Random poly(3‐hexylthiophene‐co‐3‐cyanothiophene‐co‐3‐(2‐ethylhexyl)thiophene) copolymers with high open‐circuit voltage in polymer solar cells

For the purpose of developing poly(3‐hexylthiophene) (P3HT) based copolymers with deep‐lying highest occupied molecular orbital (HOMO) levels for polymer solar cells with high open‐circuit voltage (V_oc), we report a combined approach of random incorporation of 3‐cyanothiophene (CNT) and 3‐(2‐ethylhexyl)thiophene (EHT) units into the P3HT backbone. This strategy is designed to overcome CNT content limitations in recently reported P3HT‐CNT copolymers, where incorporation of more than 15% of CNT into the polymer backbone leads to impaired polymer solubility and raises the HOMO level. This new approach allows incorporation of a larger CNT content, reaching even lower‐lying HOMO levels. Importantly, a very low HOMO level of ?5.78 eV was obtained, representing one of the lowest HOMO values for exclusively thiophene‐based polymers. Lower HOMO levels result in higher V_oc and higher power conversion efficiencies (PCE) compared to the previously reported P3HT‐CNT copolymers containing only 3‐hexylthiophene and CNT units. As a result, solar cells based on P3HT‐CNT‐EHT(15:15) , which contains 70% of P3HT, 15% of CNT and 15% of EHT, yield a V_oc of 0.83 V in blends with PC₆₁BM while preserving high fill factor (FF) and high short‐circuit current density (J_sc), resulting in 3.6% PCE. Additionally, we explored the effect of polymer number‐average molecular weight (M_n) on the optoelectronic properties and solar cell performance for the example of P3HT‐CNT‐EHT(15:15). The organic photovoltaic (OPV) performance improves with polymer M_n increasing from 3.4 to 6.7 to 9.6 kDa and then it declines as M_n further increases to 9.9 and to 16.2 kDa. The molecular weight study highlights the importance of not only the solar cell optimization, but also the significance of individual polymer properties optimization, in order to fully explore the potential of any given polymer in OPVs. The broader ramification of this study lies in potential application of these high band gap copolymers with low‐lying HOMO level in the development of ternary blend photovoltaics as well as tandem OPV. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1526–1536     

A New D–A conjugated polymer P(PTQD‐BDT) with PTQD acceptor and BDT donor units for BHJ polymer solar cells application

A novel donor–acceptor ( D–A ) copolymer comprising of weak electron donating BDT moiety and strong 9‐(2‐octyldodecyl)?8H‐pyrrolo[3,4‐b] bisthieno[2,3‐f:3',2'‐h] quinoxaline‐8,10(9H)‐dione (PTQD) unit denoted as P(PTQD‐BDT) was synthesized as donor material for polymer solar cells. P(PTQD‐BDT) shows a broad visible‐near‐infrared absorption band with an optical bandgap of 1.74 eV and possesses a relatively low‐lying HOMO level at ?5.28 eV. Bulk‐heterojunction polymer solar cell with the optimized blend of 1:2 (weight ratio) P(PTQD‐BDT):PC₇₁BM (processed with chloroform) shows an open circuit voltage of 0.92 V, a short circuit current density of 7.84 mA/cm², and a fill factor of 0.50, achieving a power conversion efficiency (PCE) of 3.61%. The PCE has been further improved to 5.55 % (J_sc = 10.34 mA/cm², V_oc = 0.88V and FF = 0.61), when 3% v ol 1,8‐diio‐dooctane (DIO) was used as solvent additive for the processing of P(PTQD‐BDT):PC₇₁BM blended film. The enhancement in J_sc is as a result of the appropriate morphology and efficient exciton dissociation into free charge carrier. The increase in PCE has been attributed to the favorable nanoscale morphology for efficient exciton dissociation and charge transport (reduction in the electron to hole mobility ratio). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2390–2398     

Enhanced properties of photovoltaic devices tailored with novel supramolecular structures based on reduced graphene oxide nanosheets grafted/functionalized with thiophenic materials

