Preparation and investigation of composite SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> films

SiO₂-TiO₂ films [Si:Ti = 1:(0.06–2.3)] are obtained by the sol-gel method. The structural and photoluminescent properties of the films and powders heat-treated at different temperatures are studied. It is shown that after 700°C the composite consists of TiO₂ crystallites that are structurally similar to anatase and distributed in an amorphous SiO₂ matrix. The photoluminescence spectra have maxima at 450–500 nm. The photoluminescence intensity depends on the treatment temperature and TiO₂ content. __________ Translated from Zhurnal Prikladnoi Spektroskopii Vol. 74, No. 3, pp. 357–361, May–June, 2007.     

Effect of ethylene carbonate plasticizer and TiO<Subscript>2</Subscript> nanoparticles on 49% poly(methyl methacrylate) grafted natural rubber-based polymer electrolyte

The effect of plasticizer and TiO₂ nanoparticles on the conductivity, chemical interaction and surface morphology of polymer electrolyte of MG49–EC–LiClO₄–TiO₂ has been investigated. The electrolyte films were successfully prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by sol-gel process and was added into the MG49–EC–LiClO₄ electrolyte system. Alternating current electrochemical impedance spectroscopy was employed to investigate the ionic conductivity of the electrolyte films at 25 °C, and the analysis showed that the addition of TiO₂ filler and ethylene carbonate (EC) plasticizer has increased the ionic conductivity of the electrolyte up to its optimum level. The highest conductivity of 1.1 × 10⁻³ Scm⁻¹ was obtained at 30 wt.% of EC. Fourier transform infrared spectroscopy measurement was employed to study the interactions between lithium ions and oxygen atoms that occurred at carbonyl (C=O) and ether (C-O-C) groups. The scanning electron microscopy micrograph shows that the electrolyte with 30 wt.% EC posses the smoothest surface for which the highest conductivity was obtained.     

Luminescence of CaGa<Subscript>2</Subscript>Se<Subscript>4</Subscript>:Eu crystals

We have studied photoluminescence and thermoluminescence (PL and TL) in CaGa₂Se₄:Eu crystals in the temperature range 77–400 K. We have established that broadband photoluminescence with maximum at 571 nm is due to intracenter transitions 4f⁶ 5d–4f⁷ (⁸S_7/2) of the Eu²⁺ ions. From the temperature dependence of the intensity (log I–10³/T), we determined the activation energy (E _a = 0.04 eV) for thermal quenching of photoluminescence. From the thermoluminescence spectra, we determined the trap depths: 0.31, 0.44, 0.53, 0.59 eV. The lifetime of the excited state 4f6 5d of the Eu²⁺ ions in the CaGa₂Se₄ crystal found from the luminescence decay kinetics is 3.8 μsec. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 76, No. 1, pp. 112–116, January–February, 2009.     

Electrical characterization of the [N(CH<Subscript>3</Subscript>)<Subscript>4</Subscript>][N(C<Subscript>2</Subscript>H<Subscript>5</Subscript>)<Subscript>4</Subscript>]ZnCl<Subscript>4</Subscript> compound

The [N(CH₃)₄][N(C₂H₅)₄]ZnCl₄ compound has been synthesized by a solution-based chemical method. The X-ray diffraction study at room temperature revealed an orthorhombic system with P2₁2₁2 space group. The complex impedance has been investigated in the temperature and frequency ranges 420–520 K and 200 Hz–5 MHz, respectively. The grain interior and grain boundary contribution to the electrical response in the material have been identified. Dielectric data were analyzed using the complex electrical modulus M ^* for the sample at various temperature. The modulus plots can be characterized by full width at half height or in terms of a non-exponential decay function ϕ(t) = exp[(−t/τ) ^β ]. The detailed conductivity study indicated that the electrical conduction in the material is a thermally activated process. The variation of the AC conductivity with frequency at different temperatures obeys the Almond and West universal law.     

