Mechanical reliability of transparent conducting IZTO film electrodes for flexible panel displays

The mechanical reliability of transparent In-Zn-Sn-O (IZTO) films grown using pulsed DC magnetron sputtering with a single oxide alloyed ceramic target on a transparent polyimide (PI) substrate at room temperature is investigated. All IZTO films deposited at room temperature have an amorphous structure. However, their optical and electrical properties change depending on the oxygen partial pressure applied during depositing process. At an oxygen partial pressure of 3%, the films exhibit a resistivity of 8.3 × 10⁻⁴ Ω cm and an optical transmittance of 86%. Outer bending tests show that the critical bending radius decreases from 10 mm to 7.5 mm when the oxygen partial pressure increases from 1% to 3%. In the inner bending test, the critical bending radius is independent of oxygen partial pressure at 3.5 mm, indicating excellent film flexibility. In the dynamic fatigue test, the electrical resistance of the films reduces by less than 1% for more than 2000 bending cycles. These results suggest that IZTO films have excellent mechanical durability and flexibility in comparison to ITO films.     

Rapid thermal annealing of ITO films

Tin-doped indium oxide (ITO) films with 200 nm thickness were deposited on glass substrates by DC magnetron sputtering at room temperature. And they were annealed by rapid thermal annealing (RTA) method in vacuum ambient at different temperature for 60 s. The effect of annealing temperature on the structural, electrical and optical properties of ITO films was investigated. As the RTA temperature increases, the resistivity of ITO films decreases dramatically, and the transmittance in the visible region increases obviously. The ITO film annealed at 600 °C by RTA in vacuum shows a resistivity of 1.6 × 10⁻⁴ Ω cm and a transmittance of 92%.     

Effect of substrate temperature on the growth of ITO thin films

Indium tin oxide (ITO) thin films were deposited onto glass substrates by rf magnetron sputtering of ITO target and the influence of substrate temperature on the properties of the films were investigated. The structural characteristics showed a dependence on the oxygen partial pressure during sputtering. Oxygen deficient films showed (4 0 0) plane texturing while oxygen-incorporated films were preferentially oriented in the [1 1 1] direction. ITO films with low resistivity of 2.05 × 10⁻³ Ω cm were deposited at relatively low substrate temperature (150 °C) which shows highest figure of merit of 2.84 × 10⁻³ square/Ω⋅     

ITO/Au/ITO multilayer thin films for transparent conducting electrode applications

Transparent and conducting ITO/Au/ITO multilayered films were deposited without intentional substrate heating on polycarbonate (PC) substrate using a magnetron sputtering process. The thickness of ITO, Au and ITO metal films in the multilayered structure was constant at 50, 10 and 40 nm, respectively.Although the substrate temperature was kept constant at 70 °C, ITO/Au/ITO films were polycrystalline with an (1 1 0) X-ray diffraction peak, while single ITO films were amorphous. Surface roughness analysis indicated ITO films had a higher average roughness of 1.76 nm, than the ITO/Au/ITO film roughness of 0.51 nm. The optoelectrical properties of the ITO/Au/ITO films were dependent on the Au thin film, which affected the ITO film crystallinity. ITO/Au/ITO films on PC substrates were developed with a resistivity as low as 5.6 × 10⁻⁵ Ω cm and a high optical transmittance of 71.7%.     

Room temperature deposition of crystalline indium tin oxide films by cesium-assisted magnetron sputtering

Indium tin oxide (ITO) films were deposited on a Si (1 0 0) substrate at room temperature by cesium-assisted magnetron sputtering. Including plasma characteristics, the structural, electrical, and optical properties of deposited films were investigated as a function of cesium partial vapor pressure controlled by cesium reservoir temperature. We calculated the cesium coverage on the target surface showing maximum formation efficiency of negative ions by means of the theoretical model. Cesium addition promotes the formation efficiency of negative ions, which plays important role in enhancing the crystallinity of ITO films. In particular, the plasma density was linearly increased with cesium concentrations. The resultant decrease in specific resistivity and increase in transmittance (82% in the visible region) at optimum cesium concentration (4.24 × 10⁻⁴ Ω cm at 80 °C of reservoir temperature) may be due to enhanced crystallinity of ITO films. Excess cesium incorporation into ITO films resulted in amorphization of its microstructure leading to degradation of ITO crystallinity. We discuss the cesium effects based on the growth mechanism of ITO films and the plasma density.     

