Heat transfer from laminar flow in ducts with elliptic cross-section

Summary The cooling of a hot fluid in laminar Newtonian flow through cooled elliptic tubes has been calculated theoretically. Numerical data have been computed for the two values 1.25 and 4 of the axial ratio of the elliptic cross-section . For =1.25 the influence of non-zero thermal resistance between outmost fluid layer and isothermal surroundings has also been investigated. Special attention has been given to the distribution of heat flux around the perimeter; when increases the flux varies more with the position at the circumference. This positional dependence becomes less pronounced, however, as the (position-independent) thermal resistance of the wall increases.Flattening of the conduit, while maintaining its cross-sectional area constant, improves the cooling. Comparison with rectangular pipes shows that this improvement is not as marked with elliptic as with rectangular pipes.Nomenclature A _k =A _{m, n} coefficients of expansion (6) - a, b half-axes of ellipse, b<a - a _p =a _{r, s} coefficients of representation (V) - D hydraulic diameter, = 4S/P; S = cross-sectional area, P = perimeter - D _e equivalent diameter, according to (13) - n coordinate (outward) normal to the tube wall - T temperature of fluid - T _i temperature of fluid at the inlet - T _s temperature of surroundings - v ₀ mean velocity of fluid - v _z longitudinal velocity of fluid - x, y carthesian coordinates coinciding with axes of ellipse - z coordinate in flow direction - , dimensionless half-axes of ellipse, =a/D and =b/D - _t heat transfer coefficient from fluid at bulk temperature to surroundings; equation (11) - _w heat transfer coefficient at the wall; equation (3) - axial ratio of ellipse, = a/b = / - , , , dimensionless coordinates; =x/D, =y/D, =z/D, =n/D - dimensionless temperature, = (T–T _s)/(T _i–T _s) - ₀ cup-mixing mean value of ; equation (10) - thermal conductivity of fluid - _m,n = _k eigenvalue - c volumetric heat capacity of fluid - _{m, n} = _k = _k eigenfunction; equations (6) and (I) - Nu total Nusselt number, = _t D/ - Nusselt number at large distance from the inlet - Nu _w wall Nusselt number, = _w D/, based on _w - Pé Péclet number, = ₀ Dc/     

On the closure problem for Darcy's law

In a previous derivation of Darcy's law, the closure problem was presented in terms of an integro-differential equation for a second-order tensor. In this paper, we show that the closure problem can be transformed to a set of Stokes-like equations and we compare solutions of these equations with experimental data. The computational advantages of the transformed closure problem are considerable.Roman Letters A interfacial area of the- interface contained within the macroscopic system, m² - A _e area of entrances and exits for the-phase contained within the macroscopic system, m² - A interfacial area of the- interface contained within the averaging volume, m² - A _e area of entrances and exits for the-phase contained within the averaging volume, m² - B second-order tensor used to respresent the velocity deviation - b vector used to represent the pressure deviation, m^–1 - C second-order tensor related to the permeability tensor, m^–2 - D second-order tensor used to represent the velocity deviation, m² - d vector used to represent the pressure deviation, m - g gravity vector, m/s² - I unit tensor - K C ^–1,–D, Darcy's law permeability tensor, m² - L characteristic length scale for volume averaged quantities, m - characteristic length scale for the-phase, m - l _i i=1, 2, 3, lattice vectors, m - n unit normal vector pointing from the-phase toward the-phase - n _e outwardly directed unit normal vector at the entrances and exits of the-phase - p pressure in the-phase, N/m ² - p intrinsic phase average pressure, N/m² - p –p , spatial deviation of the pressure in the-phase, N/m² - r position vector locating points in the-phase, m - r ₀ radius of the averaging volume, m - t time, s - v velocity vector in the-phase, m/s - v intrinsic phase average velocity in the-phase, m/s - v phase average or Darcy velocity in the \-phase, m/s - v –v , spatial deviation of the velocity in the-phase m/s - V averaging volume, m³ - V volume of the-phase contained in the averaging volume, m³ Greek Letters V /V volume fraction of the-phase - mass density of the-phase, kg/m³ - viscosity of the-phase, Nt/m²     

Anlaufkorrektur und Elastizität bei der Kapillarströmung von Lösungen

Zusammenfassung Aus der Anlaufkorrektur kann man nach einer Rechnung vonFromm, die auf dem Maxwellschen Modell basiert, eine Relaxationszeit und eine korrigierte Viskosität _c ermitteln. Der Quotient _c/ stellt einen Schermodul dar. Diese Größe wird für Lösungen von Cellulosetrinitrat in Butylacetat, Polyvinylacetat in Dioxan, Polystyrol in Toluol, Polyacrylamid in Wasser, und Viskose, in Abhängigkeit von der Konzentrationc und dem SchergefälleD ermittelt. Es zeigt sich, daß _c/ etwa im Wendepunkt der Fließkurven eine Art Plateau oder ein flaches Maximum zeigt und in diesem Plateaubereich eine lineare Abhängigkeit von der Konzentration. Die absolute Größe von _c/ ist jedoch um Größenordnungen geringer, als sie nach der Formel vonRouse bzw.Bueche für die erste Relaxationszeit eines Verhängungsnetzwerkes zu erwarten wäre. Das wird so gedeutet, daß bei dem hohen Schergefälle, das bei den Messungen herrschte (D etwa 10⁴ sec^–1), ein Teil der Verhängungen zerstört ist, wodurch die Relaxationszeit vergrößert und der Schermodul verkleinert wird.

