Determination of bromide ions in seawater using flow system with chemiluminescence detection

A simple flow-based procedure with chemiluminescence (CL) detection is proposed for bromide ion determination in seawater. The procedure was based on the oxidation of bromide to bromine by chloramine-T followed by the reaction of bromine with luminol resulting in CL emission. Since no significant reaction within chloramine-T and luminol was observed, the detection was carried out without bromine extraction from the oxidant medium. The proposed flow system had a sampling rate of 40 determinations per hour, reagents consumption of 100 μg luminol and 60 μg chloramine-T per determination, a limit of detection of 0.5 mg l⁻¹ bromide ions, a linear concentration range (r = 0.999 and n = 7) between 0 and 100 mg l⁻¹, and a coefficient of variance better than 2.5% (for 10 measurements of a 10 mg l⁻¹ Br⁻ solution) were achieved. The analytical system was applied for the determination of bromide in seawater and estuarine-water samples, obtaining an analyte recovery ranging from 94 to 102% and comparing the results with a reference spectrophotometric method no significant difference was observed in 95% confidence level.     

Flow-injection chemiluminescence determination of chloroquine using peroxynitrous acid as oxidant

A new flow-injection chemiluminescence (CL) method for determination of chloroquine is proposed based on a stronger chemiluminescence of chloroquine in hydrogen peroxide-nitrite-sulfuric acid medium. The proposed method allows the measurement of chloroquine over the range of 3.0×10⁻⁷ to 1.0×10⁻⁵ mol l⁻¹. The detection limit is 8.6×10⁻⁸ mol l⁻¹, and the relative standard deviation for 1.0×10⁻⁶ mol l⁻¹ chloroquine (n=11) is 1.6%. The CL mechanism is also discussed.     

A portable and low cost equipment for flow injection chemiluminescence measurements

A compact, reliable and low cost flow injection chemiluminescence system is described. The flow system consists of a set of solenoid micro-pumps that can dispense reproductive micro-volumes of solutions. The luminometer was based on a coiled cell constructed from polyethylene tubing that was sandwiched between two large area photodiodes. The whole equipment costs about US$ 750 and weights ca. 3 kg. Equipment performance was evaluated by measuring low concentrations of hydrogen peroxide by oxidation of luminol and for the determination of ammonium, based on its inhibition of the luminescence provided by the reaction of luminol and sodium hypochlorite. Linear responses were achieved within 1.0-80 μmol L⁻¹ H₂O₂ and 0.6-60 μmol L⁻¹ NH₄⁺ with detection limits estimated as 400 nmol L⁻¹ H₂O₂ and 60 nmol L⁻¹ NH₄⁺ at the 99.7% confidence level. Coefficients of variation were 1.0 and 1.8%, estimated for 20 μmol L⁻¹ H₂O₂ and 15 μmol L⁻¹ NH₄⁺ (n = 20), respectively. Reagent consumption of 55 μg luminol, effluent volume of 950 μL per determination and sampling rate of 120 samples per hour were also achieved.     

Chemiluminometric photo-induced determination of Strychnine in a Multicommutation flow assembly

This paper deals on the determination of Strychnine, a potent and dangerous pesticide and the analytical procedure is based on the photo-induced chemiluminescence of the pesticide by means of the Multicommutation continuous-flow methodology. Small segments of the pesticide solution were sequentially alternated with segments of the solution for adjusting the suitable medium for the photodegradation. The required time of UV irradiation was obtained by stopped-flow during 150 s; then, the resulting solution formed alternated segments with the oxidizing solution containing 5 × 10⁻³ mol l⁻¹ Ce(IV) in 0.6 mol l⁻¹ nitric acid. The calibration range, from 2 μg l⁻¹ to 50 mg l⁻¹, resulted in a linear behaviour over the range 25 μg l⁻¹ to 20 mg l⁻¹ and fitting the equation: I = 4706x + 624 with a correlation coefficient of 0.9955. The limit of detection was 2 μg l⁻¹ and the sample throughput 15 h⁻¹. After testing the influence of a large series of potential interferents, the method was applied to different kinds of samples.     