Rapid thermal annealing effects on the structural and optical properties of Na–N codoped ZnO films

Polycrystalline ZnO thin films codoped with Na and N were obtained by chemical bath deposition. The structural characteristic and the optical properties of the rapid thermal annealed ZnO:(Na,N) films were investigated by X-ray diffraction, scanning electron microscopy, energy dispersive spectrometer (EDS), Raman spectrum and room-temperature photoluminescence. After RTA treatment, the XRD spectra showed a continuous decrease of the full- width at half-maximum (FWHM) of the (0 0 2) diffraction peak of the ZnO:(Na,N) film. The Raman spectra revealed that the intensity of the mode around 582 cm⁻¹ increased with the increase of the RTA temperature. The PL spectra showed different trends in the UV luminescence of ZnO:(Na,N) films after RTA treatments.     

Nanocomposite oxide thin films grown by pulsed energy beam deposition

Highly non-stoichiometric indium tin oxide (ITO) thin films were grown by pulsed energy beam deposition (pulsed laser deposition-PLD and pulsed electron beam deposition-PED) under low oxygen pressure. The analysis of the structure and electrical transport properties showed that ITO films with a large oxygen deficiency (more than 20%) are nanocomposite films with metallic (In, Sn) clusters embedded in a stoichiometric and crystalline oxide matrix. The presence of the metallic clusters induces specific transport properties, i.e. a metallic conductivity via percolation with a superconducting transition at low temperature (about 6 K) and the melting and freezing of the In-Sn clusters in the room temperature to 450 K range evidenced by large changes in resistivity and a hysteresis cycle. By controlling the oxygen deficiency and temperature during the growth, the transport and optical properties of the nanocomposite oxide films could be tuned from metallic-like to insulating and from transparent to absorbing films.     

High mobility W-doped In2O3 thin films: Effect of growth temperature and oxygen pressure on structural, electrical and optical properties

Highly conducting and transparent thin films of tungsten (W)-doped indium oxide were obtained using pulsed laser deposition to study the effect of growth temperature and oxygen pressure on structural, optical and electrical properties. The transparency of the films is seen to largely depend on the growth temperature. The electrical properties, however, are found to depend strongly on both the growth temperature and the oxygen pressure. High mobility (up to 358 cm² V⁻¹ s⁻¹), low resistivity (1.1 × 10⁻⁴ Ω cm), and relatively high transmittance (∼90%) tungsten-doped indium oxide films have been prepared at a growth temperature of 500 °C and an oxygen pressure of 1 × 10⁻⁶ bar.     

Opto-electrical properties of Ti-doped In2O3 thin films grown by pulsed laser deposition

By ablating titanium containing In₂O₃ target with a KrF excimer laser, highly conducting and transparent films on quartz were obtained to investigate the effects of growth temperature and oxygen pressure on the structural, optical and electrical properties of these films. We find that the transparency of the films depends more on the growth temperature and less on the oxygen pressure. Electrical properties, however, are found to be sensitive to both the growth temperature and oxygen pressure. We report in this paper that a growth temperature of 500 °C and an oxygen pressure of 7.5 × 10⁻⁷ bar lead to titanium-doped indium oxide films which have high mobility (up to 199 cm² V⁻¹ s⁻¹), low resistivity (9.8 × 10⁻⁵ Ω cm), and relatively high transmittance (∼88%).     