---

Summary From the end-correction, according to a calculation byFromm based upon theMaxwell-model, a relaxation time and a corrected viscosity _c can be obtained. The quotient _c/ represents a shear modulus. Its value is determined for solutions of cellulosetrinitrate in butylacetate, polyvinylacetate in dioxane, polystyrene in toluene, polyacryloamide in water, and viscose, in dependence of concentrationc and shear rateD. It is found, that _c/ shows a plateau or a flat maximum at the inflection point of the flow curves. In this range, a linear dependence on concentration is found too. The absolute value of _c/, however, is smaller by orders of magnitude than that to be expected for the first relaxation time of an entanglement network according to the formulas byRouse resp.Bueche. This is explained by a partial disruption of entanglements in the high shear rate prevailing at the experiments (D about 10⁴ sec^–1), which effects an increase of the relaxation time and a decrease of the shear modulus.

---

---

Vorgetragen auf der Jahrestagung der Deutschen Rheologen in Bad Ems vom 18.–19. Mai 1967.     

Transport in ordered and disordered porous media V: Geometrical results for two-dimensional systems

In this paper we continue the geometrical studies of computer generated two-phase systems that were presented in Part IV. In order to reduce the computational time associated with the previous three-dimensional studies, the calculations presented in this work are restricted to two dimensions. This allows us to explore more thoroughly the influence of the size of the averaging volume and to learn something about the use of anon-representative region in the determination of averaged quantities.

Nomenclature

Roman Letters A interfacial area of the– interface associated with the local closure problem, m² - a _i i=1, 2, gaussian probability distribution used to locate the position of particles - l unit tensor - characteristic length for the-phase particles, m - ⁰ reference characteristic length for the-phase particles, m - characteristic length for the-phase, m - _i i=1,2,3 lattice vectors, m - m convolution product weighting function - m _V special convolution product weighting function associated with a unit cell - n _i i=1, 2 integers used to locate the position of particles - n unit normal vector pointing from the-phase toward the-phase - r _p position vector locating the centroid of a particle, m - r gaussian probability distribution used to determine the size of a particle, m - r ₀ characteristic length of an averaging region, m - V averaging volume, m³ - V volume of the-phase contained in the averaging volume,V, m³ - x position of the centroid of an averaging area, m - x ₀ reference position of the centroid of an averaging area, m - y position vector locating points in the-phase relative to the centroid, m Greek Letters V /V, volume average porosity - _{a i} standard deviation ofa _i - _r standard deviation ofr - intrinsic phase average of      

The theory of a vibrating-rod densimeter

The paper presents a theory of a device for the accurate determination of the density of fluids over a wide range of thermodynamic states. The instrument is based upon the measurement of the characteristics of the resonance of a circular section tube, or rod, performing steady, transverse oscillations in the fluid. The theory developed accounts for the fluid motion external to the rod as well as the mechanical motion of the rod and is valid over a defined range of conditions. A complete set of working equations and corrections is obtained for the instrument which, together with the limits of the validity of the theory, prescribe the parameters of a practical design capable of high accuracy.Nomenclature A, B, C, D constants in equation (60) - A _j , B _j constants in equation (18) - a _j ⁺ , a _j ^– wavenumbers given by equation (19) - C _f drag coefficient defined in equation (64) - C _f ^/0 , C _f ^/1 components of C _f in series expansion in powers of - c speed of sound - D _b drag force of fluid b - D ₀ coefficient of internal damping - E extensional modulus - force per unit length - F _j ⁺ , F _j ^– constants in equation (24) - f, g functions of defined in equations (56) - G modulus of rigidity - I second moment of area - K constant in equation (90) - k, k constants defined in equations (9) - L half-length of oscillator - Ma Mach number - m _a mass per unit length of fluid a - m _b added mass per unit length of fluid b - m _s mass per unit length of solid - n _j eigenvalue defined in equation (17) - P power (energy per cycle) - P _a , P _b power in fluids a and b - p pressure - R radius of rod or outer radius of tube - R _c radius of container - R _i inner radius of tube - r radial coordinate - T tension - T _visc temperature rise due to heat generation by viscous dissipation - t time - v _r , v radial and angular velocity components - y lateral displacement - z axial coordinate - dimensionless tension - _a dimensionless mass of fluid a - _b dimensionless added mass of fluid b - _b dimensionless drag of fluid b - dimensionless parameter associated with - ₀ dimensionless coefficient of internal damping - dimensionless half-width of resonance curve - dimensionless frequency difference defined in equation (87) - spatial resolution of amplitude - R, , , _s , increments in R, , , _s , - dimensionless amplitude of oscillation - dimensionless axial coordinate - ratio of to - _a , _b ratios of to for fluids a and b - angular coordinate - parameter arising from distortion of initially plane cross-sections - _f thermal conductivity of fluid - dimensionless parameter associated with - viscosity of fluid - _a , _b viscosity of fluids a and b - dimensionless displacement - _j jth component of - density of fluid - _a , _b density of fluids a and b - _s density of tube or rod material - density of fluid calculated on assumption that * - dimensionless radial coordinate - * dimensionless radius of container - dimensionless times - _{rr rr}, _r radial normal and shear stress components - spatial component of defined in equation (13) - _j jth component of - dimensionless streamfunction - ⁰, ¹ components of in series expansion in powers of - phase angle - _r phase difference - _ra , _rb phase difference for fluids a and b - streamfunction - _j jth component defined in equation (22) - dimensionless frequency (based on ) - _a , _b dimensionless frequency in fluids a and b - _s dimensionless frequency (based on _s ) - angular frequency - ₀ resonant frequency in absence of fluid and internal damping - _r resonant frequency in absence of internal fluid - _ra , _rb resonant frequencies in fluids a and b - dimensionless frequency - dimensionless frequency when _a vanishes - dimensionless frequencies when _a vanishes in fluids a and b - dimensionless resonant frequency when _a , _b, _b and ₀ vanish - dimensionless resonant frequency when _a , _b and _b vanish - dimensionless resonant frequency when _b and _b vanish - dimensionless frequencies at which amplitude is half that at resonance     

