Effect of heat treatment on morphology, crystalline structure and photocatalysis properties of TiO2 nanotubes on Ti substrate and freestanding membrane

Highly ordered titanium oxide (TiO₂) nanotubes were prepared by electrolytic anodization of titanium electrodes. Morphological evolution and phase transformations of TiO₂ nanotubes on a Ti substrate and that of freestanding TiO₂ membranes during the calcinations process were studied by scanning electron microscopy, transmission electron microscopy, and X-ray diffraction microscopy. The detailed results and mechanisms on the morphology and crystalline structure were presented. Our results show that a compact layer exists between the tubular layer and Ti substrate at 600 °C, and the length of the nanotubes shortens dramatically at 750 °C. The freestanding membranes have many particles on their tubes during calcinations from 450 to 900 °C. The TiO₂ nanotubes on the Ti substrate transform to rutile crystals at 600 °C, while the freestanding TiO₂ membranes retain an anatase crystal with increasing temperature to 800 °C. The photocatalytic activity of TiO₂ nanotubes on a Ti substrate annealed at different temperatures was investigated by the degradation of methyl orange in aqueous solution under UV light irradiation. Due to the anatase crystals in the tubular layer and rutile crystals in the compact layer, TiO₂ nanotubes annealed at 450 °C with pure anatase crystals have a better photocatalytic activity than those annealed at 600 °C or 750 °C.     

TiO2 Wedgy Nanotubes Array Flims for Photovoltaic Enhancement

In this study, TiO₂ wedgy nanotubes with rectangular cross-sections were fabricated on transparent conductive substrates by using TiO₂ nanorods as the precursor via the anisotropic etching route. TiO2 nanotubes with V-shaped hollow structure and the special crystal plane exposed on the tube wall possess nature of high surface area for more dye molecules absorption, and the strong light scattering effects and dual-channel for effective electron transport of the TiO₂ V-shaped nanotubes based dye-sensitized solar cell exhibit a remarkable photovoltaic enhancement compared with the TiO₂ nanorods. The photoanode based on our V-shaped TiO₂ nanotubes with a length of 1.5 μm show a 123% increase of the dye loading and a 182% improvement in the overall conversion efficiency when compared with 4 μm rutile TiO₂ nanorods photoanode.     

Application of ultrasonic wave to clean the surface of the TiO2 nanotubes prepared by the electrochemical anodization

In this study, the TiO₂ nanotubes were fabricated by electrochemical anodization in a NH₄F/Na₂SO₄/PEG400/H₂O electrolyte system. Ultrasonic wave (80 W, 40 kHz) was used to clean the surface of TiO₂ nanotube arrays in the medium of water after the completion of the anodization. Surface morphology (FESEM) and X-ray diffraction spectrum of the nanotubes treated by sonication at 0 min, 9 min, 40 min and 60 min were compared. The experimental results showed that the precipitate on the surface of the nanotube arrays could be removed by the ultrasonic wave. The treating time had an influence on the precipitate removal and 9 min (corresponding to 12 Wh) is the suitable time for surface cleaning of the TiO₂ nanotubes on this experimental condition.     

Synthesis and characterization of bamboo-like CdS/TiO<Subscript>2</Subscript> nanotubes composites with enhanced visible-light photocatalytic activity

In order to efficiently use the visible light in the photocatalytic reaction, a novel bamboo-like CdS/TiO₂ nanotubes composite was prepared by a facile chemical reduction method, in which CdS nanoparticles located in the TiO₂ nanotubes. The composition and structure of this nanocomposite were characterized by TEM, HRTEM, XRD, XPS, FTIR and UV-vis spectroscopy. This CdS/TiO₂ nanotubes composite exhibited much higher visible-light photocatalytic activity for the degradation of methylene blue than pure TiO₂ nanotubes and CdS nanoparticles, and the highest photodegradation efficiency after 6 h irradiation can reach 84.5%. It is inferred that the unique structure of CdS/TiO₂ nanotubes composites acts an important role for the improvement of their photocatalytic activity.     