Improvement of photoluminescence mechanism of CTA-treated Si-implanted SiO2 films by using RTA

In this paper, a shift in the photoluminescence (PL) peak from blue to near-infrared region was observed in the Si⁺-implanted 400-nm-thick SiO₂ films with the rapid thermal annealing (RTA) method only. As the Si⁺-fluence was 1×10¹⁶ ions/cm², a blue band was observed in the films after RTA at 1050 °C for 5 s in dry-N₂ atmosphere; then, the band shifted from blue to orange upon increasing the holding temperature of RTA to 1250 °C in the films after the isochronal RTA in dry N₂. Furthermore, while the fluence was increased to 3×110¹⁶ ions/cm² and the holding temperature was at the same range between 1050 and 1250 °C, the PL peak occurred between red and near-infrared regions. Although the RTA and conventional thermal annealing (CTA) methods produce a similar mechanism, the CTA method needs a much longer annealing-time and a higher Si⁺-implanted dose than the RTA method for producing the same shift and intensity of PL peak from the as-implanted sample. Therefore, the RTA method can produce the mechanism in the Si⁺-implanted sample with the PL energy between blue and near-infrared band in place of the CTA method.     

Structural, optical and electrical characterization of highly conducting Mo-doped In2O3 thin films

Highly conducting and transparent thin films of molybdenum-doped indium oxide were deposited on quartz by pulsed laser deposition. The effect of growth temperature and oxygen partial pressure on the structural, optical and electrical properties was studied. We find that the film transparency depends on the growth temperature. The average transmittance of the films grown at different temperatures is in range of 48-87%. The X-ray diffraction results show that the films grown at low temperature are amorphous while the films grown at higher temperature are crystalline. Electrical properties are found to be sensitive to both the growth temperature and oxygen pressure. Resistivity of the films decreases from 1.3 × 10⁻³ Ω cm to 8.9 × 10⁻⁵ Ω cm while mobility increases from 9 cm²/V s to 138 cm²/V s as the growth temperature increases from room temperature to 700 °C. However, with increase in oxygen pressure, resistivity increases but the mobility decreases after attaining a maximum. The temperature-dependent resistivity measurements show transition form semiconductor to metallic behavior. The film grown at 500 °C under an oxygen pressure of 1.0 × 10⁻³ mbar is found to exhibit high mobility (250 cm²/V s), low resistivity (6.7 × 10⁻⁵ Ω cm), and relatively high transmittance (∼90%).     

Electrochemical properties of nanostructured lanthanum strontium manganite cathode fabricated by electrostatic spray deposition

Electrostatic spray deposition was applied to prepare nanoporous lanthanum strontium manganite (LSM) films with high specific surface area (37.34 m²/g) for the cathode application in solid oxide fuel cell (SOFC). The electrochemical characteristics were investigated at a temperature range from 546 to 777 °C and oxygen partial pressure from 0.01 to 1.0 atm. The diffusion of atomic oxygen and oxygen ion transfer from three-phase boundary to the YSZ electrolyte were found to be the rate-determining steps for oxygen reduction reaction on LSM cathode. The polarization resistance of the LSM prepared using electrostatic spray deposition decreased from 15 to 1.2 Ωcm² with increasing temperature from 546 to 777 °C and the activation energy was 0.81 eV. It was demonstrated that the ESD method offers a promising approach for the preparation of electrochemically active nanoporous layers, particularly applicable for solid oxide fuel cells.     

Preparation and characterization of indium tin oxide films formed by oxygen ion beam assisted deposition

Indium tin oxide (ITO) films were produced by low-energy oxygen ion beam assisted electron-beam evaporation. The dependence of surface morphology, electrical and optical properties on evaporation rate, oxygen ion beam energy and density, as well as substrate temperatures was characterized by atomic force microscopy, X-ray photoelectron spectroscopy, Hall-effect and optical transmittance measurements. The results show that high-quality ITO films (resistivity of 7.0×10⁻⁴ Ω cm, optical transmittance above 85% at wavelength 550 nm, surface roughness of 0.6 nm in root mean square) can be obtained at room temperature.     