Magnetic properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>0.47</Subscript>Al<Subscript>0.03</Subscript>O<Subscript>2</Subscript> as positive electrode for Li-ion batteries

The layered LiNi_0.5Mn_0.47Al_0.03O₂ was synthesized by wet chemical method and characterized by X-ray diffraction and analysis of magnetic measurements. The powders adopted the α-NaFeO₂ structure. This substitution of Al for Mn promotes the formation of Li(Ni_0.47²⁺Ni_0.03³⁺Mn_0.47⁴⁺Al_0.03³⁺)O₂ structures and induces an increase in the average oxidation state of Ni, thereby leading to the shrinkage of the lattice unit cell. The concentration of antisite defects in which Ni²⁺ occupies the (3a) Li lattice sites in the Wyckoff notation has been estimated from the ferromagnetic Ni²⁺(3a)–Mn⁴⁺(3b) pairing observed below 140 K. The substitution of 3% Al for Mn reduces the amount of antisite defects from 7% to 6.4–6.5%. The analysis of the magnetic properties in the paramagnetic phase in the framework of the Curie–Weiss law agrees well with the combination of Ni²⁺ (S = 1), Ni³⁺ (S = 1/2) and Mn⁴⁺ (S = 3/2) spin-only values. Delithiation has been made by the use of K₂S₂O₈. According to this process, known to be softer than the electrochemical one, the nickel ions in the (3b) sites are converted into Ni⁴⁺ in the high spin configuration, while Ni²⁺(3a)–Mn⁴⁺(3b) ferromagnetic pairs remain, as the Li⁺(3b) ions linked to the Ni²⁺(3a) ions in the antisite defects are not removed. The results show that the antisite defect is surrounded by Mn⁴⁺ ions, implying the nonuniform distribution of the cations in agreement with previous NMR and neutron experiments.     

Thermostable photocatalytically active TiO<Subscript>2</Subscript> anatase nanoparticles

Anatase is the low-temperature (300–550 °C) crystalline polymorph of TiO₂ and it transforms to rutile upon heating. For applications utilizing the photocatalytic properties of nanoscale anatase at elevated temperatures (over 600 °C) the issue of phase stabilisation is of major interest. In this study, binary TiO₂/SiO₂ particles were synthesized by a flame aerosol process with TiCl₄ and SiCl₄ as precursors. The theoretical Si/Ti ratio was varied in the range of 0.7–1.3 mol/mol. The synthesized TiO₂/SiO₂ samples were heat treated at 900 and 1,000 °C for 3 h to determine the thermostability of anatase. Pyrogenic TiO₂ P25 (from Evonik/Degussa, Germany) widely applied as photocatalyst was used as non-thermostabilized reference material for comparison of photocatalytic activity of powders. Both the non-calcinated and calcinated powders were characterized by means of XRD, TEM and BET. Photocatalytic activity was examined with dichloroacetic acid (DCA) chosen as a model compound. It was found that SiO₂ stabilized the material retarding the collapse of catalyst surface area during calcination. The weighted anatase content of 85% remains completely unchanged even after calcination at 1,000 °C. The presence of SiO₂ layer/bridge as spacer between TiO₂ particles freezes the grain growth: the average crystallite size increased negligibly from 17 to 18 nm even during the calcination at 1,000 °C. Due to the stabilizing effect of SiO₂ the titania nanoparticles calcinated at 900 and 1,000 °C show significant photocatalytic activity. Furthermore, the increase in photocatalytic activity with calcination temperature indicates that the titania surface becomes more accessible either due to intensified cracking of the SiO₂ layer or due to enhanced transport of SiO₂ into the necks thus releasing additional titania surface.     

