Comparative study of titanium carbide and nitride coatings grown by cathodic vacuum arc technique

Titanium nitride (TiN), titanium carbide (TiC) thin films and TiC/TiN bilayers have been deposited on AISI 304 stainless steel substrates by plasma assisted physical vapor deposition technique—reactive pulsed vacuum arc method. The coatings were characterized in terms of crystalline structure, microstructure and chemical nature by X-ray diffraction and X-ray photoelectron spectroscopy, respectively. Tribological behavior was investigated using ball on disc technique. The average coefficient of friction was measured, showing lower values for the TiN/TiC bilayer. Dynamic wear curves were performed for each coating, observing a better wear resistance for TiN/TiC bilayers, compared to TiN and TiC monolayers. On the other hand, the TiCN formation in the TiN/TiC bilayer was observed, being attributed to the interdiffusion between TiN and TiC at the interface. Moreover, the substrate temperature influence was analysing observing a good behavior at T_S = 115 °C.     

TiAlN coatings deposited by triode magnetron sputtering varying the bias voltage

TiAlN films were deposited on AISI O1 tool steel using a triode magnetron sputtering system. The bias voltage effect on the composition, thickness, crystallography, microstructure, hardness and adhesion strength was investigated. The coatings thickness and elemental composition analyses were carried out using scanning electron microscopy (SEM) together with energy dispersive X-ray (EDS). The re-sputtering effect due to the high-energy ions bombardment on the film surface influenced the coatings thickness. The films crystallography was investigated using X-ray diffraction characterization. The X-ray diffraction (XRD) data show that TiAlN coatings were crystallized in the cubic NaCl B1 structure, with orientations in the {1 1 1}, {2 0 0} {2 2 0} and {3 1 1} crystallographic planes. The surface morphology (roughness and grain size) of TiAlN coatings was investigated by atomic force microscopy (AFM). By increasing the substrate bias voltage from −40 to −150 V, hardness decreased from 32 GPa to 19 GPa. Scratch tester was used for measuring the critical loads and for measuring the adhesion.     

Bilayer period effect on corrosion-erosion resistance for [TiN/AlTiN]n multilayered growth on AISI 1045 steel

The aim of this work is to study the electrochemical behavior, under a corrosion-erosion condition, of [TiN/AlTiN]_n multilayer coatings with bilayers periods of 1, 6, 12 and 24, deposited by a magnetron sputtering technique on Si (1 0 0) and AISI 1045 steel substrates.The TiN and AlTiN structure for multilayer coatings were evaluated via X-ray diffraction (XRD) analysis. Silica particles were used as an abrasive in the corrosion-erosion test within a 0.5 M H₂SO₄ solution at an impact angle of 30° over the surface. The electrochemical characterization was carried out using a polarization resistance technique (Tafel), in order to observe changes in the corrosion rate as a function of the bilayers number (n) or bilayer period (Λ). Corrosion rate values of 359 mpy in uncoated steel substrate and 1.016×10⁻⁶ mpy for substrate coated with [TiN/AlTiN]₂₄ under impact angle of 30° were found. This behavior was related with the mass loss curve for all coatings and the surface damage was analyzed using SEM images. These results indicate that TiN/AlTiN multilayer coatings deposited on AISI 1045 steel provide a practical solution for applications in erosive-corrosive environments.     

Characterization of Ti-Zr-N films deposited by cathodic vacuum arc with different substrate bias

Ti-Zr-N (multi-phase) films were prepared by cathodic vacuum arc technique with different substrate bias (0 to −500 V), using Ti and Zr plasma flows in residual N₂ atmosphere. It was found that the microstructure and mechanical properties of the composite films are strongly dependent on the deposition parameters. All the films studied in this paper are composed of ZrN, TiN, and TiZrN ternary phases. The grains change from equiaxial to columnar and exhibit preferred orientation as a function of substrate bias. With the increase of substrate bias the atomic ratio of Ti to Zr elements keeps almost constant, while the N to (Ti + Zr) ratio increases to about 1.1. The composite films present an enhanced nanohardness compared with the binary TiN and ZrN films deposited under the same condition. The film deposited with bias of −300 V possesses the maximum scratch critical load (L_c).     

