Matrix Solid-Phase Dispersion Extraction and UPLC Determination of Sudan Dyes in Chili Powder

A new method involving matrix solid-phase dispersion (MSPD) extraction and UPLC in conjunction with photodiode array detection was developed for the rapid and simple determination of Sudan dyes in chili powder. Separation of Sudan I, Sudan II, Sudan III, and Sudan IV was achieved within 2 min on the 1.7 μm Acquity UPLC BEH C18 column by using gradient elution with a mobile phase consisting of acetonitrile–water at a flow rate of 0.5 mL min^?1. Optimization of MSPD extraction parameters, such as type of solid sorbent and elution solvent were carried out. Optimal conditions selected for MSPD extraction were 0.25 g of sample, 0.5 g of silica gel as solid sorbent, and 7 mL of acetonitrile–methanol (9:1, v/v) as eluting solvent. Limits of detection ranged between 0.25 and 0.30 mg kg^?1 depending on the dye involved. All analytes provided average recoveries from spiked (at 1, 1.5, and 2 mg kg^?1) chili powder samples ranging from 81 to 106%. The method was applied to the analysis of chili powder samples obtained from different countries.     

Analysis of Para Red and Sudan Dyes in Egg Yolk by UPLC–MS–MS

Matrix solid-phase dispersion (MSPD) with alumina N as adsorbent has been used for extraction of para red, Sudan 1, Sudan 2, Sudan 3, and Sudan 4 dyes from egg yolk. The extracts were analyzed by ultra-performance liquid chromatography–tandem mass spectrometry (UPLC–MS–MS). Mean recovery for the five dyes ranged from 63.2 to 98.6%, with CV 0.55–10.00%. One sample was confirmed to contain 0.3 mg kg^?1 Sudan 4.     

A multi-residue method for pesticide residue analysis in rice grains using matrix solid-phase dispersion extraction and high-performance liquid chromatography–diode array detection

Pesticides are widely used in rice cultivation, often resulting in detection of their residues in rice grains. So far, no analytical method has been available for the simultaneous determination of most rice pesticides in rice grains. This paper reports the development and validation of such a method for the determination of eight rice pesticides (penoxsulam tricyclazole, propanil, azoxystrobin, molinate, profoxydim, cyhalofop-butyl, deltamethrin) and 3,4-dichloroaniline, the main metabolite of propanil. Pesticide extraction and clean-up was performed by an optimized matrix solid-phase dispersion (MSPD) protocol on neutral alumina (5 g) using acetonitrile as the elution solvent. Samples were analyzed in a high-performance liquid chromatography–diode array detection (HPLC-DAD) system. Pesticide separation was achieved with a mobile phase of acetonitrile/water in a linear elution gradient from 30:70% (v/v) to 100:0% (v/v) in 14 min at a flow rate of 0.8 mL min^?1. Method validation was performed by means of linearity, intra-day accuracy, inter-day precision and sensitivity. Linear regression coefficients (R ²) were always above 0.9948. Limits of detection (LOD) and quantification (LOQ) varied from 0.002 to 0.200 mg kg^?1 and 0.006 to 0.600 mg kg^?1, respectively. Recoveries were investigated at three fortification levels and were found to be acceptable (74–127%) with relative standard deviations (RSD) below 12%. Application of the method for the analysis of five commercial rice grain samples showed that the pesticide levels were below the LOD. Overall, the method developed is suitable for the determination of residues of most rice pesticides in rice grains at levels below the established MRLs.     

Fast Determination of Sudan I-IV in Chili Products Using Automated On-Line Solid Phase Extraction Coupled with Liquid Chromatography-Mass Spectrometry

A rapid, accurate and precise method for the determination of sudan I-IV in chili products using on-line solid phase extraction and LC-MS has been developed. Chili products were extracted with acetone and the analytes were cleaned up and enriched on an SPE column (C₁₈, 15–40 µm) through on-line SPE. Chromatographic separation was performed on a C₁₈ analytical column (2.1 × 150 mm, 3 µm) with gradient elution programming of 0.1% formic acid in water and 0.1% formic acid in acetonitrile. All four sudan dyes were separated in less than 8 min. Using in-house validation data, linearity coefficients of determination (R²) of more than 0.9997 were obtained. The limits of detection (LOD) and limits of quantitation (LOQ) for sudan I, II and IV were 0.03 and 0.05 mg kg^?1, respectively, and 0.04 and 0.1 mg kg^?1 for sudan III. The intra- and inter-day recoveries of the four sudan dyes in chili powder were between 90.1–101.6% and 90.2–102.0%, respectively, with relative standard deviation (RSD) between 0.014–0.164% and 0.011–0.202%, respectively. Therefore, this proposed method could be an alternative assay for the determination of sudan I-IV in chili products due to its rapidness, sensitivity, less sample and solvent consumption.     