Flow-injection chemiluminescence determination of fluoroquinolones by enhancement of weak chemiluminescence from peroxynitrous acid

A flow-injection chemiluminescence (CL) method is described for the determination of fluoroquinolones including ciprofloxacin, norfloxacin and ofloxacin. The method is based on the enhancement by these compounds of the weak CL from peroxynitrous acid. The linear ranges are 1.0×10⁻⁷ to 1.0×10⁻⁵ mol l⁻¹ for ciprofloxacin and norfloxacin, and 3.0×10⁻⁷ to 3.0×10⁻⁵ mol l⁻¹ for ofloxacin, respectively. The detection limits (S/N=3) are 4.5×10⁻⁸ mol l⁻¹ ciprofloxacin, 5.9×10⁻⁸ mol l⁻¹ norfloxacin and 1.1×10⁻⁷ mol l⁻¹ ofloxacin, respectively. The proposed method was applied to the determination of fluoroquinolones in pharmaceutical preparations.     

Flow-injection chemiluminescence determination of ascorbic acid by use of the cerium(IV)-Rhodamine B system

A highly sensitive flow-injection (FI) method with chemiluminescence (CL) detection is used for the determination of l-ascorbic acid. The method is based on the CL reaction of Rhodamine B with cerium(IV) in sulfuric acid media. l-Ascorbic acid is suggested to be a catalyst utilized in the energy-transferred excitation process. The proposed procedure allows quantitation of l-ascorbic acid in the range 3.8×10⁻¹³ to 1.0×10⁻¹⁰ mol l⁻¹ with a correlation coefficient of 0.9998 (n=5) and relative standard deviation (R.S.D.) of 0.92% (n=11) at 1.0×10⁻¹¹ mol l⁻¹. The detection limit (3×blank) was 1.0×10⁻¹³ mol l⁻¹. The method is successfully used to determine l-ascorbic acid in fresh vegetables. The possible mechanism of the chemiluminescence in the system is discussed.     

Analytical strategy photodegradation/chemiluminescence/continuous-flow multicommutation methodology for the determination of the herbicide Propanil

The present paper is dealing with an analytical strategy based on coupling photodegradation, chemiluminescence and multicommutation continuous-flow methodology for the determination of the pesticide Propanil, a common herbicide. The pesticide solution is inserted as small segments sequentially alternated with segments of the solution for adjusting the suitable medium for the photodegradation. Both flow-rates (sample and medium) are adjusted to required time for photodegradation, 2.0 min; and then, the resulting solution is also sequentially inserted as segments alternated with segments of the oxidizing solutions system, 1.00 × 10⁻⁴ mol l⁻¹ potassium permanganate in 2.00 mol l⁻¹ sulphuric acid medium. The calibration range, from 10 μg l⁻¹ to 25 mg l⁻¹, resulted in a linear behaviour over the range 10 μg l⁻¹-5 mg l⁻¹ and fitting the linear equation: I = 780.30C + 95.28; correlation coefficient 0.9999. The limit of detection was 8 μg l⁻¹ and the sample throughput 20 h⁻¹. After testing the influence of a large series of potential interferents the method is applied to water samples obtained from different places and to one formulation. The method is valid for the determination of other pesticides from the same chemical family, namely: alachlor, flumetsulam, furalaxyl and ofurace. Calibration graphs, limits of detection, repeatability and determination in water samples are obtained for each reported pesticide.     

