Fabrication,characterization, and performance evaluation of polyethersulfone/TiO2 nanocomposite ultrafiltration membranes for produced water treatment

In the present work, development of neat and nanocomposite polyethersulfone membranes composed of TiO₂ nanoparticles is presented. Membranes are fabricated using nonsolvent phase inversion process with the objective of improving antifouling, hydrophilicity, and mechanical properties for real and synthetic produced water treatment. Membranes are characterized using scanning electron microscopy, Fourier‐transform infrared, contact angle, porosity measurement, compaction factor, nanoparticles stability, and mechanical strength. The performance of prepared membranes was also characterized using flux measurement and oil rejection. Fourier‐transform infrared spectra indicated that noncovalence bond formed between Ti and polyethersulfone chains. The contact angle results confirmed the improved hydrophilicity of nanocomposite membranes upon addition of TiO₂ nanoparticles owing to the strong interactions between fillers and water molecules. The increased water flux for nanocomposite membranes in comparison with neat ones can be due to coupling effects of improved surface hydrophilicity, higher porosity, and formation of macrovoids in the membrane structure. The membrane containing 7 wt% of TiO₂ nanoparticles was the best nanocomposite membrane because of its high oil rejection, water flux, antifouling properties, and mechanical stability. The pure water flux for this membrane was twice greater than that of neat membrane without any loss in oil rejection. The hydrophilicity and antifouling resistance against oil nominates developed nanocomposite membranes for real and synthetic produced water treatment applications with high performance and extended life span.     

Exploring the characteristics,performance, and modification of Matrimid for development of thin‐film composite and thin‐film nanocomposite reverse osmosis membranes

Reverse osmosis (RO) membrane technology is widely employed to address the demands for freshwater. In this study, fabrication and performance evaluation of customized RO membranes comprised of Matrimid and polyacrylonitrile (PAN) is carried out. While exploring adoption of slip coating procedure, the effects of various modification techniques including incorporation of TiO₂ nanoparticles and polyethylene glycol (PEG) into the skin layer as well as cross‐linking were investigated. The individual and combined effects of parameters on membrane morphology, surface characteristics and performance were also examined. Despite the distinctive characteristics of involved materials, delamination‐free composite membranes were successfully formed with an intimate contact at the interface of two layers. The results also indicated that increasing concentration of Matrimid in dope solution led to increase in membrane thickness and consequently decline in water flux. In the best case, membrane prepared using 1 wt.% Matrimid in dope exhibited water flux of 0.98 LMH and NaCl rejection of 95.7%. Also, incorporation of 3 wt.% TiO₂ nanoparticles offered membranes with improved water flux of 1.37 LMH and salt rejection of 95.8%. On the other hand, water flux and salt rejection in membranes containing 5 wt.% PEG were 1.18 LMH and 96.2%, respectively. The co‐presence of both nanoparticles and PEG provided more insights about the contributing factors in tuned membranes. Modification of skin layer by cross‐linking significantly improved salt rejection at the expense of water flux. The results are scientifically interpreted and compared to the values reported in literature.     

Preparation and characterization of TiO2/Pebax/(PSf‐PES) thin film nanocomposite membrane for humic acid removal from water

New thin film composite (TFC) membrane was prepared via coating of Pebax on PSf‐PES blend membrane as support, and its application in wastewater treatment was investigated. To modify this membrane, hydrophilic TiO₂ nanoparticles were coated on its surface at different loadings via dip coating technique. The as‐prepared membrane was characterized using Fourier transform infrared spectroscopy, scanning electron microscopy (SEM), field emission SEM, and contact angle analysis. The Fourier transform infrared spectroscopy analysis and surface SEM images indicated that TiO₂ was successfully coated on the membrane surface. In addition, the results stated that the hydrophilicity and roughness of membrane surface increased by addition of TiO₂ nanoparticles. Performance of TFC and modified TFC membranes was evaluated through humic acid removal from aqueous solution. Maximum permeate flux and humic acid rejection were obtained at 0.03 and 0.01 wt% TiO₂ loadings, respectively. Rejection was enhanced from 96.38% to 98.92% by the increase of feed concentration from 10 to 30 ppm. Additionally, membrane antifouling parameters at different pressures and feed concentration were determined. The results indicated that surface modification of membranes could be an effective method for improvement of membrane antifouling property.     

