剪切作用下Cu(100)扭转晶界塑性行为研究

本文采用分子动力学方法研究了在剪切载荷作用下,Cu(100)扭转晶界对Cu柱屈服强度的影响.模拟结果发现,在加载过程中,低角度扭转晶界形成的位错网发生位错形核与扩展,位错之间的塞积作用提高了Cu柱的屈服强度;对于高角度扭转晶界,晶界发生滑动降低了Cu柱的屈服强度.同时发现,随着扭转角度的增加,Cu柱的屈服强度先增大,当扭转角度大于临界角度时,Cu柱的屈服应力逐渐减小.这表明剪切载荷作用下,两种不同的机理主导Cu柱的屈服,对于小于临界角度的扭转晶界,Cu柱的屈服由晶界位错形核和扩展机理主导,对于大于临界角度 关键词： 扭转晶界 分子动力学 位错形核 晶界滑移     

Stimulation and Suppression of Grain Boundary Sliding by Intragranular Slip in Zinc Bicrystals

The influence of intragranular slip on grain boundary sliding is studied in originally compatible zinc bicrystals with symmetric tilt boundary. The experiment is designed to separate different effects of intragranular slip on the boundary sliding and establish their mechanisms. Grain boundary sliding with and without development of intragranular slip is observed. The rate of sliding accompanied by slip is more than five times of that without slip. A good correlation between the boundary sliding and intragranular slip prior to slide hardening is established. Slide hardening followed by the negative sliding near one end of the boundary and strain hardening in the boundary vicinity, are observed at the last stages of deformation. For the case of formation of slip induced glissile grain boundary dislocations of opposite signs the possibility of their contribution to total grain boundary sliding, is analyzed. The effect of the increase in the rate of sliding is explained in terms of the accommodation of sliding by slip and appearance of additional glissile grain boundary dislocations of one sign due to strain incompatibility. Contribution of these different dislocation mechanisms to the increase in the sliding rate is determined for the stage of deformation preceding slide hardening. It is supposed that the effect of slide hardening and negative sliding as well as boundary curving is created by non-smooth boundary and small degree of incompatibility caused by straining.     

Effect of grain boundary sliding on the toughness of ultrafine grain structure steel: A molecular dynamics simulation study

Molecular dynamics simulations are carried out to investigate the mechanisms of low-temperature impact toughness of the ultrafine grain structure steel. The simulation results suggest that the sliding of the {001}/{110} type and {110}/{111} type grain boundary can improve the impact toughness. Then, the mechanism of grain boundary sliding is studied and it is found that the motion of dislocations along the grain boundary is the underlying cause of the grain boundary sliding. Finally, the sliding of the grain boundary is analyzed from the standpoint of the energy. We conclude that the measures which can increase the quantity of the {001}/{110} type and {110}/{111} type grain boundary and elongate the free gliding distance of dislocations along these grain boundaries will improve the low-temperature impact toughness of the ultrafine grain structure steel.     

Grain boundary sliding during ambient-temperature creep in hexagonal close-packed metals

Even at ambient temperature or less, below their 0.2% proof stresses all hexagonal close-packed metals and alloys show creep behaviour because they have dislocation arrays lying on a single slip system with no tangled dislocation inside each grain. In this case, lattice dislocations move without obstacles and pile-up in front of a grain boundary. Then these dislocations must be accommodated at the grain boundary to continue creep deformation. Atomic force microscopy revealed the occurrence of grain boundary sliding (GBS) in the ambient-temperature creep region. Lattice rotation of 5° was observed near grain boundaries by electron backscatter diffraction pattern analyses. Because of an extra low apparent activation energy of 20 kJ/mol, conventional diffusion processes are not activated. To accommodate these piled-up dislocations without diffusion processes, lattice dislocations must be absorbed by grain boundaries through a slip-induced GBS mechanism.     

