Application of liquid chromatography to the simultaneous determination of acetylsalicylic acid, caffeine, codeine, paracetamol, pyridoxine, and thiamine in pharmaceutical preparations.

This paper describes a rapid reversed-phase liquid chromatographic method, with UV detection, for the simultaneous determination of acetylsalicylic acid, caffeine, codeine, paracetamol, pyridoxine, and thiamine in pharmaceutical preparations. A reversed-phase C18 Nucleosil column is used. The mobile phase consists of 2 successive eluants: water (5 min) and acetonitrile-water (75 + 25, v/v; 9 min), both adjusted to pH 2.1 with phosphoric acid. Before determination acetylsalicylic acid is completely converted to salicylic acid by alkaline hydrolysis. Salicylic acid, caffeine, paracetamol, pyridoxine, and thiamine are all detected at 285 nm, whereas codeine is detected at 240 nm. Calibration curves were linear for salicylic acid, caffeine, paracetamol, and pyridoxine in the range of 50-500 mg/L, and for codeine and thiamine in the range of 50-1000 mg/L. The method was applied to the analysis of 13 fortified commercial pharmaceutical preparations. Recoveries ranged from 92.6 to 105.5%, with relative standard deviations of 1.1-5.8%.     

Determination of ethephon residues in water by gas chromatography with cubic mass spectrometry after ion-exchange purification and derivatisation with N-(tert-butyldimethylsilyl)-N-methyltrifluoroacetamide

An analytical method has been developed for the determination of residues of ethephon (2-chloroethyl phosphonic acid) in drinking and surface water. The procedure is based on de-ionisation with an anion/cation-exchange resin, solid phase extraction by means of anion-exchange polystyrene-divinylbenzene extraction disks, elution with a mixture of methanol and 10 M hydrochloric acid (98/2, v/v), redisolution into acetonitrile after evaporation and silylation with N-(tert-butyldimethylsilyl)-N-methyltrifluoroacetamide (MTBSTFA). Quantification is performed by gas chromatography with ion-trap cubic mass spectrometric detection in the electron impact mode (GC-EI-MS3). Method validation was conducted using samples of mineral, tap, and river water that were fortified with ethephon at concentration levels ranging from 0.1 to 1.0 microg/L. The mean recovery from all the fortified samples (n = 36) amounted to 88% with a relative standard deviation of 17%. The method, therefore, was shown to allow accurate determination of ethephon residues in drinking and surface water with a limit of quantification of 0.1 microg/L.     

Reversed-phase liquid chromatography/electrospray ionization/mass spectrometry with isotope dilution for the analysis of nitrate and nitrite in water

A new method was developed for the analysis of nitrate and nitrite in a variety of water matrices by using reversed-phase liquid chromatography/electrospray ionization/mass spectrometry in the negative ion mode. For this direct analysis method, nitrate and nitrite anions were well separated under the optimized LC conditions, detected by monitoring m/z 62 and m/z 46 ions, and quantitated by using an isotope dilution technique that utilized the isotopically labeled analogs. The method sensitivity, accuracy, and precision were investigated, along with matrix effects resulting from common inorganic matrix anions. The isotope dilution technique, along with sample pretreatment using barium, silver, and hydrogen cartridges, effectively compensated for the ionization suppression caused by the major water matrix anions, including chloride, sulfate, phosphate, and carbonate. The method detection limits, based on seven reagent water replicates fortified at 0.01 mg N/L nitrate and 0.1 mg N/L nitrite, were 0.001 mg N/L for nitrate and 0.012-0.014 mg N/L for nitrite. The mean recoveries from the replicate fortified reagent water and lab water samples containing the major water matrix anions, were 92-103% for nitrate with an imprecision (relative standard deviation, RSD) of 0.4-2.1% and 92-110% for nitrite with an RSD of 1.1-4.4%. For the analysis of nitrate and nitrite in drinking water, surface water, and groundwater samples, the obtained results were generally consistent with those obtained from the reference methods. The mean recoveries from the replicate matrix spikes were 92-123% for nitrate with an RSD of 0.6-7.7% and 105-113% for nitrite with an RSD of 0.3-1.8%.     

