Fabrication of a high sensitive glycine electrochemical sensor based on immobilization of nanostructured Ni chelidamic acid and bimetallic Au-Pt inorganic-organic hybrid nanocomposite onto glassy carbon modified electrode

In this research a novel nickel complex was used as electrocatalyst for electrooxidation of glycine. A nano-structured nickel chelidamic acid was electrodeposited on a bimetallic Au-Pt inorganic-organic hybrid nanocomposite modified electrode. The electrode possesses a three-dimensional (3D) porous network nanoarchitecture, in which the bimetallic Au-Pt NPs serving as metal nanoparticle based microelectrode ensembles are distributed in the matrix of interlaced 3,3′,5,5′-tetramethylbenzidine (TMB) organic nanofibers (NFs). Electrocatalytic oxidation of glycine on the surface of modified electrode was investigated with cyclic voltammetry method and the results showed that the nickel chelidamic acid films displayed excellent electrochemical catalytic activities towards glycine oxidation. The hydrodynamic amperometry at rotating modified electrode at constant potential versus reference electrode was used for detection of glycine. Under optimized conditions the calibration plots are linear in the concentration range 1 μM-0.75 mM and detection limit was found to be 0.3 μM.     

Electrochemical behavior of electrodeposited rutin film on a multi-wall carbon nanotubes modified glassy carbon electrode. Improvement of the electrochemical reversibility and its application as a hydrazine sensor

By immobilizing rutin at the surface of a glassy carbon electrode (GCE) modified with multi-wall carbon nanotubes (MWCNT), a new modified electrode has been fabricated and its electrochemical behavior was investigated by cyclic voltammetry. Cyclic voltammograms of the resulting modified electrode show stable and a well defined redox couple with surface confined characteristics. The results show that the reversibility of rutin is significantly improved at a MWCNT modified GCE in comparison with GCE alone. The charge transfer coefficient, α, was calculated to be 0.4, and charge transfer rate constant, k_s, was 46.7 s⁻¹ in pH 8, indicating great facilitation of the electron transfer between rutin and MWCNT deposited on the electrode surface. The rutin MWCNT (RMWCNT) modified GCE showed excellent mediation of hydrazine oxidation: a decrease in the overvoltage of hydrazine electrooxidation was observed as well as a dramatic increase in the peak current compared to that seen at a rutin modified GCE (RMGCE), activated GCE or bare GCE. Hydrazine was determined amperometrically at the surface of RMWCNT modified GCE in pH 8. Under the optimized conditions the calibration curve is linear in the concentration range 2.0–190.0 μM hydrazine. The detection limit and sensitivity are 0.61 μM and 0.0656 μA μM⁻¹, respectively. Finally the kinetic parameters of the electron transfer coefficient, α, the heterogeneous rate constant of dependent to different potentials, k′(E), and the standard heterogeneous rate constant, k⁰, for oxidation of hydrazine at the RMWCNT surface were determined using various electrochemical methods. The advantages of this modified electrode for hydrazine determination are high sensitivity, excellent catalytic activity, short response time, wide linear range, and high exchange current density.     

Electrochemistry and electrocatalytic activity of catechin film on a glassy carbon electrode toward the oxidation of hydrazine

A very stable electroactive film of catechin was electrochemically deposited on the surface of activated glassy carbon electrode. The electrochemical behavior of catechin modified glassy carbon electrode (CMGCE) was extensively studied using cyclic voltammetry. The properties of the electrodeposited films, during preparation under different conditions, and the stability of the deposited film were examined. The charge transfer coefficient (α) and charge transfer rate constant (k _s) for catechin deposited film were calculated. It was found that the modified electrode exhibited excellent electrocatalytic activity toward hydrazine oxidation and it also showed a very large decrease in the overpotential for the oxidation of hydrazine. The CMGCE was employed to study electrocatalytic oxidation of hydrazine using cyclic voltammetry, rotating disk voltammetry, chronoamperometry, amperometry and square-wave voltammetry as diagnostic techniques. The catalytic rate constant of the modified electrode for the oxidation of hydrazine was determined by cyclic voltammetry, chronoamperometry and rotating disk voltammetry and was found to be around 10⁻³ cm s⁻¹ . In the used different voltammetric methods, the plot of the electrocatalytic current versus hydrazine concentration is constituted of two linear segments with different ranges of hydrazine concentration. Furthermore, amperometry in stirred solution exhibits a detection limit of 0.165 μM and the precision of 4.7% for replicate measurements of 40.0 μM solution of hydrazine.     