For verifying the influence of donor–acceptor supramolecules on photovoltaic properties, different hybrids were designed and used in organic solar cells. In this respect, reduced graphene oxide (rGO) was functionalization with 2‐thiophene acetic acid (rGO‐f‐TAA) and grafted with poly(3‐dodecylthiophene) (rGO‐g‐PDDT) and poly(3‐thiophene ethanol) (rGO‐g‐PTEt) to manipulate orientation of poly(3‐hexylthiophene) (P3HT) assemblies. Face‐on, edge‐on, and flat‐on orientations were detected for assembled P3HTs on rGO and its functionalized and grafted derivatives, respectively. Alteration of P3HT orientation from face‐on to flat‐on enhanced current density (J _sc), fill factor (FF), and power conversion efficiency (PCE) and thus J _sc = 7.11 mA cm^?2, FF = 47%, and PCE = 2.14% were acquired. By adding phenyl‐C71‐butyric acid methyl ester (PC71BM) to active layers composed of pre‐designed P3HT/rGO, P3HT/rGO‐f‐TAA, P3HT/rGO‐g‐PDDT, and P3HT/rGO‐g‐PTEt hybrids, photovoltaic characteristics further improved, demonstrating that supramolecules appropriately mediated in P3HT:PC71BM solar cells. Phase separation was more intensified in best‐performing photovoltaic systems. Larger P3HT crystals assembled onto grafted rGOs (95–143 nm) may have acted as convenient templates for the larger and more intensified phase separation in P3HT:PCBM films. The best performances were reached for P3HT:P3HT/rGO‐g‐PDDT:PCBM (J _sc = 9.45 mA cm^?2, FF = 54%, and PCE = 3.16%) and P3HT:P3HT/rGO‐g‐PTEt:PCBM (J _sc = 9.32 mA cm^?2, FF = 53%, and PCE = 3.11%) photovoltaic systems. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 1877–1889     

Synthesis and applications of a novel supramolecular polymer network with multiple H‐bonded melamine pendants and uracil crosslinkers

A conjugated main‐chain copolymer ( PBT ) consisting of bithiazole, dithieno[3,2‐b:2′,3′‐d]pyrroles (DTP), and pendent melamine units was synthesized by Stille polymerization, which can be hydrogen‐bonded (H‐bonded) with proper molar amounts of bi‐functional π‐conjugated crosslinker F (i.e., two uracil motifs covalently attached to a fluorene core through triple bonds symmetrically) to develop a novel supramolecular polymer network ( PBT/F ). The effects of multiple H‐bonds on light harvesting capabilities, HOMO levels, and photovoltaic properties of polymer PBT and H‐bonded polymer network PBT/F are investigated. The formation of supramolecular polymer network ( PBT/F ) between PBT and F was confirmed by FTIR and XRD measurements. Because of the stronger light absorption, lower HOMO level, and higher crystallinity of H‐bonded polymer network PBT/F , the solar cell device containing PBT/F showed better photovoltaic properties than that containing polymer PBT . The preliminary results show that the solar cell device containing 1:1 weight ratio of PBT/F and [6,6]‐phenyl C₇₁ butyric acid methyl ester (PC₇₁BM) offers the best power conversion efficiency (PCE) value of 0.86% with a short‐circuit current density (J_sc) of 4.97 mA/cm², an open circuit voltage (V_oc) of 0.55 V, and a fill factor (FF) of 31.5%. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Side chain engineering of naphthalene diimide–bithiophene‐based polymer acceptors in all‐polymer solar cells

