Dielectric Relaxation Phenomena and Electric Properties of Conductive Composite Polyurethane/Polyaniline Films

Summary: Composite polyurethane/polyaniline (PU/PANI) films have been chemically prepared by oxidative in-situ polymerization of aniline inside the previously swelled PU film. Swelling kinetic studies have shown that for PU films the swelling degree of aniline is 25 wt.%. The dielectric and electrical properties of the composite films were measured using dielectric relaxation spectroscopy and four-probe method. Dielectric measurements as a function of temperature and frequency revealed the presence of a relaxation process for the composite PU/PANI-HCl film. This relaxation was explained in terms of interfacial polarization due to the double-layered structure of the composite film. The activation energy values found by dielectric and electrical measurements are close and this result confirms the conducting character of the PANI containing layer.     

静电纺丝制备Tb-PEG+Eu-PEG/PANI/PAN荧光导电相变三功能复合纤维

以聚丙烯腈(PAN)为载体基质、 以铕-聚乙二醇(Eu-PEG)和铽-聚乙二醇(Tb-PEG)为相变荧光材料, 加入掺杂的导电聚苯胺(PANI), 采用静电纺丝技术制得Tb-PEG+Eu-PEG/PANI/PAN复合纤维. 采用扫描电子显微镜(SEM)、 荧光光谱(FL) 仪、 差示扫描量热(DSC)仪及宽频介电松驰谱(BDS)仪等方法对相变荧光导电复合纤维的性能进行分析. 研究结果表明, 复合纤维具备良好的荧光、 相变及导电性能. 在294 nm紫外光激发下, 通过调节Tb-PEG和Eu-PEG的质量比可调节复合纤维的发光强度和颜色, 同时复合纤维的相变温度在5467 ℃之间. 复合纤维的电导率达到10^-6 S/cm, 随着PANI含量的增加, 电导率和介电常数增加. 通过调节Tb-PEG, Eu-PEG和PANI的比例及PEG的分子量, 可以实现复合纤维荧光、 导电及相变性能的可控调整.     

气致驱动聚苯胺/聚氨酯双层薄膜的制备与表征

以电纺聚氨酯（PU）纤维膜为基底,用滴涂聚苯胺（PANI）的方法,制备了具有不对称结构的PANI/PU双层薄膜气致驱动器。研究发现,在氯化氢气体的诱导下,该PANI/PU双层膜表现出弯曲-恢复的形变行为,这与氯化氢对聚苯胺的吸/脱附及掺杂/脱掺杂有关。此外,对驱动器承重的研究表明,PANI/PU双层人工智能肌肉可承重其自身重量的9倍以上,显示出良好的承重能力。该气致驱动器制备方法简单,其气体响应的驱动行为易于操作,具有重要的技术应用前景。     

溶剂散逸自组装法制备具有电致收缩性能的聚苯胺/聚氨酯凹透镜阵列

以水珠为模板,采用溶剂散逸自组装法制备了表面具有特殊形貌的有序多孔膜. 以此多孔膜为模板制备了聚苯胺/聚氨酯（PANI/PU）的凹透镜阵列. 采用红外光谱（FTIR）和扫描电子显微镜（SEM）对界面聚合得到的PANI/PU纳米复合物的结构和凹透镜阵列的形貌进行了表征,研究了不同合成条件对纳米复合物导电性能的影响,并对PANI/PU凹透镜阵列的电学和光学性能进行了研究. 结果表明,PANI/PU凹透镜阵列同时具有导电性、电致收缩性和光衍射性质;其收缩率与外加电压成反比,而透光率与收缩率成正比.     

Synthesis of composite of ZnO spheres with polyaniline and their microwave absorption properties

Three-dimensional (3D) ZnO microspheres with the composite of polyaniline (PANI) have been successfully synthesized by one-pot solvothermal and in-suit polymerization method. The obtained microspheres were uniform having the diameter of 4 μm–7 μm. These microspheres, inside cushion of PANI polymer, exhibit excellent microwave absorption properties. Composite of ZnO microspheres with PANI increased the complex permeability and enhanced the dielectric loss. Thus, the microwave absorption properties of the composite have been intensified. Despite the fact that the composite of ZnO with PANI herein dissipate the microwaves by dielectric loss, their performance is admirable compared to most of PANI-based composites reported. The morphological, structural and spectral properties have been investigated using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and the Fourier transform infrared (FT-IR). It is found that the maximum reflection loss value of [email protected] reaches ?41 dB at 14 GHz with a thickness of 3.5 mm that is superior to the previously reported composite of PANI with other materials.     