Synthesis and characterization of electron beam evaporated LiCoO<Subscript>2</Subscript> thin films

LiCoO₂ thin films were prepared by electron beam evaporation technique using LiCoO₂ target with Li/Co ratio 1.1 in an oxygen partial pressure of 5 × 10⁻⁴ mbar. The films prepared at substrate temperature T _s < 573 K were amorphous in nature, and the films prepared at T _s > 573 K exhibited well defined (104), (101), and (003) peaks among which the (104) orientation predominates. The X-ray photoelectron spectroscopy (XPS) and inductively coupled plasma (ICP) data revealed that the films prepared in the substrate temperature range 673–773 K are nearly stoichiometric. The grain size increases with an increase of substrate temperature. The Co–e_g absorption bands, are empty and their peak position lies at around 1.7 eV above the top to the Co–t_2g bands. The fundamental absorption edge was observed at 2.32 eV. The films annealed at 1,023 K in a controlled oxygen environment exhibit (104) out plane texture with large grains. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006     

Electrical properties,equivalent circuit,and dielectric relaxation studies on [(C<Subscript>3</Subscript>H<Subscript>7</Subscript>)<Subscript>4</Subscript>N]<Subscript>2</Subscript>Cd<Subscript>2</Subscript>Cl<Subscript>6</Subscript> polycrystalline

The Ac electrical conductivity and the dielectric relaxation properties of the [(C₃H₇)₄N]₂Cd₂Cl₆ polycrystalline sample have been investigated by means of impedance spectroscopy measurements over a wide range of frequencies and temperatures, 209 Hz–5 MHz and 361–418 K, respectively. The purpose is to make a difference between the electrical and dielectric properties of the polycrystalline sample and single crystal. Besides, a detailed analysis of the impedance spectrum suggests that the electrical properties of the material are strongly temperature-dependent. Plots of (Z" versus Z') are well fitted to an equivalent circuit model consisting of a series combination of grains and grains boundary elements. Moreover, the temperature dependence of the electrical conductivity in the different phases follows the Arrhenius law and the frequency dependence of σ (ω) follows the Jonscher’s universal dynamic law. Furthermore, the modulus plots can be characterized by full width at half height or in terms of a nonexperiential decay function φ(t) = exp(t/t)^β. Finally, the imaginary part of the permittivity constant is analyzed with the Cole–Cole formalism.     

Sonochemical fabrication of morpho-genetic TiO<Subscript>2</Subscript> with hierarchical structures for photocatalyst

Titanium oxides (TiO₂) with hierarchical structures have been successfully replicated from biotemplate using a sonochemical method. The bio-templates, cedarwoods, were irradiated under ultrasonic waves in TiCl₄ solutions and then calcined at temperatures between 450 and 600 °C. The fine replications of the biotemplates in TiO₂ down to nanometer’s level were verified using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The photocatalytic activities were assessed by measuring the percentage degradation of methylene blue using UV–vis spectroscopy. The calcination temperature has a strong effect on the structural replication and photocatalytic activity of the replicas. It appears that the calcination temperature of 450 °C results in the best structural replication with the highest surface area of 54.8 m² g⁻¹, and thus has the best photocatalytic properties. This method provides a simple, efficient, and versatile technique for fabricating TiO₂ with hierarchical structures, and it has the potential to be applied to other systems for producing functional hierarchical materials for chemical sensor and nanodevices.     

Synthesis and characterization of single crystalline SnO<Subscript>2</Subscript> nanorods by high-pressure pulsed laser deposition

Tin oxide (SnO₂) nanorods were grown by high-pressure pulsed laser deposition (PLD). The nanorods were grown without the use of a catalyst but required high background pressure growth in order to realize small grain columnar growth and nanorod formation, with nanorod formation most favored on non-epitaxial substrates. The structures and morphology were characterized by field emission scanning electron microscopy (FESEM) and high resolution transmission electron microscopy (HRTEM). X-ray diffraction and HRTEM analysis indicate that the as-grown SnO₂ nanorods are single crystals with a rutile structure. The nanorods are approximately 50–90 nm in diameters and 1.5 μm in length. This method provides an approach for large area synthesis of one dimensional SnO₂ nanostructure materials. PACS 81.16.Mk; 61.46.-w; 81.07.-b     

Photoluminescence of fluoroacrylate polymers impregnated with Eu(bta)<Subscript>3</Subscript> using supercritical CO<Subscript>2</Subscript>

