沥青基活性炭纤维复合活化工艺的研究

以沥青基炭纤维为原料，研究了用铵盐作为化学活化剂对其进行浸渍预处理，然后采用（H2O＋CO2）活化的方法制备活性炭纤维，讨论了工艺条件对活性炭纤维性能的影响并通过光电子能谱XPS探讨了活化过程中炭纤维表面官能团的变化。结果表明：采用这种物理和化学复合活化工艺，可以在较高得率下提高活性炭纤维比表面积。同时浸渍处理、H2O流量、活化温度和活化时间等工艺参数显著影响活性炭纤维的比表面积和得率，优化的工艺为：经铵盐浸渍6h，炭纤维在水蒸气与CO2流量比3：1的混合气氛中900℃活化30min。XPS研究表明，活化后炭纤维表面的含氧官能团C－O明显减少，铵盐浸渍未能增加活性炭纤维表面的含氮基团。     

过渡金属对分子筛担载Pd催化剂上CO氧化性能影响

分别采用共浸和连续浸渍法制备了一系列添加过渡金属的Pd-M-Ox-NaZSM-5(M=Cr，Mn，Fe，Co，Ni，Cu，Zn，Mo，Zr等)负载型催化剂．以CO氧化为探针反应，考察了不同制备方法对CO氧化性能影响，结果表明共浸法制备的各催化剂其活性明显优于连续浸渍法．详细考察了反应温度、Fe含量、氢气预还原、空速以及水蒸气等对共浸Pd-Fe-Ox-NaZSM-5催化剂上CO氧化行为影响，并应用XRD和XPS等手段对催化剂体相结构和表面状态进行了表征．结果表明：加入Fe2O3可明显提高Pd/NaZSM-5催化剂活性，且催化CO氧化的转化率随反应温度及Fe含量增加而增加；空速增加以及H2预还原作用导致Pd-Fe-Ox-NaZSM-5活性有所降低；催化剂对水蒸气较为敏感．XRD测试结果表明催化剂中Pd组分处于较高分散状态，以红铁矿形式存在的Fe2O3的引入，促进了Pd物种在NaZSM-5载体上的分散．表面XPS分析证实Fe2O3与Pd物种间存在较强的相互协同作用，且催化剂表面Pd物种处于较高氧化状态．Pd的高分散及其与Fe2O3的相互协同作用是共浸催化剂具有高活性的关键因素．     

多级孔La_(1-x)Sr_xCo_(1-y)Cu_yO_3的软模板法制备、表征及催化活性

分别在以P123为软模板和无P123的条件下制备8个钙钛矿型催化剂La_(1-x)Sr_xCo_(1-y)Cu_yO_3(x=0,0.1;y=0,0.2),用X射线衍射(XRD)、扫描电镜(SEM)、X射线能谱仪(EDS)、BET和X射线光电子能谱(XPS)进行了表征,并测试了它们对CO+NO反应的催化活性。结果表明,以P123为软模板制备的催化剂具有更多大孔径段的介孔和小孔径段的大孔,更大的孔容,更多的氧空位,同时表面La的偏析更少,表面Co的含量以及Co~(3+)/Co~(2+)比例更高。因而,催化剂的催化活性明显优于无模板法制备的催化剂,其中对NO转化率的提升尤为显著。Sr对La的适量取代可以促进CO的氧化反应,而Cu掺杂会降低CO和NO的转化率。     

Ni-Fe/La2O2CO3催化乙醇水蒸气重整制氢的研究

采用La2(CO3)3空气焙烧法制备了La2O2CO3载体、采用浸渍法制备了Ni,Fe不同比例的Ni-Fe双金属催化剂及Ni/La2O2CO3,Fe/La2 O2 CO3催化剂,考察了各催化剂从300～700℃催化乙醇水蒸气重整反应的性能,并用BET,XRD,TPR等技术对催化剂进行表征。结果表明,相对单一金属催化剂,Ni-Fe双金属催化剂均表现出更高的活性,这可能是因为高分散的Ni,Fe和LaFeyNi1-yO3的共存作用。其中Ni含量为10%,Fe含量为5%时的Ni-Fe/La2O2CO3表现出最高的活性,400℃时乙醇的转化率为100%,H2的选择性最高达到94.1%,而CO的选择性则低至1.2%。     