Electrorheological characteristics of polyaniline/titanate composite nanotube suspensions

In this paper, one-dimensional polyaniline/titanate (PANI/TN) composite nanotubes were synthesized by in situ chemical oxidative polymerization directed by block copolymer. These novel nanocomposite particles were used as a dispersed phase in electrorheological (ER) fluids, and the ER properties were investigated under both steady and dynamic shear. It was found that the ER activity of PANI/TN fluids varied with the ratio of aniline to titanate, and the PANI/TN suspensions showed a higher ER effect than that made by sphere-like PANI/TiO₂ nanoparticles. These observations were well interpreted by their dielectric spectra analysis; a larger dielectric loss enhancement and a faster rate of interfacial polarization were responsible for a higher ER activity of nanotubular PANI/TN-based fluids.     

静电纺丝制备荧光导电双功能复合纳米纤维及其表征

采用静电纺丝技术将导电聚苯胺(PANI)和铕/铽稀土配合物掺杂到高分子基质聚乙烯吡咯烷酮(PVP)中,制备出荧光导电复合纳米纤维。用扫描电镜(SEM)、荧光光谱仪(FL)、宽频介电松驰谱仪对荧光导电复合纳米纤维的性能进行分析,结果显示,在270nm紫外光激发下,铕系列与铽系列复合纳米纤维分别发出红光和绿光。同时,复合纳米纤维的电导率可以达到1.18×10~(-6) S/cm,两种复合纳米纤维同时具有优异的荧光性能及良好的导电功能。     

Polyaniline-coated coconut fibers: Structure,properties and their use as conductive additives in matrix of polyurethane derived from castor oil

Electrically conducting fibers based on coconut fibers (CF) and polyaniline (PANI) were prepared through in situ oxidative polymerization of aniline (ANI) in the presence of CF using iron (III) chloride hexahydrate (FeCl_3.6H₂O) or ammonium persulfate (APS) as an oxidant. The PANI-coated coconut fibers (CF-PANI) displayed various morphologies, electrical conductivities and percentages of PANI on the CF surface. For both systems, a PANI conductive layer was present on the CF surface, which was responsible for an electrical conductivity of around 1.5 × 10⁻¹ and 1.9 × 10⁻² S cm⁻¹ for composites prepared with FeCl₃.6H₂O and APS, respectively; values that are similar to that of pure PANI. In order to modify the structure and properties of polyurethane derived from castor oil (PU) both CF-PANI and pure PANI were used as conductive additives. The PU/CF-PANI composites exhibited higher electrical conductivity than pure PU and PU/PANI blends. Additionally, the PU/CF-PANI composites showed a variation in electrical resistivity according to the compressive stress applied, indicating that these materials could be applied for pressure-sensitive applications.     

静电纺丝制备Eu(BA)3phen/PANI/PVP光电双功能复合纳米纤维及其性能

采用静电纺丝技术将聚苯胺(PANI)和稀土配合物Eu(BA)3phen掺杂到高分子材料聚乙烯吡咯烷酮(PVP)中, 制备出新型的具有光电双功能的Eu(BA)3phen/PANI/PVP复合纳米纤维. 采用扫描电子显微镜、 X射线能量色散谱仪、 荧光光谱仪及宽频介电松弛谱仪对样品进行了表征. 实验结果表明, 复合纳米纤维直径为(270±31) nm. 在275 nm紫外光激发下, Eu(BA)3phen/PANI/PVP复合纳米纤维发射出主峰位于580, 594和617 nm的红光, 对应于Eu3+的 5D0→7F0, 5D0→7F1和5D0→7F2跃迁. 当m[Eu(BA)3phen]:m(PANI):m(PVP)=15:10:100 时, 复合纳米纤维的荧光发射最强. 复合纤维的电导率随PANI含量的增大而升高. 在m(PANI):m(PVP)=50:100时, 其电导率在高频(106 Hz)下达到1.5×10-6 S/cm.     