Optical properties (photoluminescence and absorption) of Eu(bta)₃(B) _n (B = H₂O or 1,10-phenanthroline) polycrystalline powders and fluoroacrylate polymers (FAPs) impregnated with these compounds using supercritical CO₂ (SC CO₂) were investigated. It was established that impregnation of Eu(bta)₃phen into the FAPs using an SC CO₂ solution was difficult to achieve. The type of B (ancillary ligand) and the polymer matrix were shown to influence the temperature quenching of photoluminescence of Eu³⁺ ions in the range 25–100°C. A comparative analysis of quantum yields (λ_ex = 300 and 380 nm) and photoluminescence decay times (λ_ex = 337.1 nm) for Eu(bta)₃B _n and for Eu(bta)₃B _n -doped FAPs was performed.     

Structural and electrical properties of pure and H<Subscript>2</Subscript>SO<Subscript>4</Subscript> doped (PVA)<Subscript>0.7</Subscript>(NaI)<Subscript>0.3</Subscript> solid polymer electrolyte

Solid polymer electrolytes (SPE) based on poly-(vinyl alcohol) (PVA)_0.7 and sodium iodide (NaI)_0.3 complexed with sulfuric acid (SA) at different concentrations were prepared using solution casting technique. The structural properties of these electrolyte films were examined by X-ray diffraction (XRD) studies. The XRD data revealed that sulfuric acid disrupt the semi-crystalline nature of (PVA)_0.7(NaI)_0.3 and convert it into an amorphous phase. The proton conductivity and impedance of the electrolyte were studied with changing sulfuric acid concentration from 0 to 5.1 mol/liter (M). The highest conductivity of (PVA)_0.7(NaI)_0.3 matrix at room temperature was 10⁻⁵ S cm⁻¹ and this increased to 10⁻³ S cm⁻¹ with doping by 5.1 M sulfuric acid. The electrical conductivity (σ) and dielectric permittivity (ε′) of the solid polymer electrolyte in frequency range (500 Hz–1 MHz) and temperature range (300–400) K were carried out. The electrolyte with the highest electrical conductivity was used in the fabrication of a sodium battery with the configuration Na/SPE/MnO₂. The fabricated cells give open circuit voltage of 3.34 V and have an internal resistance of 4.5 kΩ.     

Structural and sensing properties of nanocrystalline SnO<Subscript>2</Subscript> films deposited by spray pyrolysis from a SnCl<Subscript>2</Subscript> precursor

We report the fabrication and characterization of tin dioxide gas sensing layers. The tin dioxide layers were synthesized using a convenient, simple and low-cost technique of spray pyrolysis. The formation of stoichiometric SnO₂ layers with fine-grain structure is revealed by Rutherford backscattering spectroscopy. The microstructure, phase, nanoparticle size distribution and surface morphology were studied by transmission electron microscopy, electron diffraction and atomic force microscopy. Most of the grains were of 10–20 nm size; however, some particles were up to 100 nm in size and had a microtwin lamellae structure of SnO₂ phase (cassiterite) with lattice parameters a= 0.474 nm and c= 0.319 nm. The sensitivity of the layers with respect to 1000–10000 ppm CH₄ in air was obtained from both resistivity (S_R) and capacity (S_C) measurements at 330 °C and values of S_R=5–7 and S_C=22–31 were extracted. PACS 68.43.-h; 68.55.-a; 81.05.Hd; 81.07.-b; 81.15.Rs     

Influence of carbon additive on the properties of spherical Li<Subscript>4</Subscript>Ti<Subscript>5</Subscript>O<Subscript>12</Subscript> and LiFePO<Subscript>4</Subscript> materials for lithium-ion batteries