An amperometric sensor for hydrazine based on nano-copper oxide modified electrode

A sensitive hydrazine sensor has been fabricated using copper oxide nanoparticles modified glassy carbon electrode (GCE) to form nano-copper oxide/GCE. The nano-copper oxide was electrodeposited on the surface of GCE in CuCl₂ solution at −0.4 V and was characterized by Scanning electron microscopy and X-ray diffraction. The prepared modified electrode showed a good electrocatalytic activity toward oxidation of hydrazine. The electrochemical behavior of hydrazine on nano-copper oxide/GCE was explored. The oxidative current increased linearly with improving concentration of hydrazine on nano-copper oxide/GCE from 0.1 to 600 μM and detection limit for hydrazine was evaluated to be 0.03 μM at a signal-to-noise ratio of 3. The oxidation mechanism of hydrazine on the nano-copper oxide/GCE was also discussed. The fabricated sensor could be used to determine hydrazine in real water.     

Voltammetric determination of thiocytosine based on its electrocatalytic oxidation on the surface of carbon-paste electrode modified with cobalt Schiff base complexes

The electrochemical oxidation of thiocytosine on the surface of carbon-paste electrode modified with Schiff base (salophen derivatives) complexes of cobalt is studied. The effect of the substituents in the structure of salophen on the catalytic property of the modified electrode is investigated by using cyclic and differential pulse voltammetry. Cobalt (II)-5-nitrosalophen, because of its electrophilic functional groups, leads to a considerable enhancement in the catalytic activity, sensitivity (peak current), and a marked increase in the anodic potential of the modified electrode. The differential pulse voltammetry is applied as a very sensitive method for the detection of thiocytosine. The linear dynamic range was between 1 × 10⁻³ to 4 × 10⁻⁶ M with a slope of 0.0168 μA/μM, and the detection limit was 1 × 10⁻⁶ M. The modified electrode is successfully applied for the voltammetric detection of thiocytosine in human synthetic serum sample and also pharmaceutical preparations. A linear range from 1 × 10⁻³ to 1 × 10⁻⁵ M with a slope of 0.0175 μA/μM is resulted for the standard addition of thiocytosine spiked to the buffered human serum, which is differing from the curve in buffer solution about 4%. The electrode has a very good reproducibility (relative standard deviation for the slope of the calibration curve is less than 3.5% based on six determinations in a month), high stability in its voltammetric response and low detection limit for thiocytosine, and high electrochemical sensitivity with respect to other biological thiols such as cysteine.     

A selective determination of norepinephrine on the glassy carbon electrode modified with poly(ethylenedioxypyrrole dicarboxylic acid) nanofibers

A glassy carbon electrode modified with poly(3,4-ethylenedioxypyrrole-2,5-dicarboxylic acid) nanofibers (PEDOPA-NFs) was prepared for the determination of norepinephrine (NE) in phosphate buffer saline. The modified electrode demonstrated an improved sensitivity and selectivity toward the electrochemical detection of NE and could detect separately ascorbic acid (AA), uric acid (UA), and NE in their mixture. The separations of the oxidation peak potentials of NE–AA and NE–UA were 160 and 150 mV, respectively. Meanwhile, the modified electrode showed higher sensitivity and selectivity toward NE than dopamine and epinephrine. Using differential pulse voltammetry, the oxidation peak current of NE was found to be linearly dependent on its concentration within the range of 0.3–10 μM, and the detection limit of the NE oxidation current was 0.05 μM at a signal-to-noise ratio of 3. The PEDOPA-NFs promoted the electron transfer reaction of NE, while the PEDOPA-NFs, acting as a negatively charged linker, combined with the positively charged NE to induce NE accumulation in the NFs at pH under 7.4. However, the PEDOPA-NFs restrained the electrochemical response of the negatively charged AA and UA due to the electrostatic repulsion. The result indicates that the modified electrode can be used to determine NE without interference from AA and UA and selectively in the mixture of catecholamines.     