Two novel polymeric acceptors based on naphthalene diimide (NDI) and 2.2′‐bithiophene, named as P(NDI2THD‐T2) and P(NDI2TOD‐T2), were designed and synthesized for all polymer solar cells application. The structural and electronic properties of the two acceptors were modulated through side‐chain engineering of the NDI units. The optoelectronic properties of the polymers and the morphologies of the blend films composed of the polymer acceptors and a donor polymer PTB7‐Th were systemically investigated. With thiophene groups introduced into the side chains of the NDI units, both polymers showed wider absorption from 350 nm to 900 nm, compared with the reference polymer acceptor of N2200. No redshift of absorption spectra from solutions to films indicated reduced aggregation of the polymers due to the steric hindrance effect of thiophene rings in the side chains. The photovoltaic performance were characterized for devices in a configuration of ITO/PEDOT:PSS/PTB7‐Th:acceptors/2,9‐bis(3‐(dimethylamino)propyl)anthra[2,1,9‐def:6,5,10‐def]diisoquinoline‐1,3,8,10(2H,9H)‐tetraone (PDIN)/Al. With the addition of diphenyl ether as an additive, the power conversion efficiencies (PCEs) of 2.73% and 4.75% for P(NDI2THD‐T2) and P(NDI2TOD‐T2) based devices were achieved, respectively. The latter showed improved J_sc, Fill Factor (FF), and PCE compared with N2200 based devices. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3679–3689     

Cyclometalated Ruthenium(II) Complexes Featuring Tridentate Click‐Derived Ligands for Dye‐Sensitized Solar Cell Applications

A series of heteroleptic bis(tridentate) Ru^II complexes featuring N^C^N‐cyclometalating ligands is presented. The 1,2,3‐triazole‐containing tridentate ligands are readily functionalized with hydrophobic side chains by means of click chemistry and the corresponding cyclometalated Ru^II complexes are easily synthesized. The performance of these thiocyanate‐free complexes in a dye‐sensitized solar cell was tested and a power conversion efficiency (PCE) of up to 4.0 % (J_sc=8.1 mA cm^?2, V_oc=0.66 V, FF=0.70) was achieved, while the black dye ((NBu₄)₃[Ru(Htctpy)(NCS)₃]; Htctpy=2,2′:6′,2′′‐terpyridine‐4′‐carboxylic acid‐4,4′′‐dicarboxylate) showed 5.2 % (J_sc=10.7 mA cm^?2, V_oc=0.69 V, FF=0.69) under comparable conditions. When co‐adsorbed with chenodeoxycholic acid, the PCE of the best cyclometalated dye could be improved to 4.5 % (J_sc=9.4 mA cm^?2, V_oc=0.65 V, FF=0.70). The PCEs correlate well with the light‐harvesting capabilities of the dyes, while a comparable incident photon‐to‐current efficiency was achieved with the cyclometalated dye and the black dye. Regeneration appeared to be efficient in the parent dye, despite the high energy of the highest occupied molecular orbital. The device performance was investigated in more detail by electrochemical impedance spectroscopy. Ultimately, a promising Ru^II sensitizer platform is presented that features a highly functionalizable “click”‐derived cyclometalating ligand.     

Fused structures in the polymer backbone to investigate the photovoltaic and electrochromic properties of donor–acceptor‐type conjugated polymers

In this study, two new benzotriazole (BTz) and dithienothiophene (DTT) containing conjugated polymers were synthesized. After successful characterizations of the monomers by proton‐nuclear magnetic resonance (¹H NMR) and carbon‐NMR (¹³C NMR) techniques, poly(4‐(dithieno[3, 2‐b:2′,3′‐d]thiophen‐2‐yl)‐2‐(2‐octyldodecyl)‐2H‐benzo[d][1,2,3] triazole) P1 and poly(4‐(5‐(dithieno[3,2‐b:2′,3′‐d]thiophen‐2‐yl)thiophen‐2‐yl)‐2‐(2‐octyldodecyl)‐7‐(thiophen‐2‐yl)‐2H‐benzo[d][1,2,3]triazole) P2 were synthesized via a typical Stille coupling. Electrochemical and spectroelectrochemical studies showed that both polymers can be multipurpose materials and used in electrochromic and photovoltaic applications. Reported study indicated that incorporation of DTT into the structure leads to fast switching times compared with BTz‐based polymers and competent percentage transmittance in the near‐infrared region. Multichromism is important in the context of low‐cost flexible display device technology and both polymers are ambipolar and processable as well as multichromic. Throughout the preliminary photovoltaic studies, the best performances of photovoltaic devices were found as V_oc = 0.49 V, J_sc = 0.83 mA/cm², fill factor (FF) = 34.4%, and power conversion efficiency (PCE) = 0.14% for P1 , and as V_oc = 0.35 V, J_sc = 1.57 mA/cm², FF = 38.2%, and PCE = 0.21% for P2 . © 2013 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Porphyrin–diindenothieno[2,3‐b]thiophene alternating copolymer—a blue‐light harvester in ternary‐blend polymer solar cells