Preparing spherical particles with carbon additive is considered as one effective way to improve both high rate performance and tap density of Li₄Ti₅O₁₂ and LiFePO₄ materials. Spherical Li₄Ti₅O₁₂/C and LiFePO₄/C composites are prepared by spray-drying–solid-state reaction method and controlled crystallization–carbothermal reduction method, respectively. The X-ray diffraction characterization, scanning electron microscope, Brunauer–Emmett–Teller, alternating current impedance analyzing, tap density testing, and electrochemical property measurements are investigated. After hybridizing carbon with a proper quantity, the crystal grain size of active materials is remarkably decreased and the electrochemical properties are obviously improved. The Li₄Ti₅O₁₂/C and LiFePO₄/C composites prepared in this work are spherical. The tap density and the specific surface area are as high as 1.71 g cm⁻³ and 8.26 m² g⁻¹ for spherical Li₄Ti₅O₁₂/C, which are 1.35 g cm⁻³ and 18.86 m² g⁻¹ for spherical LiFePO₄/C powders. Between 1.0 and 3.0 V versus Li, the reversible specific capacity of the Li₄Ti₅O₁₂/C is more than 150 mAh g⁻¹ at 1.0-C rate. Between 2.5 and 4.2 V versus Li, the reversible capacity of the LiFePO₄/C is close to 140 mAh g⁻¹ at 1.0-C rate.     

Electrical properties of Na<Subscript>2</Subscript>SO<Subscript>4</Subscript>-based composite systems

Composite electrolytes are well-known multiphase systems and exhibit maxima in the conductivity at certain second-phase concentration. An attempt has been made to investigate a number of sodium sulfate (Na₂SO₄)-based composite systems. The dispersoids that have been used are MgO, Al₂O₃, and SiO₂. The samples have been characterized using impedance spectroscopy, X-ray diffraction, and differential scanning calorimetry. The maximum conductivity has been observed for MgO dispersed system, and the percolation threshold has been observed at 30-mol% dispersoid, MgO concentration. Interestingly, two maxima have been observed in case of the Na₂SO₄–SiO₂ and Na₂SO₄–Al₂O₃ composite systems. In the Na₂SO₄–SiO₂ system, the first maximum occurs at lower concentration, i.e., in the range between 10 and 20 mol%, whereas the second occurs at the 40-mol% dispersoid concentration. For the Na₂SO₄–Al₂O₃ system, although slightly indistinguishable, two peaks in the conductivity vs composition plot have been observed around 12- and 30-mol% Al₂O₃ concentrations.     

Broadband infrared luminescence from transparent glass–ceramics containing Ni<Superscript>2+</Superscript>-doped <Emphasis Type="BoldItalic">β</Emphasis> -Ga<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocrystals

Transparent Ni²⁺-doped β-Ga₂O₃ glass–ceramics were synthesized. The nanocrystal phase in the glass–ceramics was identified to be β-Ga₂O₃ and its size was about 3.6 nm. It was confirmed from the absorption spectra that the ligand environment of Ni²⁺ ions changed from the trigonal bi-pyramid fivefold sites in the as-cast glass to the octahedral sites in the glass–ceramics. The broadband infrared emission centering at 1270 nm with full width at half maximum (FWHM) of more than 250 nm was observed. The fluorescence lifetime was about 1.1 μs at room temperature. The observed infrared emission could be attributed to the ³ T _2g (³ F )→³ A _2g (³ F ) transition of octahedral Ni²⁺ ions. It is suggested that the Ni²⁺-doped transparent β-Ga₂O₃ glass–ceramics with broad bandwidth and long lifetime have a potential as a broadband amplification medium. PACS 42.70.-a; 42.70.Ce; 81.40.Tv     

Characterization of TiO<Subscript>2</Subscript> nanoparticle suspensions for electrophoretic deposition

The rheology of suspensions is critically important for the successful achievement of defect-free TiO₂ deposits by electrophoretic deposition (EPD). The rheological behaviour of TiO₂ nanoparticle suspensions in acetylacetone with and without iodine was investigated over a broad solid-concentration range (0.3–2.5 wt.%) and at different shear rates ( = 10–250 s⁻¹). The influence of these parameters on the quality of TiO₂ films obtained by EPD on stainless steel substrates was assessed. The pure solvent and the 1 wt.% TiO₂ nanoparticles suspension without iodine exhibited shear-thickening flow behaviour. For other concentrations, the suspensions showed shear-thinning behaviour followed by an apparent shear-thickening effect at a critical shear rate (100 s⁻¹). For the suspension with 1 wt.% TiO₂ containing iodine, a shear-thickening flow behaviour was observed over the whole shear rate range investigated. The maximum solids fraction (ϕ_m) was experimentally determined from a linear relationship between solid concentration and viscosity. The estimated value was ϕ_m = 7.94 wt.% for this system. Using a suspension with 1 wt.% concentration, good-quality TiO₂ deposits on stainless steel planar substrates were obtained by EPD at constant voltage condition. The influence of pH on suspension stability was determined in the range pH = 1–9, being pH ≈ 5 the optimal value for this system in terms of EPD results.     