Determination of ascorbic acid using an electrode modified with cysteine self-assembled gold-platinum nanoparticles

We report on a new type of indium tin oxide (ITO) electrode for sensing ascorbic acid (AA). The ITO film was modified with gold-platinum alloy nanoparticles (Au-Pt NPs) functionalized with a self-assembled film of L-cysteine. The Au-Pt NPs were electrodeposited on the ITO film and characterized by scanning electron microscopy, energy-dispersive X-ray spectroscopy and X-ray diffraction. A cyclic voltammetric study revealed that the electrode exhibits excellent electrocatalytic activity towards the oxidation of AA. The calibration plot for AA is linear over the concentration range from 2 to 400???M with a correlation coefficient of 0.9991. The detection limit of AA is 1???M.

Electrochemical determinations of 6-mercaptopurine on the surface of a carbon nanotube-paste electrode modified with a cobalt salophen complex

A mixture of multi-walled carbon nanotube/graphite paste electrode modified with a salophen complex of cobalt was prepared and was applied for the study of the electrochemical behavior of 6-mercaptopurine (MP) using cyclic and differential pulse voltammetry (DPV). An excellent electrocatalytic activity toward the oxidation of MP was achieved, which led to a considerable lowering in the anodic overpotential and remarkable increase in the response sensitivity in comparison with unmodified electrode. Utilizing DPV method, a linear dynamic range of 1–100 μM with detection limit of 0.1 μM was obtained in phosphate buffer of pH 3.0. The electrochemical detection system was very stable, and the reproducibility of the electrode response, based on the six measurements during 1 month, was less than 3.0% for the slope of the calibration curves of MP. The electrochemical method as a simple, sensitive, and selective method was developed for the determination of MP in pharmaceutical dosage form and human plasma without any treatments.     

Electrochemical preparation, characterization, and electrocatalytic studies of Nafion–ruthenium oxide modified glassy carbon electrode

Electrochemical synthesis of ruthenium oxide (RuOx) onto Nafion-coated glassy carbon (GC) electrode and naked GC electrode were carried out by using cyclic voltammetry. Electrochemical deposition of RuOx onto Nafion-coated electrode was monitored by in situ electrochemical quartz crystal microbalance (EQCM). Surface characterizations were performed by scanning electron microscope (SEM) and atomic force microscope (AFM). SEM and AFM images revealed that ruthenium oxide particles incorporated onto the Nafion polymer film. In addition, a GC electrode modified with ruthenium oxide–Nafion film (RuOx–Nf–GC) was shown excellent electrocatalytic activity towards dopamine (DA) and ascorbic acid (AA). The anodic peak current increases linearly over the concentration range of 50 μM–1.1 mM for DA with the correlation coefficient of 0.999, and the detection limit was found to be (S/N = 3) 5 μM. Owing to the catalytic effect of the modified film towards DA, the modified electrode resolved the overlapped voltammetric responses of AA and DA into two well-defined voltammetric peaks with peak-to-peak separation about 300 mV. Here, RuOx–Nf–GC electrode employed for determination of DA in the presence of AA. This modified electrode showed good stability and antifouling properties.     

Preparation of cobalt hydroxide film modified electrode and its analytical application

Cobalt hydroxide film modified electrode was prepared by depositing cobalt hydroxide on glassy carbon electrode (GCE) surface in an alkaline aqueous solution and then characterized by cyclic voltammetry. The electrochemical behavior of resorcin on the film modified electrode was investigated. The results show that cobalt hydroxide films in alkaline solutions have good electrocatalytical activity towards the oxidation of resorcin. The recovery of resorcin from sample ranged from 95.2 to 103.4% and the oxidation peak currents were directly proportional to the resorcin concentration from 5.0 × 10⁻⁶ to 1.05 × 10⁻⁴ M with correlation coefficient of 0.9986. A detection limit of 1.0 × 10⁻⁷ M for resorcin was estimated. Various factors affecting the electrocatalytical activity of cobalt hydroxide film were investigated in detail. Real water samples were analyzed and satisfactory results were obtained.     

