π-A fluorescent dyes and the dye-doped films

Structural isomers of unsymmetric polycyclicphenazine-type D-π-A fluorescent dyes have been newly synthesized and characterized in both solution and polymer films. The dyes exhibited two strong absorption bands at around 328-401 nm and 516-532 nm, and an intense fluorescence band at around 595-629 nm (Φ = 0.32-0.84) in 1,4-dioxane. The dye-doped polymer films showed good ability of wavelength conversion; the films can efficiently convert ultraviolet and green-yellow lights into red light (Φ = 0.43-0.86). Moreover, the photostability of the dyes-doped PS, PMMA, and PLA films has been investigated.     

Ionic transport in P(VDF-HFP)-PMMA-LiCF3SO3-(PC + DEC)-SiO2 composite gel polymer electrolyte

Composite gel polymer electrolytes composed of poly(vinylidene fluoride-co-hexafluoropropylene) P(VDF-HFP) and polymethylmethacrylate PMMA polymers, PC + DEC as plasticizer and LiCF₃SO₃ as salt and fumed silica as filler have been synthesized by solvent casting technique with varying plasticizer-filler ratio systematically. Films of thickness in the range of 40-70 μm were characterized by a.c. impedance measurements in the temperature range 303 K to 373 K. Addition of filler to the polymer electrolyte was found to result in an enhancement of the ionic conductivity. A maximum electrical conductivity of ∼1 × 10⁻³ S/cm at 303 K and ∼2.1 × 10⁻³ S/cm at 373 K has been achieved with the dispersion of the SiO₂. FTIR spectral studies confirmed the polymer-salt interaction. XRD patterns exhibit the increased amorphicity in the blended composite gel polymer electrolytes. Scanning electron micrograph shows the dispersion of SiO₂ particle in the polymer electrolyte.     

The diverse effect of antiplasticizer in the molecular dynamics of an organic dye-doped polymer observed at different motional lengthscales

Complementary thermal analysis techniques were used to study blending-induced perturbations in polymer dynamics pertaining to different motional lengthscales. The antiplasticizing role of common neutral and apolar fluorescent perylimides on the cooperative relaxation dynamics of poly(methyl methacrylate) (PMMA) chain segments is evidenced by a clear rise of both the glass transition (T_g) and liquid-liquid transition (T_LL) temperatures. Simultaneously, the dielectric strength, Δε_β, of the signal ascribed to restricted rotational movements of lateral groups, shows a substantial reduction. Most aspects of the observed behavior bear analogies with recent experimental observations in nanoconfined PMMAs (e.g., PMMA with homogeneously dispersed SiO₂ nanospheres, in-situ polymerized in silica nanopores or in the form of supported ultrathin films), suggesting that a common mechanism is operational. In our mixtures, confinement effects, such as a modification in the macroconformation of the polymer, and changes in the orientation and packing of the polymer random coil, provide a plausible explanation of the observed changes regardless of the motional lengthscale concerned. Consonant with this scenario are reports of advanced optical properties for perylimide + PMMA blends, ascribed to the high rigidity of the matrix together with weak intercomponent interactions.     

Synthesis and characterization of p-toluenesulfonate incorporated poly(3,4-ethylenedioxythiophene)

Poly(3,4-ethylenedioxythiophene) (PEDOT), a conducting polymer, was electrochemically synthesized with p-toluenesulfonate (TSNa) as a dopant on gold surface. The electrochemical properties of the polymer were studied by impedance spectroscopy and cyclic voltammetry (CV). It was found that the impedance magnitude of the electrode significantly decreased over a wide range of frequency from 10⁰ to 10⁴ Hz after the polymer deposition. The CV demonstrated enhanced reversibility of the PEDOT film. The surface morphology was investigated by scanning electronic microscope (SEM) and atomic force microscope (AFM). Due to the effect of TSNa structure, nano-fungus was observed. Polymerization time was optimized and 30 min deposition resulted in the highest charge capacity, showing the highest electroactive surface area, possibly due to its porous structured polymer. Moreover, the high specific surface area could be favorable for cell attachment. The stability of PEDOT in glutathione (GSH), a common biologically relevant reducing agent, was studied with polypyrrole (PPy) as a baseline. It showed that the former had much better stability than the latter and it could be an excellent candidate for potential applications of in vivo neural devices.     

Nanocalorimeter fabrication procedure and data analysis for investigations on implantation damage annealing

Nanocalorimetry operates on similar principles as conventional differential thermal analysis, but the thinness of the system provides a mass addenda small enough to observe thermal processes in thin films or at surface, involving energies in the order of the nanojoules. The fabrication procedure of nanocalorimeters used to measure the heat released by damage after low-energy (30 keV) ion implantation in polycrystalline silicon (poly-Si) is described. Nanocalorimeters are fabricated from low-stress Si₃N_x membranes (100 nm) on which a Pt strip (25 nm) is deposited which serves both as a heater and thermometer. Using Pt allows us to carry out the metallization step prior to Si anisotropic chemical etching releasing the rectangular Si₃N_x membrane, so the success yield nearly reaches 100%. A 140 nm Si layer is deposited on the nanocalorimeters. Large-grain (∼75 nm) poly-Si is obtained by annealing at 900 °C for 100 s. The calculation method used to obtain heat rate curves is described, including the corrections necessary to take into account the dissimilarity between sample and reference calorimeters (baseline), and the increased heating rate and associated losses. Examples of heat release after 30 keV Si implantations are presented, showing that the total amount of heat release is characterized by a saturation above a fluence of 1 Si⁻/nm². The similarity observed in the signal shape between low and high fluence measurements also suggests that each impacting ion produces a high damage zone similar to the damage generated by high fluence irradiation. This conclusion is compatible with the annealing of damage zones proposed by molecular dynamic studies. It is also shown that the measured signal is not affected significantly by temperature non-uniformity.