Kinetics of Grain Boundary Recovery in Deformed Polycrystals

Annealing kinetics are studied for nonequilibrium ensembles of dislocations occurring in grain boundaries during plastic deformation. Two types of dislocation ensembles are considered: 1) walls of sessile extrinsic grain boundary dislocations (EGBDs), which cause a change of the GB misorientation angle, and 2) arrays of glissile EGBDs having a Burgers vector tangential to the grain boundary plane. For both types similar exponential relationships are obtained for the relaxation of the average EGBD density, with approximately the same characteristic time proportional to the cube of grain size.     

Grain boundary sliding and lattice dislocation emission in nanocrystalline materials under plastic deformation

A theoretical model is proposed to describe the physical mechanisms of hardening and softening of nanocrystalline materials during superplastic deformation. According to this model, triple interface junctions are obstacles to glide motion of grain boundary dislocations, which are carriers of grain boundary glide deformation. Transformations of an ensemble of grain boundary dislocations that occur at triple interface junctions bring about the formation of partial dislocations and the local migration of triple junctions. The energy characteristics of these transformations are considered. Pileups of partial dislocations at triple junctions cause hardening and initiate intragrain lattice sliding. When the Burgers vectors of partial dislocations reach a critical value, lattice dislocations are emitted and glide into adjacent grains, thereby smoothing the hardening effect. The local migration of triple interface junctions (caused by grain boundary sliding) and the emission of lattice dislocations bring about softening of a nanocrystalline material. The flow stress is found as a function of the total plastic strain, and the result agrees well with experimental data.     

Generation of Electrical Currents and Magnetic Fields by Grain Boundary Motion

The effect of an induced magnetic moment due to grain boundary motion in a magnetic field was studied theoretically in a microscopic and a mesoscopic approximation. It was found that the induced moment generates a drag force on the boundary, which depends on the orientation of the magnetic field with regard to the crystal axis, as observed experimentally. However, the magnitude of the theoretically predicted dependency is much smaller than experimentally observed and even opposite with regard to the orientation dependence. Therefore, the electromagnetic drag can be neglected in comparison with other driving forces for grain boundary motion, but the effect may play a role for fast moving dislocations in a magnetic field.     

Grain Growth During Superplastic Deformation

Significant grain growth occurring during superplastic deformation is related to the micro-mechanism of superplastic flow. Observations performed on the deformed surface of superplastically deformed tensile and shear Pb-62%Sn samples and bi-axially formed AA7475 samples directly indicate that cooperative grain boundary sliding, i.e. sliding of grain groups, is accompanied by cooperative grain boundary migration that can result in an enhanced grain growth. Such a long range correlation in migration of sliding grain boundaries is related to movement of grain boundary dislocations having a step associated with its core. Observed correlation between grain size and strain measured in different regions of a superplastically formed Ti-alloy part and alignment of grain boundaries along shear surfaces support coupling of grain boundary sliding and migration. A model of grain growth considering climb of cellular dislocations, topological defects in a grain array, has been expanded to incorporate gliding and mixed cellular dislocations.     

Coupled motion of [10−10] tilt boundaries in magnesium bicrystals

Magnesium bicrystals were grown with symmetric and asymmetric tilt boundaries about the [10–10] axis using the vertical Bridgman technique. Isothermal constant load tensile tests were conducted on these bicrystals in the temperature range 300–500°C and relative displacements of the two grains were measured to obtain an appreciation for grain boundary motion characteristics. Coupled grain boundary motion was noted in almost all cases with the degree of tangential motion versus migration changing with tilt misorientation, temperature and applied stress. Specifically, within the family of symmetric bicrystals evaluated, a minimum in grain boundary displacement in the specimen plane was observed at a tilt misorientation of 20°. In specific stress/temperature regimes, rigid body sliding was observed for the particular case of a 35° asymmetric tilt misorientation. The ease of basal and prism slip in magnesium at the temperatures considered and the consequential impingement of intragranular dislocations on the bicrystal boundary and their decomposition and motion along the boundary are thought to play an important role in the observed coupled motion of these tilt boundaries.     