A study of TiMoN nano-multilayer coatings deposited by CFUBMSIP using DC and HIPIMS power

TiMoN nano-multilayer hard coatings have been deposited using the closed field unbalanced magnetron sputter ion plating (CFUBMSIP) technique. In one set of experiments, standard DC power supplies were used on four magnetrons in the CFUBMSIP system (4DC magnetrons). The second set of experiments was also in the same magnetic field configuration of CFUBMSIP, but three magnetrons were as again powered with standard DC whilst one magnetron with Ti target was supplied by a high power impulse magnetron sputtering (HIPIMS) power generator (3DC + 1HIPIMS magnetrons). Two elemental titanium sputtering targets and two of molybdenum were used to produce the TiMoN nano-multilayer coatings. Analysis of the coatings was carried out to investigate the differences in terms of properties, compositions and microstructures of the coatings deposited by these two sets of experiments. It was found that the coatings deposited by both sets of the experiments exhibited similar properties of high hardness, good adhesion and exceptional wear resistance, with a lower sliding friction than more commonly used hard coatings including TiN, CrN, TiAlN, CrTiAlN etc. Although the initial TiN coating as formed at the coating-substrate interface using the process of 3DC + 1HIPIMS magnetrons appeared to show a less oriented microstructure in comparison with that of the coating produced by the process using 4DC magnetrons, the compositions and cross sectional microstructures of the bulk of the coatings did not show significant differences, as observed by the cross sectional Transmission Electron Microscopy microstructures of these two types of TiMoN coatings.     

Ti-Cu-N hard nanocomposite films prepared by pulse biased arc ion plating

In this work, Ti-Cu-N hard nanocomposite films were deposited on high-speed-steel (HSS) substrates using a TiCu (88:12 at.%) single multi-component target by pulse biased arc ion plating. The influence of pulse bias voltages was examined with regard to elemental composition, structure, morphology and mechanical properties of the films. The Cu atomic content of Ti-Cu-N films was determined by Electron Probe Micro-Analyzer (EPMA). The structure and morphology were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Hardness and film/substrate adhesion were determined by nanoindenter and scratch test, respectively. The results showed that the content of Cu appeared to be in the range of 1.75-4.5 at.%, depending on pulse bias voltages. The films exhibit a preferred orientation TiN (1 1 1) texture when the substrate bias voltages were −100 V and −300 V, while the preferred orientation change to be a preferred orientation TiN (2 2 0) one when the substrate bias voltages increase to −600 V and −900 V. And no obvious sign of metal copper phase was observed. The SEM morphologies showed some macroparticles (MPs) on the surface of the films and the relative content of the MPs decreased significantly when the substrate bias voltages increased from −100 to −900 V. The maximum value (74 N) of the film/substrate adhesion of the films was obtained when the substrate bias voltage was −600 V with Cu content of 1.75 at.%. Hardness enhancement was observed, the value of the hardness increased firstly and reached a maximum value of 31.5 GPa, corresponding to Cu content of 1.75 at.%, and then it decreased when the substrate bias voltage changed from −100 to −900 V. The hardness enhancement was discussed related to the concept for the design of hard materials.     

Ti/TiN multilayer thin films deposited by pulse biased arc ion plating

In this work, the effect of modulation period (Λ) on Ti/TiN multilayer films deposited on high-speed-steel (HSS) substrates using pulse biased arc ion plating is reported. The crystallography structures and cross-sectional morphology of Ti/TiN multilayer films were characterized by X-ray diffraction analysis (XRD) and scanning electron microscopy (SEM), respectively. Their mechanical properties were determined via nanoindentation measurements, while the film/substrate adhesion via the scratch test. It was found that the highest hardness value reached 43 GPa for the modulation period of 54 nm, while the film/substrate adhesion also reached the highest value of 83 N. Furthermore, the hardness enhancement mechanism in the multilayer films is discussed.     

Study of TiN and ZrN thin films grown by cathodic arc technique

Thin films of TiN and ZrN were grown on stainless steel 316 substrate using the pulsed cathodic arc technique with different number of discharges (one to five discharges). The coatings were characterized in terms of crystalline structure, microstructure, elementary chemical composition and stoichiometric by X-ray diffraction (XRD), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy for chemical analyses (XPS), respectively. The XRD results show that for TiN as for ZrN, the preferential direction occurs in the plane (2 0 0), and this result stays when increasing the number of discharges. The grain size is increased with the increase of the number of discharges for both nitrides, the roughness for the TiN film is greater than for the ZrN film; these results were determined by AFM. XPS analysis determined that there is a higher nitrogen presence in the ZrN film than in the TiN film.     

