Boron trifluoride-catalyzed degradation of poly--caprolactone at ambient temperature

Poly--caprolactone (PCL) can be accelerated to degrade in the presence of boron trifluoride at ambient temperature. The degradation behaviors were studied by using the inherent viscosity measurement, gel permeation chromatography (GPC), infrared analysis (FTIR), nuclear magnetic resonance analysis (NMR), and thermal analysis (DSC). With increasing the addition amount of boron trifluoride, the molecular weight of PCL decreases; the molecular weight distribution is broadened; and the degree of crystallinity of PCL increases at first at low BF₃ level, then decreases when BF₃ content exceeds to 2.64 wt%. The results of IR, ¹HNMR and GPC reveal that -caprolactone monomer does not occur and the main degradation products are the oligomers of PCL with low molecular weight. The mechanism for boron trifluoride-catalyzed degradation of PCL is discussed.     

Particle size and concentration of poly(-caprolactone) and adipate modified starch blend on mineralization in soils with differing textures

The objective of this study was to evaluate the effect of particle size and concentration of poly(-caprolactone) and adipate modified starch blend on mineralization in soils with differing textures, comparing it with polyethylene under the same experimental conditions. Two soil types were used: a Kandiudalfic Eutrudox with a clayey texture and an Arenic Hapludult with a sandy texture. The two different plastic specimens were incorporated in the form of plastic films with three increasing particle sizes and six doses, from 0 to 2.5 mg C g⁻¹ soil. Each plastic dose was incorporated into 200 g of soil placed in a hermetically closed jar at 28 °C, and incubated for a 120-day period to determine CO₂ evolution. Once again it was confirmed that polyethylene is almost non-biodegradable, in contrast to PCL/S, which can be defined as a biodegradable material. Soil texture affected the mineralization kinetics of the plastic specimens, with higher values for the clayey soil. No changes in soil microbial biomass-C or -N were observed by adding polyethylene and PCL/S to the soil. Also, no significant differences were observed on seed emergence and development of rice seedlings (Oryza sativa L.) in plastic modified soil.     

Monomer insertion mechanism of ring-opening polymerization of -caprolactone with yttrium alkoxide intermediate: A DFT study

The mechanism of -caprolactone (CL) insertion into a Y–OCH₃ bond was investigated using density functional theory (DFT) calculations. The optimized geometries and corresponding Gibbs-free energies of the intermediates were obtained, which confirmed a four-step coordination-insertion mechanism. The coordination of CL onto yttrium center led to a nucleophilic addition of the carbonyl group of CL, followed by an intramolecular alkoxide ligand exchange. A monomer insertion was completed by the CL ring opening via acyl–oxygen bond cleavage. The formation of the five-coordinated yttrium intermediate, 3, was found to be the rate-determining step. This study could be applicable to ring-opening polymerisation (ROP) of CL initiated by lanthanide metal complexes.     

Degradation of copolymers obtained by ring-opening polymerization of glycolide and -caprolactone: A high resolution NMR and ESI-MS study

Electrospray ionization-mass spectrometry (ESI-MS) and proton nuclear magnetic resonance (¹H NMR) have been used to investigate the hydrolytic degradation of copolymers obtained by bulk ring-opening copolymerization of glycolide and -caprolactone with monomer ratios ranging from 70/30 to 30/70. NMR allows changes of the average sequence distribution and composition of the components to be followed. In contrast, ESI-MS is able to reveal the detailed chemical structures of various sequences despite the molecular weight limit of 2000 Da. Combination of ESI-MS with NMR can thus provide information to describe microstructure changes during degradation. The distribution of various oligomers shown in the form of planar projections is of great interest for the design of biodegradable system aimed at medical applications.     

Patterning of biomolecules on a poly(-caprolactone) film surface functionalized by ion implantation

Biomolecule patterning is important due to its potential applications in biodevices, tissue engineering, and drug delivery. In this study, we developed a new method for a biomolecular patterning on poly(-caprolactone) (PCL) films based on ion implantation. Ion implantation on a PCL film surface resulted in the formation of carboxylic acid groups. The generated carboxylic acid groups were used for the covalent immobilization of amine-functionalized p-DNA, followed by hybridization with fluorescently tagged c-DNA. Biotin-amine was also covalently immobilized on the carboxylic acid generated PCL surfaces. Successful biotin-specific binding of streptavidin further confirmed the potential of this strategy for patterning of various biomolecules.     

