Electrochemical Detection of Catechol on Boron‐doped Diamond Electrode Modified with Au/TiO2 Nanorod Composite

Au/TiO₂ nanorod composites with different ratios of [TiO₂]:[Au] have been prepared by chemically reducing AuCl₄^‐ on the positively charged TiO₂ nanorods surface and used to modify boron‐doped diamond (BDD) electrodes. The electrochemical behaviors of catechol on the bare and different Au/TiO₂ nanorod composites‐modified BDD electrodes are studied. The cyclic voltammetric results indicate that these different Au/TiO₂ nanorod composites‐modified BDD electrodes can enhance the electrocatalytic activity toward catechol detection, as compared with the bare BDD electrode. Among these different conditions, the Au/TiO₂‐BDD3 electrode (the ratio of [TiO₂]:[Au] is 27:1) is the most choice for catechol detection. The electrochemical response dependences of the Au/TiO₂‐BDD3 electrode on pH of solution and the applied potential are studied. The detection limit of catechol is found to be about 1.4 × 10^‐6 M in a linear range from 5 × 10^‐6 M to 200 × 10^‐6 M on the Au/TiO₂‐BDD3 electrode.     

Polythymine Oligonucleotide‐Modified Gold Electrode for Voltammetric Determination of Mercury(II) in Aqueous Solution

Polythymine oligonucleotide (PTO)‐modified gold electrode (PTO/Au) was developed for selective and sensitive Hg²⁺ detection in aqueous solutions. This modified electrode was prepared by self‐assembly of thiolated polythymine oligonucleotide (5′‐SH‐T₁₅‐3′) on the gold electrode via Au? S bonds, and then the surface was passivated with 1‐mercaptohexanol solution. The proposed electrode utilizes the specific binding interactions between Hg²⁺ and thymine to selectively capture Hg²⁺, thereby reducing the interference from coexistent ions. After exchanging the medium, electrochemical reduction at ?0.2 V for 60 s, voltammetric determination was performed by differential pulse voltammetry using 10 mM HEPES; pH 7.2, 1 M NaClO₄ as supporting electrolyte. This electrode showed increasing voltammetric response in the range of 0.21 nM Hg²⁺, with a relative standard deviation of 5.32% and a practical detection limit of 60 pM. Compared with the conventional stripping approach, the modified electrode exhibits good sensitivity and selectivity, and is expected to be a new type of green electrode.     

A Comparison of a Nanostructured Enzymeless Au/Fe2O3/MWCNTs/GCE Electrode and a GOx Modified One in Electrocatalytic Detection of Glucose

Acid functionalized multi‐walled carbon nanotubes (f‐MWCNTs) were decorated with Au and Fe₂O₃ nanoparticles (FeONPs) and deposited on glassy carbon electrode (GCE). The resulting hybrid Au/Fe₂O₃/f‐MWCNTs/GCE electrode and the one further modified by glucose oxidase were compared for detection of glucose. FeONPs and Au were deposited on the f‐MWCNTs by sonication‐assisted precipitation and deposition‐precipitation methods, respectively. The morphology and structure of the samples were characterized by transmission electron microscopy, scanning electron microscopy, X‐ray diffraction and Raman spectroscopy. A uniform distribution of FeONPs with an average size of 5 nm increased the surface area of functionalized nanotubes from 39 to 50 m²/g. The electrocatalytic glucose detection on the modified electrodes was evaluated using cyclic voltammetry and chronoamperometry in 0.1 M phosphate buffer solution at pH 7.0. The non‐enzymatic and enzymatic electrodes show sensitivity of 512.4 and 921.4 mA/mM.cm² and detection limit of 1.7 and 0.9 mM, respectively. The enzymatic and enzymeless electrodes retained more than 70 % and 80 % of their cathodic faradic current after 70 days, respectively. The sensing mechanism of the non‐enzymatic biosensor is described through the reaction of glucose with iron (III) ions, while in the case of enzymatic electrode, glucose is oxidized by glucose oxidase.     

