Sulfur isotope enrichment in SF6 by high intensity CO2 laser radiation

Enrichment of ³⁴SF₆ following irradiation of SF₆?H₂ mixtures by the focused output of a pulsed TEA CO₂ laser has been studied as a function of the number of laser pulses, excitation wavelength, total pressure, and laser energy.     

Dynamics and correlated performance of a photo-triggered discharge-pumped HF laser using SF6 with hydrogen or ethane

3 , has been performed in Ne/SF₆/H₂ and Ne/SF₆/C₂H₆ mixtures. Parameters involved have been the storage line capacitance and the circuit inductance, the capacitors charging voltage, the RH-molecule type and partial pressure, and the X-ray dose for the preionization. High laser performance has been achieved with C₂H₆: an output energy up to 3 J corresponding to a specific energy of 9.6 J/l at an efficiency of 4.7%, which strengthens the advantage of the photo-triggering technique to energize high-power HF lasers. However the optimum performance achieved with H₂, 5.75 J/l and 3.5%, are lower. It is shown, through a time-resolved study of the electrical discharge and spatial dynamics correlated to laser power and energy measurements, that discharge instabilities are responsible for the poor laser performance of the mixture with H₂. These instabilities, which lead to arc development, are characteristics of the discharge in Ne/SF₆. It is demonstrated for the first time that addition of a heavy hydrocarbon, such as C₂H₆, to that mixture induces the discharge stabilization so that the laser emission arises in a homogeneous active medium. This effect allows us to achieve better laser performance than with H₂. Received: 17 March 1998/Revised version: 13 July 1998     

A KrF fast discharge laser in mixtures containing NF3, N2F4 or SF6

A fast discharge KrF laser system (λ = 248.5 nm) has been operated at 25 mJ/pulse, 3.0 MW peak power in high pressure He: Kr: fluoride mixtures containing low concentrations of both krypton and the fluorine donors N₂F₄, NF₃ and SF₆. Lasing action is reported for the first time in N₂F₄ and SF₆ with optimum energy output at 750 and 160 mJ/l respectively.     

Short delay time UV preionized TEA CO2 laser operating with binary CO2/H2 and CO2/He gas mixtures

In order to obtain short tail-free output laser pulses from a TEA CO₂ laser, parametric study of the laser operation with CO₂/H₂ and CO₂/He binary gas mixtures containing high CO₂ concentrations was carried out. A small scale UV preionized short delay time TEA CO₂ laser was employed. In terms of the maximum extractable output pulse energy and power, the more conventional CO₂/He gas mixture was found to be inferior in comparison with the CO₂/H₂ mixture proposed here.     

Importance of pre-ionisation for the non-chain discharge-pumped HF laser

The importance of pre-ionisation for the non-chain discharge-pumped HF laser is studied through experiments on an X-ray photo-triggered laser using mixtures of Ne, SF₆, and ethane. The discharge dynamic in Ne/SF₆ mixtures or pure SF₆, as well as the stabilisation effect induced by C₂H₆ and consequences for the laser performance, are investigated for pre-ionisation electron density values, n_eo, ranging from 10⁶ cm^-3 up to 10⁹ cm^-3, as well as for the so-called discharge self-breakdown mode. Without ethane, the minimum n_eo value which is needed to complete 100% homogeneous charge deposition in the plasma is a very sharply increasing function of the SF₆ pressure. This hinders performance optimisation when the molecule used to react with F-atoms, for instance H₂, has no effect on the discharge dynamic. The minimum ethane partial pressure that is needed to stabilise the discharge depends on n_eo, the pumping pulse duration, the deposited electric charge, and the SF₆ pressure. Discharges in Ne/SF₆ can be much more efficiently stabilised by addition of a small amount of ethane than by an increase of n_eo. A pre-ionisation density as low as 10⁶ cm^-3 is sufficient to achieve the maximum laser energy value, but total suppression of the pre-ionisation has a detrimental effect on the active medium homogeneity. Received: 30 May 2000 / Revised version: 9 October 2000 / Published online: 9 February 2001     

Observation of rotational population transfer effect for an HF chemical laser

When a CO₂ gas absorption cell was placed within the optical cavity of a low pressure pulsed HF laser, the specific vibration- rotation line of the HF laser disappeared, which influenced both the intensity and pulse duration of the neighbouring lines. This behavior strongly depends upon the rotational population transfer in HF. By measuring the time response of this behavior, it was found that the rate constant for the rotational population transfer was in the range of 10⁷ s^-1 torr^-1 for the SF₆/H₂ lasing mixture.     

Some aspects of CO2 laser induced fluorescence in SF6−H2 mixtures

Measurements in SF₆?H₂ mixtures of HF¹ fluorescence at 2.8 μm induced by pulsed CO₂ laser radiation are reported. The dependence of fluorescence intensity on laser fluence is found to be strongly affected by the laser beam geometry in the interaction region. Our results show that the technique of HF¹ fluorescence intensity detection can be a sensitive and reliable single-shot measure of multiple-photon dissociation of SF₆ in a collisionless regime on condition that the laser fluence is uniform along the interaction region which is monitored.     