Determination of microcystin-LR in drinking water using UPLC tandem mass spectrometry-matrix effects and measurement

A simple detection method using ultra-performance liquid chromatography electrospray ionisation tandem mass spectrometry (UPLC-ESI-MS-MS) coupled with the sample dilution method for determining trace microcystin-LR (MC-LR) in drinking water is presented. The limit of detection (LOD) was 0.04 μg/L and the limit of quantitation (LOQ) was 0.1 μg/L. Water matrix effects of ionic strength, dissolved organic carbon (DOC) and pH were examined. The results indicate that signal detection intensity for MC-LR was significantly suppressed as the ionic strength increased from ultrapure water condition, whereas it increased slightly with solution pH and DOC at low concentrations. However, addition of methanol (MeOH) into the sample was able to counter the signal suppression effects. In this study, dilution of the tap water sample by adding 4% MeOH (v/v) was observed to be adequate to compensate for the signal suppression. The recoveries of the samples fortified with MC-LR (0.2, 1, and 10 μg/L) for three different tap water samples ranged from 84.4% to 112.9%.     

Liquid chromatographic determination of fosthiazate residues in environmental samples and application of the method to a fosthiazate field dissipation study

A method was developed and validated for the determination of residues of the organophosphorus nematicide fosthiazate in soil and water by using reversed-phase liquid chromatography with UV detection. Good recoveries (>85%) of fosthiazate residues were obtained from water samples (drinking water, groundwater, and liquid chromatography water) after passage of 0.5-2 L water through solid-phase extraction (SPE) C-18 cartridges and subsequent elution with ethyl acetate. Residues in soil were extracted with methanol-water (75 + 25, v/v) on a wrist-action shaker, and the extract was cleaned up on C-18 SPE cartridges before analysis. The method was validated by analysis of a range of soils with different physicochemical characteristics; recoveries exceeded 87% at fortification levels ranging from 0.02 to 5.0 mg/kg. The precision values obtained for the method, expressed as repeatability and reproducibility, were satisfactory (<11%). Fosthiazate detection limits were 0.025 microg/L and 0.005 mg/kg for water and soil samples, respectively. The decline in the levels of fosthiazate residues in soil was measured after application of fosthiazate to protected tomato cultivation. The dissipation of fosthiazate residues followed first-order kinetics with a calculated half-life of 21 days.     

Compliance analysis of phenylurea and related compounds in drinking water by liquid chromatography/electrospray ionization/mass spectrometry coupled with solid-phase extraction

A liquid chromatography/electrospray ionization/mass spectrometry method was reported for the compliance analysis of seven phenylurea compounds and two related herbicides (tebuthiuron and propanil) in drinking water. The volumes of the sample and final extract used in the method were 500 mL and 10 mL, respectively. The obtained method detection limits were less than 0.03 microg/L, and the mean recoveries were 74-128% with a relative standard deviation of 2.6-8.3% for all the studied compounds. The peak-to-peak signal-to-noise ratios ranged from 3.3 for cis-siduron to 34.2 for fluometuron. The accuracy and precision resulting from reagent and drinking water samples fortified at higher concentration levels were similar to these results. Several analytes were detected in the drinking water samples, including tebuthiuron at 0.5 microg/L, propanil at 0.7 microg/L, diuron at 0.1-2.1 microg/L, and linuron at 0.1-0.8 microg/L.     

High performance liquid chromatographic determination of methylxanthines in canine serum, gastric and pancreatic juices

A convenient high performance liquid chromatographic method for the determination of methylxanthines in biological samples is described. Separation was achieved by reversed phase chromatography using a mobile phase consisting of tetrahydrofuran + methanol + 0.01M potassium dihydrogen phosphate, pH 3.5 (1:20:79, v/v/v), on a 7 microns C18 column and a C18 Lichrosorb precolumn at a flow rate of 0.8 mL/min. Levels varying from 0.25-16 mg/L could be detected by UV at 280 nm. In this range, standard curves were established for 4 methylxanthines: theobromine, paraxanthine, theophylline and caffeine in 4 media: mobile phase, serum, gastric and pancreatic juices, and were found to be linear (r greater than or equal to 0.9975). Overall characteristics of the method were determined as: percent recovery (89.54%), accuracy (greater than or equal to 99.4%) and reproducibility (greater than or equal to 95%). Retention times ranged from 4.21 +/- 0.01 (1-methyluric acid) to 10.8 +/- 0.03 min (caffeine). Animal experiments (5 and 10 mg/kg boluses) were used to determine caffeine half life in dog's blood (310 +/- 46 and 453 +/- 59 min, respectively) and its secretion into pentagastrin stimulated gastric juice (mean concentrations 2.51 and 6.04 mg/L; mean outputs 351 and 1206 micrograms/2.25 h; both statistically different at p less than 0.001 level).     