Differential Pulse Voltammetric Determination of Selenocystine Using Selenium‐gold Film Modified Electrode

Differential pulse voltammetric determination of selenocystine (SeC) using selenium‐gold film modified glassy carbon electrode ((Se‐Au)/GC) is presented. In 0.10 mol?L^?1 KNO₃ (pH 3.20) solution, SeC yields a sensitive reduction peak at ?740 mV on (Se‐Au)/GC electrode. The peak current has a linear relationship with the concentration of SeC in the range of 5.0×10^?8–7.0×10^?4 mol?L^?1, and a 3σ detection limit of SeC is 3.0×10^?8 mol?L^?1. The relative standard deviation of the reduction current at SeC concentration of 10^?6 mol?L^?1 is 3.88% (n=8) using the same electrode, and 4.19% when using three modified electrodes prepared at different times. The content of SeC in the selenium‐enriched yeast and selenium‐enriched tea is determined. The total selenium in ordinary or selenium‐enriched tea is determined by DAN fluorescence method. The results indicate that in selenium‐enriched yeast about 20% of total selenium is present as SeC and in selenium‐enriched tea SeC is the major form of selenoamino acids. The total selenium content in selenium‐enriched tea soup is 0.09 μgSe/g accounting by 7% compared with that in selenium‐enriched tea. Hence, only a little amount of selenium is utilized by drinking tea, and most selenium still stay in tealeaf. Uncertainty are 22.4% and 16.1% for determination of SeC in selenium‐enriched yeast and selenium‐enriched tea by differential pulse voltammetry (DPV) on (Se‐Au)/GC electrode, respectively.     

Immobilization of Enzymes on the Nano‐Au Film Modified Glassy Carbon Electrode for the Determination of Hydrogen Peroxide and Glucose

A new enzyme‐based amperometric biosensor for hydrogen peroxide was developed relying on the efficient immobilization of horseradish peroxidase (HRP) to a nano‐scaled particulate gold (nano‐Au) film modified glassy carbon electrode (GC). The nano‐Au film was obtained by a chitosan film which was first formed on the surface of GC. The high affinity of chitosan for nano‐Au associated with its amino groups resulted in the formation of nano‐Au film on the surface of GC. The film formed served as an intermediator to retain high efficient and stable immobilization of the enzyme. H₂O₂ was detected using hydroquinone as an electron mediator to transfer electrons between the electrode and HRP. The HRP immobilized on nano‐Au film maintained excellent electrocatalytical activity to the reduction of H₂O₂. The experimental parameters such as the operating potential of the working electrode, mediator concentration and pH of background electrolyte were optimized for best analytical performance of amperometry. The linear range of detection for H₂O₂ is from 6.1×10^?6 to 1.8×10^?3 mol L^?1 with a detection limit of 6.1 μmol L^?1 based on signal/noise=3. The proposed HRP enzyme sensor has the features of high sensitivity (0.25 Almol^?1cm^?2), fast response time (t_90%≤10 s) and a long‐term stability (>1 month). As an extension, glucose oxidase (GOD) was chemically bound to HRP‐modified electrode. A GOD/HRP bienzyme‐modified electrode formed in this way can be applied to the determination of glucose with satisfactory performance.     

Electrochemical deposition of gold at liquid–liquid interfaces studied by thin organic film-modified electrodes

The unique physico-chemical properties of gold nanoparticles portrayed in their chemical stability, the size-dependent electrochemistry, and the unusual optical properties make them suitable modifiers of various surfaces used in the fields of optical devices, electronics, and biosensors. In this work we present two different methods to obtain metallic gold nanoparticles at a liquid–liquid interface, and to control their growth by adjusting the experimental conditions. Decamethylferrocene (DMFC), used as an oxidizable compound dissolved in an organic solvent that is spread as a thin film on the surface of graphite electrode, serves as a redox partner to exchange electrons across the liquid–liquid interface with the other redox counter-partner [AuCl₄]^? present in the conjoined water phase. The interfacial electron transfer between the DMFC and the [AuCl₄]^? ions leads to deposition of metallic gold nanoparticles at the liquid–liquid interface. The structure and features of the deposited Au nanoparticles were studied by means of microscopic and voltammetric techniques. The morphology of the Au deposit depends on the concentration ratio of redox partners and both electrode and liquid–liquid interfacial potential differences. Depending on whether the Au deposit was obtained by ex situ (at open circuit potential) or by “in situ” (by cycling of the electrode potential) approach, we observed quite different effects to the ion transfer reactions probed by the thin-film electrode set-up. The possible reasons for the different behavior of the Au nanoparticles are discussed in terms of the structure and the properties of the obtained Au deposit. In separate experiments, we have demonstrated catalytic effects of the Au nanoparticles towards enhancing the electron transfer between DMFC and two aqueous redox substrates, hexacyanoferrate and hydrogen peroxide.     

