Photoluminescence scanning on InAs/InGaAs quantum dot structures

The photoluminescence spectra of InAs quantum dots (QDs) embedded into four types of In_xGa_1−xAs/GaAs (x = 0.10, 0.15, 0.20 and 0.25) multi quantum well MBE structures have been investigated at 300 K in dependence on the QD position on the wafer. PL mapping was performed with 325 nm HeCd laser (35 mW) focused down to 200 μm (110 W/cm²) as the excitation source. The structures with x = 0.15 In/Ga composition in the In_xGa_1−xAs capping layer exhibited the maximum photoluminescence intensity. Strong inhomogeneity of the PL intensity is observed by mapping samples with the In/Ga composition of x ≥ 0.20-0.25. The reduction of the PL intensity is accompanied by a gradual “blue” shift of the luminescence maximum at 300 K as follows from the quantum dot PL mapping. The mechanism of this effect has been analyzed. PL peak shifts versus capping layer composition are discussed as well.     

Nanostructures on SiC surface created by laser microablation

Silicon carbide (SiC), as it is well-known, is inaccessible to usual methods of technological processing. Consequently, it is important to search for alternative technologies of processing SiC, including laser processing, and to study the accompanying physical processes. The work deals with the investigation of pulsed laser radiation influence on the surface of 6H-SiC crystal. The calculated temperature profile of SiC under laser irradiation is shown. Structural changes in surface and near-surface layers of SiC were studied by atomic force microscopy images, photoluminescence, Raman spectra and field emission current-voltage characteristics of initial and irradiated surfaces. It is shown that the cone-shaped nanostructures with typical dimension of 100-200 nm height and 5-10 nm width at the edge are formed on SiC surface under nitrogen laser exposure (λ = 0.337 μm, t_p = 7 ns, E_p = 1.5 mJ). The average values of threshold energy density 〈W_thn〉 at which formation of nanostructures starts on the 0 0 0 1 and surfaces of n-type 6H-SiC(N), nitrogen concentration n_N ≅ 2 × 10¹⁸ cm⁻³, are determined to be 3.5 J/cm² and 3.0 J/cm², respectively. The field emission appeared only after laser irradiation of the surface at threshold voltage of 1000 V at currents from 0.7 μA to 0.7 mA. The main role of the thermogradient effect in the processes of mass transfer in prior to ablation stages of nanostructure formation under UV laser irradiation (LI) was determined. We ascertained that the residual tensile stresses appear on SiC surface as a result of laser microablation. The nanostructures obtained could be applied in the field of sensor and emitting extreme electronic devices.     

Nonlinear optical properties of periodic gold nanoparticle arrays

Periodic Au nanoparticle arrays were fabricated on silica substrates using nanosphere lithography. The identical single-layer masks were prepared by self-assembly of polystyrene nanospheres with radius R = 350 nm. The structural characterization of nanosphere masks and periodic particle arrays was investigated by atomic force microscopy. The nonlinear optical properties of the Au nanoparticle arrays were determined using a single beam z-scan method at a wavelength of 532 nm with laser duration of 55 ps. The results show that periodic Au nanoparticle arrays exhibit a fast third-order nonlinear optical response with the nonlinear refractive index and nonlinear absorption coefficient being n₂ = 6.09 × 10⁻⁶ cm²/kW and β = −1.87 × 10⁻⁶ m/W, respectively.     

Femtosecond laser embedded grating micromachining of flexible PDMS plates

We report on the femtosecond laser micromachining of photo-induced embedded diffraction grating in flexible Poly (Dimethly Siloxane) (PDMS) plates using a high-intensity femtosecond (130 fs) Ti: sapphire laser (λ_p = 800 nm). The refractive index modifications with diameters ranging from 2 μm to 5 μm were photo-induced after the irradiation with peak intensities of more than 1 × 10¹¹ W/cm². The graded refractive index profile was fabricated to be a symmetric around from the center of the point at which femtosecond laser was focused. The maximum refractive index change (Δn) was estimated to be 2 × 10⁻³. By the X-Y-Z scanning of sample, the embedded diffraction grating in PDMS plate was fabricated successfully using a femtosecond laser.     