Polyurethane/polyaniline and polyurethane‐poly(methyl methacrylate)/polyaniline conductive core‐shell particles: Preparation,morphology, and conductivity

Polyurethane/polyaniline (PU/PANI) and polyurethane‐poly(methyl methacrylate)/polyaniline (PU‐PMMA/PANI) conductive core‐shell particles were synthesized by a two‐stage polymerization process. The first stage was to produce a core of PU or PU‐PMMA via miniemulsion polymerization using sodium dodecyl sulfate (SDS) as the surfactant. The second stage was to synthesize the shell of polyaniline over the surface of core particles. Hydrogen chloride (HCl) and dodecyl benzenesulfonic acid (DBSA) were used as the dopant agents. Ammonium persulfate (APS) was used as the oxidant for the polymerization of ANI. Different concentrations of HCl, DBSA, and SDS would cause different conformations of PANI chains and thus different morphologies of PANI particles. UV–visible spectra revealed that the polaron band was blue‐shifted because of the more coiled conformation of PANI chains by increasing the concentration of DBSA. Besides, with a high concentration of DBSA, both spherical‐ and rod‐shape PANI particles were observed by transmission electron microscope, and the coverage of PANI particles onto the core surfaces was improved. The key point of formation of rod‐type PANI particles was that DBSA was served with a high concentration accompanied with the existence of HCl or SDS. The better coverage of PANI particles over the core surfaces by charging higher DBSA concentrations resulted in a higher conductivity of hybrid particles. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3902–3911, 2007     

静电纺丝技术制备Tb（BA）3phen/PANI/PVP光电双功能复合纳米纤维

采用静电纺丝技术将聚苯胺(PANI)和稀土配合物[Tb(BA)3phen]掺杂到高分子材料(PVP)中,制备出一类新型的具有光电双功能的Tb(BA)3phen/PANI/PVP复合纳米纤维.用扫描电子显微镜(SEM)、X射线能量色散谱仪(EDS)、荧光光谱仪及宽频介电松弛谱仪对样品进行了表征.结果表明,复合纳米纤维直径为(331±43)nm.在276 nm紫外光激发下,Tb(BA)3phen/PANI/PVP复合纳米纤维发射出主峰位于491,547和585 nm的绿光,对应Tb3+的5D4→7F6,5D4→7F5和5D4→7F4跃迁.当Tb(BA)3phen∶PANI∶PVP的质量比为15∶10∶100时,复合纳米纤维的荧光发射最强,其电导率随PANI含量的增大而升高,在PANI∶PVP为50%(wt%)时,其电导率在高频(106Hz)下达1.531×10-6S/cm.     

The preparation and performance of flocculent polyaniline/carbon nanotubes composite electrode material for supercapacitors

Polyaniline (PANI)/carbon nanotubes (CNTs) composite electrode material was prepared by in situ chemical polymerization. The structure and morphology of PANI/CNTs composite are characterized by Fourier infrared spectroscopy, scanning electron microscope, and transmission electron microscopy. It has been found that a flocculent PANI was uniformly deposited on the surface of CNTs. The supercapacitive behaviors of the PANI/CNTs composite materials are investigated with cyclic voltammetry, galvanostatic charge/discharge, impedance, and cycle life measurements. The results show that the PANI/CNTs composite electrodes have higher specific capacitances than CNT electrodes and better stability than the conducting polymers. The capacitance of PANI/CNTs composite electrode is as high as 837.6 F g⁻¹ measured by cyclic voltammetry at 1 mV s⁻¹. Besides, the capacitance retention of coin supercapacitors remained 68.0% after 3,000 cycles.     