A Novel Enzymatic Glucose Biosensor and Nonenzymatic Hydrogen Peroxide Sensor Based on (3‐Aminopropyl) Triethoxysilane Functionalized Reduced Graphene Oxide

In the present study, a novel enzymatic glucose biosensor using glucose oxidase (GOx) immobilized into (3‐aminopropyl) triethoxysilane (APTES) functionalized reduced graphene oxide (rGO‐APTES) and hydrogen peroxide sensor based on rGO‐APTES modified glassy carbon (GC) electrode were fabricated. Nafion (Nf) was used as a protective membrane. For the characterization of the composites, Fourier transform infrared spectroscopy (FTIR), X‐ray powder diffractometer (XRD), and transmission electron microscopy (TEM) were used. The electrochemical properties of the modified electrodes were investigated using electrochemical impedance spectroscopy, cyclic voltammetry, and amperometry. The resulting Nf/rGO‐APTES/GOx/GC and Nf/rGO‐APTES/GC composites showed good electrocatalytical activity toward glucose and H₂O₂, respectively. The Nf/rGO‐APTES/GC electrode exhibited a linear range of H₂O₂ concentration from 0.05 to 15.25 mM with a detection limit (LOD) of 0.017 mM and sensitivity of 124.87 μA mM⁻¹ cm⁻². The Nf/rGO‐APTES/GOx/GC electrode showed a linear range of glucose from 0.02 to 4.340 mM with a LOD of 9 μM and sensitivity of 75.26 μA mM⁻¹ cm⁻². Also, the sensor and biosensor had notable selectivity, repeatability, reproducibility, and storage stability.     

Electrochemical application of titanium dioxide nanoparticle/gold nanoparticle/multiwalled carbon nanotube nanocomposites for nonenzymatic detection of ascorbic acid

Titanium dioxide nanoparticle/gold nanoparticle/carbon nanotube (TiO₂/Au/CNT) nanocomposites were synthesized, and then characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy (EDX). A TiO₂/Au/CNT nanocomposite-modified glassy carbon (GC) electrode was prepared using the drop coating method and was investigated using electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), differential pulse voltammetry (DPV), and amperometric current–time response (I-T). The modified material is redox-active. The nonenzymatically detected amount of ascorbic acid (AA) on the TiO₂/Au/CNT electrode showed a linear relationship with the AA concentration, for concentrations from 0.01 to 0.08 μM; the sensitivity was 117,776.36 μA?·?cm^?2?·?(mM)^?1, and the detection limit was 0.01 μM (S/N?=?3). The results indicated that the TiO₂/Au/CNT nanocomposite-modified GC electrode exhibited high electrocatalytic activity toward AA. This paper describes materials consisting of a network of TiO₂, Au, and MWCNTs, and the investigation of their synergistic effects in the detection of AA.     

Prussian Blue Modified Submicron Structured Gold Electrodes for Amperometric Hydrogen Peroxide Sensing

In this work, we present a simple and effective approach for fabricating sub‐micron structured gold (SM−Au) electrodes by chemically etching the magnetron co‐sputtered gold film in KI solution for certain time. Such electrodes with a large surface area to volume ratio were used as the matrix for electrochemical deposition of Prussian blue (PB) to develop an electrochemical hydrogen peroxide sensor. Experimental characterization using scanning electron microscope and atomic force microscope shows that the thickness of PB layer on SM−Au electrode is around 140 nm, and is composited with cubic PB nanocrystals. The electrochemical performance of the designed sensor, studied using cyclic voltammograms and chronoamperometry methods, suggests that the sensor based on SM−Au/PB electrode presents the direct electron transfer of PB particle towards SM−Au film, and exhibits fast response, wide linearity, low detection limit and high stability. Under the optimized conditions, the sensitivity of the developed sensor for the detection of H₂O₂ reaches the value of 512 mA cm⁻² M⁻¹ with a linear range from 1 μM to 4.5 mM.     