Improving surface structure of photocatalytic self‐cleaning membrane by WO3/PANI nanoparticles

To create a self‐cleaning feature and improve antifouling property, polysulfone (PSf) membranes were modified with WO₃ and polyaniline (PANI) nanoparticles (0–2 wt%) via phase inversion method for ultrafiltration of landfill leachate. The mass ratio of WO₃ nanoparticles was varied between 0, 40 and 60 wt% in different loadings. All synthesized membranes were tested with and without UV irradiation to evaluate the self‐cleaning feature. The synthesized PANI was analyzed with scanning electron morphology (SEM), atomic force microscopy (AFM) and Fourier transform infrared spectroscopy (FTIR). The surface hydrophilicity of the modified membranes increases with increasing the nanoparticle loadings (0–2 wt%). The membrane morphology indicated higher porosity and more finger like pores for the modified membranes. The porosity of 86.8% was achieved for the membrane containing 2 wt% PANI. The flux recovery ratio (FR) of membranes without UV radiation was increased by increasing the ratio of PANI to WO₃ nanoparticles, while the antifouling ability of membranes including WO₃ nanoparticles improved and reached to 98.87% after UV radiation. The highest COD removal before (76.65 %) and after (78.42%) UV radiation was obtained for the membrane containing 2 wt% nanoparticle loading. Copyright © 2016 John Wiley & Sons, Ltd.     

Chitosan‐modified graphene oxide as a modifier for improving the structure and performance of forward osmosis membranes

Chitosan (CS) with good hydrophilicity and charged property was used to modify graphene oxide (GO), the obtained GO‐CS was used as a novel modifier to fabricate thin film composite forward osmosis (FO) membranes. The results revealed that the amino groups on CS reacted with carboxyl groups on GO, and the lamellar structure of the GO nanosheets was peeled off by CS, resulting in the reducing of their thicknesses. The GO‐CS improved the hydrophilicity of polyethersulfone (PES) substrate, and their contact angles decreased to 64° with the addition of GO‐CS in the substrate. GO‐CS also increased the porosity of the substrate and surface roughness of FO membrane, thereby optimizing the water flux and reverse salt flux of FO membrane. The average water flux of the FO membrane reached the optimal flux of 21.34 L/(m² h) when GO‐CS addition was 0.5 wt%, and further addition of GO‐CS to the substrate would decrease the water flux of FO membrane, and the reverse salt flux also decreased to the lowest value of 2.26 g/(m² h). However, the salt rejection of the membrane increased from 91.4% to 95.1% when GO‐CS addition increased from 0.5 to 1.0 wt% under FO mode using 1 mol/L sodium chloride (NaCl) solution as draw solution (DS). In addition, high osmotic pressure favored water permeation, and at the same concentration of DS, magnesium chloride (MgCl₂) exhibited better properties than NaCl. These results all suggested that GO‐CS was a good modifier to fabricate FO membrane, and MgCl₂ was a good DS candidate.     

