Poly(lactic acid)/(styrene‐ethylene‐butylene‐styrene)‐g‐maleic anhydride copolymer/sepiolite nanocomposites: Investigation of thermo‐mechanical and morphological properties

In this study, sepiolite nanoclay is used as reinforcing agent for poly(lactic acid) (PLA)/(styrene‐ethylene‐butylene‐styrene)‐g‐maleic anhydride copolymer (SEBS‐g‐MA) 90/10 (w/w) blend. Effects of sepiolite on thermal behavior, morphology, and thermomechanical properties of PLA/SEBS‐g‐MA blend were investigated. Differential scanning calorimetry results showed 7% improvement in crystallinity at 0.5 wt% of sepiolite. The nanocomposite exhibited approximately 36% increase in the tensile modulus and 17% increase in toughness as compared with the blend matrix at 0.5 and 2.5 wt% of sepiolite respectively. Field emission scanning electron microscopy and transmission electron microscopy images exhibited sepiolite‐induced morphological changes and dispersion of sepiolite in both PLA and SEBS‐g‐MA phases. Dynamic mechanical analysis and wide angle X‐ray diffraction present evidences in support of the reinforcing nature of sepiolite and phase interaction between the filler and the matrix. This study confirms that sepiolite can improve tensile modulus and toughness of PLA/SEBS‐g‐MA blend.     

Effects of different types of polyethylene on the morphology and properties of recycled poly(ethylene terephthalate)/polyethylene compatibilized blends

Recycled poly(ethylene terephthalate) (R‐PET) was blended with four types of polyethylene (PE), linear low density polyethylene (LLDPE; LL0209AA, Fs150), low density polyethylene (LDPE; F101‐1), and metallocene‐LLDPE (m‐LLDPE; Fv203) by co‐rotating twin‐screw extruder. Maleic anhydride‐grafted poly(styrene‐ethylene/butyldiene‐styrene) (SEBS‐g‐MA) was added as compatibilizer. R‐PET/PE/SEBS‐g‐MA blends were examined by scanning electron microscopy (SEM), differential scanning calorimeter (DSC), dynamic mechanical analysis (DMA), and mechanical property testing. The results indicated that the morphology and properties of the blends depended to a great extent on the miscibility between the olefin segments of SEBS‐g‐MA and PE. Due to the proper interaction between SEBS‐g‐MA and LDPE (F101‐1), most SEBS‐g‐MA, located at the interface between two phases of PET and LDPE to increase the interfacial adhesion, lead to better mechanical properties of R‐PET/LDPE (F101‐1) blend. However, both the poor miscibility of SEBS‐g‐MA with LLDPE (LL0209AA) and the excessive miscibility of SEBS‐g‐MA with LLDPE (Fs150) and m‐LLDPE (Fv203) reduced the compatibilization effect of SEBS‐g‐MA. DSC results showed that the interaction between SEBS‐g‐MA and PE obviously affected the crystallization of PET and PE. DMA results indicated that PE had more influence on the movement of SEBS‐g‐MA than PE did. Copyright © 2010 John Wiley & Sons, Ltd.     

Impact‐modified polypropylene/vermiculite nanocomposites

Impact‐modified polypropylene (PP)/vermiculite (VMT) nanocomposites toughened with maleated styrene–ethylene butylene–styrene (SEBS‐g‐MA) were compounded in a twin‐screw extruder and injection‐molded. VMT was treated with maleic anhydride, which acted both as a compatibilizer for the polymeric matrices and as a swelling agent for VMT in the nanocomposites. The effects of the impact modifier on the morphology and the impact, static, and dynamic mechanical properties of the PP/VMT nanocomposites were investigated. Transmission electron microscopy revealed that an exfoliated VMT silicate layer structure was formed in ternary (PP–SEBS‐g‐MA)/VMT nanocomposites. Tensile tests showed that the styrene–ethylene butylene–styrene additions improved the tensile ductility of the (PP–SEBS‐g‐MA)/VMT ternary nanocomposites at the expense of their tensile stiffness and strength. Moreover, Izod impact measurements indicated that the SEBS‐g‐MA addition led to a significant improvement in the impact strength of the nanocomposites. The SEBS‐g‐MA elastomer was found to be very effective at converting brittle PP/VMT organoclay composites into tough nanocomposites. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2332–2341, 2003     