Strain induced grain boundary premelting in bulk copper bicrystals

In bulk bicrystals strain induced grain boundary premelting (SIGBPM) occurs when heavy screw dislocation pileup can be held up to a certain high temperature, approximately 0.6T _M, where T _M is the melting point of bulk material in Kelvin. SIGBPM occurs at grain boundaries to which new twist component is added due to the rotation of both component crystals toward opposite direction about the axis perpendicular to the grain boundary plane. At the original grain boundary, grain boundary sliding takes place due to this relative rotation. In f.c.c. metals with relatively low stacking fault energies such as copper, nickel, brass(30Zn) and silver, dislocations dissociate into partials. Therefore high density tangled dislocations introduced during plastic deformation hardly loose. If these dislocations can be held to high temperatures, SIGBPM is promoted. Formation of static or dynamic recrystallized grains suppresses SIGBPM itself and the propagation of grain boundary cracks formed by SIGBPM.     

Effect of solute atoms on grain boundary sliding in magnesium alloys

The effect of solid-solution alloying on grain boundary sliding (GBS) was investigated using pure magnesium and six kinds of Mg–X (X?=?Ag, Al, Li, Pb, Y and Zn) dilute binary solid solutions with an average grain size of 10?µm. A sharp increase in damping capacity caused by GBS was observed above a certain temperature. The temperature at which a sharp increase in damping capacity occurred depended on the alloying element. The addition of Y and Ag markedly increased the onset temperature (more than 100?K) for a sharp increase in damping capacity, whereas the addition of Zn, Al and Li slightly increased the onset temperature (less than 50?K) as compared with that for pure magnesium. Tensile tests at a temperature of 423?K revealed that the higher the onset temperature, the lower the strain rate sensitivity of the flow stress. It is suggested that the former elements (Y and Ag) are more effective in suppressing GBS in magnesium alloys than the latter ones (Zn, Al and Li). The suppression of GBS was associated with low grain boundary energy, and the extent to which the energy is reduced depended on the alloying element. It was suggested that the change in the lattice parameter (the so-called c/a ratio) affects the grain boundary energy, and thus, the occurrence of GBS.     

Quantifying the grain boundary resistance against slip transfer by experimental combination of geometric and stress approach using stage-I-fatigue cracks

In recent studies, many groups have investigated the interaction of dislocations and grain boundaries by bi-crystals and micro-specimen experiments. Partially, these experiments were combined with supplementary simulations by discrete dislocation dynamics, but quantitative data for the grain boundary resistance against slip transfer is still missing. In this feasibility study with first results, we use stage-I-fatigue cracks as highly localised sources for dislocations with well-known Burgers vectors to study the interaction between dislocations in the plastic zone in front of the crack tip and selected grain boundaries. The stress concentration at the grain boundary is calculated with the dislocation-free zone model of fracture using the dislocation density distribution in the plastic zone from slip trace height profile measurements by atomic force microscopy. The grain boundary resistance values calculated from common geometric models are compared to the local stress distribution at the grain boundaries. Hence, it is possible to quantify the grain boundary resistance and to combine geometric and stress approach for grain boundary resistance against slip transfer to a self-contained concept. As a result, the prediction of the grain boundary resistance effect based on a critical stress concept is possible with knowledge of the geometric parameters of the grain boundary only, namely the orientations of both participating grains and the orientation of the grain boundary plane.     

Diffusion along the Grain Boundaries in Crystals with Dislocations

A generalization of the Fisher model of the grain boundary diffusion is suggested, which takes into account the diffusion along short circuit diffusion paths (i.e., dislocations) in the bulk of crystalline grains. For the B-regime of the grain boundary diffusion, three different penetration modes have been found: at the short times the penetration depth of the element diffusing along the grain boundary is given by the Whipple solution of the Fisher model, but with the pipe diffusion coefficients along the dislocation cores instead of the volume diffusivities; at the intermediate times the penetration depth is a weak function of time, and at the large times the penetration depth again increases with time according to the Whipple solution, however, the rate of this increase is much smaller than in the initial period of time. The applications of the model for diffusion in nanomaterials are discussed.     