Polysulfone/Brij‐58 blend nanofiltration membranes: preparation,morphology and performance

In present research, novel asymmetric polysulfone (PSF) membranes with high hydrophilicity and noticeable rejection of arsenic, as one of the major environmental problems, were prepared from PSF/Brij‐58/NMP (1‐methyl‐2‐pyrrolidone) system via immersion precipitation. Pure water was used as gelation media. The variation effect of coagulation bath temperature (CBT) and addition of Brij‐58 on morphology, wettabiliy, pure water permeation flux and rejection of As (III) and As (V), as two dominant states of arsenic in the nature, were studied by scanning electron microscopy, contact angle measuring instrument and experimental setup. The results demonstrated that both hydrophilicity and rejection properties of the prepared membranes were significantly enhanced by small addition of Brij‐58 surfactant in the casting solution along with using the lowest level of CBT. Addition of 4 wt. % of Brij‐58 and using cold coagulation bath resulted in the highest rejection of As (V). Initial increase in Brij‐58 concentration, from 0 wt. % to 2 wt. %, resulted in higher rejection of As (III). However, higher Brij‐58 concentrations than 2 wt. % (increase from 2 wt. % to 6 wt. %) led to lower rejection of As (III). Also, it was found out that addition of Brij‐58 in the casting solution along with increasing the CBT resulted in formation of membranes with high permeability and sub‐layer porosity and thin top layer. Copyright © 2012 John Wiley & Sons, Ltd.     

Antibacterial photocatalytic self‐cleaning poly(vinylidene fluoride) membrane for dye wastewater treatment

Membrane technology has been successfully applied for the removal of dyes from wastewater in the textile industry. A novel poly(vinylidene fluoride) (PVDF) membrane was prepared via blending with different dosages of Ag‐TiO₂‐APTES composite for dyeing waste water treatment in our study. And the effect of Ag‐TiO₂‐APTES blended into the PVDF membrane was discussed, including the rejection rate of methylene blue (MB) dye, membrane morphology, surface hydrophilicity, antibacterial activity, and a certain photocatalytic self‐cleaning performance. X‐ray diffraction and Fourier transform infrared characterization confirmed that Ag‐TiO₂ was functionalized by amount of hydroxyl group (−OH) and amino group (NH−), which provided by APTES. Contact angle measurement certified that the hydrophilicity of the membrane surface increased, with the contact angle decrease to 61.4° compared with 81.8° of original PVDF membrane. MB rejection rate was also increased to 90.1% after addition of Ag‐TiO₂‐APTES, and the rejection of original membrane was only 74.3%. The morphologies of membranes were observed by scanning electron microscope, which indicated that Ag‐TiO₂‐APTES had a good dispersion in membrane matrix and also improved the microstructure of membranes. Besides, UV irradiation experiments were performed on the composite films contaminated by MB, and the result showed that Ag‐TiO₂‐APTES nanoparticle provided PVDF membrane with a certain photodegradation capacity under UV irradiation. Moreover, antibacterial activity of the composite membrane was also demonstrated through antibacterial experiment, Escherichia coli as the representative bacteria. Perhaps, this research may provide a new way for PVDF blending modification.     

Cellulose acetate nanocomposite ultrafiltration membranes tailored with hydrous manganese dioxide nanoparticles for water treatment applications

Hydrous manganese dioxide (HMO) nanoparticles incorporated cellulose acetate (CA) composite ultrafiltration (UF) membranes are prepared with the aim of improving the water permeation and BSA contaminant removal. The HMO nanoparticles are synthesized from manganese ion and characterized by FT‐IR, XRD, and FESEM. The effect of variation of HMO on CA membranes is probed using FT‐IR, EDAX, contact angle, SEM, and AFM analysis to demonstrate their chemical functionality, hydrophilicity, and morphology. CA/HMO membranes are showing the enhancement in pure water flux (PWF), water uptake, porosity, hydrophilicity, fouling resistance, BSA rejection, and flux recovery ratio (FRR). CA‐1 membrane displayed higher PWF (143.6 Lm²h^?1), BSA rejection (95.9%), irreversible fouling (93.3%), and FRR (93.3%). Overall results confirmed that the CA/HMO nanocomposite UF membranes overcome the bottlenecks and shows potential for water treatment applications.     