Optical and nonlinear optical characteristics of the Ge and GaAs nanoparticle suspensions prepared by laser ablation

The laser ablation of Ge and GaAs targets placed in water and ethanol was carried out using the fundamental radiation of nanosecond Nd:YLF laser. The results of preparation and the optical and nonlinear optical characterization of the Ge and GaAs nanoparticle suspensions are presented. The considerable shift of the band gap energy of the nanoparticles compared to the bulk semiconductors was observed. The distribution of nanoparticle sizes was estimated in the range of 1.5-10 nm on the basis of the TEM and spectral measurements. The nonlinear refractive indices and nonlinear absorption coefficients of Ge and GaAs nanoparticles were defined by the z-scan technique using second harmonic radiation of picosecond Nd:YAG laser (λ = 532 nm).     

Effects of different ions implantation on yellow luminescence from GaN

The influence of C, N, O, Mg, Si and co-implants (Mg+Si) ions implantation with fluences in the wide range 10¹³-10¹⁷ cm⁻² on the yellow luminescence (YL) properties of wurtzite GaN has been studied by photoluminescence (PL) spectroscopy. Two types of n-type GaN samples grown by metal-organic chemical vapor deposition method (MOCVD) and labeled as No-1 and No-2 were studied. In their as-grown states, No-1 samples had strong YL, while No-2 samples had weak YL. Results of the frontside and backside PL measurements in one of the as-grown GaN epifilms are also presented. Comparing the intensity of YL between frontside and backside PL spectra, the backside PL spectrum shows the more intense YL intensity. This implies that most of the intrinsic defects giving rise to YL exist mainly near the interface between the epilayer and buffer layer. Our experimental results show that the intensity ratio of YL to near-band-edge UV emission (I_YL/I_UV) decreases gradually by increasing the C implantation fluence from 10¹³ to 10¹⁶ cm⁻² for No-1 samples after annealing at 900 °C. When the fluence is 10¹⁷ cm⁻², a distinct change of the I_YL/I_UV is observed, which is strongly increased after annealing. For No-2 samples, after annealing the I_YL/I_UV decreases gradually with increase in the C implantation fluence from 10¹³ to 10¹⁵ cm⁻². The I_YL/I_UV is gradually increased with increasing C fluence from 10¹⁶ to 10¹⁷ cm⁻² after annealing, while I_YL/I_UV for other ions-implanted GaN samples decreases monotonically with increase in the ions implantation fluences from 10¹³ to 10¹⁷ cm⁻² for both No-1 samples and No-2 samples. It is noted that for annealed C-implanted No-2 samples I_YL/I_UV is much higher than that of the as-grown one and other ion-implanted ones. In addition, I_YL/I_UV for the Mg, Si, and co-implants (Mg+Si) implanted No-2 samples with a fluence of 10¹³ cm⁻² after being annealed at 900 °C is higher than that of the as-grown one. Based on our experimental data and literature results reported previously, the origins of the YL band have been discussed.     

Line patterning with large refractive index changes in the deep inside of glass by nanosecond pulsed YAG laser irradiation

Nanosecond (∼100 ns) pulsed (10 Hz) Nd:YAG laser operating at the wavelength (λ) of 1064 nm with pulse energies of 0.16-1.24 mJ/cm² has irradiated 10Sm₂O₃·40BaO·50B₂O₃ glass. It is demonstrated for the first time that the structural modification resulting the large decease (∼3.5%) in the refractive index is induced by the irradiation of YAG laser with λ=1064 nm. The lines with refractive index changes are written in the deep inside of 100-1000 μm depths by scanning laser. The line width is 1-13 μm, depending on laser pulse energy and focused beam position. It is proposed that the samarium atom heat processing is a novel technique for inducing structural modification (refractive index change) in the deep interior of glass.     