Development of a voltammetric procedure for assay of thebaine at a multi-walled carbon nanotubes electrode: quantification and electrochemical studies

The study of electrochemical behavior and determination of thebaine (THEB), an opiate alkaloid, is described on a multi-walled carbon nanotube (MWCNT) modified glassy carbon electrode by adsorptive stripping voltammetry and electrochemical impedance spectroscopy. The results indicated that MWCNT electrodes remarkably enhance electrocatalytic activity toward the oxidation of THEB in a wide pH range of 2.0–10.0, and it shows two irreversible and diffusion-controlled anodic peaks. Then, a sensitive, simple, and time-saving cyclic voltammetric procedure was developed for the analysis of THEB in human urine samples. Under optimized conditions, the oxidation peak has two linear dynamic ranges of 1.0–80.0 and 100.0–600.0 μM, with detection limit of 0.23 μM and a precision of <4% (relative standard deviation for eight analysis).     

Electrochemical preparation of composite of poly brilliant cresyl blue (PBCB)–poly 5-amino-2-napthalenesulfonic acid electrode and electrocatalytic application

Poly brilliant cresyl blue (PBCB) and poly 5-amino-2-napthalenesulfonic (PANS) polymer composite modified electrode was fabricated by the electrochemical polymerization of brilliant cresyl blue and 5-amino-2-napthalenesulfonic acid. When compared polymer composite electrodes with PBCB and PANS electrode, it showed enhanced electrochemical property. The morphology of the resulting composite electrode was characterized by AFM, and the electrochemical properties of the modified electrode were characterized by cyclic voltammetry and amperometry. The composite electrode showed surface-confined and pH-dependent electrochemical property. The composite electrode exhibited high catalytic behavior toward the reduction of hydrogen peroxide at low overpotential. The detection limit and sensitivity of the electrode toward H₂O₂ detection was 5 μM and 1 μA/mM, respectively, and response time was less than 10 s for hydrogen peroxide.     

Sensitive amperometric detection of omeprazole and pantoperazole at electrodeposited nickel oxide nanoparticles modified glassy carbon electrode

Glassy carbon electrode modified with electrodeposited nickel oxide nanoparticles (NiOxNPs) was used as electrocatalyst for oxidation of omeprazole and pentoperazole in alkaline solution. The modified electrode exhibited efficient electrocatalytic activity for the oxidation of omeprazole and pentoperazole with relatively high sensitivity, excellent stability, and long lifetime. Hydrodynamic amperometric method is used for determination of selected analytes. Under optimized condition, the linear concentration range, detection limit, and sensitivity of modified electrode toward omeprazole detection are 4.5–120 μM, 0.4 μM (at signal to noise 3), and 40.1 nA μM⁻¹ cm⁻², respectively. For pantoperazole, hydrodynamic amperometric determination yielded calibration curve with linear range of 2.5–180 μM, detection limit of 0.2 μM, and sensitivity of 39.2 nA μM⁻¹ cm⁻², respectively. The proposed method was successfully applied to pentoperazole and omeprazole determination in drug samples.     

LaNi<Subscript>0.5</Subscript>Ti<Subscript>0.5</Subscript>O<Subscript>3</Subscript>/CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>-based sensor for sensitive determination of paracetamol

A novel electrochemical sensor based on LaNi_0.5Ti_0.5O₃/CoFe₂O₄ nanoparticle-modified electrode (LNT–CFO/GCE) for sensitive determination of paracetamol (PAR) was presented. Experimental conditions such as the concentration of LNT–CFO, pH value, and applied potential were investigated. Under the optimum conditions, the electrochemical performances of LNT–CFO/GCE have been researched on the oxidation of PAR. The electrochemical behaviors of PAR on LNT–CFO/GCE were investigated by cyclic voltammetry. The results showed that LNT–CFO/GCE exhibited excellent promotion to the oxidation of PAR. The over-potential of PAR decreased significantly on the modified electrode compared with that on bare GCE. Furthermore, the sensor exhibits good reproducibility, stability, and selectivity in PAR determination. Linear response was obtained in the range of 0.5 to 901 μM with a detection limit of 0.19 μM for PAR.     

