Electrochemical behavior and determination of epinephrine at a mercaptoacetic acid self-assembled gold electrode

The electrochemical behavior of epinephrine (EP) at a mercaptoacetic acid (MAA) self-assembled monolayer modified gold electrode was studied. The MAA/Au electrode is demonstrated to promote the electrochemical response of epinephrine by cyclic voltammetry. The possible reaction mechanism is also discussed. The diffusion coefficient D of EP is 6.85 × 10⁻⁶ cm² s⁻¹. In 0.1 mol L⁻¹ phosphate buffer (pH 7.20), a sensitive oxidation peak was observed at 0.177 V, and the peak current is proportional to the concentration of EP in the range of 1.0 × 10⁻⁵–2.0 × 10⁻⁴ mol L⁻¹ and 1.0 × 10⁻⁷–1.0 × 10⁻⁶ mol L⁻¹. The detection limit is 5 × 10⁻⁸ mol L⁻¹. The modified electrode is highly stable and can be applied to the determination of EP in practical injection samples. The method is simple, quick, sensitive and accurate.     

Ultrasensitive Assay of Rhein in Medicine Based on its Enhanced Luminol-K3Fe(CN)6 Chemiluminescence Reaction Using the Flow Injection Technique

Determination of the effective components in traditional Chinese medicine is one of the key steps for its identification. In this paper a novel and sensitive chemiluminescence (CL) method for the determination of rhein coupled with flow-injection analysis (FIA) is developed. It is based on the strong sensitizing effect on the weak CL reaction between luminol and ferricyanide in alkaline solution. Under optimal experimental conditions, the relative CL intensity is proportional to the concentration of rhein in the range of 7.0 × 10⁻¹²–7.0 × 10⁻¹⁰ mol L⁻¹ and 1.0 × 10⁻⁹–4.0 × 10⁻⁵ mol L⁻¹, the detection limit is 1.478 × 10⁻¹³ mol L⁻¹, and the relative standard deviation (RSD) for 9 parallel measurements of 1.408 × 10⁻⁷ mol L⁻¹ rhein is 3.4%. The method was successfully applied to the determination of rhein in pharmaceutical preparations. The possible mechanism of CL is also briefly discussed.     

Trace determination of clenbuterol with an MWCNT-Nafion nanocomposite modified electrode

A method for the determination of trace clenbuterol is described. Multi-walled carbon nanotubes (MWCNTs)-Nafion composite was used to modify the glassy carbon electrode (GCE). The modified electrode showed high sensitivity and good selectivity for clenbuterol detection. It offered a linear range of 1.0 × 10⁻⁹–1.0 × 10⁻⁶ mol · L⁻¹ with a detection limit of 5.0 × 10⁻¹⁰ mol · L⁻¹ in pH = 1.2 solution. The oxidation mechanism of clenbuterol on the electrode was also investigated. Correspondence: Xiao-Ya Hu, Department of Chemistry, Yang Zhou University, Yang Zhou, Jiang Su, P.R. China     

Voltammetric Analysis of the Novel Atypical Antipsychotic Drug Quetiapine in Human Serum and Urine

The electrooxidative behaviour and determination of quetiapine (QTP), a dibenzothiazepine derivative and antipsychotic agent, on a glassy carbon disc electrode was investigated using cyclic (CV), linear sweep (LSV), differential pulse (DPV) and Osteryoung square wave voltammetry (OSWV). Fully validated DP and SW voltammetric procedures are described for the determination of QTP. QTP in pH 3.5 acetate buffer solution presents a well-defined anodic response, studied by the proposed methods. This main response was due to the irreversible, diffusion-controlled, one-electron and one-proton oxidation of the aliphatic nitrogen of the piperazine ring. Under optimal conditions, a detection limit of 4.0 × 10⁻⁸ mol L⁻¹ for DPV and 1.33 × 10⁻⁷ mol L⁻¹ for OSWV, and a linear calibration graph in the range from 4.0 × 10⁻⁶ to 2.0 × 10⁻⁴ mol L⁻¹ were obtained for both methods. The procedure was successfully applied to the determination of the drug in tablets, human serum and human urine with good recoveries. The detection limits were 6.20 × 10⁻⁷ mol L⁻¹ and 5.92 × 10⁻⁷ mol L⁻¹ in human serum and 1.44 × 10⁻⁷ mol L⁻¹ and 1.31 × 10⁻⁶ mol L⁻¹ in human urine, for the DPV and OSWV method, respectively.     