Pyrolysis of polyphenylenes with PCL or/and PSt side chains

Thermal degradation characteristic of polyphenylenes is an important issue for developing a rational technology of polymer processing and applications. In this study, we discussed thermal degradation of polyphenylenes (PP) with poly(-caprolactone) (PCL) and/or PCL/polystyrene copolymers (PSt) prepared by combined controlled polymerization and cross-coupling processes via direct pyrolysis mass spectrometry. When PP-graft-PCL/PSt copolymers were considered, thermally less stabile PCL side chains decomposed in the first step. In the second stage of pyrolysis, the decomposition of the polystyrene chains has taken place. A slight increase in thermal stability of PCL chains for PP-graft-PCL/PSt copolymers was noted compared to copolymer PP-graft-PCL due to the interaction between PSt and PCL chains. This interaction was stronger when PSt chains were linked to the 2-position of the 1,4-phenylene ring.     

Pyrolysis of poly(phenylene vinylene)s with polycaprolactone side chains

The thermal degradation characteristics of a new macromonomer poly(-caprolactone) with central 4,4′-dicarbaldehyde terphenyl moieties and poly(phenylene vinylene)s with well defined (-caprolactone), (PPV/PCL) as lateral substituents were investigated via direct pyrolysis mass spectrometry. The unexpectedly high thermal stability of the macromonomer was attributed to intermolecular acetylation of benzaldehyde yielding a hemiacetal and causing a crosslinked structure during the pyrolysis. Increased thermal stability of the PCL chains was detected for all samples. The increase in stability of PCL chains was much more pronounced than was detected for poly(p-phenylene)-graft-poly(-caprolactone) copolymer (PPP/PCL); the upward temperature shift was about 100 °C for PPV/PCL and only 20 °C for PPP/CL. This pronounced effect may be due to higher thermal stability of PPV compared to PPP and the decrease in steric hindrance for PPV with PCL side chains.     

Phase controllable synthesis of unusual -Ga2O3 single crystals with promising luminescence property

A new synthetic approach to unusual -Ga₂O₃ with improved luminescence properties was developed by taking advantage of a microwave-assisted synthesis followed by calcinations at appropriate temperatures. Upon control of crystallinities of GaOOH precursors and the followed calcination temperature, the single crystalline -Ga₂O₃ nanorods can be synthesized in a large scale. The resulting products were characterized by transmission electron microscopy, powder X-ray diffraction, and cathodoluminescence. The luminescence property of this unusual Ga₂O₃ phase was investigated for the first time.     

The use of synchrotron X-ray scattering coupled with in situ mechanical testing for studying deformation and structural change in isotactic polypropylene

The mechanical behaviour of semi-crystalline polymers is greatly influenced by the properties of the crystalline and the amorphous phases. As a result this topic has been the subject of extensive research. However, to date, a comprehensive relationship between the structure and mechanical properties for semi-crystalline polymers has yet to be established. This present study concerns the commissioning of a novel method for in situ data collection during the deformation of polymers. This involves the combination of three different techniques into a single experiment, namely tensile testing, synchrotron radiation wide angle X-ray scattering, and optical microscopy. For this current investigation, three isotactic polypropylene samples have been studied, produced using different thermal treatments. This enables the influence of thermal treatment on the mechanical properties and crystallographic structure to be assessed. The results indicate that tensile properties are influenced by thermal treatment via the relative fraction of -phase material in the sample. As the temperature increases at which thermal treatment takes place, iPP ductility decreases due to the greater rigidity of the increasing -phase content. Differences in crystal strain between the different iPP crystal phases are also observed although the reasons for such differences remain unclear.     

Distribution of Sorbitan Monooleate in poly(l-lactide-co--caprolactone) nanofibers from emulsion electrospinning

The aim of this study was to investigate the distribution of Sorbitan Monooleate (Span80) in poly(l-lactide-co--caprolactone) (PLLACL) nanofibers from emulsion electrospinning. The hypothesis was that PLLACL/Span80 nanofibrous mats would have some Span80 on the surface of the composite nanofibers. To test the hypothesis, the electrospinning of emulsions made of PLLACL, chloroform, Span80, and distilled water to prepare PLLACL/Span80 nanofibers was systematically investigated. The morphology of PLLACL/Span80 nanofibers was investigated by atomic force microscopy. The surface hydrophilicity of the nanofibrous mats were examined by water contact angle test. The distribution of Span80 on the surface of nanofibrous mats was also confirmed by the performance of pig iliac endothelium cells on the nanofibrous mats.     