Rapid monitoring of carvacrol in plants and herbal medicines using matrix solid-phase dispersion and gas chromatography flame ionisation detector

Matrix solid-phase dispersion (MSPD) method coupled with gas chromatography flame ionisation detector as a quick and easy extraction technique has been developed to extract carvacrol from plants and herbal medicines. Influence of important parameters on the MSPD method efficiency, such as the sorbent material, the ratio of sample to sorbent material, elution solvent and volume of the elution solvent has been evaluated and optimised. Carvacrol was successfully extracted by diatomaceous earth as sorbent with 350 μL of dichloromethane as elution solvent. The calibration curve showed good linearity (r² = 0.9965) and precision (RSD < 8.16%) in the concentration range of 0.5–100 μg mL^? 1 for carvacrol. The limit of detection and limit of quantification were 0.1 and 0.5 μg mL^? 1, respectively. The recoveries were in the range of 74.4–80.5% with relative standard deviation (RSD) values ranging from 8.4% to 9.8%. The reported MSPD extraction method revealed to be simpler and faster than conventional methods used to quantify carvacrol from plants and herbal medicines.     

LC Method for Determination of Ginkgolic Acids in Mice Plasma and Its Application to a Pharmacokinetic Study

A sensitive and simple LC method for the quantification of ginkgolic acids in mice plasma has been developed. Following acetonitrile deproteinization, samples were separated on a SinoChrom ODS-AP C₁₈ column. The mobile phase was 3% (v/v) acetic acid water solution–methanol (8:92, v/v) at a flow rate of 1.0 mL min⁻¹. Detection was at 310 nm. Calibration curve was linear over the range of 0.25–50 μg mL⁻¹ with intra- and inter-day precisions (RSD%) of less than 9.5%. The extraction recovery ranged from 87.0 to 90.2% (RSD 2.4–6.4%) for ginkgolic acids. The method was successfully applied to the pharmacokinetic study of ginkgolic acids in mice after oral dosing of 1.0 g kg⁻¹.

     

An On-line Admicellar SPE-HPLC System Using CTAB-Modified Zeolite NaY as Sorbent for Determination of Carbamate Pesticides in Water

Zeolite NaY modified with cetyltrimethylammonium bromide (CTAB) was considered for extraction/preconcentration of carbamate pesticides using an on-line SPE-HPLC system. The simultaneous determination of carbamate pesticides, including aldicarb, carbofuran, carbaryl, isoprocarb, methiocarb and promecarb, was performed by HPLC–UV using a LichroCART RP-18 column with gradient elution of methanol and 0.1 % acetic acid. The sorbent presented admicelles of CTAB on its surfaces and exhibited a sorption capacity of 180–18,600 mg kg⁻¹ sorbent, which could be re-modified for at least five extraction cycles. The quantitative retention of target pesticides on the admicellar sorbent involved hydrophobic and π-cation interaction, while pesticides were eluted from the admicellar SPE column using only 750 μL of methanol. LODs and LOQs of the proposed method were 0.005–140 and 0.02–600 μg L⁻¹, respectively. The analytes were effectively concentrated with the enrichment factors between 5 and 551. The developed on-line admicellar SPE-HPLC system was successfully applied to the determination of carbamate pesticides in ten environmental water samples from different sources. Recoveries of spiked samples at a concentration of 0.1–5 mg L⁻¹ ranged from 77 to 111 %.