Sensitive determination of captopril by flow injection analysis with chemiluminescence detection based on the enhancement of the luminol reaction

This work reports a novel flow injection (FI) method for the determination of captopril, 1-[(2S)-3-mercapto-2-methylpropionyl]-l-proline (CPL), based on the enhancement CPL affords on the chemiluminescence (CL) reaction between luminol and hydrogen peroxide. For this purpose alkaline luminol and hydrogen peroxide solutions were mixed online, the sample containing CPL was injected into an aqueous carrier stream, mixed with the luminol-hydrogen peroxide stream and pumped into a glass flow cell positioned in front of a photomultiplier tube (PMT). The increase in the CL intensity was recorded in the form of FI peaks, the height of which was related to the CPL mass concentration in the sample. Different chemical and instrumental parameters affecting the CL response were investigated. Under the selected conditions, the log-log calibration curve was linear in the range 5-5000 μg l⁻¹ of CPL, the limit of detection was 2 μg l⁻¹ (at the 3σ level), the R.S.D., s_r was 3.1% at the 100 μg l⁻¹ level (n=8) and the sampling rate was 180 injections h⁻¹. The method was applied to the determination of CPL in pharmaceutical formulations with recoveries in the range 100±3%.     

Rapid flow injection method for the determination of sulfite in wine using the permanganate-luminol luminescence system

A simple, rapid and sensitive chemiluminescence method for the determination of sulfite has been developed by combining flow-injection analysis and its sensitizing effect on the known chemiluminescence emission produced by the oxidation of luminol in alkaline medium; in this work permanganate has been proposed as oxidizing reactive. The optimum conditions for the chemiluminescence emission were established. The chemiluminescence was proportional to the sulfite concentration over the range 1.6 × 10⁻⁵ and 4.0 × 10⁻⁴ mol L⁻¹. The detection limit was 4.7 × 10⁻⁶ mol L⁻¹ of sulfite. The method has been satisfactorily used for the determination of free and bound sulfite in wines.     

A permeation liquid membrane system for determination of nickel in seawater

The use of a permeation liquid membrane system for the preconcentration and separation of nickel in natural and sea waters and subsequent determination by atomic absorption spectroscopy is presented. 2-Hydroxybenzaldehyde N-ethylthiosemi-carbazone (2-HBET) in toluene is used as the active component of the liquid membrane. A study strategy based on a simplex design has been followed. Several chemical and physical parameters were optimized. Maximum permeation coefficient was obtained at a feed solution pH of 9.4, 0.3 mol l⁻¹ of HNO₃ in the stripping solution and 1.66 mmol l⁻¹ of 2-HBTE in toluene as carrier. The precision of the method was 4.7% at 95% significance level and a detection limit of 0.012 μg l⁻¹ of nickel was achieved. The preconcentration procedure showed a linear response within the studied concentration range from 3 to 500 μg l⁻¹ of Ni in the feed solution. The method was validated with different spiked synthetic seawater and certified reference water samples: TMDA-62 and LGC 6016, without matrix interferences and showing good concordance with the certified values, being the relative errors −5.9% and −2.2%, respectively. Under optimal conditions, the average preconcentration yield for real seawater samples was 98 ± 5%, with a nickel preconcentration factor of 20.83 and metal concentrations ranging between 2.8 and 5.4 μg l⁻¹.     

Spectrophotometric catalytic determination of Fe(III) in estuarine waters using a flow-batch system

A flow-batch system was developed for the determination of Fe(III) in estuarine waters with high variability in salinity. The method is based on the catalytic effect of iron(III) on the oxidation rate of N,N-dimethyl-p-phenylenediammonium dichloride (DmPD) by hydrogen peroxide and the formed product is spectrophotometrically monitored at 554 nm. A controlled addition of sodium chloride to every assayed sample is accomplished for in-line individual salinity matching.The proposed system processes about 30 samples h⁻¹ and yields reproducible results. Relative standard deviations were estimated as <1.5% after 10 injections of typical samples (10.0-50.0 μg l⁻¹ Fe; ca. 0.5 mol l⁻¹ Cl). Synthetic samples (15.0 μg l⁻¹ Fe; 0.25-1.0 mol l⁻¹ NaCl) were efficiently processed, and no significant differences in results were found at a probability level of 99.7%. The method works for the full range of salinities. Only 120 μg DmPD are consumed per determination. The analytical curve is linear up to about 60 μg l⁻¹ Fe (r>0.999; n=5) and the detection limit is 5 μg l⁻¹ Fe. Results are in agreement with graphite furnace atomic absorption spectrometry.     