A rotating hot-wire technique for spatial sampling of disturbed and manipulated duct flows

The documentation and control of flow disturbances downstream of various open inlet contractions was the primary focus with which to evaluate a spatial sampling technique. An X-wire probe was rotated about the center of a cylindrical test section at a radius equal to one-half that of the test section. This provided quasi-instantaneous multi-point measurements of the streamwise and azimuthal components of the velocity to investigate the temporal and spatial characteristics of the flowfield downstream of various contractions. The extent to which a particular contraction is effective in controlling ingested flow disturbances was investigated by artificially introducing disturbances upstream of the contractions. Spatial as well as temporal mappings of various quantities are presented for the streamwise and azimuthal components of the velocity. It was found that the control of upstream disturbances is highly dependent on the inlet contraction; for example, reduction of blade passing frequency noise in the ground testing of jet engines should be achieved with the proper choice of inlet configurations.List of symbols K _uv correlation coefficient= - P percentage of time that an azimuthal fluctuating velocity derivative dv/d is found - U streamwise velocity component U=U (, t) - V azimuthal or tangential velocity component due to flow and probe rotation V=V (, t) - mean value of streamwise velocity component - U _m resultant velocity from and - mean value of azimuthal velocity component induced by rotation - u fluctuating streamwise component of velocity u=u(, t) - v fluctuating azimuthal component of velocity v = v (, t) - u phase-averaged fluctuating streamwise component of velocity u=u(0) - v phase-averaged fluctuating azimuthal component of velocity v=v() - û average of phase-averaged fluctuating streamwise component of velocity (u()) over cases I-1, II-1 and III-1 û = û() - average of phase-averaged fluctuating azimuthal component of velocity (v()) over cases I-1, II-1 and III-1 - u fluctuating streamwise component of velocity corrected for non-uniformity of probe rotation and/or phase-related vibration u = u(0, t) - v fluctuating azimuthal component of velocity corrected for non-uniformity or probe rotation and/or phase-related vibration v=v (, t) - u ² rms value of corrected fluctuating streamwise component of velocity - rms value of corrected fluctuating azimuthal component of velocity - phase or azimuthal position of X-probe     

Mixed convection on vertical plate for fluids of any prandtl number

A mixed convection parameter=(Ra) ^1/4/(Re)^1/2, with=Pr/(1+Pr) and=Pr/(1 +Pr)^1/2, is proposed to replace the conventional Richardson number, Gr/Re², for combined forced and free convection flow on an isothermal vertical plate. This parameter can readily be reduced to the controlling parameters for the relative importance of the forced and the free convection,Ra ^1/4/(Re ^1/2 Pr ^1/3) forPr 1, and (RaPr)^1/2/(RePr ^1/2 forPr 1. Furthermore, new coordinates and dependent variables are properly defined in terms of, so that the transformed nonsimilar boundary-layer equations give numerical solutions that are uniformly valid over the entire range of mixed convection intensity from forced convection limit to free convection limit for fluids of any Prandtl number from 0.001 to 10,000. The effects of mixed convection intensity and the Prandtl number on the velocity profiles, the temperature profiles, the wall friction, and the heat transfer rate are illustrated for both cases of buoyancy assisting and opposing flow conditions.

---

Mischkonvektion an einer vertikalen Platte für Fluide beliebiger Prandtl-Zahl

Zusammenfassung Für die kombinierte Zwangs- und freie Konvektion an einer isothermen senkrechten Platte wird ein Mischkonvektions-Parameter=( Ra) ^1/4 (Re)^1/2, mit=Pr/(1 +Pr) und=Pr/(1 +Pr)^1/2 vorgeschlagen, den die gebräuchliche Richardson-Zahl, Gr/Re², ersetzen soll. Dieser Parameter kann ohne weiteres auf die maßgebenden Kennzahlen für den relativen Einfluß der erzwungenen und der freien Konvektion reduziert werden,Ra ^1/4/(Re ^1/2 Pr ^1/3) fürPr 1 und (RaPr)^1/4/(RePr)^1/2 fürPr 1. Weiterhin werden neue Koordinaten und abhängige Variablen als Funktion von definiert, so daß für die transformierten Grenzschichtgleichungen numerische Lösungen erstellt werden können, die über den gesamten Bereich der Mischkonvektion, von der freien Konvektion bis zur Zwangskonvektion, für Fluide jeglicher Prandtl-Zahl von 0.001 bis 10.000 gleichmäßig gültig sind. Der Einfluß der Intensität der Mischkonvektion und der Prandtl-Zahl auf die Geschwindigkeitsprofile, die Temperaturprofile, die Wandreibung und den Wärmeübergangskoeffizienten werden für die beiden Fälle der Strömung in und entgegengesetzt zur Schwerkraftrichtung dargestellt.