Preparation and photocatalytic activity of bicrystal phase TiO2 nanotubes containing TiO2-B and anatase

Bicrystal phase TiO₂ nanotubes (NTS) containing monoclinic TiO₂-B and anatase were prepared by the hydrothermal reaction of anatase nanoparticles with NaOH aqueous solution and a heat treatment. Their structure was characterized by XRD, TEM and Raman spectra. The results showed that the bicrystal phase TiO₂ NTS were formed after calcining H₂Ti₄O₉·H₂O NTS at 573 K. The bicrystal phase TiO₂ NTS exhibit significantly higher photocatalytic activity than the single phase anatase NTS and Dessuga P-25 nanoparticles in the degradation of Methyl Orange aqueous solution under ultraviolet light irradiation, which is attributed to the large surface and interface areas of the bicrystal phase TiO₂ NTS.     

Reasons for the deactivation of Pt/TiO2 photocatalyst treated by inert gas N2

The effect of N₂ treatment on the photocatalytic activity of Pt⁰/TiO₂ was investigated. The results showed that after treatment at 500 °C in N₂, 70% of the photocatalytic activity of 1.0 wt.% Pt⁰/TiO₂ was lost by the evaluation of photocatalytic oxidation reaction of C₃H₆. Transmission electron microscopy (TEM) and Ar⁺ ion sputtering tests revealed that in the course of high-temperature N₂ treatment, the size of Pt⁰ particles on TiO₂ increases and a strong interaction between metal and support, i.e. Pt⁰ particles encapsulated by Ti_xO_y, happens, which are the reasons for the deactivation of Pt⁰/TiO₂ photocatalyst treated by high-temperature N₂.     

Study on the photocatalytic activity of TiN/TiO2 nanoparticle formed by ball milling

TiN/TiO₂ nanoparticle photocatalyst was prepared by ball milling of TiO₂ in H₂O solution doped with TiN. The photocatalyst was characterized by UV–Vis diffuse reflection spectroscopy, X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Based on the results of the characterization, the mechanism of the increase in photocatalytic activity was investigated. The results show that when the amount of doped TiN is 0.15 wt%, the photocatalytic activity of the TiN/TiO₂ is at its peak. Compared with TiO₂, the photoabsorption wavelength range of the TiN/TiO₂ photocatalyst red-shifts about 30 nm, and the photoabsorption intensity increases as well. The photocatalytic activities of the photocatalyst are higher than that of TiO₂ under UV and visible light irradiation. The increase of surface Ti³⁺ reactive center and the extension of the photoabsorption wavelength are the main factors for the increase in the photocatalytic activity of the TiN/TiO₂. Doped TiN neither changes the TiO₂ crystal phase nor creates new crystal phase by ball milling.     

Highly ordered anodic TiO2 nanotube arrays and their stabilities as photo(electro)catalysts

Highly ordered TiO₂ nanotube arrays with an average diameter of 230 nm, a wall thickness of 30 nm and a length of 1.8 μm were fabricated within a large domain by electrochemically anodizing of a titanium foil in a mixed solution of glycerol and NH₄F aqueous electrolyte. The TiO₂ nanotubes exhibit an anatase structure after annealing at 450 °C in air for 3 h. The direct photolysis (DP), photocatalytic (PC), electrocatalytic (EC) and photoelectrocatalytic (PEC) activities of the TiO₂ nanotube arrays were investigated using methyl orange (MO) as the model pollutant. The degradation of MO in PC process is faster than that in DP process, which confirms the photocatalysis of TiO₂ nanotube arrays. The degradation rate in PEC process is much higher than those in EC and PC processes, which demonstrates the synergetic effect between PC and EC processes. The synergetic factor is 4.1, which suggests that the synergetic effect is strong. Moreover, the stabilities of morphology, structure and photo(electro)catalytic degradation performance of the TiO₂ nanotube arrays were studied in order to evaluate their applicability as photo(electro)catalysts. The photo(electro)catalytic experiments bring neither morphological nor structural modifications to the nanotube arrays. The photo(electro)catalytic degradation rates of the TiO₂ nanotube arrays maintain stable in 10 cycles, which indicates that the TiO₂ nanotube arrays are appropriate to be applied as photo(electro)catalysts.     

From anodic TiO2 nanotubes to hexagonally ordered TiO2 nanocolumns

We report on the formation of hexagonally ordered TiO₂ nanocolumnar layers by electrochemical oxidation in a fluoride containing electrolyte, using self-organizing nanotube formation conditions at elevated potentials and low temperatures. The influence of the substrate temperature on the nanocolumn morphology and composition is investigated and characterized by FE-SEM and EDX. The origin of these nanocolumns can be attributed to a thickening of the inner tube wall of the double wall structure of self-organized TiO₂ nanotubes. Furthermore, a transition from nanocolumnar to nanotubular structure can be established by changing the applied voltage or applying a post-immersion treatment.     