The fluorescence and IR energy deposition from from CO2 laser irradiation of SF6−H2 mixtures

The multiple photon excitation and dissociation of SF₆ and hydrogen mixtures is measured by using simultaneously pulsed optoacoustic detection to monitor the energy deposition and time resolved HF fluorescence to monitor the production of vibrationally hot HF. From these studies we deduce that at least three mechanisms lead to production of vibrationally excited HF. One mechanism produces free F from the unimolecular laser-induced decomposition of SF₆. The second mechanism involves the reaction between two vibrationally hot SF₆ molecules to produce free F. In both of these cases the F atom subsequently react with H₂ to produce vibrationally hot HF. The third involves the reaction between a vibrationally hot SF₆ molecule and a hydrogen molecule producing vibrationally hot HF directly.     

High-efficiency,high-energy performance of a pulsed HF laser pumped by phototriggered discharge

A comparison of the performance of pulsed infrared HF lasers pumped by phototriggered discharges using either Ne/SF₆/H₂ or Ne/SF₆/C₂H₆ mixtures are presented. For an active volume of 50 cm³, a specific output energy as high as 11 J/ has been achieved with an efficiency higher than 3% when C₂H₆ is used as H atom fuel. The replacement of ethane by molecular hydrogen reduces the laser performance by 40%. The investigation of the temporal evolution of the laser intensity shows that this dramatic decrease results from a shortening of the laser pulse duration rather than from a decrease of the peak power. Indications are given that this behavior is correlated to a very different temporal evolution of the discharge parameters, especially at low reduced electric field E/N.     

Spectroscopic studies of UV production from ARC sources in iodine laser gas mixtures

Time-integrated spectral measurements of the light from multiple arc sources in iodine laser gas mixtures (He:SF₆:i-C₃F₇I and Ar:SF₆:i-C₃F₇I) are described. Copious soft-UV output, fully sufficient as a pump source, is observed with no adverse decrease in UV production for i-C₃F₇I concentrations as high as 3% by volume. Conversion efficiencies of 3–4% for stored electrical energy into UV radiation within the iodide compound band were determined.     

CO2 laser CVD of a-Si:H: in situ gas analysis and model calculations

4 and disilane Si₂H₆ induced by continuous wave CO₂ laser irradiation has been investigated under the conditions of chemical vapor deposition (CVD) of amorphous hydrogenated silicon a-Si:H. At the very position of depositing the thin film the stationary chemical composition of the processing gas is probed in situ by an effusive molecular beam which passes through a differential pumping stage into a quadrupole mass spectrometer (QMS). With SiH₄ as educt and SF₆ as a sensitizer, SiH₄ and Si₂H₆ are found in the processing gas while Si₃H₈ or higher silanes are lacking. Si₂H₆ and SF₆ lead to SiH₄, Si₂H₆, and Si₃H₈, but higher silanes are missing. The experimentally determined composition of the processing gas is semi-quantitatively reproduced by model calculations based on the assumption of stationary local equilibrium conditions and applying thermodynamic and spectroscopic data (molecular statistics). The mass balance of the processing gas entering and leaving the CVD chamber states an atomic ratio Si:H of 1:2 for the gas phase species forming the solid deposit on the reactor walls. This finding together with theoretical considerations indicates the intermediate Si₂H₄ to be the dominating gas phase species forming the a-Si:H thin films. Received: 17 July 1998/Accepted: 20 July 1998     

Efficiency of an electron-beam-pumped chemical laser with an SF6-H2 working mixture

Results are presented from a study of HF lasers pumped by non-chain chemical reactions initiated by a radially convergent and by a planar electron beam. The main channels of formation of vibrationally excited HF molecules are analyzed. The distribution of the energy density of the radiation in the output beam of a wide-aperture laser is measured. In 30 liters of a mixture of SF₆:H₂=8:1 at a pressure of 1.1 atm an output energy of ∼200 J is obtained at an ∼11% efficiency with respect to the energy deposition. It is shown that the admixture of a buffer gas of neon or argon improves the uniformity of the radiation energy distribution in the output beam of an HF laser pumped by a non-chain chemical reaction and initiated by an electron beam, and it also increases the output energy. Zh. Tekh. Fiz. 69, 76–81 (January 1999)     

Comparison of the first negative corona current pulses in N2 + SF6 and CO2 + SF6 mixtures

The current waveforms of the first negative corona pulses in a small point-to-plane gap have been measured with a nanosecond time resolution in N₂ + SF₆ and CO₂ + SF₆ mixtures at a pressure 50 kPa for various contents of SF₆ as a function of applied gap voltages. The physical mechanism for the pulses in these mixtures with low concentration of SF₆ has been described using the streamer-based theory. The influence of changing admixtures of SF₆ in N₂ and CO₂ has been compared. Differences in the pulse waveforms observed in N₂- and CO₂-based gas mixtures are explained by differences in the first and second Townsend ionization coefficients. This work was supported by the Grant Agency VEGA from the Ministry of Education of Slovak Republic under contracts 1/1011/04 and 1/2017/05.     