---

Nomenclature C _f local friction coefficient - C _p specific heat capacity - f reduced stream function - g gravitational acceleration - Gr local Grashoff number,g T _w –T )x³/v² - Nu local Nusselt number - Pr Prandtl number,v/ - Ra local Rayleigh number,g T _w –T x ³/( v) - Re local Reynolds number,u x/v - Ri Richardson number,Gr/Re ² - T fluid temperature - T _w wall temperature - T free stream temperature - u velocity component in thex direction - u free stream velocity - v velocity component in they direction - x vertical coordinate measuring from the leading edge - y horizontal coordinate Greek symbols thermal diffusivity - thermal expansion coefficient - mixed convection parameter (Ra)1/4/Re)^1/2 - pseudo-similarity variable,(y/x) - ₀ conventional similarity variable,(y/x)Re ^1/2 - dimensionless temperature, (T–T T _W –T - unified mixed-flow parameter, [(Re) ^1/2 + (Ra)^1/4] - dynamic viscosity - kinematic viscosity - stretched streamwise coordinate or mixed convection parameter, [1 + (Re)^1/2/(Ra) ^1/4]^–1=/(1 +) - density - Pr/(1 + Pr) _w wall shear stress - stream function - Pr/(l+Pr)^1/3 This research was supported by a grand from the National Science Council of ROC     

A three-parameter model describing the experimental relation between shear stress and shear rate for laminar flow of aqueous polymer solutions

Summary A three-parameter model is introduced to describe the shear rate — shear stress relation for dilute aqueous solutions of polyacrylamide (Separan AP-30) or polyethylenoxide (Polyox WSR-301) in the concentration range 50 wppm – 10,000 wppm. Solutions of both polymers show for a similar rheological behaviour. This behaviour can be described by an equation having three parameters i.e. zero-shear viscosity ₀, infinite-shear viscosity , and yield stress ₀, each depending on the polymer concentration. A good agreement is found between the values calculated with this three-parameter model and the experimental results obtained with a cone-and-plate rheogoniometer and those determined with a capillary-tube rheometer.

---

Zusammenfassung Der Zusammenhang zwischen Schubspannung und Schergeschwindigkeit von strukturviskosen Flüssigkeiten wird durch ein Modell mit drei Parametern beschrieben. Mit verdünnten wäßrigen Polyacrylamid-(Separan AP-30) sowie Polyäthylenoxidlösungen (Polyox WSR-301) wird das Modell experimentell geprüft. Beide Polymerlösungen zeigen im untersuchten Schergeschwindigkeitsbereich von ein ähnliches rheologisches Verhalten. Dieses Verhalten kann mit drei konzentrationsabhängigen Größen, nämlich einer Null-Viskosität ₀, einer Grenz-Viskosität und einer Fließgrenze ₀ beschrieben werden. Die Ergebnisse von Experimenten mit einem Kegel-Platte-Rheogoniometer sowie einem Kapillarviskosimeter sind in guter Übereinstimmung mit den Werten, die mit dem Drei-Parameter-Modell berechnet worden sind.

---

a Pa^–1 physical quantity defined by:a = {1 – ( / ₀)}/ ₀ - c l concentration (wppm) - D m capillary diameter - L m length of capillary tube - P Pa pressure drop - R m radius of capillary tube - u m s^–1 average velocity - v _r m s^–1 local axial velocity at a distancer from the axis of the tube - shear rate (–dv _r /dr) - local shear rate in capillary flow - s^–1 wall shear rate in capillary flow - Pa s dynamic viscosity - _a Pa s apparent viscosity defined by eq. [2] - ( _a ) Pa s apparent viscosity in capillary tube at a distanceR from the axis - ₀ Pa s zero-shear viscosity defined by eq. [4] - Pa s infinite-shear viscosity defined by eq. [5] - l ratior/R - kg m^– density - Pa shear stress - ₀ Pa yield stress - _r Pa local shear stress in capillary flow - _R Pa wall shear stress in capillary flow _R = (PR/2L) - _v m³ s^–1 volume rate of flow With 8 figures and 1 table     

A noninvasive method for the measurement of flow-induced surface displacement of a compliant surface

A noninvasive optical method is described which allows the measurement of the vertical component of the instantaneous displacement of a surface at one or more points. The method has been used to study the motion of a passive compliant layer responding to the random forcing of a fully developed turbulent boundary layer. However, in principle, the measurement technique described here can be used equally well with any surface capable of scattering light and to which optical access can be gained. The technique relies on the use of electro-optic position-sensitive detectors; this type of transducer produces changes in current which are linearly proportional to the displacement of a spot of light imaged onto the active area of the detector. The system can resolve displacements as small as 2 m for a point 1.8 mm in diameter; the final output signal of the system is found to be linear for displacements up to 200 m, and the overall frequency response is from DC to greater than 1 kHz. As an example of the use of the system, results detailing measurements obtained at both one and two points simultaneously are presented.List of symbols C _t elastic transverse wave speed = (G/)^1/2 - d ⁺ spot diameter normalized by viscous length scale - G frequency average of G() - G() shear storage modulus - G() shear loss modulus - l. viscous length scale = v/u _* - N total number of sampled data values - r separation vector for 2-point measurements = (, ) - rms root-mean-square value - R momentum thickness Reynolds number = U _t8/v - t time - u (y) mean streamwise component of velocity in boundary layer - u _* friction velocity = (t _w/)^1/2 - U free-stream velocity - x, y, z longitudinal, normal and spanwise directions - y _o undisturbed surface position - vertical component of compliant surface displacement - ₉₉ boundary layer thickness for which u(y) = 0.99 U _t8 - _l viscous sublayer thickness 5 l _* - frequency average of G()/ - boundary layer momentum thicknes = - fluid dynamic viscosity - v fluid kinematic viscosity = / - , longitudinal, spanwise components of separation vector r - fluid density - time delay - _w wall shear stress     