Synthesis, characterization and effect of calcination temperature on phase transformation and photocatalytic activity of Cu,S-codoped TiO2 nanoparticles

A novel copper and sulfur codoped TiO₂ photocatalyst was synthesized by modified sol-gel method using titanium(IV) isopropoxide, CuCl₂·2H₂O and thiourea as precursors. The samples were characterized by X-ray diffraction (XRD), diffuse reflectance spectroscopy (DRS), scanning electron microscopy equipped with energy dispersive X-ray micro-analysis (SEM-EDX), transmission electron microscopy (TEM) and Fourier transform infrared (FT-IR) analysis. The XRD results showed undoped and Cu,S-codoped TiO₂ nanoparticles only include anatase phase. Effect of calcination temperature showed rutile phase appears in 650 and 700 °C for undoped and 0.1% Cu,S-codoped TiO₂, respectively. The SEM analysis revealed the doping of Cu and S does not leave any change in morphology of the catalyst surface. The increase of copper doping enhanced “red-shift” in the UV-vis absorption spectra. The TEM images confirmed the dopants suppressed the growth of TiO₂ grains. The photocatalytic activity of samples was tested for degradation of methyl orange (MO) solutions. The results showed photocatalytic activity of the catalysts with 0.05% Cu,0.05% S and 0.1% Cu,0.05% S were higher than that of other catalysts under ultraviolet (UV) and visible irradiation, respectively. Because of synergetic effect of S and Cu, the Cu,S-codoped TiO₂ catalyst has higher activity than undoped and Cu or S doped TiO₂ catalysts.     

Preparation, characterization of Au (or Pt)-loaded titania nanotubes and their photocatalytic activities for degradation of methyl orange

TiO₂ nanotubes were prepared by hydrothermal method and Au (or Pt) was loaded on TiO₂ nanotubes by photodeposition method. The photocatalysts were characterized by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy (DRS), X-ray photoelectron spectroscopy (XPS) and N₂ adsorption technique, respectively. The photocatalytic properties of the samples were also investigated. The results show that TiO₂ nanotubes with uniform diameter were prepared, and they have specific surface areas over 400 m²/g. The specific surface areas of TiO₂ nanotubes decrease with the increasing of calcining temperature, and crystalline phase of TiO₂ in the wall of nanotubes was transformed from anatase into rutile phase in calcination process. The photocatalytic activities of TiO₂ nanotubes are higher than that of nanosized TiO₂, and the photocatalytic activities of TiO₂ nanotubes were enhanced after loading Au (or Pt). After irradiation for 40 min under a 300 W of middle-pressure mercury lamp (MPML), the degradation rate of methyl orange solution using the Au/TiNT-500 (or Pt/TiNT-500) as a catalyst can reach 96.1% (or 95.1%). On the other hand, Au-loaded sample has evident adsorption peak in visible range, indicating that Au-loaded TiO₂ nanotubes are hopeful to become visible light photocatalyst.     

Enhanced photocatalytic degradation of Safranin-O by heterogeneous nanoparticles for environmental applications

Nanostructure titanium dioxide (TiO₂) has been synthesized by hydrolysis of titanium tetrachloride in aqueous solution and Ag-TiO₂ nanoparticles were synthesized by photoreduction method. The resulting materials were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier-transform infrared (FT-IR) and UV-vis absorption spectroscopy. The experimental results showed that the sizes of the synthesized TiO₂ and Ag-TiO₂ particles are in the range of 1.9-3.2 nm and 2-10 nm, respectively. Moreover, Ag-TiO₂ nanoparticles exhibit enhanced photocatalytic activity on photodegradation of Safranin-O (SO) dye as compared to pure TiO₂. The positive effect of silver on the photocatalytic activity of TiO₂ may be explained by its ability to trap electrons. This process reduces the recombination of light generated electron-hole pairs at TiO₂ surface and therefore enhances the photocatalytic activity of the synthesized TiO₂ nanoparticles. The effects of initial dye and nanoparticle concentrations on the photocatalytic activity have been studied and the results demonstrate that the dye photodegradation follows pseudo-first-order kinetics. The observed maximum degradation efficiency of SO is about 60% for TiO₂ and 96% for Ag-TiO₂.     