Immunosensors Based on Layer‐by‐Layer Self‐Assembled Au Colloidal Electrode for the Electrochemical Detection of Antigen

Colloidal Au particles have been deposited on the gold electrode through layer‐by‐layer self‐assembly using cysteamine as cross‐linkers. Self‐assembly of colloidal Au on the gold electrode resulted in an easier attachment of antibody, larger electrode surface and ideal electrode behavior. The redox reactions of [Fe(CN)₆]^4?/[Fe(CN)₆]^3? on the gold surface were blocked due to antibody immobilization, which were investigated by cyclic voltammetry and impedance spectroscopy. The interaction of antigen with grafted antibody recognition layers was carried out by soaking the modified electrode into a phosphate buffer at pH 7.0 with various concentrations of antigen at 37 °C for 30 min. Further, an amplification strategy to use biotin conjugated antibody was introduced for improving the sensitivity of impedance measurements. Thus, the sensor based on this immobilization method exhibits a large linear dynamic range, from 5–400 μg/L for detection of Human IgG. The detection limit is about 0.5 μg/L.     

Direct Electrochemistry of Glucose Oxidase at Carbon Nanotube‐gold Colloid Modified Electrode with Poly(diallyldimethylammonium chloride) Coating

Glucose oxidase showed direct electrochemical transfer at glassy carbon electrodes immobilized with carbon nanotube‐gold colloid (CNT‐Au) composites with poly(diallydimethylammonium chloride) (PDDA) coatings. The modified electrode (GC/CNT/Au/PDDA‐GOD) was employed for the amperometric determination of glucose. Under optimal conditions, the biosensor displayed linear response to glucose from 0.5 to 5 mM with a sensitivity of 2.50 mA M^?1 at an applied potential of ?0.3 V (vs. Ag|AgCl reference).     

Pulsed Amperometric Detection of Histamine at Glassy Carbon Electrodes Modified with Gold Nanoparticles

Gold nanocrystal‐modified glassy carbon electrodes (nAu‐GCE) were prepared and used for the determination of histamine by flow injection and high performance liquid chromatography using pulsed amperometric detection (PAD) as the detection mode. Experimental variables involved in the electrodeposition process of gold from a HAuCl₄ solution were optimized. A catalytic enhancement of the histamine voltammetric response was observed at the nAu‐GCE when compared with that obtained at a conventional Au disk electrode, as a consequence of the microdispersion of gold nanocrystals on the GC substrate. The morphological and electrochemical characteristics of the nAu‐GCE were evaluated by SEM and cyclic voltammetry. PAD using a very simple potential waveform consisting of an anodic potential (+700 mV for 500 ms) and a cathodic potential (?300 mV for 30 ms), was used to avoid the electrode surface fouling when histamine was detected under flowing conditions. Flow injection amperometric responses showed much higher I_p values and signal‐to‐noise ratios at the nAu‐GCE than at a conventional gold disk electrode. A limit of detection of 6×10^?7 mol L^?1 histamine was obtained. HPLC‐PAD at the nAu‐GCE was used for the determination of histamine in the presence of other biogenic amines and indole. Histamine was determined in sardine samples spiked at a 50 μg g^?1 concentration level, with good results. Furthermore, the chromatographic PAD method was also used for monitoring the formation of histamine during the decomposition process of sardine samples.     

Use of a Boron-Doped Diamond Electrode for Amperometric Assay of Bromide and Iodide Ions