Gas-lubricated spherical radial bearings

An approximate small-parameter solution of the Reynolds equation describing the pressure distribution in a hemispherical (0==0, ₊=/2 gasdynamic beating was proposed by Pan [1], Unfortunately, it is not suitable for spherical bearings with arbitrary included angle and contains essential inexactnesse with relation to the boundary condition at the end of the bearing. In the following the small-parameter method is used to solve approximately the Reynolds equation for a bearing with arbitrary included angle. In the general case the solution is expressed in terms of Lengendre functions with complex index. Formulas for calculating these functions are presented. The solution is represented in elementary functions for sufficiently small or sufficiently large values of the compressibility number.In conclusion the author wishes to thank A. V. Militsin and P. P. Mostovenko for assistance in carrying out the calculations.     

The effect of background particulates on the delayed transition of a heated 9:1 ellipsoid

An experimental study was done to quantify the effects of a variety of background particulates on the delayed laminar-turbulent transition of a thermally stabilized boundary layer in water. A Laser-Doppler Velocimeter system was used to measure the location of boundary layer transition on a 50 mm diameter, 9:1 fineness ratio ellipsoid. The ellipsoid had a 0.15 m RMS surface finish. Boundary layer transition locations were determined for length Reynolds numbers ranging from 3.0 × 10⁶ to 7.5 × 106. The ellipsoid was tested in three different heating conditions in water seeded with particles of four distinct size ranges. For each level of boundary layer heating, measurements of transition were made for clean water and subsequently, water seeded with 12.5 m, 38.9 m, 85.5 m and 123.2 m particles, alternately. The three surface heating conditions tested were no heating, T = 10°C and T = 15°C where T is the difference between the inlet model heating water temperature, T _i, and free stream water temperature, T . The effects of particle concentration were studied for 85.5 m and 123.2 m particulates.The results of the study can be summarized as follows. The 12.5 m and 38.9 m particles has no measurable effect on transition for any of the test conditions. However, transition was significantly affected by the 85.5 m and 123.2 m particles. Above a length Reynolds number of 4 × 10⁶ the boundary layer transition location moved forward on the body due to the effect of the 85.5 m particles for all heating conditions. The largest percentage changes in transition location from clean water, were observed for 85.5 m particles seeded water.Transition measurements made with varied concentrations of background particulates indicated that the effect of the 85.5 m particles on the transition of the model reached a plateau between 2.65 particulates/ml concentration and 4.2 particles/ml. Measurements made with 123.3 m particles at concentrations up to 0.3 part/ml indicated no similar plateau.     

Instability of a plane axisymmetric flow with a shear discontinuity in the velocity profile

It is proposed to investigate the stability of a plane axisymmetric flow with an angular velocity profile (r) such that the angular velocity is constant when r < r_O – L and r > r_O + L but varies monotonically from ₁ to ₂ near the point r_O, the thickness of the transition zone being small L r_O, whereas the change in velocity is not small ¦₂ – ₁¦ ₂, ₁. Obviously, as L O short-wave disturbances with respect to the azimuthal coordinate (k=m/r_O 1/r_O) will be unstable with a growth rate-close to the Kelvin—Helmholtz growth rate. In the case L=O (i.e., for a profile with a shear-discontinuity) we find the instability growth rate _O and show that where the thickness of the discontinuity L is finite (but small) the growth rate does not differ from _O up to terms proportional to kL 1 and 1/m 1. Using this example it is possible to investigate the effect of rotation on the flow stability. It is important to note that stabilization (or destabilization) of the flow in question by rotation occurs only for three-dimensional or axisymmetric perturbations.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 1, pp. 111–114, January–February, 1985.     

A Strongly Degenerate Quasilinear Equation: the Parabolic Case

We prove the existence and uniqueness of entropy solutions of the Neumann problem for the quasilinear parabolic equation u_t=÷ a(u, Du), where a(z,)=f(z,), and f is a convex function of with linear growth as ||||, satisfying other additional assumptions. In particular, this class includes the case where f(z,)=(z)(), >0, and is a convex function with linear growth as ||||.     

Free convection heat transfer from an isothermal plate with arbitrary inclination

This paper presents a new formulation for the laminar free convection from an arbitrarily inclined isothermal plate to fluids of any Prandtl number between 0.001 and infinity. A novel inclination parameter is proposed such that all cases of the horizontal, inclined and vertical plates can be described by a single set of transformed equations. Moreover, the self-similar equations for the limiting cases of the horizontal and vertical plates are recovered from the transformed equations by setting=0 and=1, respectively. Heated upward-facing plates with positive and negative inclination angles are investigated. A very accurate correlation equation of the local Nusselt number is developed for arbitrary inclination angle and for 0.001 Pr .

