Effect of catalysts on dc corona discharge poisoning

The processes of ozone generation in non-thermal plasma produced by an electrical discharge in air at atmospheric pressure are burdened by the presence of nitrogen oxides, which on the one hand contribute to ozone generation and on the other hand are responsible for unpleasant discharge poisoning. The term discharge poisoning refers to the situation when the discharge ozone formation completely breaks down. Discharge poisoning can be affected by placing a catalyst in the discharge chamber. For the dc hollow needle to mesh corona discharge enhanced by the flow of air through the needle electrode we studied the effect of titanium dioxide TiO₂, ZSM-5 zeolite or Cu⁺⁺ZSM-5 zeolite on discharge poisoning by monitoring the ozone, nitrogen monoxide and nitrogen dioxide discharge production. We found that placing globules of any of these catalysts on the mesh decreases the energy density of the onset of discharge poisoning, and this energy density is smallest for a discharge with globules of a TiO₂ on the mesh.     

Preparation of N-doped TiO<Subscript>2</Subscript> photocatalyst by atmospheric pressure plasma process for VOCs decomposition under UV and visible light sources

The nitrogen doped (N-doped) titanium dioxide (TiO₂) photocatalyst was prepared by the atmospheric-pressure plasma-enhanced nanoparticles synthesis (APPENS) process operated under normal temperature, i.e. the dielectric barrier discharge plasma process. The N₂ carrier gas is dissociated in the AC powered nonthermal plasma environment and subsequently doped into the TiO₂ photocatalyst that was capable of being induced by visible light sources. The APPENS process for producing N-doped TiO₂ showed a higher film deposition rate in the range of 60–94 nm/min while consuming less power (<100 W) as compared to other plasma processes reported in literatures. And the photocatalytic activity of the N-doped TiO₂ photocatalyst was higher than the commercial ST01 and P25 photocatalysts in terms of toluene removals in a continuous flow reactor. The XPS measurement data indicated that the active N doping states exhibited N 1s binding energies were centered at 400 and 402 eV instead of the TiN binding at 396 eV commonly observed in the literature. The light absorption in the visible light range for N-doped TiO₂ was also confirmed by a clear red shift of the UV-visible spectra.     

Synthesis and nanostructural investigation of TiO<Subscript>2</Subscript> nanorods doped by SiO<Subscript>2</Subscript>

TiO₂ Nano rods can be used as dye-sensitized solar cells, various sensors and photocatalysts. These nanorods are synthesized by a hydrothermal corrosion process in NaOH solution at 200°C using TiO₂ powder as the source material. In the present work, the synthesis of TiO₂ nanorods in anatase, rutile and Ti₇O₁₃ phases and synthesis of TiO₂ nanorods by incorporating SiO₂ dopant, using the sol–gel method and alkaline corrosion are reported. The morphologies and crystal structures of the TiO₂ nanorods are characterized using field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD) study. The obtained results show not only an aggregation structure at high calcination temperatures with spherical particles but also Ti–O–Si bonds having four-fold coordination with oxygen in SiO^4 −.     

Preparation of TiO<Subscript>2</Subscript>-coated LiCo<Subscript>1/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> by electrostatic self-assembly method and its properties

A precursor of TiO₂–LiCo_1/3Ni_1/3Mn_1/3O₂ was prepared by electrostatic self-assembly method. The final product was obtained by heating the precursor at 400–450 °C for 4–6 h in air. X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and electrochemical tests were used to examine the structural, morphology, elementary valence, and electrochemical characteristics. XRD indicated that the TiO₂-coated material can be indexed by α-NaFeO₂ layered structure, which belongs to hexagonal-type space group R3m. XPS results confirmed the existence of TiO₂ compound on the surface of the coated sample. The SEM image showed that the material had spherically porous morphology with the uniform size about 6 μm. The initial charge–discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ material was 168.8/160.0 mAh/g. After 60 cycles, the discharge capacity of the TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ sample was 147.0 mAh/g, and the coulombic efficiency was 94.0%. Compared with the uncoated sample, the electrochemical performance of TiO₂-coated LiCo_1/3Ni_1/3Mn_1/3O₂ was improved.     