Ellipsometry investigation of the effects of annealing temperature on the optical properties of indium tin oxide thin films studied by Drude-Lorentz model

Float glass substrates covered by high quality ITO thin films (Balzers) were subjected for an hour to single thermal treatments at different temperature between 100 °C and 600 °C. In order to study the electric and optical properties of both annealed and not annealed ITO-covered float glasses, ellipsometry, spectrophotometry, impedance analysis, and X-ray measurements were performed. Moreover, variable angle spectroscopic ellipsometry provides relevant information on the electronic and optical properties of the samples. ITO film is modeled as a dense lower layer and a surface roughness layer. The estimated optical density for ITO and the optical density of the surface roughness ITO layer increases with the annealing temperature. In the near-IR range, the extinction coefficient decreases while the maximum of the absorption in the near UV range shift towards low photon energy as the annealing temperature increases. Spectrophotometry was used to estimate the optical band-gap energy of the samples. The thermal annealing changes strongly the structural and optical properties of ITO thin films, because during the thermal processes, the ITO thin film absorbs oxygen from air. This oxygen absorption decreases the oxygen vacancies therefore the defect densities in the crystalline structure of the ITO thin films also decrease, as confirmed both by ellipsometry and X-ray measurements.     

Growth of transparent conducting nano-structured In doped ZnO thin films by pulsed DC magnetron sputtering

Transparent conducting nano-structured In doped zinc oxide (IZO) thin films are deposited on corning 7059 glass substrates by bipolar pulsed DC magnetron sputtering with variation of pulsed frequency and substrate temperature. Highly c-axis oriented IZO thin films were grown in perpendicular to the substrate on the 30 kHz and 500 °C. The IZO films exhibited surface roughness of 3.6 nm similar to the commercial ITO and n-type semiconducting properties with electrical resistivity (carrier mobility) of about 5 × 10⁻³ Ω cm (14 cm²/V s). The optical characterization showed high transmittance of over 85% in the UV-vis region and exhibited the absorption edge of near 350 nm. In micro-Raman spectra, the origin of two additional modes is attributed to the host lattice defect due to the addition of In dopant. These results suggest that the IZO film can possibly be applied to make transparent conducting electrodes for flat panel displays.     

Influence of heating rate on the crystalline properties of 0.7BiFeO3-0.3PbTiO3 thin films prepared by sol-gel process

0.7BiFeO₃-0.3PbTiO₃ (BFPT7030) thin films were deposited on SiO₂/Si substrates by sol-gel process. The influence of heating rate on the crystalline properties of BFPT7030 thin films were studied by X-ray diffraction (XRD), scanning electron microscope (SEM), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). XRD patterns of the films showed that a pure perovskite phase exists in BFPT7030 films annealed by rapid thermal annealing (RTA) technique. SEM and AFM observations demonstrated that the BFPT7030 films annealed by RTA at 700 °C for 90 s with the heating rate of 1 °C s⁻¹ could show a dense, crack-free surface morphology, and the films’ grains grow better than those of the films annealed by RTA at the same temperature with other heating rates. XPS results of the films indicated that the ratio of Fe³⁺:Fe²⁺ is about 21:10 and 9:5 for the films annealed by RTA at 700 °C for 90 s with the heating rate of 1 and 20 °C s⁻¹, respectively. That means the higher the heating rate, the higher the concentration of Fe²⁺ in the BFPT7030 thin films.     

Effects of annealing temperature and method on structural and optical properties of TiO2 films prepared by RF magnetron sputtering at room temperature