---

Wärmeübertragung bei freier Konvektion an einer isothermen Platte mit beliebiger Neigung

Zusammenfasssung Diese Untersuchung stellt eine neue Formulierung der laminaren freien Konvektion von Flüssigkeiten mit einer Prandtl-Zahl zwischen 0,001 und unendlich an einer beliebig schräggestellten isothermen Platte dar. Ein neuer Neigungsparameter wird eingeführt, so daß alle Fälle der horizontalen, geneigten oder vertikalen Platte von einem einzigen Satz transformierter Gleichungen beschrieben werden können. Die unabhängigen Gleichungen für die beiden Fälle der horizontalen and vertikalen Platte wurden für=0 und=1 aus den transformierten Gleichungen wieder abgeleitet. Es wurden erwärmte aufwärtsgerichtete Platten mit positiven und negativen Neigungswinkeln untersucht. Eine sehr genaue Gleichung wurde für die lokale Nusselt-Zahl bei beliebigen Neigungswinkeln und für 0,001 Pr entwickelt.

---

Nomenclature C _p specific heat - f reduced stream function - g gravitational acceleration - Gr local Grashof number,g(T _w –T _w ) x³/v² - h local heat transfer coefficient - k thermal conductivity - n constant exponent - Nu local Nusselt number,hx/k - p pressure - Pr Prandtl number, v/ - Ra local Rayleigh number,g(T _w –T )J x³/v - T fluid temperature - T _w wall temperature - T temperature of ambient fluid - u velocity component in x-direction - v velocity component in y-direction - x coordinate parallel to the plate - y coordinate normal to the plate Greek symbols thermal diffusivity - thermal expansion coefficient - (Ra¦sin¦)^1/4/( Ra cos()^1/5 - pseudo-similarity variable, (y/) - dimensionless temperature, (T–T )/(T _w–T ) - ( Ra cos)^1/5+(Rasin)^1/4 - v kinematic viscosity - 1/[1 +(Ra cos)^1/5/( Ra¦sin)^1/4] - density of fluid - Pr/(1+Pr) - _w wall shear stress - angle of plate inclination measured from the horizontal - stream function - dimensionless dynamic pressure     

Transient laminar free convection in horizontal cylinders

A numerical study of laminar natural convection inside uniformly heated, partially or fully filled horizontal cylinders is made. A coordinate transformation which simplifies the discretization of the equations of motion and energy is utilized. The resulting system of partial differential equations with their boundary conditions is solved using central differences for various Prandtl and Grashof numbers for two different grid sizes. The flow in completely filled cylinders for which experimental data are available is predicted. Close agreement between steady-state predictions and experiments is obtained for temperature and velocity profiles as well as for the streamline contours and isotherms. The technique is further demonstrated by solving the transient natural convection flow inside a partially filled horizontal cylinder with an adiabatic free surface and subjected to uniform wall heating.

---

Laminare freie Konvektion in horizontalen Zylindern

Zusammenfassung Es wurde eine numerische Berechnung der laminaren, freien Konvektion in gleichmäßig beheizten, teilweise oder ganz gefüllten, horizontalen Zylindern durchgeführt. Dabei wird eine Koordinatentransformation benützt, welche die Diskretisierung der Bewegungs- und der Energiegleichung vereinfacht. Das so resultierende System von partiellen Differentialgleichungen wird, zusammen mit seinen Randbedingungen, unter Verwendung einer Differenzenmethode für verschiedene Prandtl und Grashof-Zahlen sowie für zwei verschiedene Gittergrößen gelöst. Für den vollständig gefüllten Zylinder, für den experimentelle Daten verfügbar sind, wird die Strömung vorhergesagt. Dabei wird für stationäre Zustände gute Übereinstimmung zwischen Rechnung und Experiment erzielt. Dies gilt sowohl für den Verlauf der Stromlinien als auch für den der Isothermen. Das Verfahren wird weiterhin am Beispiel der Berechnung instationärer, freier Konvektion in einem partiell gefüllten, horizontalen Zylinder demonstriert, wobei eine adiabate, freie Oberfläche und gleichmäßige Beheizung der Wand angenommen sind.

---

Nomenclature g acceleration due to gravity, m/s² - Gr _R ^* modified Grashof number =gqR⁴/kv² - Gr _R Grashof number =gTR³/v² - H heat function vector, dimensionless - k thermal conductivity, W/mK - L(Y) cord length associated with coordinateY, dimensionless - Pr Prandtl number=v/ - q wall heat flux, W/m² - R radius, m - r(X, Y,Z) distance of a boundary point from the reference axis, dimensionless - S vector derived from the flow field solution, dimensionless - T temperature, K - T _w wall temperature, K - T reference temperature, K - t time, s - u, v velocity components inx, y directions, m/s - U, V dimensionless velocity components inX- and Y-direction normalized withU - U reference velocity=gqR²/k or gTR, m/s - V velocity vector, dimensionless - W vorticity vector, dimensionless - W vorticity, dimensionless - x, y, z cartesian coordinates, m - X, Y, Z cartesian coordinates normalized with a reference length, dimensionless Greek letters thermal diffusivity, m²/s - coefficient of thermal expansion, K^–1 - ,,, non-dimensional coordinates in the transformed domain - non-dimensional temperature =(T–T)_k/q^R or T–T/T_w–T - v kinematic viscosity, m²/s - non-dimensional time=v/R² Gr_Rt or v/R² G _R ^* t - angle measured from the bottom of the cylinder, rads - ^* angle measured from the axis on (– ) plane, rads - heat potential, dimensionless - angle of incidence of the heat flux vector, rads - non-dimensional stream function - vector potential, dimensionless - grid size, dimensionless - ² Laplacian operator - gradient vector     