Properties and biodegradability of water-resistant soy protein/poly(?-caprolactone)/toluene-2,4-diisocyanate composites

Water-resistant composite plastics were prepared from soy protein isolate (SPI) or soy dreg (SD), poly(?-caprolactone) (PCL) and toluene-2,4-diisocyanate (TDI) as the compatibilizer by blending and one-step reactive extrusion (REX) followed by compression-molding. The structure and properties of the materials (SPI series and SD series) were investigated by Fourier transform infrared spectroscopy, scanning electron microscopy, differential scanning calorimetry, dynamic mechanical thermal analysis and tensile testing. The results indicated that SPI and SD series exhibited high water resistance and good tensile strength (14.8 MPa for SPI35 and 16.3 MPa for SD35). Moreover, the SD series sheets containing cellulose possessed higher tensile strength than those of SPI series when SD content was 30-35%, whereas the latter had a better biodegradability and water resistance. By burying the two series of sheets in soil and culturing them in a mineral salt medium containing microorganisms, both of them were almost completely degraded. This paper provides a convenient way to prepare new soy protein plastics with good biodegradability and water resistivity.     

Preparation and characterization of corn starch/soy protein biocomposite film reinforced with graphene and graphene oxide nanoplatelets

Corn starch (CS) and soy protein isolate (SPI), as inexpensive, abundant, and biodegradable materials, can chemically interact well with each other to produce biofilms. However, to overcome some of their physical and mechanical limitations, it is preferred to use their composite form, employing reinforcing materials. In this study, initially, graphene (G) and graphene oxide (GO) were synthesized by a green method. Then, to enhance the polymer blend final properties, the effects of adding G and GO in the range of 0.5 to 2 wt% on physical and mechanical properties of starch/protein blend were investigated. The results showed that the presence of 0.5‐wt% G and 2‐wt% GO significantly increased the modulus of starch/protein film from 252 to 578 and 449 MPa, respectively. In addition, the thermal stability of CS/SPI/GO (2 wt%) composite film was 50°C to 60°C more than that of the pure starch/protein film. On the other hand, G‐reinforced composite films tended to decline water diffusion compared with the pure polymer film. In addition, the composite film with 2‐wt% GO content had the lowest oxygen permeation rate (3.48 cm³ μm/m²d kpa) among the other composite films.     

Effects of dipole interaction and solvation on the CO stretching band of N,N-dimethylacetamide in nonpolar solutions: Infrared, isotropic and anisotropic Raman measurements

The concentration dependence of the CO stretching (ν_CO) band of N,N-dimethylacetamide (NdMA) in cyclohexane, n-hexane, and CCl₄ has been investigated by infrared (IR) and polarized Raman spectroscopy. For the neat liquid of NdMA, the noncoincidence of the aniso- and isotropic Raman wavenumbers is evident. In the 0.47 M cyclohexane solution of NdMA, the noncoincidence effect almost disappears and the ν_CO envelopes in both the Raman and IR spectra are asymmetric to the low-wavenumber side. When the concentration of NdMA decreases from 0.33 to 0.023 M, the peak of these bands slightly shifts to a higher wavenumber and the band shape becomes symmetric. The shape of the ν_CO envelope does not show any significant change below 0.023 M. These results suggest that the asymmetric shape of the ν_CO band observed for the 0.33 M cyclohexane solution is associated with the intermolecular interaction among NdMA molecules, which vanishes at around 0.02 M. Spectral changes for the CCl₄ solution of NdMA show a similar tendency. However, the shape and peak wavenumber of the ν_CO band observed in a highly diluted CCl₄ solution (≤0.023 M) indicate that the solvation effect of CCl₄ is more complicated than those of cyclohexane and n-hexane. The analyses of the ν_CO band, which is sensitive to the intermolecular interaction between solutes and between solute and solvent for NdMA dissolved in nonpolar solvents, would serve to clarify the electronic property of the molecule in a solution.     

Infrared diode laser spectroscopy of the ν = 2 band of AlF

A vibrational–rotational spectrum of the ν = 2 transitions of a high-temperature molecule AlF was observed between 1490 and 1586 cm⁻¹ with a diode laser spectrometer. Measurements were made on the ν = 3–1, 4–2, 5–3 and 8–6 bands at a temperature of 900 °C. Measured spectral lines were fitted to effective band constants ν₀, B_ν and D_ν for each band. Present measurements were made with only one Pb-salt laser diode. Physical significance of the effective band constants is discussed.     

GC-MS Analysis of the Essential Oil from the Oleoresin of Pistacia atlantica var. mutica

The oleoresin of Pistacia atlantica var. mutica, growing in different regions of Iran, is a popular naturally occurring chewing gum and has been used traditionally in the treatment of peptic ulcer. The GC-MS analysis of the essential oil, obtained from steam distillation of the oleoresin of P. Atlantica var. mutica, has led to the identification and quantification of eleven terpenoids, -pinene (70%), -pinene (1.94%), 3-carene (0.2%), carveol (2.18%), epoxypinene (2.15%), limonene oxide (9%), myrtenol (5.31%), limonene (0.62%), citral (5.72%), -phellandrene (0.2%), and -myrcene (0.3%). The total amount of essential oil obtained was 22% v/w which is higher than any other species of the genus Pestacia.     