Effect of cellulose nanofibers on induced polymerization of aniline and formation of nanostructured conducting composite

Cellulose nanofibers (CNFs), derived from the most abundant and renewable biopolymer, are known as natural one-dimensional nanomaterials because of their high aspect ratio. CNFs also are rich in hydroxyl groups, offering opportunities for functionalization toward development of high-value nanostructured composites. Herein, CNFs were extracted from poplar wood powder by chemical pretreatment combined with high-intensity ultrasonication, and then coated with polyaniline (PANI) through in situ polymerization. The PANI-coated CNFs formed nanostructured frameworks around PANI, thereby conferring the CNF/PANI composite with stability and higher charge transport. The optimum PANI content to achieve maximum conductivity of CNF/PANI composites was determined. The morphology, crystall structure, chemical composition, and conductivity of the samples were characterized by transmission electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and four-point probe method, respectivily. Our results demonstrated that CNFs can be effective as a template for a flexible and stable conducting polymer to form higher-order nanostructures.     

Electrical transport properties of an organic semiconductor on polyaniline doped by boric acid

The electrical conductivity, thermoelectric power, and dielectric properties of polyaniline doped by boric acid (PANI‐B) have been investigated. The room temperature electrical conductivity of PANI‐B was found to be 1.02 × 10^?4 S cm^?1. The thermoelectric power factor for the polymer was found to be 0.64 µW m^?1 K^?2. The optical band gap of the PANI‐B was determined by optical absorption method, and the PANI‐B has a direct optical band gap of 3.71 eV. The alternating charge transport mechanism of the polymer is based on the correlated barrier hopping (CBH) model. The imaginary part of the dielectric modulus for the PANI‐B suggests a temperature dependent dielectric relaxation mechanism. Electrical conductivity and thermoelectric power results indicate that the PANI‐B is an organic semiconductor with thermally activated conduction mechanism. Copyright © 2008 John Wiley & Sons, Ltd.     

Thermomechanical behaviors and dielectric properties of polyaniline‐doped para‐toluene sulfonic acid/epoxy resin composites

Composites based on conductive organic/inorganic fillers dispersed in insulating matrix have been widely investigated because of their widespread applications such as electromagnetic shielding, electrostatic discharge, and sensors. In this context, novel composite materials based on epoxy resin matrix charged with polyaniline (PANI)‐doped para‐toluene sulfonic acid were elaborated. Fourier transform infrared spectroscopy, X‐ray diffraction and scanning electron microscopy were used to check the structure and the morphology of the samples. Viscoelastic behavior and thermal stability of the composites were explored by dynamic mechanical thermal analysis and thermogravimetric analysis. It was shown that the PANI particles exhibited a partial crystalline structure and were homogeneously dispersed in epoxy matrix. Consequently, this structure affected the thermal stability and viscoelastic properties of the composites. Furthermore, the dielectric and electrical properties were investigated up to 1 MHz. Measurements of dielectric properties revealed that with loading fillers in matrix, the dielectric parameters increased to high values at low frequency then decreased at values around 40 and 32 of real and imaginary parts, respectively, at 1 MHz with 15% of PANI content. Copyright © 2011 John Wiley & Sons, Ltd.     

一步法合成聚苯胺/十二烷基苯磺酸钠超疏水复合材料

在阴离子表面活性剂十二烷基苯磺酸钠(SDBS)体系中,采用一步法制得聚苯胺/SDBS超疏水复合材料.利用场发射扫描电子显微镜(FESEM)观察产物形貌并测定其元素组成.通过傅里叶变换红外光谱仪、紫外-可见光谱仪、X射线衍射等对其结构进行表征,用视频接触角测量仪测定材料的亲疏水性.考察SDBS浓度和溶液酸度对产物形貌及疏水性能的影响,探讨疏水机理.结果表明:在pH=1-9,SDBS浓度大于0.016 mol?L-1条件下,所制备复合材料的水接触角大于150°,SDBS掺杂使得苯胺单体的转化率高达98%.两亲分子SDBS亲水磺酸基与聚苯胺主链上的亚胺基不仅存在静电引力,而且能形成磺酰胺键,聚苯胺主链间又以氢键相互连接,SDBS分子的疏水烃基有序排列朝向聚苯胺主链外侧,从而组装形成具有微纳结构的聚苯胺/SDBS超疏水复合材料.本文结果有利于更好地理解聚苯胺/SDBS超疏水性复合材料的形成机理,对超疏水材料的设计提供新思路.     