Preparation and recognition performance of cytisine alkaloid‐imprinted material prepared using novel surface molecular imprinting technique

Methacrylic acid was first graft‐polymerized on the surfaces of micron‐sized silica gel particles in the manner of “grafting from” using 3‐methacryloxypropyl trimethoxysilane as an intermedia, obtaining the grafted particle polymethacrylic acid PMAA/SiO₂. By adopting the novel surface‐molecular imprinting technique put forward by us, cytisine molecule‐imprinted material MIP‐PMAA/SiO₂ was prepared with ethylene glycol diglycidyl ether as crosslinking agent. The binding characteristics of MIP‐PMAA/SiO₂ towards cytisine was investigated in depth with both batch and column methods and using matrine and oxymatrine as two contrast alkaloids, which with cytisine coexist in sophora alopecuroides and their chemical structure is similar to cytisine to a certain extent. The experimental results show that the surface‐imprinted material MIP‐PMAA/SiO₂ has excellent binding affinity for cytisine (20.1 g/100 g of binding capacity), and it is more important that MIP‐PMAA/SiO₂ has very high recognition selectivity for cytisine in relation to the two contrast alkaloids. The selectivity coefficients of the grafted particles PMAA/SiO₂ (non‐imprinted material) for cytosine in relation to matrine and oxymatrine are only 1.03 and 1.06, respectively, displaying no recognition selectivity for cytisine. However, after imprinting, the selectivity coefficient of MIP‐PMAA/SiO₂ for cytisine in respect to matrine and oxymatrine are remarkably enhanced to 12.08 and 15.05, respectively.     

Preparation and properties of polysulfone/TiO2 composite ultrafiltration membranes

The influence of inorganic filler TiO₂ nanoparticles on the morphology and properties of polysulfone (PS) ultrafiltration membranes was investigated. PS/TiO₂ composite membranes were prepared by a phase‐inversion method. TiO₂ nanoparticles modified by sodium dodecyl sulfate were uniformly dispersed in an 18 wt % PS casting solution. The addition of TiO₂ resulted in an increase in the pore density and porosity of the membrane skin layer. The pore size distribution changed from the log‐normal distribution to the bimodal distribution because of the presence of TiO₂ nanoparticles, and some large pores were observed when the concentration of the filler was over 3 wt %. The skin layer was gradually thickened; meanwhile, the morphology sublayer changed from macrovoids to spongelike pores, in comparison with PS membranes without the filler. The addition of TiO₂ also induced increases in the hydrophilicity, mechanical strength, and thermal stability. The ultrafiltration experiments showed when the concentration of TiO₂ was less than 2 wt %, the permeability and rejection of the membrane was enhanced and then decreased drastically with a higher filler concentration (>3%). © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 879–887, 2006     

Synergistic effect of cocondensed nanosilica in intumescent flame‐retardant polypropylene

Amino‐functionalized nanosilica (SiO₂‐NH₂) was prepared through cocondensation method using aminopropyltriethoxysilane as comonomer to hydrolyze and cocondense with tetraethylorthosilicate. The synergistic effect of combination of ammonium polyphosphate and pentaerythritol with SiO₂‐NH₂ on the thermal and flame‐retardant properties of intumescent flame‐retardant (IFR) polypropylene (PP) has been investigated by thermogravimetric analysis (TGA), scanning electron microscopy, Raman spectra, X‐ray diffraction (XRD), limiting oxygen index (LOI), and UL 94 tests. When 1.0 wt.% SiO₂‐NH₂ was added, the LOI value of the PP/IFR composite with 25 wt.% of IFR increased from 26.6% to 31.7%, while the UL 94 rating raised from not classified to V‐0. The TGA data demonstrated that the SiO₂‐NH₂ nanoparticles increased the charred residue of the PP/IFR composites. The morphological structures and the orderliness of the charred residue proved that SiO₂‐NH₂ promoted the formation of compact intumescent charred layer, which effectively protected the underlying polymer from burning. The XRD patterns of the charred residue indicated that nanosilica reacted with APP to form SiP₂O₇ crystal structure during combustion, which was beneficial to the formation of compact charred layers. In comparison with the inorganic SiO₂‐cal nanoparticles, the amino‐functionalized nanosilica revealed much more efficient synergistic flame‐retardant effect due to the difference of surface properties.     