Determination of polycyclic aromatic compounds in fish tissue

A method is presented for the analysis of polycyclic aromatic hydrocarbons (PAHs), polycyclic aromatic sulfur heterocycles (PASHs), and basic polycyclic aromatic nitrogen heterocycles (PANHs) in fish. The analytical procedure includes Soxhlet extraction of prepared fish tissue with methylene chloride followed by gel permeation chromatography (GPC) using Bio-beads SX-3. For PAHs/PASHs, further cleanup is performed using adsorption chromatography on Florisil (5% water deactivated) and elution with hexane. For basic PANHs further cleanup of the fish extracts after GPC is achieved using liquid-liquid partitioning with 6 M hydrochloric acid and chloroform and then basifying the aqueous phase and extracting it with chloroform. Analysis of fortified fish samples was performed using capillary gas chromatography with flame ionization detection and capillary gas chromatography-mass spectrometry. Good agreement was observed for both methods of analysis when applied to fish samples fortified with PAHs, PASHs and basic PANHs at 0.1 to 1 microgram/g, suggesting that the method is effective at removing interfering biogenic compounds prior to analysis. Average recovery of PAHs/PASHs from fortified fish tissue was 87% and 70% for fish tissue fortified at 0.24-1.1 and 0.024-0.11 microgram/g, respectively. Average recovery for basic PANHs was 97% for fish fortified at 1.2-1.4 micrograms/g.     

Determination of acephate in human urine

Acephate is a commonly used organophosphate insecticide applied on agricultural crops and in residential communities. Because very little acephate is metabolized prior to excretion, the parent pesticide compound can be measured in human urine. The residue method must be sensitive enough to determine human exposure and potential health risk for both agricultural workers and their families who may be exposed by pesticide drift or by inadvertent carry-home residues. A reliable and sensitive method was developed to measure acephate concentrations in human urine. Urine was diluted with water and acetone, adjusted to a neutral pH, and partitioned twice in acetone-methylene chloride (1 + 1, v/v), with NaCl added to aid separation. The solvent-reduced organic phase extracts were clarified by activated charcoal solid-phase extraction and then adjusted to a final volume with the addition of a D-xylose analyte protectant solution to reduce matrix enhancement effects. Acephate concentrations in urine were determined by gas chromatography using pulsed flame photometric detection. The method limit of detection was established at 2 microg/L, with a method limit of quantitation of 10 microg/L. The average recovery from urine fortified with 10-500 microg/L was 102 +/- 12% (n = 32).     

超高效液相色谱-串联质谱法同时检测地表水中18种药物与个人护理品的残留量

采用固相萃取对水样进行预处理,建立了同时检测地表水中包括抗生素、β-阻滞剂、驱蚊剂、抗癫痫药、中枢神经兴奋剂、血脂调节剂、非甾体抗炎药、杀菌消毒剂在内的18种药物与个人护理品的超高效液相色谱-串联质谱分析方法。采用中性条件萃取水样,控制上样流速为2 mL/min,用甲醇-乙腈(1:1, v/v)溶液洗脱。纯水中的平均加标回收率为53.9%～112%,相对标准偏差为2.6%～15.3%(n=6);以地表水样加标100 ng/L为样品,目标分析物平均回收率为45.1%～156.6%,相对标准偏差为2.4%～15.7%(n=6)。结果表明,本方法可同时精确检测地表水样中的18种分析物,方法验证结果表明所建立的方法可靠。用该方法分析杭州余杭塘河水,结果检出9种分析物,其中咖啡因平均质量浓度达550.7 ng/L。结果表明该方法可靠。     

Application of NaClO-treated multiwalled carbon nanotubes as solid phase extraction sorbents for preconcentration of trace 2,4-dichlorophenoxyacetic acid in aqueous samples