Laser synthesis of semiconductor nanostructures with narrow band gap

Semiconductor nanostructures with narrow band gap were synthesized by means of laser chemical vapor deposition (LCVD) of elements from iron carbonyl vapors [Fe(CO)₅] under the action of Ar⁺ laser radiation (λ_L = 488 nm) on the Si substrate surface. The temperature dependence of the specific conductivity of these nanostructures in the form of thin films demonstrated typical semiconductor tendency and gave the possibility to calculate the band gap for intrinsic conductivity (E_g) and the band gap assigned for impurities (E_i), which were depended upon film thickness and applied electrical field. Analysis of deposited films with scanning electron microscopy (SEM) and atomic force microscopy (AFM) demonstrated their cluster structure with average size not more than 100 nm. Semiconductor properties of deposited nanostructures were stipulated with iron oxides in different oxidized phases according to X-ray photoelectron spectroscopy (XPS) analysis.These deposited nanostructures were irradiated with Q-switched YAG laser (λ_L = 1064 nm) at power density about 6 × 10⁷ W/cm². This irradiation resulted in the crystallization process of deposited films on the Si substrate surface. The crystallization process resulted in the synthesis of iron carbide-silicide (FeSi_2−xC_x) layer with semiconductor properties too. The width of the band gap E_g of the synthesized layer of iron carbide-silicide was less than for deposited films based on iron oxides Fe₂O_3−x (0 ≤ x ≤ 1).     

43 W picosecond laser and second-harmonic generation experiment

Combining the advantages of diode-end-pumped Nd: YVO₄ and diode-side-pumped Nd: YAG amplifiers, a high average power and high beam quality picosecond laser is designed. The system delivers a picosecond laser with average power of 43.4 W and good beam quality of M² < 1.7. By focusing the high power picosecond laser in LBO crystal, 532 nm green laser with maximal power of 20.8 W is generated and the conversion efficiency of second-harmonic generation reaches 56.4% when 17.7 W green laser obtained from the fundamental frequency laser with power of 31.4 W and beam quality of M² < 1.25.     

Flexible gratings fabricated in polymeric plate using femtosecond laser irradiation

Flexible gratings embedded in poly-dimethlysiloxane (PDMS) were fabricated using femtosecond laser pulses. Photo-induced gratings in a flexible PDMS plate were directly written by a high-intensity femtosecond (130 fs) Ti: Sapphire laser (λ_p=800 nm). Refractive index modifications with 4 μm diameters were photo-induced after irradiation of the femtosecond pulses with peak intensities of more than 1×10¹¹ W/cm². The graded refractive index profile was fabricated to be symmetric around the center of the focal point. The diffraction efficiency of the grating samples is measured by an He-Ne laser. The maximum value of refractive index change (Δn) in the laser-modified regions was estimated to be approximately 3.17×10⁻³.     

Particulate assisted growth of ZnO nanorods and microrods by pulsed laser deposition

Zinc oxide (ZnO) thin films were deposited on the gallium nitride (GaN) and sapphire (Al₂O₃) substrates by pulsed laser deposition (PLD) without using any metal catalyst. The experiment was carried out at three different laser wavelengths of Nd:YAG laser (λ = 1064 nm, λ = 532 nm) and KrF excimer laser (λ = 248 nm). The ZnO films grown at λ = 532 nm revealed the presence of ZnO nanorods and microrods. The diameter of the rods varies from 250 nm to 2 μm and the length varies between 9 and 22 μm. The scanning electron microscopy (SEM) images of the rods revealed the absence of frozen balls at the tip of the ZnO rods. The growth of ZnO rods has been explained by vapor-solid (V-S) mechanism. The origin of growth of ZnO rods has been attributed to the ejection of micrometric and sub-micrometric sized particulates from the ZnO target. The ZnO films grown at λ = 1064 nm and λ = 248 nm do not show the rod like morphology. X-ray photoelectron spectroscopy (XPS) has not shown the presence of any impurity except zinc and oxygen.     

Resonantly enhanced three-photon excitation spectra of lithium

We present the first measurement on the resonantly enhanced three-photon excitation spectra of natural lithium using a Nd:YAG laser pumped dye laser in conjunction with a thermionic diode ion detector. Exploiting the linear and circular polarizations, the np ²P_3/2(8 ? n ? 11) and nf  ²F_7/2 (8 ? n ? 38) series have been observed via three-photon excitation from the ground state. The measured level energies reveal a dynamic shift from calculated values, which increases with an increase of the principal quantum number n. The ac stark shift and line broadening mechanisms are studied as a function of laser intensity. It is noted that the width increases and the line center shifts towards the higher energy side as the laser intensity is increased. The maximum observed shift for the 12f ²F_7/2 line is 0.33 cm⁻¹ corresponding to the laser intensity variation from 1.34 × 10¹² W/m² to 1.03 × 10¹³ W/m², whereas its width increases from 0.36 cm⁻¹ to 0.82 cm⁻¹.     