Covalent Modification of Glassy Carbon Electrode with L-Cysteine for the Determination of Acetaminophen

A novel L-cysteine film modified electrode has been fabricated by means of an electrochemical oxidation procedure, and it was successfully applied to the electrochemical determination of acetaminophen. This method utilizes the electrooxidation of amines to their analogous cation radicals to form a chemically stable covalent linkage between the nitrogen atom of the amine and edge plane sites at the glassy carbon electrode surface. The electrochemical behaviour of acetaminophen at the film electrode was investigated in 0.1 mol L⁻¹ phosphate buffer (pH 6.20). It was found that the redox peak current of acetaminophen was enhanced greatly on the film electrode. Linearity between the oxidation peak current and the acetaminophen concentration was obtained in the range of 1.0 × 10⁻⁴–2.0 × 10⁻⁷ mol L⁻¹ with a detection limit of 5.0 × 10⁻⁸ mol L⁻¹. For seven parallel detections of 1.0 × 10⁻⁵ mol L⁻¹ acetaminophen, the relative standard deviation (RSD) was 1.46%, suggesting that the film electrode has excellent reproducibility. Application to the determination of acetaminophen in drug tablets and human urine demonstrated that the film electrode has good stability and high sensitivity.     

Electrochemical behaviors of GMP based on solid-phase extractionon at Cu-Mg-Al hydrotalcite-like compound (HTLC) modified glass carbon electrode

Guanosine-5′-monophosphate (GMP) was investigated the electrochemical behaviors based on solid-phase extractionon (SPE) at Cu-Mg-Al hydrotalcite-like compound (HTLC) modified glass carbon electrode. Cu-Mg-Al hydrotalcite-like compound (HTLC) was proved as a new sorbent for SPE of GMP, which showed an irreversible adsorption oxidation process on the HTLC/GCE with the oxidation peak potential located at 1.15 V (vs. SCE) in a pH 5.0 acetate buffer solution. Influencing factors of the electrochemical behavior of GMP on the HLTC/GCE were optimized and kinetic parameters were calculated. Under the optimal conditions, with differential pulse voltammetry (DPV), a linear relationship was obtained between the oxidation peak current and the GMP concentration in the range from 1.0 × 10^− 6 to 8.0 × 10⁻⁴ mol L⁻¹ with the detection limit as 5.0 × 10⁻⁷ mol L⁻¹ (signal-to-noise ratio of 3). The modified electrode surface has very good reproducibility and stability.     

Sensitive voltammetric sensor of dihydromyricetin based on Nafion/SWNT-modified glassy carbon electrode

A novel voltammetric sensor, based on single-walled carbon nanotubes (SWNT) dispersed in Nafion and modified glassy carbon electrode (GCE), was fabricated and used to determine the trace amounts of dihydromyricetin (DMY). The electrochemical behavior of DMY at this sensor was investigated in 0.1 mol L⁻¹ sulfuric acid solutions + 0.1 mol L⁻¹ NaCl by cyclic voltammetry and squarewave voltammetry. Compared with bare GCE, the electrode presented an excellent response of DMY through an adsorption-controlled quasi-reversible process. Under the optimum conditions, the response peak currents were linear relationship with the DMY concentrations in the range of 1.0 × 10⁻⁷–1.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 9 × 10⁻⁸ mol L⁻¹. Based on this voltammetric sensor, a simple and sensitive electroanalytical method for DMY was proposed and applied to quantitative determination of DMY in Ampelopsis grossedentata samples. In addition, the oxidation mechanism was proposed and discussed, which could be a reference for the pharmacological action of DMY in clinical study.     

