A surface-reactive rod-coil diblock copolymer: nano- and micropatterned polymer brushes.

A diblock copolymer consisting of poly(3-(triethoxysilyl)propylisocyanate) (PIC) and polystyrene(PS) was synthesized by anionic polymerization. A polymeric monolayer of the block copolymer was formed on silica substrates by various grafting techniques such as immersion, casting, or contact-printing. The PIC block adheres covalently to Si substrates in an in-plane fashion due to its extended rodlike conformation and reactivity to the silica. The polystyrene blocks aggregate to form mounds on the surface resulting in a new type of nanopatterned polymer brush. The self-limiting adsorption of the rod coils results in a thickness of about 5 nm regardless of the solution concentration and coating method. This particular property allowed microcontact printing directly onto silicon or glass substrates. The resulting surface morphology consisted of nanoscale domains given by the block copolymer and uniform thickness micropatterns transferred from the stamp within the printed area. This study offers a simple new method to prepare a covalent polymeric monolayer with nano- and micropatterns, which can be performed directly onto various silicon-based substrates.     

Solvent-induced self-assembly of mixed poly(methyl methacrylate)/polystyrene brushes on planar silica substrates: molecular weight effect

The effect of molecular weight on the solvent-induced self-assembly of mixed poly(methyl methacrylate) (PMMA)/polystyrene (PS) brushes on silicon wafers was studied. For a series of mixed brushes with a fixed PMMA M(n) and systematically changed PS M(n), a transition in water advancing contact angle (theta(a)) from 74 degrees, the value for a flat PMMA surface, to 91 degrees, the value for a flat PS film, was observed with increasing PS M(n) after treatment with CHCl(3). Atomic force microscopy studies showed smooth surfaces for all samples. While no significant changes in surface morphologies were observed after treatment with cyclohexane, a selective solvent for PS, contact angle and XPS studies indicated that the mixed brushes with a PS M(n) slightly smaller than that of PMMA underwent self-reorganization, exhibiting a different theta(a). Intriguing surface morphologies composed of relatively ordered nanoscale domains were found from mixed brushes with PS M(n) slightly smaller than or similar to that of PMMA after treatment with acetic acid, a selective solvent for PMMA. The nanodomains are speculated to be of a micellar structure, with PS chains forming a core shielded by PMMA chains.     

Surface aggregation structure and surface mechanical properties of binary polymer blend thin films

During preparation of very thin polymer belnd films from a solution of polymers, the phase‐separated structures which are quite different from that observed for the bulk blend film was observed. From atomic force microscopic(AFM) observation, it is concluded that the surface undulation, which reflects the phase separated morphology of the blend system, is present. In the case of (polystyrene(PS)/poly(methyl methacrylate)(PMMA)) blend system, a large influence of end‐group chemistry on the surface morphology was observed. The phase identification of the (rubbery polymer/glassy polymer) binary blend thin films was successfully achieved by scanning vioscoelasticity microsopy(SVM).     

Protein adhesion on silicon-supported hyperbranched poly(ethylene glycol) and poly(allylamine) thin films

Hyperbranching poly(allylamine) (PAAm) and poly(ethylene glycol) (PEG) on silicon and its effect on protein adhesion was investigated. Hyperbranching involves sequential grafting of polymers on a surface with one of the components having multiple reactive sites. In this research, PAAm provided multiple amines for grafting PEG diacrylate. Current methodologies for generating PEG surfaces include PEG-silane monolayers or polymerized PEG networks. Hyperbranching combines the nanoscale thickness of monolayers with the surface coverage afforded by polymerization. A multistep approach was used to generate the silicon-supported hyperbranched polymers. The silicon wafer surface was initially modified with a vinyl silane followed by oxidation of the terminal vinyl group to present an acid function. Carbodiimide activation of the surface carboxyl group allowed for coupling to PAAm amines to form the first polymer layer. The polymers were hyperbranched by grafting alternating PEG and PAAm layers to the surface using Michael addition chemistry. The alternating polymers were grafted up to six total layers. The substrates remained hydrophilic after each modification. Static contact angles for PAAm (32-44 degrees) and PEG (33-37 degrees) were characteristic of the corresponding individual polymer (30-50 degrees for allylamine, 34-42 degrees for PEG). Roughness values varied from approximately 1 to 8 nm, but had no apparent affect on protein adhesion. Modifications terminating with a PEG layer reduced bovine serum albumin adhesion to the surface by approximately 80% as determined by ELISA and radiolabel binding studies. The hyperbranched PAAm and PEG surfaces described in this paper are nanometer-scale, multilayer films capable of reducing protein adhesion.     