Characterization of bilayer coatings of TiN/ZrN grown using pulsed arc PAPVD

Nitride coatings have been used to increase hardness and to improve the wear and corrosion resistance of structural materials. Coatings of TiN/ZrN were grown on stainless steel substrates using a physical vapour deposition system assisted by pulsed arc plasma (PAPVD). The coatings have been characterized by X-ray diffraction (XRD) in order to identify the present phases of the films, microstrain level generated, crystallite size and the variation of the lattice parameter. The results showed plane orientations (1 1 1) and (2 0 0) in both TiN and ZrN films. Morphology surface analysis of the samples were performed using a scanning probe microscope to characterize the grain size and roughness in the mode of the atomic force microscopy (AFM) hence it was observed that the root-mean-squared (rms) roughness for ZrN is smaller than for TiN. Besides elastic and friction properties of the films were characterized qualitatively, and then, they were compared with those of the substrates by using force modulation microscopy (FMM) and lateral force microscopy (LFM) modes. In addition, an elemental analysis of the samples was realized by means of energy dispersive spectroscopy (EDS). Both, XRD and AFM results are given as a function of the number of shots. Chemical states of the TiN and ZrN films were determined by X-ray photoelectron spectroscopy (XPS).     

Nanolayered multilayer coatings of CrN/CrAlN prepared by reactive DC magnetron sputtering

Single-phase CrN and CrAlN coatings were deposited on silicon and mild steel substrates using a reactive DC magnetron sputtering system. The structural characterization of the coatings was done using X-ray diffraction (XRD). The XRD data showed that both the CrN and CrAlN coatings exhibited B1 NaCl structure with a prominent reflection along (2 0 0) plane. The bonding structure of the coatings was characterized by X-ray photoelectron spectroscopy and the surface morphology of the coatings was studied using atomic force microscopy. Subsequently, nanolayered CrN/CrAlN multilayer coatings with a total thickness of approximately 1 μm were deposited on silicon substrates at different modulation wavelengths (Λ). The XRD data showed that all the multilayer coatings were textured along {2 0 0}. The CrN/CrAlN multilayer coatings exhibited a maximum nanoindentation hardness of 3125 kg/mm² at a modulation wavelength of 72 Å, whereas single layer CrN and CrAlN deposited under similar conditions exhibited hardness values of 2375 and 2800 kg/mm², respectively. Structural changes as a result of heating of the multilayer coatings in air (400-800 °C) were characterized using XRD and micro-Raman spectroscopy. The XRD data showed that the multilayer coatings were stable up to a temperature of 650 °C and peaks pertaining to Cr₂O₃ started appearing at 700 °C. These results were confirmed by micro-Raman spectroscopy. Nanoindentation measurements performed on the heat-treated coatings revealed that the multilayer coatings retained hardness as high as 2250 kg/mm² after annealing up to a temperature of 600 °C.     

Effect of pulsed bias on properties of ZrN/TiZrN films deposited by cathodic vacuum arc

ZrN/TiZrN multilayer are deposited by cathodic vacuum arc method with different substrate bias (from 0 to -800 V), using Ti and Zr plasma flows in residual N₂ atmosphere, combined with ion bombardment of sample surfaces. The effect of pulsed bias on structure and properties of films is investigated. Microstructure of the coating is analyzed by X-ray diffraction (XRD), and scanning electron microscopy (SEM). Meanwhile, the nanohardness, Young's modulus, and scratch tests are performed. The experimental results show that the films exhibit a nanoscale multilayer structure consisting of TiZrN and ZrN phases. Solid solutions are formed for component TiZrN films. The dominant preferred orientation of TiZrN films is (111) and (220). At pulsed bias of -200 V, the nanohardness and the adhesion strength of ZrN/TiZrN multilayer reach a maximum of 38 GPa, and 78 N, respectively. The ZrN/TiZrN multilayer demonstrates an enhanced nanohardness compared with binary TiN and ZrN films deposited under equivalent conditions.     

Effect of spraying power on microstructure and bonding strength of MoSi2-based coatings prepared by supersonic plasma spraying

MoSi₂-based oxidation protective coatings for SiC-coated carbon/carbon composites were prepared using a supersonic plasma spraying at the power of 40 kW, 45 kW, 50 kW and 55 kW, respectively. Effect of spraying power on the microstructure and bonding strength of MoSi₂-based coatings was studied. The results show that coatings become more and more compact and the bonding strength increases when the spraying power increases from 40 kW to 50 kW. At the power of 50 kW, the coatings were dense and the bonding strength reached a maximum value of 14.5 MPa. As the spraying power is of sufficient magnitude, many cracks and pores reappaer in coatings and the bonding strength between coating and substrate also decreases.     