     

Simultaneous Determination of Zoalene and Its Metabolite in Chicken Muscle and Liver by SPE and UPLC–MS-MS

This paper presents an analytical method for the simultaneous determination of zoalene and its metabolite 3-amino-5-nitro-o-toluamide (3-ANOT) in chicken muscle and liver by solid phase extraction and UPLC–MS-MS operated in the positive and negative ionization switching mode. Samples were extracted with phosphate buffer solution and purified with OASIS^™ HLB cartridge after pH adjustment. The determination was carried out using UPLC–MS-MS on a Waters Acquity BEH C₁₈ column with 0.1% formic acid in water/acetonitrile as mobile phase with gradient elution. The linearity of the analytical response across the studied range of concentrations (2.0–1,000 μg L⁻¹) was excellent, obtaining correlation coefficients higher than 0.999. Matrix effects had been investigated for zoalene and 3-ANOT. Recovery studies were carried out on spiked chicken muscle and liver blank samples, at four concentration levels (50, 1,500, 3,000, and 4,500 μg kg⁻¹ for chicken muscle and 50, 3,000, 6,000, and 9,000 μg kg⁻¹ for chicken liver) performing six replicates at each level. Mean recoveries of 77.9–94.2% with CVs of 3.2–8.7% were obtained. The method demonstrated to be suitable for the simultaneous determination of zoalene and 3-ANOT in chicken tissues.

     

Determination of Cypermethrin Residues in Crucian Carp Tissues by MSPD/GC-ECD

A sensitive matrix solid-phase dispersion (MSPD)/gas chromatography-electron capture detector (GC-ECD) method was developed to determine cypermethrin residues in three tissues (muscle, liver, and gill) of crucian carp. Cypermethrin was simultaneously extracted by MSPD and determined by GC-ECD. The main parameters affecting extraction yield and selectivity, such as the type of solid adsorbent material, choice of elution solvents and their volume, were investigated to obtain interference-free extracts and quantitative cypermethrin recovery. Fortified recoveries in muscle, liver, and gill samples ranged from 84.9% to 106.1%, and relative standard deviations were <8% with fortification levels of 0.05–1 mg kg^?1. Detection limits were 1.4–2.1 μg kg^?1, and quantitation limits were 5.8–7.8 μg kg^?1. The proposed method was successfully applied to determination of cypermethrin in fish tissue samples.     

Improving the Determination of Nitrovin in Feeds by Reversed-Phase LC with SPE

A simple reversed-phase liquid chromatographic method with ultraviolet detector (378 nm) for the determination of nitrovin in feeds was improved and validated. The mobile phase was a mixture of acetonitrile and 0.1% formic acid solution (v/v) in the ratio of 50:50 (v/v), and the flow rate was set at 1.2 mL min^?1. The extraction solution was a mixture of dimethyl formamide, acetonitrile and methanol (50:25:25, v/v), the sample was cleaned-up with reversed-phase solid phase extraction cartridge. The standard nitrovin was purified with crude nitrovin product by ethylene glycol monoethyl ether and identified by elemental analyzer. The limit of detection was 0.05 mg kg^?1 and the limit of quatification was 0.2 mg kg^?1 in feeds. The assay had satisfactory selectivity, recovery, linearity and precise repeatability and trueness.     

Quantitative Determination of Allicin in Allium sativum L. Bulbs by UPLC

An UPLC method for determination of allicin in garlic bulb powder has been developed and validated. Chromatographic separation and determination were performed on an Acquity UPLC BEH C₁₈ column using a mobile phase of methanol/water (50:50, v/v). Linearity between the allicin concentration and the peak area was good within the concentration ranges 2.04–510 mg L⁻¹. The method was validated over this range for both accuracy and precision. The method was successfully used for the quantitative analysis of allicin in ten garlic varieties.

     

MSPD procedure for determining buprofezin,tetradifon, vinclozolin,and bifenthrin residues in propolis by gas chromatography–mass spectrometry

A simple and effective extraction method based on matrix solid-phase dispersion (MSPD) was developed to determine bifenthrin, buprofezin, tetradifon, and vinclozolin in propolis using gas chromatography–mass spectrometry in selected ion monitoring mode (GC–MS, SIM). Different method conditions were evaluated, for example type of solid phase (C₁₈, alumina, silica, and Florisil), the amount of solid phase and eluent (n-hexane, dichloromethane, dichloromethane–n-hexane (8:2 and 1:1, v/v) and dichloromethane–ethyl acetate (9:1, 8:2 and 7:3, v/v)). The best results were obtained using 0.5 g propolis, 1.0 g silica as dispersant sorbent, 1.0 g Florisil as clean-up sorbent, and dichloromethane–ethyl acetate (9:1, v/v) as eluting solvent. The method was validated by analysis of propolis samples fortified at different concentration levels (0.25 to 1.0 mg kg⁻¹). Average recoveries (four replicates) ranged from 67% to 175% with relative standard deviation between 5.6% and 12.1%. Detection and quantification limits ranged from 0.05 to 0.10 mg kg⁻¹ and 0.15 to 0.25 mg kg⁻¹ propolis, respectively.     