Rapid spectrophotometric determination of fosfestrol following on-line hydrolysis by alkaline phosphatase using flow injection and chasing zones

A new flow injection (FI) method is reported for the spectrophotometric determination of fosfestrol (diethyl-stilbestrol (DES) diphosphate) in pharmaceutical formulations. The proposed method is based on the on-line hydrolysis of the analyte by alkaline phosphatase (Al-Pase) using a “chasing zones” FI manifold. The orthophosphate ions, thus, generated are determined spectrophotometrically (λ_max=690 nm) using the molybdenum blue approach. The chemical and FI variables affecting the enzymatic reaction were investigated. The proposed method is very precise (s_r=1.1% at 1×10⁻⁴ mol l⁻¹ fosfestrol, n=12), fast (allowing up to 40 samples h⁻¹ to be analyzed) and has a determination range of 2×10⁻⁵ to 2×10⁻⁴ mol l⁻¹, with a satisfactory 3σ detection limit of 5×10⁻⁶ mol l⁻¹. The method was shown to provide accurate determinations of the fosfestrol concentration in a pharmaceutical formulation, giving relative errors, e_r, of +0.6 and −0.5% compared to the value stated by the supplier (Asta Medica Inc.) and the concentration derived using a method recommended by the United States Pharmacopoeia XXI, respectively. In addition, the average recoveries of known amounts of the analyte ranged between 99.2 and 101.2%.     

Chemiluminometric determination of carvedilol in a multi-pumping flow system

In this work a simple, fast, sensitive and selective flow-based procedure for the chemiluminometric determination of carvedilol, a recent non-cardioselective β-blocker with noteworthy antioxidant activity, is proposed. The developed methodology takes advantage of the antioxidant capacity of carvedilol to inhibit the chemiluminescence response resulting from the oxidation of luminol by hypochlorite, by acting as a hypochlorite scavenger. The analytical process was implemented in a multi-pumping flow system that employs multiple solenoid actuated micro-pumps as the only active components. These acted as solution insertion, propelling and commuting units assuring an easily controlled, low cost, compact and reliable analytical system.A linear working range for carvedilol concentrations ranging from 1.2 × 10⁻⁷ to 3.0 × 10⁻⁶ mol l⁻¹ (r > 0.999, n = 6), was obtained, with a detection limit of 8.7 × 10⁻⁹ mol l⁻¹. The system handles about 65 samples per hour yielding precise results (R.S.D. < 1.3%, n = 10). Recoveries within 95 and 104% were obtained.     

Electrochemical determination of maltol in beverages with glassy carbon electrode and its silica sol-gel modified electrode

The electrochemical behavior of maltol on a glassy carbon (GC) electrode was investigated. The results were applied to differential pulse voltammetric determination of maltol in beverages pretreated by ultrafiltration. Under the optimum experimental conditions, the linear range is 1×10⁻⁵ to 6×10⁻⁴ mol l⁻¹ maltol and the relative standard deviation for 0.4 mmol l⁻¹ maltol is 0.6% (n=9). The detection limit was 5 μmol l⁻¹. Furthermore, silica sol-gel film on GC electrode could be used as suitable selective membrane, which integrated selective membrane on the electrode and substituted for the pretreatment of ultrafiltration. Under the above conditions, maltol was determined by semi-differential linear sweep voltammetry at a silica sol-gel modified GC electrode in the concentration range of 5×10⁻⁶ to 5×10⁻⁴ mol l⁻¹. The detection limit was 2 μmol l⁻¹ and the relative standard deviation for 0.1 mmol l⁻¹ maltol was 0.7% (n=7). The proposed method is of sensitivity, simplicity, rapidness and no contamination. It had been applied to the direct determination of maltol in beverages such as grape wines, drinks and beers without any pretreatment. The results obtained with the present method were satisfactory with those obtained by spectrophotometry. It could be used as a simple and practical method for the determination of the flavor enhancer maltol in beverages.     