A note on three-dimensional boundary layer growth

Summary This note is an extension of the work of Görtler²) on two-dimensional boundary layer growth to the three-dimensional case. The solutions of three-dimensional boundary layer equations are obtained by considering the potential flow of the body to be governed by the functions At U ₀(, ) and At U ₀(, ) where is any positive number.     

Modeling pressure-strain rate correlations in turbulence theory

On the basis of a spectral representation of the rapid part _ij,2 of the correlation tensor p(u _i /x _j ) using Cramer's theorem the inequality _ij,2(U _j /x _i )0 is obtained. As distinct from the realizability conditions, it can serve as a direct and very rigorous test of the adequacy of model expressions for _ij,2. In particular, it is shown that the best known of such expressions do not satisfy this test.Translated from Izvestiya Rossiiskoi Akademii Nauk, Mekhanika Zhidkosti i Gaza, No.2, pp. 42–46, March–April, 1992.     

Two-phase flow in heterogeneous porous media III: Laboratory experiments for flow parallel to a stratified system

Two-phase flow in stratified porous media is a problem of central importance in the study of oil recovery processes. In general, these flows are parallel to the stratifications, and it is this type of flow that we have investigated experimentally and theoretically in this study. The experiments were performed with a two-layer model of a stratified porous medium. The individual strata were composed of Aerolith-10, an artificial: sintered porous medium, and Berea sandstone, a natural porous medium reputed to be relatively homogeneous. Waterflooding experiments were performed in which the saturation field was measured by gamma-ray absorption. Data were obtained at 150 points distributed evenly over a flow domain of 0.1 × 0.6 m. The slabs of Aerolith-10 and Berea sandstone were of equal thickness, i.e. 5 centimeters thick. An intensive experimental study was carried out in order to accurately characterize the individual strata; however, this effort was hampered by both local heterogeneities and large-scale heterogeneities.The theoretical analysis of the waterflooding experiments was based on the method of large-scale averaging and the large-scale closure problem. The latter provides a precise method of discussing the crossflow phenomena, and it illustrates exactly how the crossflow influences the theoretical prediction of the large-scale permeability tensor. The theoretical analysis was restricted to the quasi-static theory of Quintard and Whitaker (1988), however, the dynamic effects described in Part I (Quintard and Whitaker 1990a) are discussed in terms of their influence on the crossflow.Roman Letters A interfacial area between the -region and the -region contained within V, m² - a vector that maps onto , m - b vector that maps onto , m - b vector that maps onto , m - B second order tensor that maps onto , m² - C second order tensor that maps onto , m² - E energy of the gamma emitter, keV - f fractional flow of the -phase - g gravitational vector, m/s² - h characteristic length of the large-scale averaging volume, m - H height of the stratified porous medium , m - i unit base vector in the x-direction - K local volume-averaged single-phase permeability, m² - K - {K}, large-scale spatial deviation permeability - { K} large-scale volume-averaged single-phase permeability, m² - K ^* large-scale single-phase permeability, m² - K ^** equivalent large-scale single-phase permeability, m² - K local volume-averaged -phase permeability in the -region, m² - K local volume-averaged -phase permeability in the -region, m² - K - {K } , large-scale spatial deviation for the -phase permeability, m² - K ^* large-scale permeability for the -phase, m² - l thickness of the porous medium, m - l characteristic length for the -region, m - l characteristic length for the -region, m - L length of the experimental porous medium, m - characteristic length for large-scale averaged quantities, m - n outward unit normal vector for the -region - n outward unit normal vector for the -region - n unit normal vector pointing from the -region toward the -region (n = - n ) - N number of photons - p pressure in the -phase, N/m² - p ₀ reference pressure in the -phase, N/m² - local volume-averaged intrinsic phase average pressure in the -phase, N/m² - large-scale volume-averaged pressure of the -phase, N/m² - large-scale intrinsic phase average pressure in the capillary region of the -phase, N/m² - - , large-scale spatial deviation for the -phase pressure, N/m² - p_c , capillary pressure, N/m² - p _c capillary pressure in the -region, N/m² - p capillary pressure in the -region, N/m² - {p _c } ^c large-scale capillary pressure, N/m² - q -phase velocity at the entrance of the porous medium, m/s - q -phase velocity at the entrance of the porous medium, m/s - S_wi irreducible water saturation - S /, local volume-averaged saturation for the -phase - S _i initial saturation for the -phase - S _r residual saturation for the -phase - S ^* { }^*/}^*, large-scale average saturation for the -phase - S saturation for the -phase in the -region - S saturation for the -phase in the -region - t time, s - v -phase velocity vector, m/s - v local volume-averaged phase average velocity for the -phase, m/s - {v } large-scale averaged velocity for the -phase, m/s - v local volume-averaged phase average velocity for the -phase in the -region, m/s - v local volume-averaged phase average velocity for the -phase in the -region, m/s - v -{v } , large-scale spatial deviation for the -phase velocity, m/s - v -{v } , large-scale spatial deviation for the -phase velocity in the -region, m/s - v -{v } , large-scale spatial deviation for the -phase velocity in the -region, m/s - V large-scale averaging volume, m³ - y position vector relative to the centroid of the large-scale averaging volume, m - {y}^c large-scale average of y over the capillary region, m Greek Letters local porosity - local porosity in the -region - local porosity in the -region - local volume fraction for the -phase - local volume fraction for the -phase in the -region - local volume fraction for the -phase in the -region - {}^* { }^*+{ }^*, large-scale spatial average volume fraction - { }^* large-scale spatial average volume fraction for the -phase - mass density of the -phase, kg/m³ - mass density of the -phase, kg/m³ - viscosity of the -phase, N s/m² - viscosity of the -phase, Ns/m² - V /V , volume fraction of the -region ( + =1) - V /V , volume fraction of the -region ( + =1) - attenuation coefficient to gamma-rays, m^-1 - -      