Well‐Defined SiO2@P(EtOx‐stat‐EI) Core–Shell Hybrid Nanoparticles via Sol‐Gel Processes

Positively charged nanoparticles (NPs) are very interesting for biomedical and pharmaceutical applications, such as nonviral gene delivery. Here, the synthesis of SiO₂ nanoparticles with a covalently grafted poly(2‐ethyl‐2‐oxazoline) (PEtOx) shell (SiO₂@PEtOx) is presented. PEtOx with a degree of polymerization of 20 and 38 is synthesized via microwave supported cationic ring‐opening polymerization and subsequently end‐functionalized with a triethoxysilyl linker for subsequent grafting to silica particles with hydrodynamic radii of 7, 31, and 152 nm. The resulting SiO₂@PEtOx particles are characterized by using dynamic light scattering (DLS), transmission electron microscopy (TEM, cryoTEM), and scanning electron microscopy (SEM) to determine changes in particle size. Thermal gravimetrical analysis is used to quantify the amount of polymer on the silica surface. Subsequent in situ transformation of SiO₂@PEtOx particles into SiO₂@P(EtOx‐stat‐EI) (poly(2‐ethyl‐2‐oxazoline‐stat‐ethylene imine) grafted silica particles) under acidic conditions inverts the surface charge from negative to positive according to ζ‐potential measurements. The P(EtOx‐stat‐EI) shell could be used for the deposition of Au NP afterward.

     

Mesoporous Silica‐coated Magnetic Nanoparticles for Mixed Hemimicelles Solid‐phase Extraction of Phthalate Esters in Environmental Water Samples with Liquid Chromatographic Analysis

To extract, preconcentrate and determine the trace level of environmental contaminants, a novel mixed hemimicelles solid‐phase extraction (MHSPE) method based on mesoporous silica‐coated magnetic nanoparticles (Fe₃O₄/meso‐SiO₂ NPs) as adsorbent was developed for extraction of phthalate esters from water samples. The Fe₃O₄/meso‐SiO₂ NPs were synthesized by using a combination of hydrothermal method and sol‐gel method. The obtained Fe₃O₄/meso‐SiO₂ NPs possessed a large surface area (570 m²/g), superparamagnetism, and uniform mesopores (2.8 nm). MHSPE parameters, such as the amount of surfactant, pH of sample, shaking and separation time, eluent and breakthrough volume that may influence the extraction of analytes greatly, were further investigated. Under the optimized conditions, the extraction was completed in 20 min and a concentration factor of 500 was achieved by extracting 250 mL water sample. Detection limits obtained of butyl‐benzyl phthalate (BBP), di‐n‐butyl phthalate (DnBP), di‐(2‐ethylhexyl) phthalate (DEHP) and di‐n‐cotyl phthalate (DnOP) were 12, 21, 12, and 32 ng/L, respectively. The proposed method exhibited high extraction efficiency and relatively short time for extracting the target compounds.     

Preparation of photocrosslinked sol‐gel composites based on urethane‐acrylic matrix,silsesquioxane sequences,TiO2, and Ag/Au Nanoparticles for use in photocatalytic applications

An acid urethane oligodimethacrylate based on poly(ethylene glycol) was synthesized and used in the preparation of hybrid composites containing silsesquioxane sequences and titania domains formed through sol‐gel reactions along with silver/gold nanoparticles (Ag/Au NPs) in situ photogenerated during the UV‐curing process. The photopolymerization kinetics studied by Fourier transform infrared spectroscopy and photoDSC showed that the photoreactivity of the investigated formulations depends on the amount of titanium butoxide (5–20 wt %) added in the system subjected to UV irradiation. The introduction of 1 wt % AgNO₃/AuBr₃ in formulations slightly improved the degree of conversion but diminished the polymerization rates. The formation of hybrid materials comprising predominantly amorphous TiO₂/SiO₂ NPs, with or without Ag/Au NPs, was confirmed through specific analyses. The evaluation of photocatalytic activity demonstrated that the synthesized hybrid films are suitable for the complete removal of organic pollutants (phenolic compounds) from water under UV irradiation (200–350 min) at low intensity (found in the solar radiation). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1189–1204     