从溶胀平衡研究玻璃态高聚物的凝聚缠结网络

在13~15℃室温条件下对聚苯乙烯(PS)颗粒在二氧六环/水混合溶剂中的溶胀情况进行目视观察,可以看到,当减小混合溶剂二氧六环/水中的水含量时,PS颗粒从玻璃态到溶胀的玻璃态、溶胀的高弹态、流体态的转变,与PS颗粒升温时从玻璃态到高弹态、流体态的转变相对应.选定混合溶剂二氧六环/水(水6·8wt%)对一个单分散PS试样(Mw=1·68×105)在30℃进行分相平衡和溶胀平衡的测定.分相平衡是先将PS/二氧六环/水(混合溶剂水含量6·8wt%)体系加热到130℃使PS溶解成一均相溶液,然后在冷却过程中分相,在30℃达分相平衡(30天)时,浓相高分子体积浓度p″=0·304,稀相几乎为纯溶剂.从Flory-Huggins相平衡理论得出此体系的高分子-溶剂相互作用参数χ=0·63.本工作使用的单分散PS试样在选定的混合溶剂,即二氧六环/水(水6·8wt%)中,30℃时不能溶解只能溶胀,单分散PS颗粒淬冷试样(密度ρp=1·0451g/mL)到达溶胀平衡(80天)时浓相高分子体积浓度p″=0·308.而此淬冷试样经在80℃热处理100h后的老化试样(ρp=1·0470g/mL)达溶胀平衡(70天)时p″=0·312.从溶胀过程中浓相体积变化曲线可知试样经在80℃热处理过程中凝聚网络趋向于更均一,更接近热处理温度下的平衡态,试样密度增大,网络产生了新的链间凝聚,物理交联密度增大(凝聚点间分子量减小).从溶胀平衡理论并取χ=0·63(分相平衡)可得到淬冷试样的物理交联点间分子量Mc=11·6×104,老化试样的物理交联点间分子量Mc=6·9×104.实验结果说明溶胀过程及溶胀平衡的测定可以反映玻璃态高聚物中的凝聚网络结构的细节,而且非常敏感.     

Polymerizability,copolymerizability, and properties of cyanoacrylate‐telechelic polyisobutylenes II: copolymerization of three‐arm star cyanoacrylate‐ telechelic polyisobutylene with ethyl cyanoacrylate

This research concerned the synthesis and characterization of novel conetworks containing polyisobutylene (PIB) and polyethyl‐2‐cyanoacrylate [poly(Et‐CA)] sequences. The syntheses involved the copolymerization of CA‐telechelic three‐arm star PIB [Ø(PIB‐CA)₃] with ethyl‐2‐cyanoacrylate (Et‐CA) mediated by nucleophiles or by living tissue (fresh eggs). The conetworks were characterized by swelling in hexanes, tetrahydrofuran (THF), and acetone, and the results indicate co‐continuous PIB and poly(Et‐CA) domains. The conetworks exhibit two T_gs indicating phase‐separation between PIB and poly(Et‐CA). The outstanding oxidative resistance of the conetworks was demonstrated by exposure to concentrated nitric acid. The tensile strengths, moduli, and elongations of a series of conetworks with different overall compositions were investigated and the findings interpreted in terms of covalently linked rubbery and glassy domains. AFM also suggests the presence of phase‐separated rubbery and glassy domains. DMTA spectra of a Ø(PIB‐CA)₃ homonetwork, and Ø(PIB‐CA)₃/Et‐CA conetworks were analyzed and interpreted in terms of coexisting rubbery and glassy domains. Observations made during the exposure of Ø(PIB‐CA)₃/Et‐CA mixtures to proteinaceous tissue, in combination with characterization data, were used to propose a structural model for the conetworks. Copyright © 2007 John Wiley & Sons, Ltd.     