Adsorption voltammetry of the zirconium-alizarin red S complex at a multi-walled carbon nanotubes modified carbon paste electrode

We used a carbon paste electrode modified with multi-walled carbon nanotubes as a working electrode and studied the electrochemical behavior of zirconium-alizarin red S complex on it. It was found that the modified electrode exhibited a significant catalytic effect toward the reduction of free alizarin red S and the complex. The second derivative linear scan voltammograms of the complex were recorded by a polarographic analyser from 0 to −1000 mV (vs. SCE), and it was found that the complex can be adsorbed on the surface of the modified electrode, yielding a peak at about −470 mV, corresponding to the reduction of alizarin red S in the complex. The linear range was found to be 2.0 × 10⁻¹¹–8.0 × 10⁻⁷ mol L⁻¹, and the detection limit was 1.0 × 10⁻¹¹ mol L⁻¹ (S/N = 3) for 3 min accumulation. The procedure was successfully applied to the determination of trace amounts of zirconium in the ore samples. Correspondence: Pei-Hong Deng, Department of Chemistry and Material Science, Hengyang Normal University, Hengyang Hunan 421008, P.R. China     

Direct electrochemistry and electrocatalysis of nitrite based on nano-alumina-modified electrode

Simple and sensitive electrochemical method for the determination of nitrite, based on a nano-alumina-modified glassy carbon electrode (GCE), is described. Nitrite yields a well-defined oxidation peak whose potential is 0.74 V at the nano-alumina-coated GCE in 0.1 mol L⁻¹ phosphate buffer (pH 5.0). Compared with bare GCE, the nano-alumina-modified GCE has evident catalytic effect towards the oxidation of nitrite, and its peak current can be significantly enhanced. Some of the experimental parameters were optimized for the determination of nitrite. The oxidation peak current was proportional to nitrite concentration in the range of 5.0 × 10⁻⁸–1.1 × 10⁻³ mol L⁻¹, and a detection limit of 1.0 × 10⁻⁸ mol L⁻¹ was obtained. This method has been successfully used to the determination of nitrite in sausage sample. Furthermore, results obtained by the method have been compared with spectrophotometric method.     

Continuous Monitoring of Sulfur Dioxide with a Gas Permeation Denuder-Based System

 This study describes a continuous flow procedure for monitoring atmospheric sulfur dioxide using a planar gas permeation denuder (GPD) and a fiber optic spectrometer. When gaseous samples are directed through a GPD which consists of a gas-permeable membrane of poly(vinylidene) difluoride and two perspex blocks with engraved channels of mirror image, the fraction of sulfur dioxide passing the membrane is absorbed in a flowing stream of 5.0×10⁻⁴ mol L⁻¹ 5,5′-dithiobis(2,2′-dinitrobenzoic acid) (DTNB) in 0.025 mol L⁻¹ phosphate buffer of pH 7.0, and reacts with DTNB to yield a yellow product. This product is monitored spectrophotometrically at 410 nm with a miniature charge-coupled device (CCD) fiber optic spectrometer. The analytical range of sulfur dioxide is easily adjusted via the flow rate of DTNB solution, normally from 200 ppb to 94 ppm (v/v). The procedure is hardly interfered with by coexisting metal and non-metal species, except for hydrogen sulfide in the atmosphere. The error caused by hydrogen sulfide at a sulfur dioxide level (in ppm) of 2% is less than ±10%. With the proposed procedure, the result for a mimetic air sample is very close to that of the ultraviolet fluorescence method. Correspondence: College of Chemistry and Molecular Engineering, Peking University, Beijing 100871, China. e-mail: yli@chem.pku.edu.cn Received August 12, 2002; accepted November 9, 2002     

Simultaneous Determination of Dopamine and Ascorbic Acid at a Triazole Self-Assembled Monolayer-Modified Gold Electrode