The electrochemical assay of bromide and iodide ions at boron-doped diamond (BDD) electrode was investigated by cyclic voltammetry (CV) and chronoamperometry (CA). Comparison experiments were carried out using a glassy carbon (GC) electrode. The BDD electrode exhibited well-resolved and irreversible reduction voltammograms, while the GC electrode provided only an ill-defined response. Cyclic voltammetric signals at BDD electrode for 10 mM Br⁻ and I⁻ were observed at 561 and 125 mV vs. SCE; the values shifted negatively for 228.7 and 187.5 mV, respectively, compared to those at GC electrode. It was also found that the peak current of Br⁻ and I⁻ was in direct proportion to the scan rate, which is indicative of a surface confined reduction process. Sensitive amperometric responses for Br⁻ and I⁻ were obtained covering the linear ranges 0.666 μM–1 mM and 13.3 nM–1 mM, respectively, and their detection limits were 0.53 μM and 1.67 nM, respectively, under the optimum pH and applied potential. The amperometric response was very reproducible and stable with satisfactory recovery results. __________ From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 11, 2005, pp. 1193–1199. Original English Text Copyright ? 2005 by Jing Wu, Xiaoli Li, Cunxi Lei, Xumei Wu, Guoli Shen, and Rugin Yu. This article was submitted by the authors in English.     

Fabrication of New Magnetic Nanoparticles (Fe3O4) Grafted Multiwall Carbon Nanotubes and Heterocyclic Compound Modified Electrode for Electrochemical Sensor

Magnetic Fe₃O₄ nanoparticles functionalized multiwalled carbon nanotubes (nano‐Fe₃O₄ MWNTs) were prepared for electrochemical sensors. 2‐amino‐5‐mercapto‐1,3,4‐thiadiazole was used as a connecter to form a network that connected nano‐Fe₃O₄ MWNTs to the Au electrode surface. Modified process of the electrode was studied with SEM, TEM and cyclic voltammetry. Cyclic voltammetry and amperometric i‐t curve were used to investigate characteristics of the obtained electrode. The sensor has been successfully used on the direct detection of catechol and showed excellent performances. The linear regression equation was I_pa(μA)=0.07763+0.16739 C (μmol/L); R=0.9993 and the detection limit was 5.38×10^?8 mol/L. The modified electrode showed good reproducibility and stability.     

Electrochemical Behavior and Amperometric Detection of 4‐Chlorophenol on Nano‐Au Thin Films Modified Glassy Carbon Electrode

An amperometric sensor based on nano‐Au thin films was fabricated, by means of which a fast response to 4‐chlorophenol (4‐CP) can be achieved in the range of mM concentrations. The nanostructured Au thin film was prepared on glassy carbon electrodes by a template‐free, double‐potential step electrodeposition technique. Its structural feature can be controlled well by adjusting the deposition time. The amperometric detection of 4‐CP was performed at +0.85 V with a linear detection range from 0.2 to 4.8 mM and a detection limit of 0.11 mM (S/N=3). Besides, the effect of concentrations on the electrochemical behavior of 4‐CP on the Au thin film was investigated by linear sweep voltammetry, differential pulse voltammetry and electrochemical impedance spectroscopy.     

Amperometric Hydrogen Peroxide Biosensor Based on the Immobilization of Horseradish Peroxidase (HRP) on the Layer‐by‐Layer Assembly Films of Gold Colloidal Nanoparticles and Toluidine Blue

The precursor film was first formed on the Au electrode surface based on the self‐assembly of L ‐cysteine and the adsorption of gold colloidal nanoparticles (nano‐Au). Layer‐by‐layer (LBL) assembly films of toluidine blue (TB) and nano‐Au were fabricated by alternately immersing the electrode with precursor film into the solution of toluidine blue and gold colloid. Cyclic voltammetry (CV) and quartz crystal microbalance (QCM) were adopted to monitor the regular growth of {TB/Au} bilayer films. The successful assembly of {TB/Au}_n films brings a new strategy for electrochemical devices to construct layer‐by‐layer assembly films of nanomaterials and low molecular weight materials. In this article, {TB/Au}_n films were used as model films to fabricate a mediated H₂O₂ biosensor based on horseradish peroxidase, which responded rapidly to H₂O₂ in the linear range from 1.5×10^?7 mol/L to 8.6×10^?3 mol/L with a detection limit of 7.0×10^?8 mol/L. Morphologies of the final assembly films were characterized with scanning probe microscopy (SPM).     