Microstructuring of fused silica by laser-induced backside wet etching using picosecond laser pulses

The laser-induced backside wet etching (LIBWE) is an advanced laser processing method used for structuring transparent materials. LIBWE with nanosecond laser pulses has been successfully demonstrated for various materials, e.g. oxides (fused silica, sapphire) or fluorides (CaF₂, MgF₂), and applied for the fabrication of microstructures. In the present study, LIBWE of fused silica with mode-locked picosecond (t_p = 10 ps) lasers at UV wavelengths (λ₁ = 355 nm and λ₂ = 266 nm) using a (pyrene) toluene solution was demonstrated for the first time. The influence of the experimental parameters, such as laser fluence, pulse number, and absorbing liquid, on the etch rate and the resulting surface morphology were investigated. The etch rate grew linearly with the laser fluence in the low and in the high fluence range with different slopes. Incubation at low pulse numbers as well as a nearly constant etch rate after a specific pulse number for example were observed. Additionally, the etch rate depended on the absorbing liquid used; whereas the higher absorption of the admixture of pyrene in the used toluene enhances the etch rate and decreases the threshold fluence. With a λ₁ = 266 nm laser set-up, an exceptionally smooth surface in the etch pits was achieved. For both wavelengths (λ₁ = 266 nm and λ₂ = 355 nm), LIPSS (laser-induced periodic surface structures) formation was observed, especially at laser fluences near the thresholds of 170 and 120 mJ/cm², respectively.     

Silicon-rich/silica multilayers: A means to provide a link between the excitonic 1D quantum confinement and the photoluminescence parameters

The photoluminescence properties—intensity I_PL, emission energy E_PL and decay lifetime τ_PL—of silicon-rich silicon oxide (SRSO)/silica (SO) multilayers are investigated as a function of the optical pump flux (φ) of an argon laser and the measurement temperature in four kinds of samples corresponding to different SRSO sublayer thicknesses (namely 0.7, 1.4, 3.3 and 4.5 nm). The excitons created by the incident laser light mainly within the SRSO layers or at the SRSO/silica interface are confined in the multilayer growth direction (normal to the layers). This so-called 1D exciton quantum confinement effect has been independently described by two models (the state filling, the electron-hole exchange interaction). It is shown in this paper that both models are complementary since we have been able to reproduce, on the one hand, flux dependence of main PL features (energy, intensity and lifetime) of all fabricated samples and on the other hand, the evolution of the singlet-triplet energy splitting as a function of the SRSO sublayer thickness.     

Intracavity frequency doubling of an active Q-switched Nd:YAG laser with 2.25 W output power at 473 nm

An active Q-switched diode-end-pumped Nd:YAG laser is reported with 2.9 W output power on the ⁴F_3/2 → ⁴I_9/2 transitions at a pump power of 24 W. With intracavity frequency doubling using a 20-mm-long LBO, a maximum blue output power of 2.25 W is achieved at a repetition rate of 23 kHz. The conversion efficiency from the corresponding Q-switched fundamental output to blue output is 96%. The peak power of the Q-switched blue pulse is up to 610 W with 160 ns pulse width. The fluctuation of the blue output power is less than 4.0% at the maximum output power.     

XRD and XPS analysis of laser treated vanadium oxide thin films

In this work, we present X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) analysis of laser treated vanadium oxide sols. The films were also observed by transmission electron microscopy (TEM) and scanning electron microscopy (SEM) to reveal how the original xerogel structure changes into irregular shaped, layer structured V₂O₅ due to the laser radiation. XRD revealed that above 102 W/cm² the original xerogel structure disappears and above 129 W/cm² the films become totally polycrystalline with an orthorhombic structure. XPS spectra showed O/V ratio increment by using higher laser intensities.     