电激励脉冲HF激光SF_6/C_2H_6工作气体的放电特性

研究了电激励脉冲HF激光工作介质SF6/C2H6混合气体的放电特性。通过对放电等离子体荧光图像和放电波形的测量,分析比较了不同条件下放电稳定性、剩余电压、能量沉积效率等特性参数的变化情况。实验结果表明:混合气体的放电过程存在主放电、剩余电压维持和电弧放电3个阶段,各阶段的放电特性有所差异;提高充电电压有利于放电能量的有效沉积,也会使不稳定的电弧放电提前;增加C2H6原子分数能起到抑制电弧放电的作用;混合气体总压的增加会导致剩余电压的提高以及辉光放电的能量沉积效率的降低;最佳的能量沉积出现在电弧放电阶段与辉光放电阶段即将融合的临界状态。     

Spectroscopic study of a TEA CO2 laser of the CO2/X,X=H2; N2/H2 type

The spectral output of a TEA CO₂ laser utilizing nonconventional CO₂/H₂ and CO₂/N₂/H₂ gas mixtures was analysed. A simultaneous multiline output in P-branch of the 00°110°0 transition was recorded. A domination of the P(18) line is typical for the first, and that of the P(20) line for the second gas mixture. The enhancement of the P(18) line intensity in spectra (different from P(20) line domination-CO₂/N₂/H₂ mixture) is explained primarily by a smaller contribution of the R(23) line gain (01¹111¹0 CO₂ band), to P(20) line (00°110°0 band). All measurements were conducted with a nondispersive optical cavity.     

High power self-controled volume discharge based molecular lasers

An investigation was made of the characteristics of the formation of a selfcontroled volume discharge for the pumping of CO₂ lasers, i.e. self-sustained volume discharge (SSVD), which involved a preliminary filling of a discharge gap by an electron flux from an auxiliary-discharge plasma. We have found that this method was suitable for large interelectrode gaps, that distortion of the electric field in the gap by the space charge of the electron flux played an important role in the formation of the discharge and that the electrodes could be profiled dynamically during propagation of an electron flux through the discharge gap and a SSVD could form in systems with a strongly inhomogeneous field. High power SSVD based CO₂ laser systems have been created and investigated. Another type of self-controled volume discharge without pre-ionization, i.e. a selfinitiated volume discharge (SIVD), in nonchain HF lasers with SF₆−C₂H₆ mixtures was investigated as well in our review. We have established that, after the primary local electrical breakdown of the discharge gap, the SIVD spreads along the gap in directions perpendicular to that of the electric field by means of the successive formation of overlapping diffuse channels under a discharge voltage close to its quasi-steady state value. It is shown that, as new channels appear, the current flowing through the channels formed earlier decreases. The volume occupied by the SIVD increases with increase in the energy deposited in the plasma and, when the discharge volume is confined by a dielectric surface, the discharge voltage increases simultaneously with increase in the current. The possible mechanisms which explain the observed phenomena, namely the dissociation of SF₆ molecules and electron attachment SF₆ molecules, are examined. A simple analytical model, which makes it possible to describe these mechanisms at a qualitative level, was developed. High power SIVD based HF(DF) lasers have been developed and tested.     

Multiband CO2 oscillator

Multiband output from an atmospheric CO₂ laser has been achieved with intercavity gaseous absorbers. SF₆, NH₃, NH₂D and butane are suitable for this purpose.     

Collision-induced simultaneous transitions in H2+CF4 and H2+SF6 mixtures

The simultaneous transitions of the v₃ fundamental vibrations of CF₄ and SF₆ with the fundamental Q branch and S(1) line of H₂ have been studied for various H₂+CF₄ and H₂+SF₆ mixtures at total pressures up to 185 bars. The integrated intensities are found to be proportional to the partial densities of the gas mixture components. The agreement between experimental and calculated intensities is generally better for the Kihara potential than for the Lennard-Jones potential.     

紧凑的非链式脉冲HF激光器

研究了气体组分和峰化电容对紫外光预电离脉冲HF激光器性能的影响.实验发现最佳气体混合比为SF₆/C₂H₆=20:1,峰化电容和主放电电容的最佳比为C_p/C_s=0.3,在最佳气体混合比时,最大激光脉冲峰值功率和对应的总气压随充电电压的提高而增大.同时得到了E/P值和激光能量的关系.整个器件的最大激光输出为400mJ,脉冲峰值功率为1.5MW,最大电光转换效率约为2.2%.