Hierarchical structured ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript>@RGO@TiO<Subscript>2</Subscript> composite as powerful visible light catalyst for degradation of fulvic acid

Hierarchical structured ZnFe₂O₄@reduced graphite oxide@TiO₂ (ZnFe₂O₄@RGO@TiO₂) nanocomposite was prepared by an electrostatic layer-by-layer route, which played a synthetic effect of Fenton oxidation of ZnFe₂O₄ and photocatalytic oxidation of TiO₂ to degrade fulvic acid (FA) solution under visible-light irradiation. In this method, RGO, as the middle layer, can effectively promote the photo-induced electron flow between the ZnFe₂O₄ and TiO₂ and further improve the efficiency of the photo-Fenton oxidation. The influencing factors on photo-Fenton oxidation, including solution pH, catalyst, and H₂O₂ dosage, have also been investigated. The results illustrated that the ternary composite presented the enhanced catalytic performance. Under visible light irradiation, the degradation efficiency of the sample on the FA solution can reach 95.4% within 3 h. In addition, the catalyst exhibited superior stability and reusability, and its degradation efficiency was still up to 90% after 5 cycles. Therefore, the composite will be a kind of efficient photocatalyst and had a promising application for visible-light driven destruction of organic pollutants.     

Analysis of TiO2 photocatalysis in a pulsed discharge system for phenol degradation

Photocatalysis of supported TiO₂ film photocatalyst in a pulsed discharge system for phenol degradation was studied in this paper. The obtained results revealed that the supported TiO₂ film with anatase structure had preferable photocatalytic activity in the pulsed discharge system. Phenol degradation and main byproduct generation were better in the discharge/TiO₂ system. The photocatalyst prepared with eight times dipping process had higher photocatalytic activity than other photocatalysts and testified a preferable photocatalyst condition in the pulsed discharge system. Furthermore, the supported TiO₂ photocatalyst kept photocatalytic activity after using five times in the pulsed discharge system.     

Antibacterial effect of silver modified TiO<Subscript>2</Subscript>/PECVD films

This paper deals with photocatalytic activity of silver treated TiO₂ films. The TiO₂ films were deposited on glass substrates by plasma enhanced chemical vapor deposition (PECVD) in a vacuum reactor with radio frequency (RF) low temperature plasma discharge in the mixture of oxygen and titanium isopropoxide vapors (TTIP). The depositions were performed under different deposition conditions. Subsequently, the surface of TiO₂ films was modified by deposition of silver nanoparticles. Photocatalytic activity of both silver modified and unmodified TiO₂ films was determined by decomposition of the model organic matter (acid orange 7). Selected TiO₂ samples were used for tests of antibacterial activity. These tests were performed on Gram-negative bacteria Escherichia coli. The results clearly proved that presence of silver clusters resulted in enhancement of the photocatalytic activity, which was up to four times higher than that for pure TiO₂ films.     

Assembly,characterization, and photocatalytic activities of TiO<Subscript>2</Subscript> nanotubes/CdS quantum dots nanocomposites

The semiconductor quantum dots (QDs) can be very efficient to tune the response of photocatalyst of TiO₂ to visible light. In this study, CdS QDs formed in situ with about 8 nm have been successfully deposited onto the surfaces of TiO₂ nanotubes (TNTs) to form TNTs/CdS QDs nanocomposites by use of a simple bifunctional organic linker, thiolactic acid. The diffuse reflectance spectroscopy (DRS) spectra of as prepared samples showed that the absorption edge of the TNTs/CdS composite is extended to visible range, with absorption edge at 530 nm. The photocatalytic activity and stability of TNTs/CdS were also evaluated for the photodegradation of rhodamine B. The results showed that when TNTs/CdS QDs was used, photocatalytic degradation of RhB under visible light irradiation reached 91.6%, higher than 45.4 and 30.5% for P25 and TNTs, respectively. This study indicated that the TNTs/CdS QDs nanocomposites were superior catalysts for photodegradation under visible light irradiation compared with TNTs and P25 samples, which may find wide application as a powerful photocatalyst in environmental field.     

DC corona discharge ozone production enhanced by magnetic field

We have studied the effect of a stationary magnetic field on the production of ozone from air at atmospheric pressure by a negative corona discharge in a cylindrical electrode configuration. We used a stainless steel hollow needle placed at the axis of the cylindrical discharge chamber as a cathode. The outer wall of the cylinder was used as an anode. The vector of magnetic induction was perpendicular to the vector of current density. We found that: (a) the magnetic field extends the current voltage range of the discharge; (b) for the discharge in the Trichel pulses regime and in the pulseless glow regime, the magnetic field has no substantial effect on the discharge voltage or on the concentration of ozone that is produced; (c) for the discharge in the filamentary streamer regime for a particular current, the magnetic field increases the discharge voltage and consequently an approximately 30% higher ozone concentration can be obtained; (d) the magnetic field does not substantially increase the maximum ozone production yield. A major advantage of using a magnetic field is that the increase in ozone concentration produced by the discharge can be obtained without additional energy requirements.     