Substrate effect on excimer laser assisted crystal growth in phosphor Ca0.997Pr0.002TiO3 polycrystalline thin films

Ca_0.997Pr_0.002TiO₃ thin films that show strong red luminescence were successfully prepared by means of an excimer laser assisted metal organic deposition process with a KrF laser at a fluence of 100 mJ/cm² at 100 °C. The CPTO films grew on the silica, borosilicate, and indium-tin-oxide coated glasses. The crystallinity of the Ca_0.997Pr_0.002TiO₃ films depended on the substrates; the borosilicate and indium-tin-oxide coated glasses with a large optical absorption of a KrF laser (λ = 248 nm) were effective for the crystallization for the Ca_0.997Pr_0.002TiO₃. In addition, a high thermal conductivity of the indium-tin-oxide coated glass substrate could also improve the crystallinity due to an enhancement of thermal propagation to the film. Oxygen annealing at 500 °C for 6 h successfully eliminated the oxygen vacancy produced by the laser irradiation, and also remarkably improved the PL emission intensity. Thus, we have shown that substrate properties such as an optical absorbance and a thermal conductivity were quite important factors for the crystal growth and the PL emission for the Ca_0.997Pr_0.002TiO₃ in the excimer laser assisted metal organic deposition process.     

Accumulation morphology on the surface of stainless steel irradiated by a nanosecond Nd:YAG pulsed laser

In this study, results in the irradiation of stainless steel AISI 304 in air with nanosecond laser pulses at laser irradiation power density 4×10⁷ W/cm² are reported. Laser processing parameters, such as wavelengths 532 and 1064 nm, pulse duration 20 ns and repetition rate 10 Hz were used. It is shown that the surface morphology of the stainless steel is related to the number of pulses applied to the same spot. The following surface morphological changes were observed: (i) occurrence of the micro-grains microstructures at wavelengths 532 and 1064 nm after 10 000 pulses irradiation and (ii) occurrence of vermiform-like microstructures at wavelength 1064 nm after 1000 pulses irradiation. Generally, it is concluded that irradiation due to several consecutive pulses caused significant damage and enhanced the stainless steel surface roughness.     

Comparative analysis of multi-wave mixing and measurements of the higher-order nonlinearities in resonant media

The features of degenerate multi-wave mixing in resonant media (dye solutions) have been studied theoretically and experimentally. It has been demonstrated that thermal nonlinearity due to the induced absorption from the excited level contributes significantly to the efficiency of four-wave mixing, but results in lower efficiency of higher-order interactions. The measurement results obtained for the energy efficiency of four-, six- and eight-wave mixing enable calculations of the third-, fifth- and seventh-order nonlinear optical susceptibilities, respectively. Experimentally, the method proposed for measurements of the higher-order nonlinearities has been realized with the use of the multi-wave mixing at second harmonic λ = 532 nm of monopulse YAG:Nd³⁺ laser radiation in a Rhodamine 6G dye solution. The ratios ∣χ⁽⁵⁾∣/∣χ⁽³⁾∣ and ∣χ⁽⁷⁾∣/∣χ⁽⁵⁾∣ are determined to be of the order of 10⁻⁵ cm³/erg.     

Raman study of BiFeO3 with different excitation wavelengths

Raman spectra of bismuth ferrite (BiFeO₃) over the frequency range of 100-1500 cm⁻¹ have been systematically investigated with different excitation wavelengths. The intensities of the two-phonon modes are enhanced obviously under the excitation of 532 nm wavelength. This is attributed to the resonant behavior when incident laser energy closes to the intrinsic bandgap of BiFeO₃. The Raman spectra of BiFeO₃ excited at 532 nm were measured over the temperature range from 77 to 678 K. Besides the abnormal changes of the peak position and the linewidth of the A₁ mode at 139 cm⁻¹, the prominent frequency shift, the line broadening and the decrease of the intensity for the two-phonon mode at 1250 cm⁻¹ were observed as the temperature increased to Néel temperature (T_N). All these results indicate the existence of strong spin-phonon coupling in BiFeO₃.