Effect of molecular weight on synthesis and surface morphology of high-density poly(ethylene glycol) grafted layers

This work describes studying the permanent grafting of carboxylic acid end-functionalized poly(ethylene glycol) methyl ether (PEG) chains of different molecular weights from the melt onto a surface employing poly(glycidyl methacrylate) ultrathin film as an anchoring layer. The grafting led to the synthesis of the complete PEG brushes possessing exceptionally high grafting density. The maximum thickness of the attached PEG films was strongly dependent on the length of the polymer chains being grafted. The maximum grafting efficiency was close to the critical entanglement molecular weight region for PEG. All grafted PEG layers were in the "brush regime", since the distance between grafting sites for the layers was lower than the end-to-end distance for the anchored macromolecules. Scanning probe microscopy revealed that the grafting process led to complete PEG layers with surface smoothness on a nanometric scale. Practically all samples were partly or fully covered with crystalline domains that disappeared when samples were scanned under water. Due to the PEG hydrophilic nature, the surface with the grafted layer exhibited a low (up to 21 degrees ) water contact angle.     

End‐grafting copolymers of styrene and 4‐vinylpyridine on an interacting solid surface

Copolymers of styrene and 4‐vinylpyridine with a styrene fraction f varying from 1 to 0 were grafted onto a silicon substrate in the melt. The grafting reaction and the stability of the grafted chains were investigated by Fourier transform infrared and X‐ray photoelectron spectroscopy. The thickness and surface morphology of the grafted copolymer layers were characterized with ellipsometry and atomic force microscopy (AFM). The copolymer chains were successfully grafted to the surface of the silicon substrate by a reaction between the hydroxyl groups of the nitroxide moiety at the end of the copolymers and the silanol groups on the surface of the silicon wafer. A measurement of the thickness of the grafted copolymer layers showed that the ratio of grafted‐layer thickness to the unperturbed chain radius of gyration decreased with the increasing fraction of 4‐vinylpyridine in the copolymer; this indicated that the grafted layer was strongly attracted to the substrate. In addition, an accelerated grafting process was observed at grafting times ranging from 48 to 72 h for pure poly(4‐vinylpyridine) and copolymers with f values of 0.3 and 0.5. AFM observation revealed that the grafted layers densely and homogeneously covered the silicon substrate. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1332‐1343, 2005     

A facile method of forming nanoscale patterns on poly(ethylene glycol)-based surfaces by self-assembly of randomly grafted block copolymer brushes

Poly(oligo(ethylene glycol) methacrylate) (POEGMA) block poly(methyl methacrylate) (PMMA) brushes were synthesized on the silicon wafer surfaces by the surface-initiated atom transfer radical polymerization (ATRP) method. Atomic force microscopy, ellipsometry, and water contact angle methods were employed to study the surface morphology and stimulus-response behavior. It was found that simple solvent treatments could induce phase segregation of the POEGMA and PMMA segments thus introducing nanoscale patterns. The feature size could be less than 10 nm and was tunable on the nanoscale. Various patterns including spherical aggregates, wormlike aggregates, stripe patterns, perforated layers, and complete overlayers were obtained through adjusting the upper block layer thickness. These patterns could switch between the different morphologies reversibly after the treatment with selective solvents.     

PS/PMMA mixed polymer brushes on the surface of clay layers: Preparation and application in polymer blends

Polystyrene (PS) and poly(methyl methacrylate) (PMMA) mixed polymer brushes on the surface of clay layers were prepared by using in situ free radical polymerization. Free radical initiator molecules with two quaternary ammonium groups at both ends were intercalated into the interlayer spacing of clay layers. The amount of polymer brushes grafted on the surface of clay layers can be controlled by controlling the polymerization time. Thermogravimetric analysis, X‐ray diffraction, and high‐resolution transmission electron microscope results indicated successful preparation of the mixed polymer brushes on the surface of clay layers. The kinetics of the grafting of the monomers was also studied. The mixed polymer brushes on the surface of clay layers were used as compatibilizers in blends of PS and PMMA. In the blends, the intercalated clay particles tend to locate at the interface of two phases reducing the interfacial tension. In the meanwhile, PMMA homopolymer chains tend to intercalate into clay layers. The driving force for the intercalation is the compatibility between homo‐PMMA chains and PMMA brushes on the surface of clay layers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5329–5338, 2007     