Multiwalled carbon nanotubes functionalized by oxidation of original multiwalled carbon nanotubes with NaClO were prepared and their application as solid phase extraction sorbent for 2,4-dichlorophenoxyacetic acid (2,4-D) was investigated systemically, and a new method was developed for the determination of trace 2,4-D in water samples based on extraction and preconcentration of 2,4-D with solid phase extraction columns packed with NaClO-treated multiwalled carbon nanotubes prior to its determination by HPLC. The optimum experimental parameters for preconcentration of 2,4-D, including the column activating conditions, the amount of the sorbent, pH of the sample, elution composition, and elution volume, were investigated. The results indicated 2,4-D could be quantitatively retained by 100 mg NaClO-treated multiwalled carbon nanotubes at pH 5, and then eluted completely with 10 mL 3:1 (v/v) methanol-ammonium acetate solution (0.3 mol/L). The detection limit of this method for 2,4-D was 0.15 μg/L, and the relative standard deviation was 2.3% for fortified tap water samples and 2.5% for fortified riverine water sample at the 10 μg/L level. The method was validated using fortified tap water and riverine water samples with known amount of 2,4-D at the 0.4, 10, and 30 μg/L levels, respectively.     

Quantitative trace-level speciation of arsenite and arsenate in drinking water by ion chromatography

We describe an improved method for the determination of inorganic arsenic in drinking water. The method is based on comprehensive optimization of the anion-exchange ion chromatographic (IC) separation of arsenite and arsenate with post-column generation and detection of the arsenate-molybdate heteropoly acid (AMHPA) complex ion. The arsenite capacity factor was improved from 0.081 to 0.13 by using a mobile phase (2.0 mL min(-1)) composed of 2.5 mM Na2CO3 and 0.91 mM NaHCO3 (pH 10.5). A post-column photo-oxidation reactor (2.5 m x 0.7 mm) was optimized (0.37 microM potassium persulfate at 0.50 mL min(-1)) such that arsenite was converted to arsenate with 99.8 +/- 4.2% efficiency. Multi-variate optimization of the complexation reaction conditions yielded the following levels: 1.3 mM ammonium molybdate, 7.7 mM ascorbic acid, 0.48 M nitric acid, 0.17 mM potassium antimony tartrate, and 1.0% (v/v) glycerol. A long-path length flow cell (Teflon AF, 100-cm) was used to measure the absorption of the AMHPA complex (818 +/- 2 nm). Figures of merit for arsenite/arsenate include: limit of detection (1.6/0.40 microg L(-1)): standard error in absorbance (5.1 x 10(-3)/3.5 x 10(-3)); and sensitivity (2.9 x 10(-3)/2.2 x 10(-3) absorbance units per ppb). Successful application of the method to fortified surface and ground waters (100 microL samples) is also described.     

High-performance liquid chromatography column switching applied to the trace determination of herbicides in environmental and drinking water samples

A selective and sensitive coupled-column high-performance liquid chromatographic method is developed for the simultaneous determination of 5 phenylurea herbicides (monuron, linuron, isoproturon, monolinuron, and diuron) in environmental and drinking water samples. Sample clean-up is performed automatically by means of a column switching technique. Using 2 octadecyl silica columns connected via two programmable 6-port valves and ultraviolet detection at 244 nm, the aforementioned compounds can be determined at the low concentration levels required for pesticide residue analysis in water samples. A mobile phase consisting of a mixture of methanol-water (55:45, v/v) is pumped at 1 mL/min. For the 5 phenylureas, high recoveries ranging from 94.9 to 101.6%, good reproducibility with relative standard deviations lower than 5%, and wide linear ranges up to 20 micrograms/L are observed with determination limits of 0.05 microgram/L. The method is successfully applied to the screening of different environmental water samples such as surface, ground, rain, and drinking water.     

Trace analysis of tiamulin in honey by liquid chromatography-diode array-electrospray ionization mass spectrometry detection

A liquid chromatography with diode array or electrospray ionisation mass spectrometry detection (LC-DAD-ESI-MS) method for the determination of tiamulin residues in honey is presented. The procedure employs a solid-phase extraction (SPE) on polymeric cartridges for the isolation of tiamulin from honey samples diluted in aqueous solution of tartaric acid. Chromatographic separation of the tiamulin is performed, in isocratic mode, on a C18 column using methanol and ammonium carbonate 0.1% in water, in proportion (30:70, v/v). Average analyte recoveries were from 88 to 106% in replica sets of fortified honey samples. The LC-ESI-MS method detection limits differ from 0.5 microg kg(-1) for clear honeys to 1.2 microg kg(-1) for dark honeys. The developed method has been applied to the analysis of tiamulin residues in multifloral honey samples collected from veterinary treated beehives.     