助剂对Ni/SiO_2催化剂微观结构及二硝基甲苯催化加氢性能的影响

采用等体积浸渍法制备了负载型Ni/SiO2催化剂,研究了Ce、Zr、La、Co和Fe助剂对催化剂微观结构及其催化二硝基甲苯(DNT,C6H3CH3(NO2)2)加氢制备甲苯二胺(TDA,C6H3CH3(NH2)2)性能的影响。通过XRD,BET,H2-TPD、H2-TPR和XPS技术对催化剂进行了表征。结果表明,助剂的引入促进了Ni物种在载体表面的分散,减小了Ni晶粒的尺寸,使得NiO晶粒更易还原。添加La、Fe和Zr助剂增加了有效的Ni活性中心数,有利于催化活性的提高,其中,添加La助剂制备的催化剂催化性能最优,DNT转化率和TDA选择性分别为98.1%和99.1%。但Co和Ce助剂的加入降低了化学氢吸附量,使得有效的Ni活性中心数降低,降低了催化剂的催化活性。     

活性炭二次活化对其电化学容量的影响

为进一步提高作为电化学超级电容器电极材料活性炭的电化学容量, 采用KOH作为二次活性剂, 将所得活性炭进行二次化学活化处理, 从而得到二次活化活性炭. 将原始活性炭材料与二次活化活性炭材料都分别经过系列处理, 组装成电化学超级电容器进行电化学性能测试. 测试结果表明, 二次活化活性炭材料的电化学容量达到145.0 F·g-1(有机电解液), 远远大于原活性炭材料的容量(45.0 F·g-1). 为研究二次活化活性炭材料电化学容量大幅提高的原因, 将这两种材料分别进行微观结构数据测试, 包括比表面积、N2吸脱附等温曲线和孔径分布. 研究结果表明, 二次活化处理大大增加了二次活化活性炭材料在孔径为2-3 nm的中孔分布, 从而证实对于有机电解液, 电极材料在2-3 nm的中孔对其电化学容量的提高具有重要意义.     

溶剂化金属原子浸渍法制备高分散载型催化剂 II. Fe,Co,Ni催化剂的分散度和催化性能研究

本文利用一种新的方法-溶剂化金属原子浸渍法制备了Fe/γ-Al_2O_3, Fe/SiO_2, Co/γ-Al_2O_3,Co/SiO_2, Ni/γ-Al_2O_3和Ni/SiO_2六种催化剂。H_2化学吸附, TEM和XRD测定结果表明这些催化剂中Fe, Co, Ni金属颗粒平均直径都小于3.0 nm, 金属分散度均大于50%。作者研究了Fe/γ-Al_2O_3, Co/γ-Al_2O_3和Ni/γ-Al_2O_3三种催化剂在CO+H_2反应中的催化行为, 测定了碳氢产物分布和比催化活性, 表明随着H_2/CO比增大和反应温度升高。较高分子量物种产量减少, 有利于生成甲烷。催化剂的活性大小次序为Fe>Ni>Co。     

溶剂化金属原子浸渍法制备高分散负载型催化剂——Ⅱ,Fe,Co,Ni催化剂的分散度和催化性能研究

本文利用一种新的方法-溶剂化金属原子浸渍法制备了Fe/γ-Al_2O_3,Fe/SiO_2,Co/γ-Al_2O_3,Co/SiO_2,Ni/γ-Al_2O_3和Ni/SiO_2六种催化剂。H_2化学吸附,TEM和XRD测定结果表明这些催化剂中Fe,Co,Ni金属颗粒平均直径都小于30A,金属分散度均大于50%。作者研究了Fe/γ-Al_2O_3,Co/γ-Al_2O_3和Ni/γ-Al_2O_3三种催化剂在CO+H_2反应中的催化行为,测定了碳氢产物分布和比催化活性,表明随着H_2/CO比增大和反应温度升高。较高分子量物种产量减少,有利于生成甲烷。催化剂的活性大小次序为Fe>Ni>Co。     