Confined crystallization in lamellae forming poly(3-(2′-ethyl)hexylthiophene) (P3EHT) block copolymers

Charge transport in poly(3-alkylthiophene)s (P3AT)s is closely linked to the nanoscale organization of crystallites. Block copolymer morphologies provide an ideal platform to study crystallization as the chain ends are tethered at a known interface in a well-defined geometry. The impact of soft versus hard confinement on P3EHT crystallization was studied using poly(3-(2′-ethyl)hexylthiophene) (P3EHT) containing diblocks with both rubbery poly(methyl acrylate) (PMA) and glassy polystyrene (PS) blocks. Here, P3EHT's lower melting point relative to the commonly studied poly(3-hexylthiophene) (P3HT) facilitated its confined crystallization and makes it an ideal model system. While transmission electron microscopy (TEM) and small angle X-ray scattering (SAXS) revealed well-ordered lamellar morphologies both in the melt and post-crystallization for both sets of diblocks, the glassy blocks inhibit confined crystallization of P3EHT relative to rubbery matrix blocks. Analysis of aligned diblocks by both SAXS and wide angle X-ray scattering (WAXS) revealed that the P3EHT chain axis aligns perpendicular to domain interfaces, allowing preferential growth of the alkyl-chain and π–π stacking directions parallel to lamellae. Finally, it was shown that following diblock self-assembly in the melt, crystallite growth drives expansion of microdomains to match the P3EHT contour length. It was concluded that P3EHT chains adopted an extended conformation within confined crystallites due to the rigid nature of polythiophenes relative to flexible chain crystalline polymers. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 205–215     

Morphology and grafting in polybutylacrylate-polystyrene core-shell emulsion polymerization

The morphology of polybutylacrylate–polystyrene (PBA–PS) core-shell latex particles prepared by seeded emulsion polymerization was investigated as a function of the addition method of styrene (St). The thin layer chromatography/flame ionization detector (TLC–FID) technique was used to characterize the morphology of the core-shell latexes. It was found that grafting PS to the PBA core occurs during seeded emulsion polymerization. The percentage of grafting depended on the method of addition of St, being greatest for the batch reaction, less for the preswollen batch reaction, and least for the semibatch reaction. Upon aging the PBA core-polymer migrated out of the latex particles with a low degree of grafting to form dumbellshaped particles, whereas the PBA–PS core-shell particles with a high degree of grafting remained spherical because of the emulsifying ability of graft copolymer.     

Structure of minimum thickness and terraced free-standing films of block copolymers

The morphologies of thin, substrate-free block copolymer films have been examined by cross-sectional TEM. Two poly(styrene-b-butadiene) diblock copolymers were studied: one that forms PS cylinders and the other that forms PB cylinders in the bulk. Films were annealed while supported by metal TEM grids, embedded, and ultramicrotomed in crosssection. We find that at the metal support the film forms a meniscus-like region, or Plateau border, which exhibits the bulk morphology. Away from the border, the film thickness decreases and regions of terraced in-plane cylinder domains occur until a minimum thickness is reached. The minimum thickness region of the PB majority copolymer in cross-section shows a PS interlayer penetrated by a hexagonal array of circular PB channels that connect upper and lower PB surface layers, and a total thickness of 25–27 nm. The minimum thickness region of the PS majority copolymer in plan view shows no image contrast, but in cross-section reveals a continuous PS interlayer covered by layers of PB, and a total thickness of 20 nm. Comparisons with the chain dimensions suggest a bilayer arrangement for both morphologies with strongly perturbed chain conformations in the surface layers. © 1996 John Wiley & Sons, Inc.     