Carbon paste electrode modified by cobalt ions dispersed into poly (N-methylaniline) preparing in the presence of SDS: application in electrocatalytic oxidation of hydrogen peroxide

Conducting and stable poly (N-methylaniline) film was prepared by using the repeated potential cycling technique in aqueous solution containing N-methylaniline, sulfuric acid, and sodium dodecyl sulfate (SDS) at the surface of carbon paste electrode (CPE). The transition metal ions of Co(ІІ) were incorporated to the polymer by immersion of the modified electrode in 0.1 M cobalt chloride solution for 10 min. The electrochemical characterization of this modified electrode exhibits stable redox behavior of Co(ІІ)→Co(ІІІ) and formation of insoluble oxide/hydroxide cobalt species on the CPE surface. The modified electrode showed well-defined and stable redox couples in alkaline aqueous solution. The modified electrode showed excellent electrocatalytic activity for oxidation of hydrogen peroxide. The response of modified electrode toward the H₂O₂ oxidation was examined using cyclic voltammetry, differential pulse voltammetry, square wave voltammetry, and chronoamperometry. This modified electrode has many advantages such as simple preparation procedure, good reproducibility, and high catalytic activity toward the hydrogen peroxide oxidation. Such characteristics were explored for the specific determination of hydrogen peroxide in cosmetics product sample, giving results in excellent agreement with those obtained by standard method.     

Poly(3,4-ethylenedioxythiophene-co-(5-amino-2-naphthalenesulfonic acid)) (PEDOT-PANS) film modified glassy carbon electrode for selective detection of dopamine in the presence of ascorbic acid and uric acid

Poly(3,4-ethylenedioxythiophene-co-(5-amino-2-naphthalenesulfonic acid)) (PEDOT-PANS) film modified glassy carbon electrode was prepared by electrochemical polymerization technique. The properties of modified electrode was studied. It was found that the electrochemical properties of modified electrode was very much dependent on the experimental conditions, such as monomer oxidation potential and pH. The modified electrode surface was characterized by scanning electron microscopy (SEM). The PEDOT-PANS film modified electrode shows electrocatalytic activity toward oxidation of dopamine (DA) in acetate buffer solution (pH 5.0) and results in a marked enhancement of the current response. The linear sweep voltammetric (LSV) peak heights are linear with DA concentration from 2 × 10⁻⁶ to 1 × 10⁻⁵ M. The detection limit is 5 × 10⁻⁷ M. More over, the interferences of ascorbic acid (AA) and uric acid (UA) were effectively diminished. This work provides a simple and easy approach for selective determination of dopamine in the presence of ascorbic acid and uric acid.     

Covalent Modification of Glassy Carbon Electrode with L-Cysteine for the Determination of Acetaminophen

A novel L-cysteine film modified electrode has been fabricated by means of an electrochemical oxidation procedure, and it was successfully applied to the electrochemical determination of acetaminophen. This method utilizes the electrooxidation of amines to their analogous cation radicals to form a chemically stable covalent linkage between the nitrogen atom of the amine and edge plane sites at the glassy carbon electrode surface. The electrochemical behaviour of acetaminophen at the film electrode was investigated in 0.1 mol L⁻¹ phosphate buffer (pH 6.20). It was found that the redox peak current of acetaminophen was enhanced greatly on the film electrode. Linearity between the oxidation peak current and the acetaminophen concentration was obtained in the range of 1.0 × 10⁻⁴–2.0 × 10⁻⁷ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁸ mol L⁻¹. For seven parallel detections of 1.0 × 10⁻⁵ mol L⁻¹ acetaminophen, the relative standard deviation (RSD) was 1.46%, suggesting that the film electrode has excellent reproducibility. Application to the determination of acetaminophen in drug tablets and human urine demonstrated that the film electrode has good stability and high sensitivity.     