A 3-amino-5-mercapto-1,2,4-triazole (TA) self-assembled monolayer-modified gold electrode (TA SAM/Au) is characterized by X-ray photoelectron spectroscopy, A.C. impedance, cyclic voltammetry, chronoamperometry and chronocoulometry. The TA SAM/Au exhibited good promotion of the electrochemical oxidation of dopamine. Some electrochemical parameters of dopamine such as electron transfer number, exchange current density, standard heterogeneous rate constant, diffusion coefficient, etc., were measured by different electrochemical methods. The peak currents of dopamine were linearly dependent on its concentration in the range of 1.5 × 10⁻⁶–1.0 × 10⁻⁴ mol L⁻¹, with a detection limit of 5.0 × 10⁻⁷ mol L⁻¹. The oxidative peak potentials of dopamine and ascorbic acid were well separated at about 190 ± 10 mV in pH 2.0 BR buffers at TA SAM/Au, the oxidation peak current increases approximately linearly with increasing concentration of both dopamine and ascorbic acid in the concentration range of 9.98 × 10⁻⁶–4.54 × 10⁻⁴ mol L⁻¹. It can be used for simultaneous determination of dopamine and ascorbic acid.     

Electrochemical determination of acetaminophen using a glassy carbon electrode coated with a single-wall carbon nanotube-dicetyl phosphate film

Single-wall carbon nanotubes (SWNT) were dispersed into water in the presence of dicetyl phosphate (DCP), and then a SWNT-DCP film-coated glassy carbon electrode (GCE) was constructed. The electrochemical behavior of acetaminophen at bare GCE and SWNT-DCP modified GCE were compared, suggesting that the SWNT-DCP-modified GCE significantly enhances the oxidation peak current of acetaminophen. A sensitive and simple electrochemical method with a good linear relationship in the range of 1.0 × 10⁻⁷–2.0 × 10⁻⁵ mol L⁻¹, was developed for the determination of acetaminophen. The detection limit is 4.0 × 10⁻⁸ mol L⁻¹ for 3-min accumulation. This method was successfully demonstrated with tablets.     

Development of electrochemical DNA biosensor for Trichoderma harzianum based on ionic liquid/ZnO nanoparticles/chitosan/gold electrode

Electrochemical DNA biosensor was successfully developed by depositing the ionic liquid (e.g., 1-ethyl-3-methylimidazolium trifluoromethanesulfonate ([EMIM][Otf])), ZnO nanoparticles, and chitosan (CHIT) nanocomposite membrane on a modified gold electrode (AuE). The electrochemical properties of the [EMIM][Otf]/ZnO/CHIT/AuE for detection of DNA hybridization were studied. Under optimal conditions using cyclic voltammetry, the target DNA sequences could be detected in the concentration range of 1.0 × 10⁻¹⁸ to 1.82 × 10⁻⁴ mol L⁻¹, and with the detection limit of 1.0 × 10⁻¹⁹ mol L⁻¹. This DNA biosensor detection approaches provide a quick, sensitive, and convenient method to be used in the identification of Trichoderma harzianum.     

Ultra-trace level determination of nitrite in human saliva by spectrofluorimetry using 1,3,5,7-tetramethyl-8-(3,4-diaminophenyl)-difluoroboradiaza-s-indacene

A rapid, highly sensitive and selective fluorogenic method for the determination of traces of nitrite is described. It is based on the reaction of weakly fluorescent 1,3,5,7-tetramethyl-8-(3,4-diaminophenyl)-difluoroboradiaza-s-indacence (DAMBO) and nitrite in acidic aqueous solution to give 1,3,5,7-tetramethyl-8-(5-benzotriazolyl)-difluoroboradiaza-s-indacene (DAMBO-T), which is highly fluorescent. The optimum reaction conditions and other analytical parameters are investigated to enhance the sensitivity of the method. The fluorescence enhancement at 507 nm is linearly related to the concentration of nitrite in the range of 6.0 × 10⁻⁹–5.0 × 10⁻⁷ mol L⁻¹ with a correlation coefficient of R = 0.9995 (n = 10) and a detection limit of 1.0 × 10⁻¹⁰ mol L⁻¹. The R.S.D. is 1.12% (n = 10). The method is applied to the determination of nitrite in human saliva samples with the recoveries of 96. 24–105.30%. Correspondence: Ke-Jing Huang, Department of Chemistry, Wuhan University, Wuhan 430072, P.R. China     