Monitoring surface thermal transitions of ABA triblock copolymers with crystalline segments using phase contrast tapping mode atomic force microscopy

Variable-temperature tapping mode atomic force microscopy was used to follow thermal transitions in nanoscale phase separated triblock copolymers containing partially crystalline poly(octadecyl methacrylate) or poly(docosyl methacrylate) and glassy (poly(tert-butyl acrylate)) segments. Melting/crystallization and devitrification/vitrification transitions in phase separated domains were followed with the aid of "phase shift thermograms" constructed from cantilever phase shift maps acquired at different temperatures. This type of analysis turned out to be particularly useful in following melting/crystallization and devitrification/vitrification transitions occurring in the same temperature range and thus difficult or impossible to resolve using differential scanning calorimetry.     

Atom‐transfer radical grafting polymerization of 2‐methacryloyloxyethyl phosphorylcholine from silicon wafer surfaces

2‐Methacryloyloxyethyl phosphorylcholine (MPC), a biomimetic monomer, was grafted from silicon wafer surfaces at room temperature by combining self‐assembly of initiator and surface‐initiated atom transfer radical polymerization. Two methods were used to control the grafting process. One was to add free initiator to the reaction system; the other was to add excess deactivator. The grafting densities up to 0.3 chains/nm² were obtained. The surface thickness increased linearly with MPC conversion. The thickness depended on catalyst and monomer concentrations, as well as activator/deactivator ratio. Poly(MPC) layers of >100 nm thick were obtained by optimizing the polymerization conditions. A second block of either poly(MPC) or poly[2‐(dimethylamino)ethyl methacrylate] was also grown from the grafted poly(MPC), demonstrating the system livingness. X‐ray photoelectron spectroscopy was used to examine the surface chemical compositions showed good agreement with the theoretical values. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2931–2942, 2004     

Morphological mapping and analysis of poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] and its clay nanocomposites by atomic force microscopy

Atomic force microscopy was successfully applied for comprehensive nanoscale surface and bulk morphological characterization of thermoplastic elastomeric triblock copolymers: poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) having different block lengths and their clay based nanocomposites. Commercially available Cloisite®20A and octadecyl (C₁₈) ammonium ion modified montmorillonite clay (OC) prepared in our laboratory by cation exchange reaction were used. The phase detected images in the tapping mode atomic force microscopy exhibited a well‐ordered phase separated morphology consisting of bright nanophasic domains corresponding to hard component and darker domains corresponding to softer rubbery ethylene‐co‐butylene (PEB) lamella for all the neat triblock copolymers. This lamellar morphology gave a domain width of 19–23 nm for styrenic nanophase and 12–15 nm for ethylene‐co‐butylene phase of SEBS having end to mid block length ratio of 30:70 and block molecular weights of 8800–41,200–8800. On increasing the ratio of block lengths of the polymer matrix and the selectivity of the solvent toward the blocks used for casting, the morphological features of the resultant films altered along with change in domain thickness. The phase images showed position and distribution of the brightest clay stacks in the dark‐bright contrast of the base matrix of the nanocomposite. Exfoliated and intercalated‐exfoliated morphology obtained in the case of Cloisite®20A and OC‐based SEBS nanocomposites, respectively, is further supported by X‐ ray diffraction and transmission electron microscopy studies. The lamellar thickness of the soft phases widened to 50–75 nm, where the layered clay silicates (40–54 nm in length and 4–17 nm in width) were embedded in the soft rubbery phases in the block copolymeric matrix of the nanocomposite. The marginally thicker width of the hard styrenic phases and slightly shrinked width of the soft rubbery lamella can be observed from the regions where no nanofiller is present. Distinct differences in bulk morphologies of the nanocomposites prepared in the melt and the solution processes were obtained with nanocomposites. The presence of clay particles was evident from the almost zero pull‐off and snap‐in force in the force‐distance analysis of SEBS based nanocomposite. This analysis also revealed stronger tip interaction resulting in highest contact and adhesive forces with the softer PEB region relative to the harder PS region. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 52–66, 2007     

Motion of integrated CdS nanoparticles by phase separation of block copolymer brushes