Orthogonally Protected,Carboxy-Activated <Emphasis Type="Italic">L</Emphasis>-Homoisoserine, 2-Methyl-<Emphasis Type="Italic">L</Emphasis>-homoisoserine,and Homoisocysteine Derivatives. New Building Blocks for Peptide and Depsipeptide Modification

Summary. Starting from L-malic, L-citramalic, and rac. thiomalic acids routes to L-homoisoserine, 2-methyl-L-homoisoserine and rac. homoisocysteine have been developed. The new orthogonally protected and carboxy-activated building blocks are GABA as well as -hydroxy and -mercapto acid derivatives, suitable for the construction of peptide and depsipeptide surrogates.     

peri-Naphthylenediamines. 37. Synthesis of N,N"-diisopropyl-N,N"-dimethyl-1,8-diaminonaphthalene

Alkylation of N,N"-dimethyl-1,8-diaminonaphthalene with 2-iodopropane in a KOH—DMSO system afforded a new proton sponge, viz., N,N"-diisopropyl-N,N"-dimethyl-1,8-diaminonaphthalene; the rotation barrier of the Prⁱ groups about the N—C bond is 68.4±0.4 kJ mol^–1 (DMSO).     

Soy Protein Isolate Based Films: Influence of Sodium Dodecyl Sulfate and Polycaprolactone-triol on Their Properties

Summary: We report on the preparation and properties of soy protein isolate (SPI)-sodium dodecyl sulfate (SDS)-polycaprolactone-triol (PCL-T) films obtained by solvent casting from solutions containing variable amounts of SDS or SDS/PCL-T. It is shown that the mechanical and thermal properties, and the morphology of SPI-based biofilms can be easily controlled by changing SDS, PCL-T, and moisture contents, enabling the fabrication of rigid and flexible materials as pure SPI films [Young's modulus ∼ 1 400 MPa, elongation at break (E) ∼ 2%, and glass transition temperature (T_g) ∼ 150 °C] and SPI/SDS/PCL-T films with [PCL-T] ≥ 18% (Young's modulus ∼ 50 MPa, E ∼ 90%, and T_g ∼ 135 °C), respectively. Micrographs taken at the cross-section of biofilms whose [PCL-T] ≥ 18% revealed the occurrence of a porous matrix, whereas a dense bulk phase was otherwise observed (pure SPI, SPI/SDS, and SPI/SDS/PCL-T films with [PCL-T] < 18%).     

(E)-1,2-Difluoro-1-iodo-2-trialkylsilanes—A useful synthon for the addition of the [IFCCF] unit to activated electrophiles

Fluoride ion catalyzed reaction of (E)-IFCCFSiR₃ with activated aromatic aldehydes and ketones and activated perfluoroaromatics, such as pentafluoropyridine and perfluorotoluenes, transfers the [IFCCF] unit to the activated electrophiles to stereospecifically provide (E)-1,2-difluoro-1-iodosubstituted derivatives. Aluminum chloride catalyzed reaction of (E)-1,2-difluoro-1-iodo-2-trialkylsilanes with alkyl or aryl acyl halides gives the corresponding (E)-1,2-difluoro-1-iodoketones stereospecifically in excellent yield. The vinyl iodide product formed via this methodology could be coupled (with Pd(0)) catalysis to provide an entry to a polyfunctionalized derivative.     

Substituted 1,2-Thiazetidine 1,1-Dioxides. Synthesis of (<Emphasis Type="Italic">RS</Emphasis>)- and (<Emphasis Type="Italic">S</Emphasis>)-1,2-Thiazetidine-3-acetic Acid 1,1-Dioxide and its Reactions with Amino Acids and Dipeptides

Summary. (RS)-2-tert-Butyldimethylsilyl-1,2-thiazetidine-3-acetic acid 1,1-dioxide prepared from (RS)-S-benzyl--homocysteine was condensed via DCC/NHS with various L-amino acid esters or dipeptide esters yielding N-silylated -sultam peptides. A -sultam active ester was isolated as an intermediate. Desilylation with TBAF in THF yielded stable N-unsubstituted products, and deprotection of the benzyl esters was achieved by catalytic hydrogenation. (S)-S-Benzyl--homocysteine was obtained by fractional crystallization of the brucine salt of the racemate and transformed into benzyl (S)-1,2-thiazetidine-3-acetate, which was on the other hand synthesized by an enantiospecific route from -benzyl Boc-L-aspartate. Some -sultam peptides were prepared from the (S)-enantiomer, and finally some -sultam peptides containing D-Ala units were obtained.