不同方法制备的介孔Ni/MgO催化剂上水蒸气重整苯酚制氢

利用浸渍法和水热共沉淀法两种方法,制备了介孔Ni/MgO催化剂,用于水蒸气重整生物质油模型物苯酚制取氢气;利用XRD、N2吸附/脱附、H2-TPR、TEM以及TG等手段对催化剂进行了表征。结果表明,以介孔MgO为载体,采用浸渍法制备的介孔NiO/MgO固溶体,具有较高的比表面积(60.6m2/g)以及较大的孔径(10.1nm)。与水热共沉淀法制备的催化剂相比,浸渍法制备的NiO/MgO前驱体经还原后的所得到介孔Ni/MgO催化剂Ni颗粒较小(5.0-6.0nm),分布均匀,具有较高的分散度(19.44%)。较大的比表面积能有效地促进活性金属颗粒的分散,而介孔有利于反应物和产物在催化剂孔道中的扩散。因此,该Ni/MgO催化剂在水蒸气重整苯酚制氢反应中具有较高的催化活性、稳定性和优异的抗积炭能力。     

用CO_2吸附法分析分子筛的孔结构

以NaA,NaY和NaZSM-5分子筛为研究对象,以CO2为吸附质,通过吸附数据测定,研究分子筛材料微孔结构的吸附表征方法.计算了NaA、NaY和NaZSM-5分子筛的微孔孔容,其中基于D-A方程的微孔孔容值与文献值一致.根据CO2吸附数据分析了3种分子筛的孔径分布.发现对于含有球形孔结构的NaA,NaY分子筛和NaA+NaY混合物,HK(Horvath-Kawazoe)球形模型(HKsphere)能够很好地描述其孔径分布,而HK柱状模型(HKcylinder)能够很好地表征具有柱状孔道结构的NaZSM-5分子筛.单一的HK方法不能表征同时含有柱状孔和球形孔的NaA+NaZSM-5混合物,使用HKcylinder只能得到混合物材料中柱状孔的分布情况,而使用HKsphere只能得到球形孔的分布情况.     

A New Approach for Controlling Mesoporosity in Activated Carbon by the Consecutive Process of Air Oxidation,Thermal Destruction of Surface Functional Groups,and Carbon Activation (the OTA Method)

A new and simple method, based entirely on a physical approach, was proposed to produce activated carbon from longan fruit seed with controlled mesoporosity. This method, referred to as the OTA, consisted of three consecutive steps of (1) air oxidation of initial microporous activated carbon of about 30% char burn-off to introduce oxygen surface functional groups, (2) the thermal destruction of the functional groups by heating the oxidized carbon in a nitrogen atmosphere at a high temperature to increase the surface reactivity due to increased surface defects by bond disruption, and (3) the final reactivation of the resulting carbon in carbon dioxide. The formation of mesopores was achieved through the enlargement of the original micropores after heat treatment via the CO₂ gasification, and at the same time new micropores were also produced, resulting in a larger increase in the percentage of mesopore volume and the total specific surface area, in comparison with the production of activated carbon by the conventional two-step activation method using the same activation time and temperature. For the activation temperatures of 850 and 900 °C and the activation time of up to 240 min, it was found that the porous properties of activated carbon increased with the increase in activation time and temperature for both preparation methods. A maximum volume of mesopores of 0.474 cm³/g, which accounts for 44.1% of the total pore volume, and a maximum BET surface area of 1773 m²/g was achieved using three cycles of the OTA method at the activation temperature of 850 °C and 60 min activation time for each preparation cycle. The two-step activation method yielded activated carbon with a maximum mesopore volume of 0.270 cm³/g (33.0% of total pore volume) and surface area of 1499 m²/g when the activation temperature of 900 °C and a comparable activation time of 240 min were employed. Production of activated carbon by the OTA method is superior to the two-step activation method for better and more precise control of mesopore development.     