Porphyrin, despite chosen by Nature as light harvesting units, hasn't revealed its full potentials as a structural unit in porphyrin‐incorporated polymers (PPors). A novel PPor was synthesized to investigate the origins of the low performances of PPor‐based polymer solar cells (PSCs). The polymer features broad absorption in the blue‐light region, because the diindenothieno[2,3‐b]thiophene (DITT) unit extended the conjugation in the polymer backbone. PPor‐DITT/PC₇₁BM based PSCs have a high V_oc (0.79 V). Their low J_sc and fill factor (FF) were attributed to the un‐optimized morphology, as indicated by the photoluminescence quenching and atomic force microscopy (AFM) experiments. Using PPor‐DITT as a blue‐light harvesting dopant in an amorphous host leverage the strong 400–550 nm absorption of PPor‐DITT and circumvent the difficulties in reaching optimized morphology in the PPor/PCBM thin films. An addition of 2 wt % of PPor‐DITT in ternary‐blend PSCs resulted in a 10 % increase of external quantum efficiency (EQE) in the blue‐light region. However, in a crystalline host, the dopant decreased the crystallinity of the host and led to large drops in FF and power conversion efficiencies (PCEs). The study provides an alternative route and expands the application of PPors in PSCs as a blue‐light harvester in ternary‐blend PSCs using amorphous polymers as host. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Anthracene‐Containing Wide‐Band‐Gap Conjugated Polymers for High‐Open‐Circuit‐Voltage Polymer Solar Cells

The synthesis, characterization, and photophysical and photovoltaic properties of two anthracene‐containing wide‐band‐gap donor and acceptor (D–A) alternating conjugated polymers ( P1 and P2 ) are described. These two polymers absorb in the range of 300–600 nm with a band gap of about 2.12 eV. Polymer solar cells with P1 :PC₇₁BM as the active layer demonstrate a power conversion efficiency (PCE) of 2.23% with a high V_oc of 0.96 V, a J_sc of 4.4 mA cm⁻², and a comparable fill factor (FF) of 0.53 under simulated solar illumination of AM 1.5 G (100 mW cm⁻²). In addition, P2 :PC₇₁BM blend‐based solar cells exhibit a PCE of 1.42% with a comparable V_oc of 0.89 V, a J_sc of 3.0 mA cm⁻², and an FF of 0.53.

     

Significantly improved photovoltaic performances of the dithiophene‐benzothiadiazole‐alt‐fluorene copolymers by incorporating carbazole units in fluorene moiety

To exploit an effective way to improve polymeric photovoltaic performance, a series of dithiophene‐benzothiadiazole‐alt‐fluorene copolymers containing carbazole groups at C‐9 positions of the alternating fluorene units (PFO‐FCz‐DBT) were synthesized and characterized. The effect of the carbazole groups on the optophysical, electrochemical, and photovoltaic properties of these copolymers was investigated. By comparison, this type of copolymers with carbazole units exhibited significantly improved photovoltaic properties than poly(2,7‐(9,9‐dioctyl‐fluorene)‐alt‐5,5‐(4′,7′‐di‐2‐thienyl‐2′,1′,3′‐benzothiadiazole) (PFO‐DBT) in the bulk heterojunction solar cells. A maximum power‐conversion efficiency (PCE) of 2.41% and a highest short‐circuit current density (J_sc) of 9.68 mA cm^?2 were obtained for the PFO‐FCz‐DBT30, which are about two times higher than the corresponding levels for the PFO‐DBT30. This work demonstrated that introducing a hole‐transporting carbazole unit into copolymer is a simple and effective method to improve the J_sc and PCE. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of indenofluorene‐based copolymers containing 2,5‐bis(2‐thienyl)‐N‐arylpyrrole for bulk heterojunction solar cells and polymer light‐emitting diodes