晶界对纳米多晶铝中冲击波阵面结构影响的分子动力学研究

用分子动力学方法研究了纳米多晶铝在冲击加载下的冲击波阵面结构及塑性变形机理.模拟研究结果表明:在弹性先驱波之后,是晶界间滑移和变形主导了前期的塑性变形机理;然后是不全位错在界面上成核和向晶粒内传播,然后在晶粒内形成堆垛层错、孪晶和全位错的过程主导了后期的塑性变形机理.冲击波阵面扫过之后留下的结构特征是堆垛层错和孪晶留在晶粒内,大部分全位错则湮灭于对面晶界.这个由两阶段塑性变形过程导致的时序性塑性波阵面结构是过去未见报道过的. 关键词： 晶界 塑性变形 冲击波阵面 分子动力学     

The Effect of Triple Junctions on Grain Boundary Motion and Grain Microstructure Evolution

The theory of steady state motion of grain boundary sytems with triple junctions and the main features of such systems are considered. A special technique of in-situ observations and recording of triple junction motion is introduced, and the results of experimental measurements on Zn tricrystals are discussed. It is shown, in particular, that the described method makes it possible to measure the triple junction mobility. It was found that the measured shape of a moving half-loop with a triple junction agrees with theoretical predictions. A transition from triple junction kinetics to grain boundary kinetics was observed. This means that triple junctions can drag boundary motion. It is demonstrated that the microstructural (granular) evolution is slowed down by triple junction drag for any n-sided grain. The second consequence pertains to six-sided grains. For a boundary system with dragging triple junctions there is no unique dividing line between vanishing and growing grains with respect to their topological class anymore, like n = 6 in the Von Neumann-Mullins relation.     

Nanocrystalline gold with small size: inverse Hall–Petch between mixed regime and super-soft regime

ABSTRACT

Molecular dynamics simulations were used to study the atomic mechanisms of deformation of nanocrystalline gold with 2.65–18?nm in grain size to explore the inverse Hall–Petch effect. Based on the mechanical responses, particularly the flow stress and the elastic-to-plastic transition, one can delineate three regimes: mixed (10–18?nm, dislocation activities and grain boundary sliding), inverse Hall-Petch (5–10?nm, grain boundary sliding), and super-soft (below 5?nm). As the grain size decreases, more grain boundaries present in the nanocrystalline solids, which block dislocation activities and facilitate grain boundary sliding. The transition from dislocation activities to grain boundary sliding leads to strengthening-then-softening due to grain size reduction, shown by the flow stress. It was further found that, samples with large grain exhibit pronounced yield, with the stress overshoot decrease as the grain size decreases. Samples with grain sizes smaller than 5?nm exhibit elastic-perfect plastic deformation without any stress overshoot, leading to the super-soft regime. Our simulations show that, during deformation, smaller grains rotate more and grow in size, while larger grains rotate less and shrink in size.     

Grain Boundary Dynamics: A Novel Tool for Microstructure Control

The reaction of grain boundaries to a wide spectrum of forces is reviewed. Curvature, volume energy and mechanical forces are considered. The boundary mobility is strongly dependent on misorientation, which is attributed to both grain boundary structure and segregation. In magnetically anisotropic materials grain boundaries can be moved by magnetic forces. For the first time a directionality of boundary mobility is reported. Flat boundaries can also be moved by mechanical forces, which sheds new light on microstructure evolution during elevated temperature deformation. Curvature driven and mechanically moved boundaries can behave differently. A sharp transition between the small and large angle boundary regime is observed. It is shown that grain boundary triple junctions have a finite mobility and thus, may have a serious impact on grain growth in fine grained materials. The various dependencies can be utilized to influence grain boundary motion and thus, microstructure evolution during recrystallization and grain growth.     

Grain boundary interdiffusion in the case of concentration-dependent grain boundary diffusion coefficient

The grain boundary diffusion in a binary system which exhibits a grain boundary phase transition is considered in the framework of Fisher's model. The kinetic law of the growth of the grain boundary phase and the distribution of the diffusant near the grain boundary are calculated. The method of determining of the concentration dependence of the grain boundary diffusion coefficient from the experimentally measured penetration profiles of the diffusant along the grain boundaries is suggested. The experimental results on Zn diffusion in Fe(Si) bicrystals, Ni diffusion in Cu bicrystals and grain boundary grooving in Al in the presence of liquid In are discussed in light of the suggested model.