Simple sensor for simultaneous determination of dihydroxybenzene isomers

A simple sensor based on bare carbon ionic liquid electrode was fabricated for simultaneous determination of dihydroxybenzene isomers in 0.1 mol L⁻¹ phosphate buffer solution (pH 6.0). The oxidation peak potential of hydroquinone was about 0.136 V, catechol was about 0.240 V, and resorcinol 0.632 V by differential pulse voltammetric measurements, which indicated that the dihydroxybenzene isomers could be separated absolutely. The sensor showed wide linear behaviors in the range of 5.0 × 10⁻⁷–2.0 × 10⁻⁴ mol L⁻¹ for hydroquinone and catechol, 3.5 × 10⁻⁶–1.535 × 10⁻⁴ mol L⁻¹ for resorcinol, respectively. And the detection limits of the three dihydroxybenzene isomers were 5.0 × 10⁻⁸, 2.0 × 10⁻⁷, 5.0 × 10⁻⁷ mol L⁻¹, respectively (S/N = 3). The proposed method could be applied to the determination of dihydroxybenzene isomers in artificial wastewater and the recovery was from 93.9% to 104.6%.     

Electrochemical Behavior of Uric Acid and Epinephrine at a Meso-2,3-Dimercaptosuccinic Acid Self-Assembled Gold Electrode

A self-assembled electrode with a meso-2,3-dimercaptosuccinic acid (DMSA) monolayer has been characterized by electrochemical quartz crystal microbalance and complex impedance analysis, surface enhanced Raman spectroscopy and cyclic voltammetry. The self-assembled electrode was used for the simultaneous electrochemical detection of epinephrine (EP) and uric acid (UA) in phosphate buffer of pH 7.7. The simultaneous oxidation of EP and UA was performed by cyclic voltammetry (CV) and differential pulse voltammetry (DPV), and the signals for each method were well separated with a potential difference of over 330 mV and without interference by each other. The detection limit of EP is 5.4 × 10⁻⁸ mol L⁻¹ by CV and 5.3 × 10⁻⁸ mol L⁻¹ by DPV and that of UA is 8.4 × 10⁻⁸ mol L⁻¹ by CV and 4.2 × 10⁻⁸ mol L⁻¹ by DPV. The DMSA self-assembled electrode can be applied to the simultaneous determination of EP and UA.     

Ensemble of carbon fiber ultra-microelectrodes modified with nanotubes, and its application to the determination of dopamine

An ensemble of carbon fibers ultra-microelectrode modified with carbon nanotubes (EUME-CNTS) has been constructed based on a thin carbon nanotubes film which was coated onto surfaces of carbon fibers of ultra-microelectrode. SEM micrographs illustrated the image of carbon nanotubes on the carbon fiber surface. The electrochemical characteristics of the EUME-CNTS has been investigated by cyclic voltammetry. The electrochemical properties of dopamine on this electrode were also studied, and the detection limit was found to be 2.0 × 10⁻⁹ mol·L⁻¹. Linear calibration plots were obtained for the oxidation peak current in a range 1.0 × 10⁻⁷–8.0 × 10⁻⁵ mol·L⁻¹. Correspondence: Xiuhua Liu, Kuaizhi Liu, Department of Chemistry and Chemical Engineering, Henan University, Henan Kaifeng 475001, P.R. China     

Determination of thiocyanate ions at nanolevel in real samples using coated graphite electrode based on synthesised macrocyclic Zn(II) complex