Two novel alternating π‐conjugated copolymers, poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(2,6‐diisopropylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P1 ) and poly[2,8‐(6,6′,12,12′‐tetraoctyl‐6,12‐dihydroindeno‐[1,2b]fluorene‐ alt‐5(1‐(p‐octylphenyl)‐2,5‐di(2‐thienyl)pyrrole) ( P2 ), were synthesized via the Suzuki coupling method and their optoelectronic properties were investigated. The resulting polymers P1 and P2 were completely soluble in various common organic solvents and their weight‐average molecular weights (M_w) were 5.66 × 10⁴ (polydispersity: 1.97) and 2.13× 10⁴ (polydispersity: 1.54), respectively. Bulk heterojunction (BHJ) solar cells were fabricated in ITO/PEDOT:PSS/polymer:PC₇₀BM(1:5)/TiO_x/Al configurations. The BHJ solar cell with P1 :PC₇₀BM (1:5) has a power conversion efficiency (PCE) of 1.12% (J_sc= 3.39 mA/cm², V_oc= 0.67 V, FF = 49.31%), measured using AM 1.5 G solar simulator at 100 mW/cm² light illumination. We fabricated polymer light‐emitting diodes (PLEDs) in ITO/PEDOT:PSS/emitting polymer:polyethylene glycol (PEG)/Ba/Al configurations. The electroluminescence (EL) maxima of the fabricated PLEDs varied from 526 nm to 556 nm depending on the ratio of the polymer to PEG. The turn‐on voltages of the PLEDs were in the range of 3–8 V depending on the ratio of the polymer to PEG, and the maximum brightness and luminance efficiency were 2103 cd/m² and 0.37 cd/A at 12 V, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3169–3177, 2010     

Ethynylene‐containing donor–acceptor alternating conjugated polymers: Synthesis and photovoltaic properties

Four ethynylene‐containing donor‐acceptor alternating conjugated polymers P1 – P4 with 2,5‐bis(dodecyloxy) substituted phenylene or carbazole as the donor unit and benzothiadiazole (BTZ) as the acceptor unit were synthesized and used as donor polymers in bulk heterojunction polymer solar cells. The optical, electrochemical, and photovoltaic properties of these four polymers with the ethylene unit located at different positions of the polymer chains were systematically investigated. Our results demonstrated that absorption spectra and the HOMO and LUMO energy levels of polymers could be tuned by varying the position of the ethynylene unit in the polymer chains. Photovoltaic devices based on polymer/PC₇₁BM blend films spin coated from chloroform and dichlorobenzene solutions were investigated. For all four polymers, open circuit voltages (V_oc) higher than 0.8 V were obtained. P4 , with ethynylene unit between BTZ and thiophene, shows the best performance among these four polymers, with a V_oc of 0.94 V, a J_sc of 4.2 mA/cm², an FF of 0.40, and a PCE of 1.6%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Enhanced efficiency of ternary organic solar cells by doping a polymer material in P3HT:PC61BM

Doping a low‐bandgap polymer material (PDTBDT‐DTNT) as a complementary electron donor in poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl‐C₆₁‐butyricacid methyl ester (PC₆₁BM) blend is experimented to improve the power conversion efficiency (PCE) of organic solar cells (OSCs). The PCE of OSCs was increased from 3.19% to 3.75% by doping 10 wt% PDTBDT‐DTNT, which was 17.55% higher than that of the OSCs based on binary blend of P3HT:PC₆₁BM (host cells). The short‐circuit current density (J_sc) was increased to 10.11 mA·cm⁻² compared with the host cells. Although the PCE improvement could partly be attributed to more photon harvest for complementary absorption of 2 donors by doping appropriate PDTBDT‐DTNT, the promotion of charge separation and transport as well as the suppression of charge recombination due to a matrix of cascade energy levels is also important. And the better morphology of the active layer films is beneficial to the optimized performance of ternary devices.     