A new method of reversibly moving CdS nanoparticles in the perpendicular direction was developed on the basis of the phase separation of block copolymer brushes. Polystyrene-b-(poly(methyl methacrylate)-co-poly(cadmium dimethacrylate)) (PS-b-(PMMA-co-PCdMA)) brushes were grafted from the silicon wafer by surface-initiated atom transfer radical polymerization (ATRP). By exposing the polymer brushes to H2S gas, PS-b-(PMMA-co-PCdMA) brushes were converted to polystyrene-b-(poly(methyl methacrylate)-co-poly(methacrylic acid)(CdS)) (PS-b-(PMMA-co-PMAA(CdS))) brushes, in which CdS nanoparticles were chemically bonded by the carboxylic groups of PMAA segment. Alternating treatment of the PS-b-(PMMA-co-PMAA(CdS)) brushes by selective solvents for the outer block (a mixed solvent of acetone and ethanol) and the inner PS block (toluene) induced perpendicular phase separation of polymer brushes, which resulted in the reversible lifting and lowering of CdS nanoparticles in the perpendicular direction. The extent of movement can be adjusted by the relative thickness of two blocks of the polymer brushes.     

Multicomponent latex IPN materials. I. Morphology control

A series of novel structured latex particles with interpenetrating polymer network (IPN) cores and glassy SAN shells were developed in an attempt to investigate the feasibility of these polymers as both toughening and damping agents in thermoplastics. The IPN cores were composed of one impact part (polybutadiene based) and one damping part (acrylic based, with T_g around +10°C). The particle morphologies of these polymers were determined by TEM. The glass transitions and mechanical behavior of the polymers were characterized from DMS. The effect of different components on the final core/shell particle morphologies and mechanical properties was studied. The mechanical behavior of core/shell particles with IPN cores was also compared with that of separate core/shell and multilayered core/shell particles. In addition, normal core/shell synthesis (rubbery part first then the glassy part) and inverted core/shell synthesis (glassy part first then the rubbery part) were performed to provide another access for morphology control. It was found that the core/shell latex particles with poly(butyl acrylate) based copolymers are more miscible than poly(ethylhexyl methacrylate)-based copolymers. The high grafting efficiency of poly(butyl acrylate) plays an important role in governing phase miscibility. The latex particles synthesized by the inverted core/shell mode showed higher miscibility than the normal synthesized ones. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2193–2206, 1997     

Structural morphology of poly(styrene)-poly(butyl acrylate) polymer-polymer composites studied by dynamic mechanical measurements

The emulsion polymerization process allows production of polymer particles with different structural morphologies. Films obtained after coalescence keep some memory of this morphology, but large modifications can occur during coalescence. In the present case, one of the polymers, polystyrene (PS), exhibits a glass temperature (Tg) much higher than the filmification temperature (close to room temperature), while the other one, poly(butyl acrylate) (PBA), has a much lowerTg. Furthermore, it is well known that dynamic mechanical measurements can be very helpful in providing information on the morphology of polymer materials, i.e., on geometrical and topological arrangement of homopolymer domains. At first, this method was used for comparison of two types of films: i) the first one obtained from structured-core (PS)-shell (PBA) particles, ii) the second one obtained from a blend of homopolymer particles (PS and PBA). It appears that the expected core-shell particles lost their geometric structure in the second film. Second, comparison of the predicted dynamic modulus and experimental data shows that i) strong interactions exist between PS nodules unless their coalescence has occured, leading to an abnormally high modulus at room temperature, ii) after achieving their coalescence, PS forms a more or less continuous phase. Both phenomena strongly depend on the particle size and their respective volume fractions.     

Model of sorption of simple molecules in polymers

A model of simple molecule sorption in polymers is proposed which embraces both the glassy and rubbery regions, and incorporates the successful dual-mode model below the glass-transition temperature. Hole filling is shown to be an important sorption mechanism both above and below T_g, although saturation effects do not occur in the rubbery polymer. The model interprets the “dual-mode” Langmuir and Henry's law parameters at the molecular level, and a simple statistical mechanical analysis allows estimation of the parameter values, as well as specifying certain interrelationships between the parameters. Applications of the model to gas solubility data in five polymers are considered [polyethylene (PE), poly(ethylene terephthalate) (PET), polystyrene (PS), polymethacrylate (PMA), poly(vinyl acetate) (PVAc)] and semiquantitative agreement is obtained for PE, PET, and to a lesser extent, PS. For PMA and PVAc, the agreement is qualitative only.