Improvement of mechanical and tribological properties in steel surfaces by using titanium-aluminum/titanium-aluminum nitride multilayered system

Improvement of mechanical and tribological properties on AISI D3 steel surfaces coated with [Ti-Al/Ti-Al-N]_n multilayer systems deposited in various bilayer periods (Λ) via magnetron co-sputtering pulsed d.c. method, from a metallic binary target; has been studied in this work exhaustively. The multilayer coatings were characterized in terms of structural, chemical, morphological, mechanical and tribological properties by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), scanning electron microscopy, nanoindentation, pin-on-disc and scratch tests, respectively. The failure mode mechanisms were studied by optical microscopy. Results from X-ray diffraction analysis revealed that the crystal structure of TiAl/TiAlN multilayer coatings has a tetragonal and FCC NaCl-type lattice structures for Ti-Al and Ti-Al-N, respectively, i.e., it was found to be non-isostructural multilayers. An enhancement of both hardness and elastic modulus up to 29 GPa and 260 GPa, respectively, was observed as the bilayer periods (Λ) in the coatings were decreased. The sample with a bilayer period (Λ) of 25 nm and bilayer number n = 100 showed the lowest friction coefficient (∼0.28) and the highest critical load (45 N), corresponding to 2.7 and 1.5 times better than those values for the coating deposited with n = 1, respectively. These results indicate an enhancement of mechanical, tribological and adhesion properties, comparing to the [Ti-Al/Ti-Al-N]_n multilayer systems with 1 bilayer at 26%, 63% and 33%, respectively. This enhancement in hardness and toughness for multilayer coatings could be attributed to the different mechanisms for layer formation with nanometric thickness such as the novel Ti-Al/Ti-Al-N effect and the number of interfaces that act as obstacles for the crack deflection and dissipation of crack energy.     

Microstructures and tribological properties of CrN/ZrN nanoscale multilayer coatings

Nanoscale multilayer CrN/ZrN coatings with bilayer thicknesses ranging from 11.7 to 66.7 nm were prepared by reactive magnetron sputtering techniques. The structure of the thin films was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). X-ray diffraction results showed that CrN individual layers presented a <1 1 1> preferred orientation in the multilayer coatings. The diffraction peaks of CrN shifted continuously to low diffraction angle with decreasing bilayer thickness. TEM observations showed that the multilayer did not form a superlattice structure instead of the coexistence of nanocrystalline CrN and ZrN layers. Columnar growth for all the coatings was observed by cross-sectional SEM. Nanoindentation tests showed that the multilayer coatings had almost a constant nanohardness of 29 GPa in spite of the variations of bilayer thickness. Pin-on-disk tests indicated that both the friction coefficients and wear rates increased when decreasing bilayer thickness. However, in comparison with the monolayer coating, the multilayer coatings exhibited excellent wear resistance.     

The effects of Si3N4 interlayer on the thermal stability and hardness of Ti/TiNx (x = 0.5-1) nanolayered coatings

The polycrystalline Ti/TiN_x multilayer films were deposited by magnetron sputtering, and the as-deposited multilayer coatings were annealed at 500-800 °C for 2-4 h in vacuum. We investigated the effects of annealing temperature and annealing time on the microstructural, interfacial, and mechanical properties of the polycrystalline Ti/TiN_x multilayer films. It was found that the hardness increased with annealing temperature. This hardness enhancement was probably caused by the preferred crystalline orientation TiN(1 1 1). The X-ray reflectivity measurements showed that the layer structure of the coatings could be maintained after annealing at 500 °C and the addition of the Si₃N₄ interlayer to Ti/TiN_x multilayer could improve the thermal stability to 800 °C.     

Deposition of TiSiN coatings by arc ion plating process

Titanium silicon nitride (TiSiN) thin films were deposited on tungsten cemented carbide tools by cathode arc ion plating (AIP) process using alloy TiSi targets. The effects of silicon addition and negative substrate bias on the development of the textures of films were studied systematically by varying the bias voltage from −20 to −200 V. The structural features of the films were investigated in detail using X-ray diffraction. The effect of the texture on such mechanical properties as hardness and adhesion of the films was also studied. A maximum hardness of 42 GPa was obtained at a DC substrate bias of −150 V. The characteristics of TiSiN thin films exhibited excellent adhesion of over 150 N. The cutting performance of end-mills and drillers was evaluated by milling and drilling of highly hardened material under high-speed cutting conditions. The results reveal that cutting tools with TiSiN coatings markedly outperformed those with TiN coatings, and the uncoated cutting tools. TiSiN coating increased the cutting lifetime to seven times that of the uncoated one.     