The electrode characteristics and selectivities of PVC-based thiocyanate selective polymeric membrane electrode (PME) incorporating the newly synthesized zinc complex of 6,7:14,15-Bzo₂-10,11-(4-methylbenzene)-[15]-6,8,12,14-tetraene-9,12-N₂-1,5-O₂ (I ₁ ) and zinc complex of 6,7:14,15-Bzo₂-10,11-(4-methylbenzene)-[15]-6,14-diene-9,12-dimethylacrylate-9,12-N₂-1,5-O₂ (I ₂ ) are reported here. The best response was observed with the membrane having a composition of I₂:PVC:o-NPOE:HTAB in the ratio of 6:33:59:2 (w/w; milligram). This electrode exhibited Nernstian slope for thiocyanate ions over working concentration range of 4.4 × 10⁻⁷ to 1.0 × 10⁻² mol L⁻¹ with detection limit of 2.2 × 10⁻⁷ mol L⁻¹. The performance of this electrode was compared with coated graphite electrode (CGE), which showed better response characteristics w.r.t Nernstian slope 59.0 ± 0.2 mV decade⁻¹ activity, wide concentration range of 8.9 × 10⁻⁸ to 1.0 × 10⁻² mol L⁻¹ and detection limit of 6.7 × 10⁻⁸ mol L⁻¹. The response time for CGE and PME was found to be 8 and 10 s, respectively. The proposed electrode (CGE) was successfully applied to direct determination of thiocyanate in biological and environmental samples and also as indicator electrode in potentiometric titration of SCN⁻ ion.     

Voltammetric Sensor for the Determination of Parathion Using an Electropolymerized Poly(Carmine) Film Electrode

A voltammetric sensor for the determination of parathion has been developed based on the use of a poly(carmine) film electrode. The reduction of parathion at the poly(carmine) modified glassy carbon electrode (GCE) is studied by cyclic voltammetry (CV) and linear scan voltammetry (LSV). Parathion yields a well-defined reduction peak at a potential of −0.595 V on the poly(carmine) modified GCE in pH 6.0 phosphate buffer solution (PBS). Compared with that on a bare GCE, the reduction peak current of parathion is significantly enhanced. All the experimental parameters are optimized for the determination of parathion. The reduction peak current is linear with the parathion concentration in the range of 5.0 × 10⁻⁸ to 1.0 × 10⁻⁵ mol L⁻¹, and the detection limit is 1.0 × 10⁻⁸ mol L⁻¹.     

Sensitive fluorescent probes for determination of hydrogen peroxide and glucose based on enzyme-immobilized magnetite/silica nanoparticles

Sensitive fluorescent probes for the determination of hydrogen peroxide and glucose were developed by immobilizing enzyme horseradish peroxidase (HRP) on Fe₃O₄/SiO₂ magnetic core–shell nanoparticles in the presence of glutaraldehyde. Besides its excellent catalytic activity, the immobilized enzyme could be easily and completely recovered by a magnetic separation, and the recovered HRP-immobilized Fe₃O₄/SiO₂ nanoparticles were able to be used repeatedly as catalysts without deactivation. The HRP-immobilized nanoparticles were able to activate hydrogen peroxide (H₂O₂), which oxidized non-fluorescent 3-(4-hydroxyphenyl)propionic acid to a fluorescent product with an emission maximum at 409 nm. Under optimized conditions, a linear calibration curve was obtained over the H₂O₂ concentrations ranging from 5.0 × 10⁻⁹ to 1.0 × 10⁻⁵ mol L⁻¹, with a detection limit of 2.1 × 10⁻⁹ mol L⁻¹. By simultaneously using glucose oxidase and HRP-immobilized Fe₃O₄/SiO₂ nanoparticles, a sensitive and selective analytical method for the glucose detection was established. The fluorescence intensity of the product responded well linearly to glucose concentration in the range from 5.0 × 10⁻⁸ to 5.0 × 10⁻⁵ mol L⁻¹ with a detection limit of 1.8 × 10⁻⁸ mol L⁻¹. The proposed method was successfully applied for the determination of glucose in human serum sample.