Determination of dimetridazole, ronidazole and their common metabolite in poultry muscle and eggs by high performance liquid chromatography with UV detection and confirmatory analysis by atmospheric pressure chemical ionisation mass spectrometry.

A method was developed for the determination of the nitroimidazole compounds dimetridazole (DMZ) and ronidazole (RNZ) and their common metabolite, 2-hydroxymethyl-1-methyl-5-nitroimidazole (2-OH-M). Extracts obtained from a clean-up process using strong cation exchange (SCX) solid phase extraction (SPE) can be analysed either by high performance liquid chromatography with UV detection (HPLC-UV) or by high performance liquid chromatography with atmospheric pressure chemical ionisation mass spectrometry (HPLC-APCI-MS) as a confirmatory method. Up to 20 samples can be extracted in approximately 4 h. The HPLC-UV analysis had a limit of detection of 0.5 microgram kg-1. Validation in chicken muscle fortified at a concentration of 5 micrograms kg-1 gave recoveries of 75% DMZ, 77% RNZ and 81% 2-OH-M with RSDs of 16.4, 11.3 and 14.0%, respectively (n = 17). Validation in egg fortified at the same concentration gave recoveries of 77% DMZ, 80% RNZ and 80% 2-OH-M, with RSDs of 14.9, 22.0 and 18.2%, respectively (n = 18). The limit of detection of the HPLC-APCI-MS method was 0.1 microgram kg-1 for DMZ and RNZ and 0.5 microgram kg-1 for 2-OH-M. This method gave mean recoveries in fortified egg samples of 65% DMZ, 87% RNZ and 75% 2-OH-M with RSDs of 22, 11 and 14%, respectively (n = 10). The ratios of the peak areas of the molecular ion and a fragment ion were monitored as added confirmation of the presence of the analyte. Both the HPLC-UV screening procedure and the HPLC-APCI-MS confirmatory method have subsequently been used for the analysis of several hundred samples as part of UK surveillance programmes.     

Determination of acidic drugs and caffeine in municipal wastewaters and receiving waters by gas chromatography-ion trap tandem mass spectrometry

Some aspects of both sample preparation and instrumental techniques for analysis of such acidic drugs as acetylsalicylic acid, ibuprofen, gemfibrozil, fenoprofen, naproxen, ketoprofen, and diclofenac, as well as caffeine in surface water and municipal wastewater have been studied and further developed. Water samples were filtered and target analytes were extracted by solid-phase extraction (SPE). Supelco LC-18 and Oasis HLB SPE cartridges were used to pre-concentrate samples for acidic drugs and caffeine, respectively. A methylation process was applied to acidic drugs prior to analysis while caffeine was analyzed directly. A method of gas chromatography-ion trap tandem mass spectrometry (IT-MS/MS) for analysis of the target acidic pharmaceuticals and caffeine is presented here in detail. Such parameters as collision-induced dissociation (CID) voltage, isolation time, excitation time, excitation storage level, and electron energy were adjusted in order to optimize the instrument analytical performance. After optimization, an instrument detection limit of 0.5-20 pg/microL with signal-to-noise (S/N) not less than 5 was achieved for all target analytes. It was shown that this method has good linearity within the range of 10-2000 pg/microL. The application of the optimized IT-MS/MS parameters conjointly with the sample preparation procedure resulted in method detection limits (MDLs) of 0.1-1.0 and 20 ng/L for the determination of acidic drugs and caffeine, respectively in such samples as surface water, effluent from municipal wastewater plants, as well as receiving waters.     

固相萃取/超高效液相色谱-串联质谱法快速测定不同水体中5种人造甜味剂、6种造影剂及咖啡因

建立了快速检测不同水样(地表水、污水处理厂进水和出水)中5种人造甜味剂、6种造影剂和咖啡因的超高效液相色谱-串联质谱(UPLC-MS/MS)方法。利用HR-X固相萃取柱对过滤后的水样进行富集净化。采用Zorbax SB-C_(18)色谱柱分离,电喷雾正模式(ESI+)和负模式(ESI-)下分别以乙腈-水(10 mmol/L乙酸铵,0.01%甲酸)和乙腈-水(5 mmol/L乙酸铵,1 mmol/L Tris)为流动相,多反应监测模式(MRM)检测。各目标化合物在5~5 000μg/L范围内线性关系良好,相关系数均大于0.998。地表水、污水处理厂进水和出水的回收率为70%~120%,相对标准偏差(RSD)为0.8%~19.0%,方法检出限(MDL)分别为0.43~13.8、1.80~34.8、2.30~134 ng/L。应用该方法对广州某污水处理厂进水和出水及受纳河流河水进行检测,除阿斯巴甜、碘他拉酸、碘普罗胺、碘美普尔外,其他物质均有检出且浓度较高。该方法准确、灵敏、操作简便,适用于多种环境水样中人造甜味剂、造影剂和咖啡因的分析检测。     