Thermostable photocatalytically active TiO<Subscript>2</Subscript> anatase nanoparticles

Anatase is the low-temperature (300–550 °C) crystalline polymorph of TiO₂ and it transforms to rutile upon heating. For applications utilizing the photocatalytic properties of nanoscale anatase at elevated temperatures (over 600 °C) the issue of phase stabilisation is of major interest. In this study, binary TiO₂/SiO₂ particles were synthesized by a flame aerosol process with TiCl₄ and SiCl₄ as precursors. The theoretical Si/Ti ratio was varied in the range of 0.7–1.3 mol/mol. The synthesized TiO₂/SiO₂ samples were heat treated at 900 and 1,000 °C for 3 h to determine the thermostability of anatase. Pyrogenic TiO₂ P25 (from Evonik/Degussa, Germany) widely applied as photocatalyst was used as non-thermostabilized reference material for comparison of photocatalytic activity of powders. Both the non-calcinated and calcinated powders were characterized by means of XRD, TEM and BET. Photocatalytic activity was examined with dichloroacetic acid (DCA) chosen as a model compound. It was found that SiO₂ stabilized the material retarding the collapse of catalyst surface area during calcination. The weighted anatase content of 85% remains completely unchanged even after calcination at 1,000 °C. The presence of SiO₂ layer/bridge as spacer between TiO₂ particles freezes the grain growth: the average crystallite size increased negligibly from 17 to 18 nm even during the calcination at 1,000 °C. Due to the stabilizing effect of SiO₂ the titania nanoparticles calcinated at 900 and 1,000 °C show significant photocatalytic activity. Furthermore, the increase in photocatalytic activity with calcination temperature indicates that the titania surface becomes more accessible either due to intensified cracking of the SiO₂ layer or due to enhanced transport of SiO₂ into the necks thus releasing additional titania surface.     

Ozone generation in oxygen-fed wire-to-cylinder ozonizer: effect of CH2Cl2, CHCl3 and CCl4 diluents

The inhibition effect of methylene chloride CH₂Cl₂, chloroform CHCl₃ and carbon tetrachloride CCl₄ on the ozone generation process from oxygen by negative corona discharge was experimentally investigated. The experiments were performed in a system of coaxial cylindrical electrodes at total gas pressure of 900 mbar and ambient temperature of gaseous mixtures. The rate of ozone generation as well as ozone concentration apparently decreases with a rising number of substituted chlorine atoms in the methane molecule at constant specific energy consumption dissipated in the discharge and at constant concentration of gaseous impurities in oxygen. In addition to experimental results, the paper presents theoretical considerations aimed at identifying the main process responsible for inhibition of ozone generation. The consumption of considerable fraction of oxygen atoms by CH _x Cl _y–1 radicals formed in discharge, is likely the most important mechanism responsible for the deleterious effect of such compounds on the efficiency of ozone production.     

The production of excimer molecules and excited atoms in a positive corona discharge in He/Xe(Kr)/SF6/CCl4 mixtures

Electrical and optical characteristics of a positive corona discharge in He/Xe(Kr)/SF₆/CCl₄ mixtures, which are of interest for the use in multiwavelength excimer radiation sources, are studied in the needle-grid electrode configuration. The length of the discharge, which is usually used to pump repetitive high-pressure multiwavelength radiation sources, is equal to the length of the electrodes of an excimer laser or lamp pumped by a transverse electric discharge. The discharge current-voltage and frequency characteristics, panoramic emission spectra, and the dependences of the relative emission intensity from the halogenides and excited noble gas atoms on the corona discharge current are investigated. The main processes resulting in the production of halogenides, as well as xenon and krypton excited atoms, in the generation regions of a corona discharge are studied.     