Effect of substitution positions of alkyl side chains in phenanthrodithiophene–isoindigo copolymers: The enhancement of crystallinity and control of molecular orders

The synthesis, characterization, and solar cell application of newly developed two semiconducting polymers containing phenanthro[1,2‐b:8,7‐b′]dithiophene (PDT) and an isoindigo (IID) unit are described. In addition, a relationship between substitution position of side chains and molecular weights of the polymers and their solar cell performance are also discussed. Because of the installation of alkyl side chains onto sterically less hindered positions, PDT‐IID copolymers 12OD‐2 and 8OD‐2 have stronger intermolecular interaction than that of the previously reported copolymer 12OD . In low‐M_n polymers 12OD‐2 and 8OD‐2 formed high‐crystalline thin film with higher face‐on ratio than that of 12OD , but their unsuitable large‐scale phase separation suppressed their efficient photocurrent generation, leading to poor PCE of 2–3%. However, the surface morphology of 12OD‐2 and 8OD‐2 blended films are drastically improved by increasing M_n, which leads to the enhancement of J_sc and higher PCE of up to 4.3%. However, high‐M_n polymers 12OD‐2 and 8OD‐2 formed high‐crystalline film with about 10–15% lower face‐on ratio than that of high‐M_n polymer 12OD , leading to poor hole transporting ability, and thus lower J_sc and PCE. From this result, too much strong intermolecular interaction promotes the formation of unsuitable edge‐on orientation in blended films. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1757–1767     

Enhancement of photocurrent of polymer‐gelled dye‐sensitized solar cell by incorporation of exfoliated montmorillonite nanoplatelets

Poly(n‐isopropylacrylamide) (PNIPAAm) and its nanocomposite with exfoliated montmorillonite (MMT) were prepared by soap‐free emulsion polymerization and individually applied to gel the electrolyte systems for the dye‐sensitized solar cells (DSSCs). Each exfoliated MMT nanoplatelet had a thickness of ～ 1 nm, carried ～ 1.8 cation/nm², and acted like a two‐dimensional electrolyte. The DSSC with the LiI/I₂/tertiary butylpyridine electrolyte system gelled by this polymer nanocomposite had higher short‐circuit current density (J_sc) compared to that gelled by the neat PNIPAAm. The former has a J_sc of 12.6 mA/cm², an open circuit voltage (V_oc) of 0.73 V, and a fill factor (FF) of 0.59, which harvested 5.4% electricity conversion efficiency (η) under AM 1.5 irradiation at 100 mW/cm², whereas the latter has J_sc = 7.28 mA/cm², V_oc = 0.72 V, FF = 0.60, and η = 3.17%. IPCE of the nanocomposite‐gelled DSSC were also improved. Electrochemical impedance spectroscopy of the DSSCs revealed that the nanocomposite‐gelled electrolytes significantly decreased the impedances in three major electric current paths of DSSCs, that is, the resistance of electrolytes and electric contacts, impedance across the electrolytes/dye‐coated TiO₂ interface, and Nernstian diffusion within the electrolytes. The results were also consistent with the increased molar conductivity of nanocomposite‐gelled electrolytes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 47–53, 2008     

Benzotriazole and benzodithiophene containing medium band gap polymer for bulk heterojunction polymer solar cell applications

An alternating donor‐acceptor copolymer based on a benzotriazole and benzodithiophene was synthesized and selenophene was incorporated as π‐bridge. The photovoltaic and optical properties of polymer were studied. The copolymer showed medium band gap and dual absorption peaks in UV‐Vis absorption spectra. Photovoltaic properties of P‐SBTBDT were performed by conventional device structure. The OSC device based on polymer: PC₇₁BM (1:1, w/w) exhibited the best PCE of 3.60% with a V_oc of 0.67 V, a J_sc of 8.95 mA/cm², and a FF of 60%. This finding was supported with morphological data and space charge limited current (SCLC) mobilities. The hole mobility of the copolymer was estimated through SCLC model. Although surface roughness of the active layer is really high, mobility of a polymer was found as 7.46 × 10^?3 cm²/Vs for optimized device that can be attributed to Se?Se interactions due to the larger, more‐polarizable Se atom. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 528–535     