几种植物基活性炭材料的孔结构与吸附性能比较——(I)孔结构表征

测定了3种植物基活性炭材料:椰壳活性炭 (CAC4)、剑麻茎基活性炭 (SSAC) 和剑麻基活性碳纤维 (SACF) 的氮吸附等温线,并用不同的理论方法对其孔结构进行了分析和表征。结果表明:CAC4为微孔型,孔径分布集中且大部分是0.7nm以下的极微孔;在相同条件下制备的SSAC和SACF孔分布较为相似,都呈多分散性,结构中除微孔外,还含有丰富的中孔,中孔率均超过50%以上。两者相比,SACF的中孔量和平均孔径更大。3个样品的形态特征和孔结构虽然不同,但其吸附过程都可以用微孔多段填充机理来解析。     

沥青基球状活性炭气相吸脱附行为研究

本文利用热重法研究了一系列沥青基球状活性炭对蒸汽及正已烷蒸汽的动态吸脱附曲线。结果表明,PSAC对苯蒸汽的吸附及再生性能优良。随吸附温度的降低、比表面积的增大、总孔容及微孔容的增大,PSAC对苯蒸汽的吸附容量增大。PSAC对正已烷的吸附速度大于对苯蒸汽的吸附速度,但其对正已烷的平衡吸附容量小于对苯蒸汽的平衡吸附容量。     

Synthesis of mesoporous carbons using ordered and disordered mesoporous silica templates and polyacrylonitrile as carbon precursor

Mesoporous carbons were synthesized from polyacrylonitrile (PAN) using ordered and disordered mesoporous silica templates and were characterized using transmission electron microscopy (TEM), powder X-ray diffraction, nitrogen adsorption, and thermogravimetry. The pores of the silica templates were infiltrated with carbon precursor (PAN) via polymerization of acrylonitrile from initiation sites chemically bonded to the silica surface. This polymerization method is expected to allow for a uniform filling of the template with PAN and to minimize the introduction of nontemplated PAN, thus mitigating the formation of nontemplated carbon. PAN was stabilized by heating to 573 K under air and carbonized under N2 at 1073 K. The resulting carbons exhibited high total pore volumes (1.5-1.8 cm3 g(-1)), with a primary contribution of the mesopore volume and with relatively low microporosity. The carbons synthesized using mesoporous templates with a 2-dimensional hexagonal structure (SBA-15 silica) and a face-centered cubic structure (FDU-1 silica) exhibited narrow pore size distributions (PSDs), whereas the carbon synthesized using disordered silica gel template had broader PSD. TEM showed that the SBA-15-templated carbon was composed of arrays of long, straight, or curved nanorods aligned in 2-D hexagonal arrays. The carbon replica of FDU-1 silica appeared to be composed of ordered arrays of spheres. XRD provided evidence of some degree of ordering of graphene sheets in the carbon frameworks. Elemental analysis showed that the carbons contain an appreciable amount of nitrogen. The use of our novel infiltration method and PAN as a carbon precursor allowed us to obtain ordered mesoporous carbons (OMCs) with (i) very high mesopore volume, (ii) low microporosity, (iii) low secondary mesoporosity, (iv) large pore diameter (8-12 nm), and (v) semi-graphitic framework, which represent a desirable combination of features that has not been realized before for OMCs.     

沥青基球状活性炭担载尿素用于NO2的低温选择性催化还原行为研究

将作为还原剂的尿素担载于沥青基球状活性炭(PSAC)上研究了NO₂的低温选择性催化还原(SCR)反应。结果表明,PSAC上尿素担载量的提高可以增大NO₂与尿素的反应几率;当尿素担载量由8%提高到30%时,SCR反应脱硝活性显著提高,脱硝时间相应延长。在30~90℃,升高反应温度会减小NO₂在PSAC表面的吸附量,从而导致NO_x的脱除量减小。增加反应气氛中NO₂和O₂的浓度均有利于脱硝活性的提高,但当O₂进料浓度大于9%时,继续增加O₂进料浓度对脱硝活性的改善作用变得微弱。降低空速有利于提高脱硝活性和延长脱硝时间。当反应温度为30℃、空速为2000h^-1、NO₂和O₂的进料浓度分别为0.05%和21%时,尿素担载量为8%的PSAC可在49h内实现85%以上的NO_x转化率。     

Mesoporous activated carbon from <Emphasis Type="Italic">Pentace</Emphasis> species sawdust via microwave-induced KOH activation: optimization and methylene blue adsorption