Electrochemical Fabrication of Prussian Blue Nanocube‐decorated Electroreduced Graphene Oxide for Amperometric Sensing of NADH

In this study, Prussian blue (PB) film on the electroreduced graphene oxide (ERGO)‐modified Au electrode surface (ERGO/PB) is easily prepared by means of cyclic voltammetric technique in the mixture of K₃Fe(CN)₆ and FeCl₃. Its electrochemical behaviors for NADH biosensor are studied. The structural and morphological characters of modified electrode material are analyzed with using of XPS, XRD, Raman, EDS, and SEM techniques. ERGO/PB hybrid nanocomposite for NADH biosensor is exhibited to the higher catalytic effect (linear range from 1.0 to 100 μM, detection limit of 0.23 μM at S/N=3) compared to naked Au, ERGO‐modified Au, and PB‐modified Au electrodes. In addition to, ERGO/PB electrode was used to voltammetric and amperometric detection of H₂O₂. ERGO/PB electrodes also showed the same behavior as the NADH sensor. This ERGO/PB‐modified electrode supplied a simple, new, and low‐cost route for amperometric sensing of both NADH and H₂O₂.     

A Highly Sensitive Electrochemical Impedance Spectroscopy Immunosensor for Determination of 1‐Pyrenebutyric Acid Based on the Bifunctionality of Nafion/Gold Nanoparticles Composite Electrode

A simple, highly sensitive and label‐free electrochemical impedance spectroscopy (EIS) immunosensor was developed using Nafion and gold nanoparticles (nano‐Au/Nafion) composites for the determination of 1‐pyrenebutyric acid (PBA). Under the optimal conditions, the amount of immobilized antibody was significantly improved on the nano‐Au/Nafion electrode due to the synergistic effect and biocompatibility of Nafion film and gold nanoparticles composites. The results showed that the sensitivity and stability of nano‐Au/Nafion composite electrode for PBA detection were much better than those of nano‐Au modified glassy carbon electrode (nano‐Au/GCE). The plot of increased electron transfer resistances (R_ets) against the logarithm of PBA concentration is linear over the range from 0.1 to 150 ng·mL^?1 with the detection limit of 0.03 ng·mL^?1. The selectivity and accuracy of the proposed EIS immunosensor were evaluated with satisfactory results.     

Simultaneous Determination of Aluminum and Iron in High Salt Content Matrices by Adsorptive Stripping Voltammetry. Application to Dialysis Fluids

A new analytical procedure for the simultaneous determination of aluminum(III) and iron(II) in two kinds of dialysis fluids (peritoneal and hemodialysis fluids) by differential pulse adsorptive stripping voltammetry (DPAdSV) is described. The voltammetric measurements were performed using, as working electrode, a stationary mercury electrode, and a platinum electrode and a Ag|AgCl|KCl_(sat.) electrode as auxiliary and reference electrodes, respectively, employing acetate buffer solutions at different pH as supporting electrolyte. As complexing agents, Solochrome Violet RS, Palatine Chrome Black 6BN, Chromazurol S and Eriochrome Black T were employed. For both elements, the accuracy, expressed as relative recovery R%, was very satisfactory being in the range 94–105%, the precision as repeatability, expressed as relative standard deviation s_r%, was lower than 6%, while the limits of detection were of the order of a few units of μg/L. The analytical voltammetric procedure has been validated by comparison with spectroscopic (graphite furnace atomic absorption spectroscopy, GFAAS) measurements.     

A Zirconium Oxide Nanoparticle Modified Screen‐printed Electrode for Anodic Stripping Determination of Daclatasvir Dihydrochloride

A novel, sensitive and rapid voltammetric method applied for daclatasvir dihydrochloride (DSV.2HCl) detection in raw material, human plasma and urine using square wave voltammetry at a nano‐screen printed electrode (SPE) based on synthesized zirconium oxide nanoparticles (ZrO₂ NPs). The attention to zirconium oxide nanoparticle syntheses arises from its likely use in making an electrode material in the electroanalytical process. Anodic stripping square wave voltammetric peaks have been recorded at the optimum conditions of drug solution as pH, scan rate, accumulation time and accumulation potential. Morphology of the used nanoparticles has been performed by scanning electron microscope (SEM) and transmission microscope (TEM). ZrO₂ NPs were applied to screen printed electrode (ZrO₂‐MSPE) giving a new sensor to detect the DSV.2HCl drug. ZrO₂ NPs were tested for their electroactivity in improving electrodes sensitivity. The modified electrode has been used for the analysis of DSV.2HCl in spiked serum, spiked urine and pharmaceutical formulation.