Tunable bluish green to yellowish green Ca<Subscript>2(1-x)</Subscript>Sr<Subscript>2x</Subscript>Al<Subscript>2</Subscript>SiO<Subscript>7</Subscript>:Eu<Superscript>2+</Superscript> phosphors for potential LED application

A series of solid solutions with a general formula of Ca_2(1-x)Sr_2xAl₂SiO₇:Eu²⁺ were synthesized by a high temperature solid state reaction. The structure, diffuse reflection spectra, photoluminescence spectra, color-coordinate parameters and lifetimes of phosphors were investigated. XRD results show that Ca₂Al₂SiO₇ is totally miscible with Sr₂Al₂SiO₇. These solid solution phosphors show a broad excitation band of 350–450 nm that matches well with the output lights of near-UV LEDs and tunable emission from bluish green to yellowish green. These optical properties originate from the 4f⁷–4f⁶5d transition of Eu²⁺ ions. The crystal field strength was considered to be tailed by controlling the host composition, which leads to the shift of absorption band and emission band, and the varying of color coordinates. PACS  78.55.-m; 42.70.-a; 61.05.C-     

RETRACTED ARTICLE: Refractive-index tailoring and morphological evolutions in Gd<Subscript>2</Subscript>O<Subscript>3</Subscript>–SiO<Subscript>2</Subscript> and ZrO<Subscript>2</Subscript>–SiO<Subscript>2</Subscript> composite thin films

Refractive-index tailoring and morphological evolutions in two different thin film composite systems of gadolinia–silica (Gd₂O₃:SiO₂) and zirconia–silica (ZrO₂:SiO₂) deposited through reactive electron-beam codeposition processes are discussed in this research paper. For Gd₂O₃:SiO₂ the refractive-index tuning has been achieved from 1.45 to 2.18, whereas in the case of ZrO₂:SiO₂ the achieved tunable range is from 1.45 to 2.45 in the ultraviolet region. Under certain compositional mixings with lower silica fractions both the systems demonstrated relative microstructural and morphological densifications. Such evolutions were very successfully derived through phase-modulated ellipsometry and atomic force microscopy. The composition-dependent refractive-index tailoring and microstructural densifications have been investigated by adopting Tauc–Lorentz and single-effective-oscillator models. The morphological correlation functions have also very aptly supported such evolutions in these composite films. These experimental results indicate their favourable properties and applicability down to the extreme ultraviolet wavelength region of the electromagnetic spectrum. PACS 42.79.Wc; 78.66.-w; 78.20.Ci; 61.16.Ch; 42.70.-a;68.55.-a; 68.35.Bs; 81.15.Ef     

Total and ionization cross-sections of N<Subscript>2</Subscript> and CO by positron impact: Theoretical investigations

In this paper we report our calculations on several important total cross-sections (TCSs) of positron impact on isoelectronic N₂ and CO molecules, treated in the complex spherical potential formalism. Basically the total (complete) cross-section Q _T consists of elastic and inelastic contributions. Our total inelastic cross-section (Q _inel) contains ionization and electronic excitations together with positronium formation. Our goal here is to bifurcate Q _inel further to deduce total ionization cross-section, using the ‘complex scattering potential–ionization contribution’ (CSP-ic) method of electron–atom/molecule scattering. The present range of positron energy is 15–2000 eV. All the resulting cross-sections are in a good general accord with the existing data. This work highlights the importance of various scattering channels in e⁺-N₂ and e⁺-CO interactions at intermediate and high energies.