Effect of Device Fabrication Conditions on Photovoltaic Performance of Polymer Solar Cells Based on Poly(3‐hexylthiophene) and Indene‐C70 Bisadduct

Effect of the device fabrication conditions on photovoltaic performance of the polymer solar cells based on poly(3‐hexylthiophene) (P3HT) as donor and indene‐C₇₀ bisadduct (IC₇₀BA) as acceptor was studied systematically. The device fabrication conditions we studied include pre‐thermal annealing temperature, active layer thickness, and the P3HT:IC₇₀BA weight ratios. For devices with a 188‐nm‐thick active layer of P3HT:IC₇₀BA (1:1, w:w) blend film and pre‐thermal annealing at 150°C for 10 min, maximum power conversion efficiency (PCE) reached 5.82% with V_oc of 0.81 V, I_sc of 11.37 mA/cm², and FF of 64.0% under the illumination of AM1.5G, 100 mW/cm².     

Synthesis,characterization, and application to polymer solar cells of polythiophene derivatives with ester‐ or ketone‐substituted phenyl side groups

Four polythiophene derivatives including regiorandom polymers P1 , P2 , and P3 and a regioregular polymer P4 , containing a phenyl side chain with electron‐withdrawing carbonyl groups such as an ester and a ketone at the 3‐position of the thiophene ring, were synthesized by Stille coupling reaction. Bulk‐heterojunction polymer solar cells (PSCs) based on these polymers as p‐type semiconductors and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester (PCBM) were fabricated, and their photovoltaic performances were evaluated for the first time. The PSC devices based on the regioregular polymer P4 :PCBM = 1:2 (w/w) exhibited a high‐open‐circuit voltage (V_oc) of 0.943 V because of the low‐lying highest occupied molecular orbit energy level of P4 . The short π–π stacking distance (0.355 nm) in the parallel direction to the substrate and “face‐on” rich orientation were observed by the grazing incidence wide‐angle X‐ray scattering experiment, which might reflect higher J_sc and FF values of the P4 :[6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) PSC device than others. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 875–887     

New alternating D–A1–D–A2 copolymer containing two electron‐deficient moieties based on benzothiadiazole and 9‐(2‐Octyldodecyl)‐8H‐pyrrolo[3,4‐b]bisthieno[2,3‐f:3',2'‐h]quinoxaline‐8,10(9H)‐dione for efficient polymer solar cells

A novel D–A₁–D–A₂ copolymer denoted as P1 containing two electron withdrawing units based on benzothiadiazole (BT) and 9‐(2‐octyldodecyl)?8H‐pyrrolo[3,4‐b] bisthieno[2,3‐f:3′,2′‐h]quinoxaline‐8,10(9H)–dione (PTQD) units was synthesized and characterized. The resulting copolymer exhibits a broad‐absorption spectrum, relatively deep lying HOMO energy level (?5.44 eV) and narrow optical bandgap (1.50 eV). Bulk heterojunction (BHJ) polymer solar cells (PSCs) based on P1 as donor and PC₇₁BM as acceptor with optimized donor to acceptor weight ratio of 1:2 and processed with DIO/CB solvent showed good photovoltaic performance with power conversion efficiency of 6.21% which is higher than that of the device processed without solvent additive (4.40%). The absorption and morphology investigations of the active layers indicated that structural and morphological changes were induced by the solvent additive. This higher power conversion efficiency could be mainly attributed to the absorption enhancement and improved charge transported in the active layer induced by the better nanoscale morphology of the active layer. This study demonstrated that a copolymer with two different acceptor moieties in the backbone may be promising candidate as donor copolymer for solution processed BHJ PSCs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 155–168