Determination of thyroxine hormone by luminol chemiluminescence

A chemiluminescence (CL) flow system for determination of thyroxine (Thy) is presented. It is based on the catalytic effect of cobalt(II) on the CL reaction between luminol and hydrogen peroxide. The iodinated chemical structure of Thy causes a heavy atom effect. The luminol CL signals show significant quenching by Thy. The calibration graph for Thy is linear for 15-70 μg ml⁻¹ and the 3σ detection limits are 27 μg ml⁻¹ for d-Thy and 23 μg ml⁻¹ for l-Thy.     

Determination of traces of palladium in stream sediment and auto catalyst by FI-ICP-OES using on-line separation and preconcentration with QuadraSil TA

A flow injection analysis (FIA) method using on-line separation and preconcentration with a novel metal scavenger beads, QuadraSil™ TA, has been developed for the ICP-OES determination of traces of palladium. QuadraSil TA contains diethylenetriamine as a functional group on spherical silica beads and shows the highest selectivity for Pd(II) at pH 1 (0.1 mol l⁻¹ hydrochloric acid) solution. An aliquot of the sample solution prepared as 0.1 mol l⁻¹ in hydrochloric acid was passed through the QuadraSil TA column. After washing the column with the carrier solution, the Pd(II) retained on the column was eluted with 0.05 mol l⁻¹ thiourea solution and the eluate was directly introduced into an ICP-OES. The proposed method was successfully applied to the determination of traces of palladium in JSd-2 stream sediment certified reference material [0.019 ± 0.001 μg g⁻¹ (n = 3); provisional value: 0.0212 μg g⁻¹] and SRM 2556 used auto catalyst certified reference material [315 ± 4 μg g⁻¹ (n = 4); certified value: 326 μg g⁻¹]. The detection limit (3σ) of 0.28 ng ml⁻¹ was obtained for 5 ml of sample solution. The sample throughputs for 5 ml and 100 μl of the sample solutions were 10 and 15 h⁻¹, respectively.     

Flow-injection investigation of the chemiluminescent reaction of bis(2,4,6-(trichlorophenyl)oxalate) with free chlorine

This work investigated the chemiluminescent reaction of free chlorine with bis(2,4,6-(trichlorophenyl)oxalate) (TCPO) in the presence of 9,10-diphenylanthracene in acetonitrile/water medium, with analytical application for free chlorine in tap water. In the absence of free chlorine, the background signal increased with the pH and the chemiluminescence emission showed strong dependence with the sample acidity. A flow injection analysis system, for free chlorine determination, was developed. The linear range for free chlorine was (0.2-3.0)×10⁻⁵ mol l⁻¹. Chloramine 1.0×10⁻⁵ mol l⁻¹ and chlorite 1.0×10⁻⁶ mol l⁻¹ also enhanced the chemiluminescence intensity.     