Extraction and Determination of β-Sitosterol from Salicornia herbacea L. Using Monolithic Cartridge

A short ionic liquids-based monolithic cartridge was prepared and used as the selective extraction sorbent. Characteristic and evaluation are investigated by field emission scanning electron microscopy (FE-SEM), and a new approach was developed for the extraction and determination of β-sitosterol from Salicornia herbacea L. using the ionic liquids-based monolithic cartridge. Chromatographic analysis was conducted on a C₁₈ column with UV detection at 210 nm, and an eluting solution consisting of acetonitrile–water (60/40, v/v) was used as the mobile phase at a flow rate of 0.8 mL min⁻¹. The linearity was confirmed in the concentration range of 0.50–100.00 μg mL⁻¹, with RSDs within 4.20%, and a recovery of β-sitosterol ranging from 97.20 to 102.93%. This method effectively removed the impurities without any tedious pretreatment, and it provided a fast, economic and effective way to assay trace drugs from natural plants.

     

Analysis of trans-Resveratrol in Iranian Grape Cultivars by LC

In this study, trans-resveratrol levels were determined in 147 Iranian grape cultivars using a modified extraction and gradient HPLC procedure with photodiode array detection. It was found that 41 out of 147 cultivars contained significant levels of trans-resveratrol. The detected amounts ranged from 0.98 to 6.25 mg kg⁻¹ fresh weight with a mean value of 3.59 (white grapes) and 3.08 mg kg⁻¹ (red grapes), respectively.

     

MSPD Procedure for Determination of Carbofuran, Pyrimethanil and Tetraconazole Residues in Banana by GC–MS

An extraction method based on matrix solid-phase dispersion was developed to determine carbofuran, pyrimethanil and tetraconazole in banana using gas chromatography–mass spectrometry. The best results were obtained using 2.0 g of banana, 1.0 g of silica as dispersant sorbent and n-hexane:ethyl acetate (1:4, v/v) as eluting solvent. The method was validated using banana samples fortified with pesticides at different concentration levels (0.05–2.0 mg kg^?1). Average recoveries (four replicates) ranged from 68 to 111%, with relative standard deviations between 6.6 and 20.5%. Detection and quantification limits for banana ranged from 0.02 to 0.05 and 0.05 to 0.10 mg kg^?1, respectively.     

Matrix Solid-Phase Dispersion Extraction for Analysis of Cypermethrin Residue in Cows’ Milk

A method of extraction based on matrix solid-phase dispersion has been developed, optimized, and validated by chromatographic analysis of cypermethrin pesticide residues in samples of cows’ milk. Milk (0.25 g) was fortified with cypermethrin and blended with 1 g each of C₁₈ (octadecylsilane) silica and Na₂SO₄ (anhydrous sodium sulfate), used to trap fats and water, respectively. The homogenized material was transferred to a commercial SPE cartridge containing 1 g activated Florisil with 5 mL acetonitrile. Cypermethrin was eluted under vacuum with 5 × 2 mL acetonitrile and the extract was concentrated to 1 mL and analyzed by gas chromatography–mass spectrometry. The limits of detection and quantification of the method were 0.025 and 0.08 mg kg⁻¹, respectively.

     

Simultaneous Determination of Carbamazepine and its Active Metabolite Carbamazepine-10,11-epoxide in Human Plasma by UPLC

A simple method for the determination of carbamazepine and its active metabolite carbamazepine-10,11-epoxide by ultra performance liquid chromatography (UPLC) with ultraviolet absorbance detection (TUV) was developed. The method involves a two-step protein precipitation by liquid–liquid extraction. Phenytoin sodium was used as the internal standard. The separation was carried out on Acquity C18 column with acetonitrile:methanol:KH₂PO₄ buffer (adjusting pH to 4.6 with 85% o-phosphoric acid) (180/180/170, v/v/v) as the mobile phase at a flow rate of 0.4 mL min⁻¹. Linear detection response was obtained for concentrations ranging from 50 to 5,000 ng mL⁻¹. The limit of quantification (LOQ) was 50 ng mL⁻¹. The method was validated successfully for the determination of carbamazepine and its active metabolite carbamazepine-10,11-epoxide, which can be applied through pharmacokinetics and bioequivalence studies.