Nanocrystalline Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> electrodes for supercapattery application

Nanocrystalline Li₂TiO₃ was successfully synthesized using solid-state reaction method. The microstructural and electrochemical properties of the prepared material are systematically characterized. The X-ray diffraction pattern of the prepared material exhibits predominant (002) orientation related to the monoclinic structure with C2/c space group. HRTEM images and SAED analysis reveal the well-developed nanostructured particles with average size of ～40 nm. The electrochemical properties of the prepared sample are carried out using cyclic voltammetry (CV) and chronopotentiometry (CP) using Pt//Li₂TiO₃ cell in 1 mol L^?1 Li₂SO₄ aqueous electrolyte. The Li₂TiO₃ electrode exhibits a specific discharge capacity of 122 mAh g^?1; it can be used as anode in Li battery within the potential window 0.0–1.0 V, while investigated as a supercapacitor electrode, it delivers a specific capacitance of 317 F g^?1 at a current density of 1 mA g^?1 within the potential range ?0.4 to +0.4 V. The demonstration of both anodic and supercapacitor behavior concludes that the nanocrystalline Li₂TiO₃ is a suitable electrode material for supercapattery application.     

Application of photocatalytic technology for NO<Subscript>x</Subscript> removal

Materials that contain a photocatalyst have a semi-permanent capacity for removing harmful gases from the ambient air. It is the purpose of this study to investigate the photocatalytic activity of commercial paints containing TiO₂ nanoparticles towards NO and NO₂. Experiments were carried out in a stainless steel (30 m^-3) walk-in type environmental chamber (Indoortron), under “real world setting” conditions of temperature, relative humidity, irradiation and pollutant concentrations. Two types of nanoparticle TiO₂-containing paints were tested for their depolluting properties: a mineral silicate paint and a water-based styrene acrylic paint. The results showed a significant effect of TiO₂-materials in reducing NO_x. It was found that up to 74% of NO and 27% of NO₂ were photo-catalytically degraded by the mineral silicate paint, while degradation percentage using the styrene acrylic paint reached 91% and 71% for NO and NO₂, respectively. The photo-catalytic rate of NO on the mineral and styrene acrylic paint was calculated to 0.11 μg m^-2 s and 0.18 μg m^-2 s, respectively, indicating higher photocatalytic performance of the organic based material. The effect of relative humidity (RH) was also investigated. An increase of RH from 20% to 50% inhibited the NO_x photocatalysis on the surface of the samples. PACS 81.16.Hc; 81.65.Mq; 82.33.Tb; 82.50.Hp; 82.65.+r     

Non-thermal plasma generation by using back corona discharge on catalyst

This paper discusses a novel plasma catalysis generation method based on back-corona discharge along porous catalyst bed reactor. The reactor consists of a high-voltage needle electrode, one floated mesh electrode, one catalyst bed and one grounded mesh electrode. Typical plasma current density is 11.88 μA/cm². It can be used for ozone generation and volatile organic compounds decomposition. By using a home-made AgMnOx/Al₂O₃-1 catalyst, 90% of toluene is removed at the specific plasma energy density of 123 J/L. At the same time, aerosol byproducts are collected and then decomposed on the catalyst bed. Moreover, the catalyst is regenerated because of the back-corona discharge.     

Spray pyrolysis-deposited TiO<Subscript>2</Subscript> thin films as high-performance lithium ion battery anodes

Focusing on additive-free electrodes, thin films are of typical interest as electrodes for lithium ion battery application. Herein, we report the fabrication of TiO₂ thin films by spray pyrolysis deposition technique. X-ray diffraction and transmission electron microscopic analysis confirms the formation of anatase TiO₂. Electrochemical evaluation of these sub-micron TiO₂ thin films exhibits high-rate performance and long cycling stability. At 1C rate (1C?=?335 mA/g), the electrode delivered discharge capacity of 247 mAh/g allowing about 0.74 lithium into the structure. The electrodes also delivered specific capacities of 122 and 72 mAh/g at 10 and 30C rates, respectively. Without conductive additives, this excellent performance can be attributed to the nanosize effect of TiO₂ particles combined with the uniform porous architecture of the electrode. Upon cycling at high rates (10 and 30C), the electrode exhibited excellent cycling stability and retention, specifically only <?0.6% capacity loss per cycle over 2500 cycles.     