This work studied the optimization of preparation conditions of Pentace species sawdust activated carbon (PSAC) via microwave-induced KOH activation for the adsorption of methylene blue (MB) dye from aqueous solutions. The produced activated carbon was characterised through Brunauer–Emmett–Teller (BET) surface area and pore structural analysis, proximate and ultimate, scanning electron microscopy, and Fourier transform infrared spectroscopy. Response surface methodology technique was used to optimize the radiation power, radiation time and impregnation ratio for MB removal and PSAC yield through central composite design. The optimum preparation conditions for PSAC were obtained at a radiation power of 418 W, radiation time of 6.4 min, and an impregnation ratio of 0.5, which resulted in 27% PSAC yield and 93.74% MB removal. A mesoporous structure of PSAC was formed, with a BET surface area, total pore volume and average pore diameter of 914.15 m²/g, 0.52 cm³/g, and 3.19 nm, respectively. The experimental kinetic data were well described by a pseudo-second-order model and intraparticle diffusion. Adsorption data fitted the Redlich–Peterson equation better than the Langmuir, Freundlich, Temkin, Dubinin–Radushkevich and Sips equations. However, the exponential value of Redlich–Peterson approached unity, hence, resulting in the original Langmuir equation, with adsorption capacity of 357.14 mg/g. The adsorption performance was effectively preserved even after four consecutive cycles, demonstrating good regeneration ability.     

不熔化沥青球在低速流化床中炭化和活化的初步研究

不熔化沥青球在低速流化床中炭化和活化的初步研究乔文明，王克温，凌立成，刘朗周承泽，王瑾，郑斌（中国科学院山西煤炭化学研究所，太原０３０００１）（上海太平洋化工（集团）公司焦化总厂，２００２４１）关键词低速流化床，活化，炭化，球形活性炭由于球形活性炭，...     

Porosity characteristics and pore developments of various particle sizes palm kernel shells activated carbon (PKSAC) and its potential applications

The adsorption behaviour and the micro- and mesopore size distributions of commercial palm kernel shell activated carbons (PKSAC) and other commercial activated carbon are characterized. The results showed that PKSAC are predominantly microporous materials, where micropores account 68–79% of total porosity. On the other hand, commercial activated carbons: Norit SX Plus, Calgon 12×40, and Shirasagi “A” activated carbons contained high mesopore fraction ranging from 33 to 52%. The analysis showed that the degree of mesoporosity of PKSAC is increased steadily with the decrease of particle size. This is due to the presence of channels interconnect the smaller pores in the interior of smaller particle size PKSAC. The smaller size PKSAC particle that is highly mesoporous has preformed better on the adsorption of larger molecules such as methylene blue. On the other hand, bigger size PKSAC particle has better performance on the adsorption of smaller adsorbates such as iodine.     

三聚氰胺浸渍活性炭用于低温NH_3-SCR脱硝的研究

通过将三聚氰胺(M)浸渍在活性炭(AC)上制备了渗氮活性炭(ACM),研究了浸渍时间、煅烧温度等因素对ACM含氮量以及低温NH3-SCR脱硝活性的影响。结果表明,三聚氰胺浸渍后可以提高活性炭的低温脱硝活性,在80℃下ACM-5-900的NO转化率达到51.67%,而AC只有21.92%。采用BET、元素分析及XPS等分别对渗氮活性炭ACM的结构、表面含氮量以及含氮官能团分布进行分析,表明含氮官能团的存在形式而不是含氮量影响渗氮活性炭的低温脱硝活性。同时NO+O2-TPD结果表明,渗氮改性后脱硝活性提高主要是由于表面含氮官能团提高了活性炭对NO的吸附和氧化。另外,SO2的存在会抑制渗氮活性炭的低温脱硝活性。     

Study on Active Carbon-Supported Two-Component Catalysts for NO Conversion

The impregnation of active carbon with two-component aqueous solutions of Cu and Co nitrates has been investigated and different deposition degrees of copper and cobalt ions have been established. Adsorption analysis has shown modification of the active carbon texture after impregnation with solutions whose concentration of Cu and Co ions exceeds 3%. A catalyst with a high activity in the reduction of NO with CO at 100 degrees C has been obtained. All samples are found to catalyze the complete reduction of NO to N2. A correlation between the catalytic activity and the Cu:Co ratio in the supported phase has been established. Copyright 1999 Academic Press.