Development of an optical ammonia sensor based on polyaniline/epoxy resin (SU-8) composite

Polyaniline (PANI)/glycidyl ether of bisphenol A (SU-8) composite film is elaborated in order to detect ammonia gas. These composite films are characterized by ultraviolet-visible (UV-vis) spectroscopy, Fourier transformed infrared (FTIR) spectroscopy and scanning electron microscopy (SEM). The sensitivity to ammonia is measured by optical absorption changes. The ammonia sensing properties of PANI/SU-8 composite films are studied, and then are compared to pure PANI films elaborated by chemical way. Experimental results show that the PANI/SU-8 optical sensor has simultaneously a rapid response to ammonia gas and regenerates easily, that is advantageous compared to pure PANI films.     

Conductive composite of polyaniline and tungsten carbide

Conductive polyaniline/tungsten carbide (PANI/TC) composite was synthesized via polymerization of the aniline monomer by (NH₄)₂S₂O₈/H₂SO₄ oxidant system in the presence of an aqueous suspension of TC. The structure, thermal stability and conductivity of PANI/TC composite were studied and the results were also compared with the pure PANI. The results showed that there was a strong interaction between the TC particles and PANI molecular chains. The crystalline structure of TC remained undisturbed upon with interaction with PANI chains. The thermal stability of PANI/TC composite was better than that of pure PANI. The direct current conductivity values of PANI/TC composite decreased slowly as the temperature increased from 25 to 165°C and PANI/TC composite exhibited significantly higher conductivity than the pure PANI.     

TiO_2聚苯胺复合膜的光电化学

利用电化学方法制备了TiO2 聚苯胺 (PANI)复合膜 .该膜具有比TiO2 或PANI膜更宽的吸收谱区 ,并且不同于利用聚苯胺光敏化的TiO2 膜 ,表现为两者复合材料膜的性质 .扫描电镜图表明 ,TiO2 微粒不完全覆盖着PANI膜 .根据TiO2 微粒光电流谱带的阈值能可得复盖在部分氧化态聚苯胺膜上的TiO2 微粒的禁带宽度为 3.0eV .部分氧化态聚苯胺膜的光电流谱遵循Fowler定律 ( 1/2 ～hυ成线性 ) .通过Fowler图得出部分氧化态聚苯胺的绝缘母体禁带宽度为 3.33eV ,并证实该绝缘母体为还原态聚苯胺 .从Mott Schottky图得到在 0 .0 5mol/LK3Fe(CN) 6 /K4 Fe(CN) 6 溶液中 (pH =8.52 )部分氧化态聚苯胺的平带电位为 0 .13V ,掺杂浓度为 5.3× 10 18cm- 3;TiO2 PANI复合膜的平带电位为 - 0 .6 5V ,掺杂浓度为 9.1× 10 19cm- 3.解释了TiO2 PANI复合膜的光电化学过程并描绘出其能带图 .利用TiO2 PANI复合膜能够有效地光降解苯酚溶液 .     

A kinetic analysis of thermal decomposition of polyaniline/ZrO<Subscript>2</Subscript> composite

Synthesis, characterization and thermal analysis of polyaniline (PANI)/ZrO₂ composite and PANI was reported in our early work. In this present, the kinetic analysis of decomposition process for these two materials was performed under non-isothermal conditions. The activation energies were calculated through Friedman and Ozawa-Flynn-Wall methods, and the possible kinetic model functions have been estimated through the multiple linear regression method. The results show that the kinetic models for the decomposition process of PANI/ZrO₂ composite and PANI are all D₃, and the corresponding function is ƒ(α)=1.5(1−α)^2/3[1−(1-α)^1/3]−1. The correlated kinetic parameters are E _a=112.7±9.2 kJ mol⁻¹, lnA=13.9 and E _a=81.8±5.6 kJ mol⁻¹, lnA=8.8 for PANI/ZrO₂ composite and PANI, respectively.