臭氧修饰(001)晶面TiO2纳米片及其光催化降解甲苯研究

本文系统研究了臭氧修饰对(001)主导晶面锐钛矿型TiO₂光催化剂降解甲苯性能的影响. 利用自行搭建的光催化VOCs降解装置对催化剂光降解甲苯的性能进行了测试. 通过多种表征手段,结合原位DRIFTS和DFT计算研究了臭氧表面修饰及甲苯吸附和降解机理. 结果表明,用臭氧进行表面修饰可以显著提高(001)主导晶面TiO₂光催化降解甲苯的性能. (001)晶面上丰富的5c-Ti不饱和配位是臭氧分子的吸附位点,其解离后形成的Ti-O键与H₂O分子结合,在表面生成大量孤立的Ti_5c-OH. Ti_5c-OH 是甲苯分子的吸附位,它的形成显著提高了对甲苯分子的吸附能力. 在光照下Ti_5c-OH与光生空穴结合能形成·OH自由基. 通过臭氧解离产生的O₂也可以与光生电子结合形成超氧自由基. 这些具有强氧化性活性自由基的形成促进了对气相甲苯的光催化降解速率.     

Microwave-induced solid-state synthesis of TiO<Subscript>2</Subscript>(B) nanobelts with enhanced lithium-storage properties

A fast and economical route based on an efficient microwave-induced solid-state process has been developed to synthesize metastable TiO₂(B) nanobelts with widths of 30–100 nm and lengths up to a few micrometers on a large scale. This new method reduces the synthesis time for the preparation of TiO₂(B) nanobelts to less than half an hour, allowing the screening of a wide range of reaction conditions for optimizing and scaling up the production and facilitating the formation of metastable phase TiO₂(B). The as-formed TiO₂(B) nanobelts exhibit enhanced lithium-storage performances, compared with the TiO₂(B) product obtained by the conventional heating. This study provides a new way for large-scale industrial production of high-quality metastable TiO₂(B) nanostructures. The products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and Raman spectroscopy.     

Titanium-modified Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> with a synergistic effect of surface modifying,bulk doping,and size reducing

In this work, a one-step solid-phase sintering process via TiO₂ and Li₂CO₃ under an argon atmosphere, with ultra-fine titanium powder as the modifying agent, was used to prepare a nano-sized Li₄Ti₅O₁₂/Ti composite (denoted as LTO–Ti) at 800 °C. The introduction of ultra-fine metal titanium powder played an important role. First, X-ray photoelectron spectroscopy demonstrates that Ti⁴⁺ was partially changed into Ti³⁺, through the reduction of the ultra-fine metal titanium powder. Second, X-ray diffraction revealed that the ultra-fine metal titanium powder did not react with the bulk structure of Li₄Ti₅O₁₂, while some pure titanium peaks could be seen. Additionally, the size of LTO–Ti particles could be significantly reduced from micro-scale to nano-scale. The structure and morphology of LTO–Ti were characterized by X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy, scanning electron microscopy, and transmission electron microscopy. Electrochemical tests showed a charge/discharge current of 0.5, 1, 5, and 10 C; the discharge capacity of the LTO–Ti electrode was 170, 161, 140, and 111 mAh g^?1. It is believed that the designed LTO–Ti composite makes full use of both components, thus offering a large contact area between the electrolyte and electrode, high electrical conductivity, and lithium-ion diffusion coefficient during electrochemical processes. Furthermore, ultra-fine titanium powder, as the modifying agent, is amenable to large-scale production.     

Titania Gold Composite: Effect of Illumination on Size of Gold Nanoparticles with Consequent Implication on Photocatalytic Water Splitting

This work deals with the study of photodeposition (PD) of gold nanoparticles (AuNPs) on TiO₂ by using different illumination sources, Medium pressure Mercury lamp (ML), Solar Simulator equipped with AM 1.5 (SL) and Tungsten lamp (WL). Different particle size of AuNPs on TiO₂ were obtained by photodeposition method under different illumination sources, which clearly proves the influence of light source on the synthesis of Au–TiO₂. The plasmonic activity of Au–TiO₂ photocatalyst for water splitting reaction was observed to be strongly influenced by the particle size of Au as well as illumination source. Amongst the three different illumination sources used, smallest particle size for AuNP–TiO₂ were observed under ML followed by SL and WL, as revealed by TEM analysis. Different illumination sources were also investigated to evaluate the activity of Au–TiO₂ samples thus prepared under different illumination conditions. The order of hydrogen evolution rate (HER) observed for Au–TiO₂ with different source of illuminations is ML > SL > WL. The highest HER of 1709 μmol/h was observed for Au–TiO₂, which was synthesized and evaluated under ML irradiation. This may be explained on the basis of reduced catalytic activity and photothermal effect of Au nanoparticles with increasing particle size.