The effect of applied negative bias voltage on the structure of Ti-doped a-C:H films deposited by FCVA

Ti-doped hydrogenated diamond-like carbon (DLC) films were deposited on Si(1 0 0) substrates by a filtered cathodic vacuum arc (FCVA) method using Ar and CH₄ as the feedstock. The composition and microstructure of the films were investigated by Raman spectroscopy, X-ray photoelectron spectroscopy and IR spectroscopy. The internal stress was determined by the radius of curvature technique. The influence of the bias voltage on the microstructure of the as-deposited films was investigated. It was found that the graphite-like bonds was dominated in the Ti-doped DLC film deposited at 0 V bias voltage. When bias voltage was increased to −150 V, more diamond-like bond were produced and the sp³ content in film reached the maximum value, after which it decreased and more graphite-like bonds feature produced with further increase of the negative bias voltage. The compressive internal in the Ti-doped DLC films also exhibited a maximum value at −150 V bias voltage. IR results indicated that CH bonded intensity reduced, and H atoms bonded with C atoms were substituted for the Ti atoms as the negative bias voltage increasing. All the composition and microstructure change can be explained by considering the plasma conditions and the effect of negative bias voltage applied to the substrate.     

Microstructure and friction and wear behavior of laser boronizing composite coatings on titanium substrate

Three kinds of laser boronizing composite coatings were in situ synthesized on Ti substrate by using powders of B, BN and B₄C as starting materials. Microstructures of the laser boronizing composite coatings were investigated by means of X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM); and their worn surface morphologies were also observed by using SEM. Moreover, the friction and wear behavior of the boronizing composite coatings under dry sliding condition were evaluated using a UMT-2MT friction and wear tester. It was found that all the three types of laser boronizing composite coatings had higher microhardness and better wear resistance than pure Ti substrate; and their microstructure and wear resistance varied with varying pre-placed powders of B, BN, and B₄C. Under the same dry sliding test conditions, the wear resistance of the three kinds of laser boronizing composite coatings, i.e., sample 1 prepared from pre-placed B, sample 2 obtained from pre-placed BN, and sample 3 fabricated from pre-placed B₄C, is ranked in an order of sample 1 > sample 2 > sample 3, which, surprisingly, well conforms to their order of hardness and friction coefficients.     

Structural and mechanical properties of compositionally gradient CrNx coatings prepared by arc ion plating

Compositionally gradient CrN_x coatings were fabricated using arc ion plating by gradually increasing N₂ flow rate during the deposition process. The effect of substrate bias, ranging from 0 to −250 V, on film microstructure and mechanical properties were systematically investigated with XRD, SEM, HRTEM, nanoindentation, adhesion and wear tests. The results show that substrate bias has an important influence on film microstructure and mechanical properties of gradient CrN_x coatings. The coatings mainly crystallized in the mixture of hexagonal Cr₂N, bcc Cr and fcc rock-salt CrN phases. N₂ flow rate change during deposition results in phase changes in order of Cr, Cr + Cr₂N, Cr₂N, Cr₂N + CrN, and CrN, respectively, along thickness direction. Phase fraction and preferred orientation in CrN_x coatings vary with substrate bias, exerting an effective influence on film hardness. With the increasing of bias, film microstructure evolves from an apparent columnar structure to a highly dense one. The maximum hardness of 39.1 GPa was obtained for the coatings deposited at a bias of −50 V with a friction coefficient of 0.55. It was also found that adhesion property and wear resistance of gradient CrN_x coatings were better than that of homogeneous CrN coatings.     

Characteristics of ZrC/ZrN and ZrC/TiN multilayers grown by pulsed laser deposition

ZrC/ZrN and ZrC/TiN multilayers were grown on (1 0 0) Si substrates at 300 °C by the pulsed laser deposition (PLD) technique using a KrF excimer laser. X-ray diffraction investigations showed that films were crystalline, the strain and grain size depending on the nature and pressure of the gas used during deposition. The elemental composition, analyzed by Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS), showed that films contained a low level of oxygen contamination. Simulations of the X-ray reflectivity (XRR) curves acquired from films indicated a smooth surface morphology, with roughness below 1 nm (rms) and densities very close to bulk values.Nanoindentation results showed that the ZrC/ZrN and ZrC/TiN multilayer samples exhibited hardness values between 30 and 33 GPa, slightly higher than the values of 28-30 GPa measured for pure ZrC, TiN and ZrN films.