HPLC analysis of methylxanthines in human breast milk

A sensitive and specific high-performance liquid chromatographic (HPLC) procedure is developed for simultaneously quantitating the levels of caffeine, theophylline, theobromine and paraxanthine in breast milk. The method involved the precipitation of proteins present in the milk samples with a 6% v/v perchloric acid solution containing the internal standard, proxyphylline, followed by centrifugation at 12,800 Xg for 10 minutes. The clear supernatant was then chromatographed on a C18 reversed-phase analytical column at ambient temperature using a wavelength of 272 nm. Samples were eluted from the column at a constant flow rate of 1.5 mL/min using a gradient program in which the concentration of methanol in the mobile phase varied from 0 to 16%. The mean recoveries of the methylxanthines averaged over all the concentrations examined were generally excellent and ranged from 96.3 +/- 5.4% for caffeine to 102.3 +/- 8.9% for paraxanthine. The assay precision was very good and the peaks of interest were extremely well resolved. The method is recommended for assessing the total caffeine and dimethylxanthine load to which the nursing infant is exposed in mothers ingesting typical amounts of caffeine.     

Application of sample pre-oxidation of arsenite in human urine prior to speciation via on-line photo-oxidation with membrane hydride generation and ICP-MS detection

A pre-oxidation procedure which converts arsenite [As(III)] into arsenate [As(v)] was investigated in urinary arsenic speciation prior to on-line photo-oxidation hydride generation with ICP-MS detection. This sample pre-oxidation method eliminates As(III) and As(v) preservation concerns and simplifies the chromatographic separation. Four oxidants, Cl2, MnO2, H2O2 and I3-, were investigated. Chlorine (ClO-aq) and MnO2 selectively converted As(III) into As(v) in pure water samples, but the conversion was inefficient in the complex urine matrix. Oxidation of As(III) by H2O2 was least affected by the urine matrix, but the removal of excess H2O2 at pH 10 proved difficult. The most appropriate oxidant for the selective conversion of As(III) into As(v) with minimal interference from the urine matrix is I3- at pH 7. Unlike H2O2, excess oxidant can be easily removed by the addition of S2O3(2-). The I3-(-)S2O3(2-) treatment on a fortified sample of reconstituted NIST SRM 2670 freeze dried urine indicated that arsenobetaine (AsB), dimethlyarsinic acid (DMA), monomethylarsonic acid (MMA) and As(v) were not chemically degraded with recoveries ranging from 95 to 102% for all arsenicals. Sample clean-up involved pH adjustment prior to C18 filtration in order to achieve efficient As(III) conversion and quantitative recoveries of AsB and DMA. The concentrations determined in NIST SRM 2670 freeze dried urine were AsB 17.2 +/- 0.5, DMA 56 +/- 4 and MMA 10.3 +/- 0.3 with a combined total of 83 +/- 5 micrograms L-1 (+/- 2 sigma).     

Quantitative determination of three sulfonamides in environmental water samples using liquid chromatography coupled to electrospray tandem mass spectrometry

An analytical method was developed to detect the three sulfonamides para-toluenesulfonamide (p-TSA), ortho-toluenesulfonamide (o-TSA) and benzenesulfonamide (BSA) in environmental water samples at concentrations down to 0.02 microg/L using liquid chromatography coupled to tandem mass spectrometry (HPLC-MS/MS). Wastewater, surface water, groundwater and drinking water samples from Berlin (Germany) were analysed for all three compounds which appear to be ubiquitously present in the aquatic environment. p-TSA was found in high concentrations in the wastewater (<0.02-50.8 microg/L) and in groundwater below a former sewage farm (<0.02-41 microg/L), and in lower concentrations in the surface water (<0.02 to 1.15 microg/L) and drinking water (<0.02-0.27 microg/L). o-TSA and BSA were detected in considerably lower concentrations. The study makes clear that p-TSA should be monitored because of its comparatively high concentration in Berlin's drinking water.