Impact of TiO2 nanoparticles on morphology and performance of crosslinked polyimide organic solvent nanofiltration (OSN) membranes

Chemically crosslinked polyimide organic–inorganic composite nanofiltration membranes suitable for application in harsh organic solvents were successfully prepared by phase inversion of dope solutions. TiO₂ nanoparticles were dispersed in these dope solutions, comprising polyimide (PI) in N,N-dimethylformamide/1,4-dioxane. The impact of TiO₂ on the resulting PI membranes was investigated using SEM, TGA, water contact angle, dope viscosity measurements and mechanical strength. The presence of TiO₂ nanoparticles within the membrane matrix was proved by the detection of a peak characteristic of TiO₂ in the WAXS pattern. SEM pictures of the cross-section of the PI/TiO₂ membranes showed dramatically changed morphology compared to reference membranes with no TiO₂ addition. Macrovoids present in reference membranes were suppressed by increasing loading of TiO₂ nanoparticles, and eventually disappeared completely at a TiO₂ loading above 3 wt.%. Decreasing water contact angle and an increase in ethanol flux indicated that hydrophilicity increased as nanoparticle loading increased. The effect of TiO₂ on the functional performance of the membranes was evaluated by measuring flux and rejection using cross-flow filtration. Perhaps surprisingly, the presence of TiO₂ improved the compaction resistance of the membranes, whereas rejection and steady flux were almost unaltered.     

Well‐defined polyisoprene‐grafted silica nanoparticles via the RAFT process

The preparation of well‐defined polyisoprene‐grafted silica nanoparticles (PIP‐g‐SiO₂ NPs) was investigated. Surface initiated reversible addition fragmentation chain transfer (SI‐RAFT) polymerization was used to polymerize isoprene from the surface of 15 nm silica NPs. A high temperature stable trithiocarbonate RAFT agent was anchored onto the surface of particles with controllable graft densities. The polymerization of isoprene mediated by silica anchored RAFT with different densities were investigated and compared to the polymerization mediated by free RAFT agents. The effects of different temperatures, initiators, and monomer feed ratios on the kinetics of the SI‐RAFT polymerization were also investigated. Using this technique, block copolymers of polyisoprene and polystyrene on the surface of silica particles were also prepared. The well‐defined synthesized PIP‐g‐SiO₂ NPs were then mixed with a polyisoprene matrix which showed a good level of dispersion throughout the matrix. These tunable grafted particles have potential applications in the field of rubber nanocomposites. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 1493–1501     

Functional membranes prepared by layer‐by‐layer assembly and its metal ions adsorption property

PVDF/(PEI‐C/PAA)_n functional membranes were prepared by layer‐by‐layer (LbL) assembly, and their heavy metal ions adsorption capability was investigated. The changes in the chemical compositions of membrane surfaces were determined by X‐ray photoelectron spectroscopy (XPS). XPS results show that the surface of the PVDF membrane can be alternatively functionalized by PEI‐C and PAA. The membrane surface hydrophilicity was evaluated through water contact angle measurement. Contact angle results show that the surface hydrophilicity of the membrane surface depends on the outermost deposited layer. Morphological changes of membrane surfaces were observed by scanning electron microscopy (SEM). The water fluxes for these membranes were elevated after modification. The performances of the PVDF/(PEI‐C/PAA)_n membranes on the adsorption of copper ions (Cu²⁺) from aqueous solutions were investigated by inductively coupled plasma (ICP). The results indicate that the PVDF/(PEI‐C/PAA)_n functional membranes show high copper ions adsorption ability. Copyright © 2010 John Wiley & Sons, Ltd.     