Functionalization of platinum nanoparticles for electrochemical detection of nitrite

In this work, a novel electrochemical method for nitrite detection by using functionalized platinum nanoparticles (PtNPs) is proposed. Firstly, a gold electrode is immobilized with 4-(2-aminoethyl)benzenamine. Then, PtNPs are modified with 5-[1, 2]dithiolan-3-yl-pentanoic acid [2-(naphthalene-1-ylamino)-ethyl]amide (DPAN). Consequently, in the presence of nitrite ions, Griess reaction occurs between 4-(2-aminoethyl)benzenamine on the electrode and DPAN on PtNPs, thus PtNPs are localized onto the electrode surface. So, PtNPs-electrocatalyzed reduction of H₂O₂ can be achieved to correlate the electrochemical signal with the concentration of nitrite ions. The linear concentration range can be as wide as 10–1,000 μM, while the detection limit is as low as 5 μM. The proposed method has been also successfully applied to the detection of nitrite with the local lake water, and the result is well consistent with that obtained by UV-visible spectrophotometric method. So, this method has potential use for monitoring nitrite in drinking water supplies in the future.     

Flow injection amperometric sensing of uric acid and ascorbic acid using the self-assembly of heterocyclic thiol on Au electrode

Au electrode modified with the self-assembled monolayer of a heterocyclic thiol, mercaptotriazole (MTz), is used for the electroanalysis of uric acid (UA) and ascorbic acid (AA). MTz forms a less compact self-assembly on Au electrode. The self-assembly of MTz on Au electrode favors the oxidation of UA and AA at less positive potential. Significant decrease (∼400 mV) in the overpotential and enhancement in the peak current for the oxidation of interfering AA with respect to the unmodified electrode is observed. The negative shift in the oxidation peak potential of AA favors electrochemical sensing of UA without any interference. Two well-separated voltammetric peaks for AA and UA are observed in their coexistence. The large separation between the two voltammetric peaks allows the simultaneous or selective sensing of the analytes without compromising the sensitivity. Linear response is obtained for a wide concentration range. This electrode could sense as low as 1 μM of UA in the presence of 10-fold excess of interfering AA. No change in the sensitivity (0.012 μA/μM) of the electrode toward UA in the presence and absence of AA is observed. Reproducible and stable amperometric flow injection response was obtained upon repetitive injection.     

Immobilization of flavine adenine dinucleotide onto nickel oxide nanostructures modified glassy carbon electrode: fabrication of highly sensitive persulfate sensor

A simple method was used to fabricate flavin adenine dinucleotide (FAD)/NiOx nanocomposite on the surface of glassy carbon (GC) electrode. Cyclic voltammetry technique was applied for deposition nickel oxide nanostructures onto GC surface. Owing to its high biocompatibility and large surface area of nickel oxide nanomaterials with immersing the GC/NiOx-modified electrode into FAD solution for a short period of time, 10–140 s, a stable thin layer of the FAD molecules immobilized onto electrode surface. The FAD/NiOx films exhibited a pair of well-defined, stable, and nearly reversible CV peaks at wide pH range (2–10). The formal potential of adsorbed FAD onto nickel oxide nanoparticles film, E ^o′ vs. Ag/AgCl reference electrode is −0.44 V in pH 7 buffer solutions was similar to dissolved FAD and changed linearly with a slope of 58.6 mV/pH in the pH range 2–10. The surface coverage and heterogeneous electron transfer rate constant (k _s ) of FAD immobilized on NiOx film glassy carbon electrode are 4.66 × 10⁻¹¹ mol cm⁻² and 63 ± 0.1 s⁻¹, indicating the high loading ability of the nickel oxide nanoparticles and great facilitation of the electron transfer between FAD and nickel oxide nanoparticles. FAD/NiOx nanocomposite-modified GC electrode shows excellent electrocatalytic activity toward S₂O₈²⁻ reduction at reduced overpotential. Furthermore, rotated modified electrode illustrates good analytical performance for amperometric detection of S₂O₈²⁻. Under optimized condition, the concentration calibration range, detection limit, and sensitivity were 3 μM–1.5 mM, 0.38 μM and 16.6 nA/μM, respectively.