Deformation to breaking of deep water gravity waves

The results of laboratory observations of the deformation of deep water gravity waves leading to wave breaking are reported. The specially developed visualization technique which was used is described. A preliminary analysis of the results has led to similar conclusions than recently developed theories. As a main fact, the observed wave breaking appears as the result of, first, a modulational instability which causes the local wave steepness to approach a maximum and, second, a rapidly growing instability leading directly to the breaking.List of symbols L total wave length - H total wave height - crest elevation above still water level - trough depression below still water level - wave steepness =H/L - crest steepness =/L - trough steepness =/L - F ₁ forward horizontal length from zero-upcross point (A) to wave crest - F ₂ backward horizontal length from wave crest to zero-downcross point (B) - crest front steepness =/F ₁ - crest rear steepness =/F ₂ - vertical asymmetry factor=F ₂/F ₁ (describing the wave asymmetry with respect to a vertical axis through the wave crest) - µ horizontal asymmetry factor=/H (describing the wave asymmetry with respect to a horizontal axis: SWL) - T ₀ wavemaker period - L ₀ theoretical wave length of a small amplitude sinusoïdal wave generated at T _inf0 ^sup–1 frequency - ₀ average wave height     

Über den Einfluß von Querkrümmung und Dichte bei inhomogenen turbulenten Freistrahlen

Zusammenfassung Zur Berechnung turbulenter Strömungen wird das k--Modell im Ansatz für die turbulente Scheinzähigkeit erweitert, so daß es den Querkrümmungs- und Dichteeinfluß auf den turbulenten Transportaustausch erfaßt. Die dabei zu bestimmenden Konstanten werden derart festgelegt, daß die bestmögliche Übereinstimmung zwischen Berechnung und Messung erzielt wird. Die numerische Integration der Grenzschichtgleichungen erfolgt unter Verwendung einer Transformation mit dem Differenzenverfahren vom Hermiteschen Typ. Das erweiterte Modell wird auf rotationssymmetrische Freistrahlen veränderlicher Dichte angewendet und zeigt Übereinstimmung zwischen Rechnung und Experiment.

---

On the influence of transvers-curvature and density in inhomogeneous turbulent free jets

The prediction of turbulent flows based on the k- model is extended to include the influence of transverse-curvature and density on the turbulent transport mechanisms. The empirical constants involved are adjusted such that the best agreement between predictions and experimental results is obtained. Using a transformation the boundary layer equations are solved numerically by means of a finite difference method of Hermitian type. The extended model is applied to predict the axisymmetric jet with variable density. The results of the calculations are in agreement with measurements.

---

Bezeichnungen Wirbelabsorptionskoeffizient - c_i Massenkonzentration der Komponente i - c_D, c_L, c, c₁, c₂ Konstanten des Turbulenzmodells - d Düsendurchmesser - E bezogene Dissipationsrate - f bezogene Stromfunktion - f Korrekturfunktion für die turbulente Scheinzähigkeit - j turbulenter Diffusionsstrom - k Turbulenzenergie - k_i Schrittweite in -Richtung - K dimensionslose Turbulenzenergie - L turbulentes Längenmaß - M_i Molmasse der Komponente i - p Druck - allgemeine Gaskonstante - r Querkoordinate - r_0,5 Halbwertsbreite der Geschwindigkeit - r_0,5c Halbwertsbreite der Konzentration - T Temperatur - u Geschwindigkeitskomponente in x-Richtung - v Geschwindigkeitskomponente in r-Richtung - x Längskoordinate - y allgemeine Funktion - Y_i diskreter Wert der Funktion y - Relaxationsfaktor für Iteration - turbulente Dissipationsrate - transformierte r-Koordinate - kinematische Zähigkeit - Exponent - transformierte x-Koordinate - Dichte - _k, Konstanten des Turbulenzmodells - Schubspannung - allgemeine Variable - Stromfunktion - Turbulente Transportgröße Indizes 0 Strahlanfang - m auf der Achse - r mit Berücksichtigung der Krümmung - t turbulent - mit Berücksichtigung der Dichte - im Unendlichen - Schwankungswert oder Ableitung einer Funktion - – Mittelwert Herrn Professor Dr.-Ing. R. Günther zum 70. Geburtstag gewidmet