Chemically functionalized silica nanoparticles‐based solid‐phase extraction for effective pre‐concentration of highly toxic metal ions from food and water samples

In this research study, an efficient solid‐phase extraction procedure based on a new organometallic, effective, eco‐friendly and bio‐degradable nanoadsorbent was firstly introduced for influential pre‐concentration of Cu(II), Zn(II), Pb(II), Cd(II) and Mn(II) ions from food and water samples followed by flame atomic absorption spectrophotometric determination. This safe adsorbent consisted of silica nanoparticles chemically functionalized with di‐ethylen tri‐amine (SiO₂@NH₂NPs); easily prepared via an effective and simple approach. Characterization of SiO₂@NH₂NPs was subsequently implemented via SEM, FT‐IR and XRD; certifying high quality of the modified nanoadsorbent in terms of size, shape and surface functional groups. The effects of the main factors on the extraction efficiency were then optimized. Efficient extraction of the analytes of interest at neutral media accompanied with the aid of a bio‐compatible organometallic nanoadsorbent can be considered as valuable advantages of the proposed approach. In the optimum conditions, calibration graphs were linear in the range of 4–700 μg l^?1, with higher correlation coefficients than 0.997 and limits of detection of 1.45–4.10 ng ml^?1. The enrichment factor values were found to be in the span of 120–400. The resultant extraction recovery values were satisfactory; possessing the proper relative standard deviation (%, n  =  5) values of 2.05–4.28%.     

Programmed Synthesis by Stimuli‐Responsive DNAzyme‐Modified Mesoporous SiO2 Nanoparticles

DNAzyme‐capped mesoporous SiO₂ nanoparticles (MP SiO₂ NPs) are applied as stimuli‐responsive containers for programmed synthesis. Three types of MP SiO₂ NPs are prepared by loading the NPs with Cy3‐DBCO (DBCO=dibenzocyclooctyl), Cy5‐N₃, and Cy7‐N₃, and capping the NP containers with the Mg²⁺, Zn²⁺, and histidine‐dependent DNAzyme sequences, respectively. In the presence of Mg²⁺ and Zn²⁺ ions as triggers, the respective DNAzyme‐capped NPs are unlocked, leading to the “click” reaction product Cy3‐Cy5. In turn, in the presence of Mg²⁺ ions and histidine as triggers the second set of DNAzyme‐capped NPs is unlocked leading to the Cy3‐Cy7 conjugated product. The unloading of the respective NPs and the time‐dependent formation of the products are followed by fluorescence spectroscopy (FRET). A detailed kinetic model for the formation of the different products is formulated and it correlates nicely with the experimental results.     

Influence of polypropylene membrane surface porosity on the performance of membrane distillation process

Two kinds of polypropylene capillary membranes were used in the membrane distillation (MD). These membranes exhibited a similar morphology, but one of them has an additional low porosity layer on the internal surface of capillaries. The changes of membrane performance during MD process of tap water were investigated. The presence of low porosity layer (thickness below 1 μm) caused that the air permeability was reduced from 1.365 to 0.863 dm³/m² s kPa, whereas the MD permeate flux was decreased only by 15%. A significantly larger decline of the flux was caused by CaCO₃ deposit formed during distillation of tap water. This deposit was removed every 30–70 h by rinsing the modules with a 2–5 wt.% HCl. Unfortunately, a repetition of this operation several times resulted in a gradual decline of the maximum permeate flux (distilled water as a feed). However, the module efficiency with the membranes covered by a surface layer of low porosity was found to decreases twice as slowly. The investigations revealed that a low surface porosity does not limit the possibility of surface wetting of polypropylene membranes, but hindered the scale formation inside the pores.