Amperometric sensor for nitrite using a glassy carbon electrode modified with alternating layers of iron(III) tetra-(N-methyl-4-pyridyl)-porphyrin and cobalt(II) tetrasulfonated phthalocyanine

The development of a highly sensitive amperometric sensor for nitrite using a glassy carbon electrode modified with alternated layers of iron(III) tetra-(N-methyl-4-pyridyl)-porphyrin (FeT4MPyP) and cobalt(II) tetrasulfonated phthalocyanine (CoTSPc) is described. The modified electrode showed an excellent catalytic activity and stability for the nitrite oxidation decreasing the peak potentials about 200 mV toward less positive values and presenting much higher peak currents than those obtained on the bare GC electrode. A linear response range of 0.2-8.6 μmol l⁻¹, with a sensitivity of 0.37 μA l μmol⁻¹ and detection limit of 0.04 μmol l⁻¹ were obtained with this sensor. The repeatability of the proposed sensor, evaluated in term of relative standard deviation, was verified to be 1.4% for 10 measurements of 0.2 μmol l⁻¹ nitrite solution. Interference caused by common ions has been investigated in simulated mixtures containing high concentration level of interfering ions and the sensor was found to be tolerant against these ions. The developed sensor was applied for the nitrite determination in water samples and the results were in agreement with those obtained by a comparative method described in the literature. The average recovery for these samples was 100.1 (±0.7)%.     

Flow-through solid-phase based optical sensor for the multisyringe flow injection trace determination of orthophosphate in waters with chemiluminescence detection

In this work, a novel flow-through solid-phase based chemiluminescence (CL) optical sensor is described for the trace determination of orthophosphate in waters exploiting the multisyringe flow injection analysis (MSFIA) concept with multicommutation. The proposed time-based injection flow system relies upon the in-line derivatisation of the analyte with ammonium molybdate in the presence of vanadate, and the transient immobilisation of the resulting heteropolyacid in a N-vinylpyrrolidone/divinylbenzene copolymer packed spiral shape flow-through cell located in front of the window of a photomultiplier tube. The simultaneous injection of well-defined slugs of luminol in alkaline medium and methanol solution towards the packed reactor is afterwards performed by proper switching of the solenoid valves. Then, the light emission from the luminol oxidation by the oxidant species retained onto the sorbent material is readily detected. At the same time, the generated molybdenum-blue compound is eluted by the minute amount of injected methanol, rendering the system prepared for a new measuring cycle. Therefore, the devised sensor enables the integration of the solid-phase CL reaction with elution and detection of the emitted light without the typical drawbacks of the molybdenum-blue based spectrophotometric procedures regarding the excess of molybdate anion, which causes high background signals due to its self-reduction. The noteworthy features of the developed CL-MSFIA system are the feasibility to accommodate reactions with different pH requirements and the ability to determine trace levels of orthophosphate in high silicate content samples (Si/P ratios up to 500). Under the optimised conditions, a dynamic linear range from 5 to 50 μg P l⁻¹ for a 1.8 ml sample, repeatability better than 3.0% and a quantification limit of 4 μg P l⁻¹ were attained. The flowing stream system handles 11 analysis h⁻¹ and has been successfully applied to the determination of trace levels of orthophosphate in environmental samples such as mineral, ground, tap and pond waters as well as samples from a water-steam cycle of an incineration plant. The t-test comparison of the means for the developed optical sensor and the molybdenum-blue spectrophotometric APHA/AWWA/WPCF reference method revealed that there is no evidence of significant differences between the obtained results at the 95% confidence level.     

Bia-amperometric quantification of salbutamol in pharmaceutical products

This paper presents a simple, rapid and reproducible method of analysis of salbutamol in pharmaceutical products, utilizing batch injection analysis (BIA) associated with amperometric detection. A study of salbutamol oxidation demonstrated a strong dependence between electrode fouling and pH. All determinations were done utilizing a glassy carbon electrode in presence of 3.0 mol l⁻¹ NaOH. A large linear dynamic range from 8×10⁻⁷ to 2×10⁻⁴ mol l⁻¹ was obtained by using an injected volume of 100 μl with a detection limit of 2.5×10⁻⁷ mol l⁻¹. R.S.D. of 0.92% for 50 successive injections of 4×10⁻⁶ mol l⁻¹ of salbutamol and a sample throughput of 60 samples per hour were achieved. The method was applied for salbutamol quantification in syrups.