Preparation, characterization and photocatalytic activity of the neodymium-doped TiO2 nanotubes

A series of Nd-TiO₂ powders have been prepared by the sol-gel technique with neodymium nitrate and tetra-n-butyl titanium as raw materials, and then Nd-TiO₂ nanotubes were fabricated by the hydrothermal method with a 10 mol l⁻¹ NaOH solution. The as-prepared Nd-TiO₂ nanotubes were characterized by TEM, XRD, DRS, and XPS, and their photocatalytic activity was also tested in the case of the degradation of methyl orange in water. TEM photograph showed that Nd-TiO₂ nanotubes were about 10-20 nm in diameter, with the lengths range from 100 to 300 nm. TiO₂ nanotubes contained anatase and rutile crystallites. However, 0.3% Nd-TiO₂ nanotubes contained anatase crystallites, and only little rutile crystallites, so it is shown that neodymium doping hindered the phase transformation from anatase into rutile. Nd doping increased the visible-light absorption ability of Nd-TiO₂ nanotubes, and a red shift for Nd-TiO₂ nanotubes appeared when compared to TiO₂ nanotubes. XPS analysis showed that two types of oxygen existed on the photocatalyst surface, including metal-O and hydroxyl group, and more hydroxyl group was on the surface of 2% Nd-TiO₂ nanotubes than on the surface of TiO₂ nanotubes. Nd doping enhanced the photocatalytic activities of Nd-TiO₂ nanotubes, and 0.3% Nd-TiO₂ nanotubes exhibited the highest photocatalytic activity.     

Photocatalytic reduction of potassium chromate by Zn-doped TiO2/Ti film catalyst

The aim of this work was to investigate the photocatalytic (PC) reduction of potassium chromate by Zn-doped TiO₂/Ti film catalysts. The film catalyst was prepared by plasma electrolytic oxidation method in H₂SO₄ solution with different dosages of ZnSO₄. The composition and structure of the film catalysts was studied by XRD, SEM and EPMA. The removal rate of potassium chromate was investigated under the conditions of the different dosages of ZnSO₄ and the initial concentration of chromate potassium, and the reductive product during the PC reduction process was analyzed. The results showed that the film catalyst was composed of anatase TiO₂ and rutile TiO₂ with the porous structure. When the dosage of ZnSO₄ was 0.2 g/L, the film catalyst presented the highest catalytic activity, which related to the amount and the crystal grain size of anatase TiO₂ in the film. The PC reduction of potassium chromate by the film catalyst obeyed the pseudo-first-order kinetic equation. The UV-vis spectrum and XPS analyses proved that chromate Cr(VI) was reduced to Cr(III), which existed in the form of insoluble Cr(OH)₃.     

Applying the statistical experimental method to evaluate the process conditions of TiO2 nanotube arrays by anodization method

Vertically oriented TiO₂ nanotube arrays were successfully produced by the anodization technique in NH₄F/H₃PO₄ electrolyte. The structure and morphology were characterized by X-ray diffraction (XRD) and field emission scanning electron microscopy (FE-SEM). It is found that TiO₂ nanotube arrays annealed at 500 °C containing 100% anatase phase and entirely converted into rutile at 800 °C. The response surface methodology (RSM) and Box-Behnken design were applied to find the optimal factor conditions in production of TiO₂ nanotube arrays. Based on the results in preliminary experiments, we selected anodization time, anodization voltage and NH₄F concentration as the key factors to investigate their effects on responses. The regression models were built by fitting the experimental results with a second-order polynomial. By using the regression models, the optimal factor conditions were obtained as follows: anodization time of 300 min; anodization voltage of 15.39 V; NH₄F concentration of 0.50 M. Corresponding to the optimal factor conditions, the predicted average length and diameter of nanotube array were 1429 nm and 33 nm, respectively. Confirmation experiments using the optimized conditions were performed: TiO₂ nanotube arrays were obtained with an average tube length of 1420 nm and average tube diameter of 36 nm. The experimental results are in good agreement with the predicted results.     