     

Focused Microwave-Assisted Extraction and LC Determination of Ketoprofen in the Presence of Preservatives in a Pharmaceutical Cream Formulation

A simple and rapid open-vessel focused microwave-assisted extraction (FMAE) method followed by LC analysis was developed for the determination of ketoprofen lysine salt in the presence of methyl p-hydroxybenzoate and propyl p-hydroxybenzoate preservatives in topical cream. Extraction were performed in acetone/potassium dihydrogenphosphate (25 mM, pH 3.0) (70:30 v/v) by reaching a target temperature of 65 °C in a 10 min linear ramp. The chromatographic separation was performed on a Discovery RP-Amide C16 column (250 × 4.6 mm I.D., 5 μm particle size). The optimal mobile phase consisted of acetonitrile/potassium dihydrogen phosphate 25 mM adjusted to pH 3.0 with phosphoric acid (50:50 v/v). The complete analytical procedure was validated with regard to limit of quantification, linearity, precision and accuracy. The method was linear over the concentration range of 0.08–0.12 mg mL⁻¹; the relative standard deviations of intra- and inter-day assays were 1.9–2.3 and 1.8% respectively. The limit of quantification was 0.54 μg mL⁻¹. The proposed method shows many advantages as short extraction time, little solvent consumption without requiring further sample clean-up steps before liquid chromatographic analysis and is proposed for vast scale screening of cream dosage forms aimed to the detection of counterfeit and substandard drugs.

     

Biodegradation of imidacloprid in sandy loam soil by Bacillus aerophilus

A study of the biodegradation of imidacloprid in soil was carried out under laboratory conditions. Sandy soil samples were fortified with imidacloprid at 50, 100 and 150 mg kg^?1 along with 45 x 10⁷ colony forming units (cfus) of Bacillus aerophilus and the samples were compared with unamended soil. The samples were extracted with acetonitrile, cleaned up by treatment with primary secondary amine sorbent and graphitised carbon black. The residues of imidacloprid and its metabolites were analysed by high performance liquid chromatography. The parent compound, imidacloprid, was found to be more persistent in both the treatments. Among metabolites, the highest values were obtained for urea and olefin while 5-hydroxy, 6-chloronicotinic acid (6-CNA), nitrosimine and nitroguanidine (NTG) were also observed in all the treatments in amended soil. In case of unamended (control) soil, 6-CNA was found to be the most persistent metabolite followed by olefin, urea, 5-hydroxy, nitrosimine and NTG metabolites. Total imidacloprid residues for control soil samples followed first-order kinetics at 50 and 150 mg kg^?1 but in case of control imidacloprid fortified at 100 mg kg^?1, the total residues of imidacloprid and its metabolites followed pseudo-first-order kinetics. The respective half-life value for 50 mg kg^?1 was 25.08 days and 30.10 days for both 100 and 150 mg kg^?1. However, total imidacloprid residues followed pseudo-first-order kinetics for its applications at 50, 100 and 150 mg kg^?1 in sandy loam soil amended with B. aerophilus. The half-life values for 50, 100 and 150 mg kg^?1 were worked out to be 14.33, 15.05 and 18.81 days, respectively. With the use of B. aerophilus, the reduction percentage of initial applied dose imidacloprid in sandy loam soil was found to be higher in all the three doses as compared to that of the control samples.     

Identification of Acepromazine and Its Metabolites in Horse Plasma and Urine by LC–MS/MS and Accurate Mass Measurement

Acepromazine maleate (Sedalin^®) was administered orally to six thoroughbred horses at a dose of 0.15 mg kg⁻¹. Urine and blood samples were collected up to 412 h post-administration. Plasma and urine were hydrolysed; plasma samples were then processed using liquid–liquid extraction and urine samples using solid-phase extraction. A sensitive tandem mass spectrometric method was developed in this study, achieving a lower limit of quantification for acepromazine of 10 pg mL⁻¹ in plasma and 100 pg mL⁻¹ in urine. Acepromazine, hydroxyethylpromazine, hydroxyacepromazine, hydroxyethylpromazine sulphoxide, hydroxyethylhydroxypromazine, dihydroxyacepromazine and dihydroxyhydroxyethylpromazine were detected in the post-administration samples. The parent drug and its metabolites were identified using a combination of UPLC–MS/MS and accurate mass measurement. Separation of the structural isomers hydroxyethylpromazine sulphoxide and hydroxyethylhydroxypromazine was another significant outcome of this work and demonstrated the advantages to be gained from investing in chromatographic method development.