TiO₂ thin film was deposited on non-heated Si(1 0 0) substrate by RF magnetron sputtering. The as-deposited films were annealed by a conventional thermal annealing (CTA) and rapid thermal annealing (RTA) at 700 and 800 °C, and the effects of annealing temperature and method on optical properties of studied films were investigated by measuring the optical band gaps and FT-IR spectra. And we also compared the XRD patterns of the studied samples. The as-deposited film showed a mixed structure of anatase and brookite. Only rutile structures were found in samples annealed above 800 °C by CTA, while there are no special peaks except the weak brookite B(2 3 2) peak for the sample annealed at (or above) 800 °C by RTA. FT-IR spectra show the broad peaks due to Ti-O vibration mode in the range of 590-620 cm⁻¹ for the as-deposited film as well as samples annealed by both annealing methods at 700 °C. The studied samples all had the peaks from Si-O vibration mode, which seemed to be due to the reaction between TiO₂ and Si substrate, and the intensities of these peaks increased with increasing of annealing temperature. The optical band gap of the as-deposited film was 3.29 eV but it varied from 3.39 to 3.43 eV as the annealing temperature increased from 700 to 800 °C in the samples annealed by CTA. However, it varied from 3.38 to 3.32 eV as the annealing temperature increased from 700 to 800 °C by RTA.     

Effect of substrate temperature on the structural, optical and electrical properties of dc magnetron sputtered tantalum oxide films

dc reactive magnetron sputtering technique was employed for deposition of tantalum oxide films on quartz and silicon substrates by sputtering of pure tantalum target in the presence of oxygen and argon gases under various substrate temperatures in the range 303-973 K. The variation of cathode potential with the oxygen partial pressure was systematically studied. The influence of substrate temperature on the chemical binding configuration, crystal structure and optical properties was investigated. X-ray photoelectron spectroscopic studies indicated that the films formed at oxygen partial pressures ≥1 × 10⁻⁴ mbar were stoichiometric. The Fourier transform infrared spectroscopic studies revealed that the films formed up to substrate temperatures <673 K showed a broad absorption band at 750-1000 cm⁻¹ and a sharp band at 630 cm⁻¹ indicated the presence of amorphous phase while at higher substrate temperatures the appearance of bands at about 810 and 510 cm⁻¹ revealed the polycrystalline nature. The effect of substrate temperature on the electrical characteristics of Al/Ta₂O₅/Si structure was investigated. The dielectric constant values were in the range 17-29 in the substrate temperature range of 303-973 K. The current-voltage characteristics showed modified Poole-Frenkel conduction mechanism with a tendency for reduction of the compensation level. The optical band gap of the films decreased from 4.44 to 4.25 eV and the refractive index increased from 1.89 to 2.25 with the increase of substrate temperature from 303 to 973 K.     

Preparation and characterization of n-type conductive (Al, Co) co-doped ZnO thin films deposited by sputtering from aerogel nanopowders

Highly transparent, n-type conducting ZnO thin films were obtained by low temperature magnetron sputtering of (Co, Al) co-doped ZnO nanocrystalline aerogels. The nanoparticles of ∼30 nm size were synthesized by a sol-gel method using supercritical drying in ethyl alcohol. The structural, optical and electrical properties of the films were investigated. The ZnO films were polycrystalline textured, preferentially oriented with the (0 0 2) crystallographic direction normal to the film plane. The films show within the visible wavelength region an optical transmittance of more than 90% and a low electrical resistivity of 3.5 × 10⁻⁴ Ω cm at room temperature.     

Low temperature deposition of transparent conducting ITO/Au/ITO films by reactive magnetron sputtering

Transparent conducting indium tin oxide/Au/indium tin oxide (ITO) multilayered films were deposited on unheated polycarbonate substrates by magnetron sputtering. The thickness of the Au intermediated film varied from 5 to 20 nm. Changes in the microstructure, surface roughness and optoelectrical properties of the ITO/Au/ITO films were investigated with respect to the thickness of the Au intermediated layer. X-ray diffraction measurements of ITO single layer films did not show characteristic diffraction peaks, while ITO/Au/ITO films showed an In₂O₃ (2 2 2) characteristic diffraction peak. The optoelectrical properties of the films were also dependent on the presence and thickness of the Au thin film. The ITO 50 nm/Au 10 nm/ITO 40 nm films had a sheet resistance of 5.6 Ω/□ and an average optical transmittance of 72% in the visible wavelength range of 400-700 nm. Consequently, the crystallinity, which affects the optoelectrical properties of ITO films, can be enhanced with Au intermediated films.