Photoinduced deposition of gold nanoparticles on TiO<Subscript>2</Subscript>–WO<Subscript>3</Subscript> nanotube films as efficient photoanodes for solar water splitting

Gold-modified TiO₂–WO₃ nanotubes with different amounts of gold were obtained by two methods; photoassisted deposition and one-step electrochemical anodizing method. The morphology, crystallinity and elemental composition were studied by FE-SEM, XRD and EDX. The photoelectrochemical performance was examined under Xe light illumination in 1 M NaOH electrolyte. Characterization of the as-prepared TiO₂–WO₃ samples indicated that sodium tungstate concentration in anodizing solution significantly influenced the morphology and photoelectrochemical activity of fabricated films. Also, photoelectrochemical characterizations show that the photocatalytic activity of Au/TiO₂–WO₃ nanotubes was improved as compared with that of bare TiO₂–WO₃ nanotubes. The experimental results showed that the photocatalytic activities of Au/TiO₂–WO₃ were significantly affected by the amount of Au nanoparticles. The amount of gold nanoparticles was effectively controlled by time of photoreduction of the chloroauric acid solution. These new photoanodes showed enhanced high photocurrent density with good stability and are a highly promising photoanodes for photocatalytic hydrogen production.     

Photocatalytic activity of Eu-doped TiO2 ceramic films prepared by microplasma oxidation method

Mesoporous TiO₂ ceramic films have been fabricated on titanium plates by the microplasma oxidation method. To increase the photocatalytic activity of the films, Eu(NO₃)₃ of different concentrations are added to the H₂SO₄ electrolyte solution. X-ray diffraction, X-ray photoelectron spectroscopy, atomic force microscopy, scanning electron microscopy techniques, reused and regenerated experiments are applied to characterize the modified films. Rhodamine B is used to evaluate the photocatalytic activity of the modified films. The results show that Eu ions are found in the porous TiO₂ films, and the film has high photocatalytic activity, good adherence to substrate, better reuse and regeneration properties.     

Influence of anodization parameters on the morphology of TiO2 nanotube arrays

TiO₂ nanotube arrays can be fabricated by electrochemical anodization in organic and inorganic electrolytes. Morphology of these nanotube arrays changes when anodization parameters such as applied voltage, type of electrolyte, time and temperature are varied. Nanotube arrays fabricated by anodization of commercial titanium in electrolytes containing NH₄F solution and either sulfuric or phosphoric acid were studied at room temperature; time of anodization was kept constant. Applied voltage, fluoride ion concentration, and acid concentrations were varied and their influences on TiO₂ nanotubes were investigated. The current density of anodizing was recorded by computer controlled digital multimeter. The surface morphology (top-view) of nanotube arrays were observed by SEM. The nanotube arrays in this study have inner diameters in range of 40-80 nm.     

Synthesis and photocatalytic properties of porous TiO2 films prepared by ODA/sol-gel method

Porous TiO₂ films were deposited on SiO₂ pre-coated glass-slides by sol-gel method using octadecylamine (ODA) as template. The amount of ODA in the sol played an important role on the physicochemical properties and photocatalytic performance of the TiO₂ films. The films prepared at different conditions were all composed of anatase titanium dioxide crystals, and TiO₂ crystalline size got larger with increasing ODA amount. The maximum specific surface area of 41.5 m²/g was obtained for TiO₂ powders prepared from titanium sol containing 2.0 g ODA. Methyl orange degradation rate was enhanced along with increasing ODA amount and reached the maximal value at 2.0 g addition of ODA. After 40 min of UV-light irradiation, methyl orange degradation rate reached 30.5% on the porous film, which was about 10% higher than that on the smooth film. Porous TiO₂ film showed almost constant activity with slight decrease from 30.5% to 28.5% after 4 times of recycles.     

Synthesis and photocatalytic property of N-doped TiO2 nanorods and nanotubes with high nitrogen content

Nano N-doped TiO₂ nanotubes were fabricated by hydrothermally treating N-doped TiO₂ nanorods in a 8 M NaOH solution at 110 °C for 20 h. The N-doped TiO₂ nanorods were synthesized by a solvothermal process with precursor solution containing titanium sulfate, urea, and dichloroethane. The N-doped TiO₂ nanorods and nanotubes were characterized with X-ray diffraction, transmission electron microscopy, and UV-vis spectrophotometry. The nitrogen contents of the N-doped TiO₂ nanorods and nanotubes were reached to high values of 36.9 at.% and 25.7 at.%, respectively. The nitrogen doping narrowed the band gap of the N-doped TiO₂ nanorods and nanotubes and introduced indirect band gap to the powders, which respectively extended the absorption edge to visible light and infrared region. The nanotubes showed larger specific surface area and greater degradation efficiency to methyl orange than the nanorods.