氢化苯乙烯-丁二烯-苯乙烯嵌段共聚物及其马来酸酐接枝共聚物增韧聚对苯二甲酸乙醇酯共混材料的辐射效应

采用双螺杆熔融共混的方法制备了含三羟甲基丙烷三丙烯酸酯(TMPTA)的聚对苯二甲酸乙二酯/氢化苯乙烯-丁二烯-苯乙烯嵌段共聚物（PET/SEBS）和聚对苯二甲酸乙二酯/马来酸酐接枝氢化苯乙烯-丁二烯-苯乙烯嵌段共聚物（PET/SEBS-g-MAH）共混材料,并在Co-60源中对其进行辐照。 通过对共混材料的力学性能、相态结构测和凝胶含量分析,对比研究了辐射对以上2种共混材料结构及性能的影响。 扫描电子显镜观察和凝胶含量分析结果表明,在适量TMPTA存在时,辐射有效地改善了PET/SEBS体系的相容性。 冲击强度的变化证实了这种增容效应,当SEBS的质量分数为20%、TMPTA质量分数为1%,经50 kGy辐照后,冲击强度达到17.3 kJ/m2。 当在SEBS分子链上引入马来酸酐官能团,辐照后,体系的相态结构变化并不明显,冲击强度最大值仅为11.5 kJ/m2,明显低于不含马来酸酐官能团的体系。     

Combined effect of compatibilizer and carbon nanotubes on the morphology and electrical conductivity of PP/PS blend

In this work, maleic anhydride grafted styrene–ethylene–butadiene–styrene copolymer (SEBS‐g‐MA) and carbon nanotubes (CNTs) were introduced into the immiscible polypropylene/polystyrene (PP/PS) blend. Among the three polymer components, SEBS‐g‐MA has the strongest affinity to CNTs; thus, it exhibits dual effects to adjust the phase morphology of the blends and the dispersion state of CNTs in the blends. The experimental observations obtained from morphology characterizations using scanning electron microscope and transmission electron microscope confirm the selective localization of CNTs at the interface of the immiscible PP/PS blend. As a consequence, largely decreased percolation threshold is achieved when most of CNTs are selectively localized at the interface region between PP and PS. Copyright © 2014 John Wiley & Sons, Ltd.     

Nanotailoring of sepiolite clay with poly [styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene]: structure–property correlation

Poly [styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS)/sepiolite clay nanocomposites are prepared by solvent casting method. Two types of schemes have been adopted to establish the compatibility between nonpolar polymer (SEBS) and needle‐like inorganic filler (sepiolite), either by polar modification of the nonpolar polymer or organic modification of the inorganic filler. Structure–property correlation of nanocomposites derived from two different approaches is compared. Structural and morphological analysis of nanocomposites has been investigated by Fourier transform infrared spectroscopy, X‐ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. Fourier transform infrared result shows better compatibility between SEBS and modified sepiolite clay compared to maleic anhydride grafted SEBS and pristine sepiolite in their nanocomposites. Tensile strength and % elongation are found to increase by 32 and 105%, respectively, with the addition of just 3 parts per hundred parts of resin (phr) modified sepiolite clay to pristine SEBS matrix. Moreover, thermal stability has also improved by 96°C with similar loading. This work provides a new insight into the structure and thermo‐mechanical properties of novel SEBS–sepiolite clay nanocomposites. Copyright © 2017 John Wiley & Sons, Ltd.     

Effect of novel compatibilizers on the properties and morphology of PP/PC blends

A series of compatibilizers, including polypropylene (PP) grafted with 2‐tertbutyl‐6‐(3‐tertbutyl‐ 2‐hydroxy‐5‐methylbenzyl)‐4‐methylphenyl acrylic ester (BPA), glycidyl methacrylate (GMA), GMA/styrene (GMA‐st), and 2‐allyl bisphenol A (2A) were investigated for the purpose of improving the compatibility of PP/polycarbonate (PC) blends. PP‐g‐BPA shows a remarkable compatibilizing effect on PP/PC blends since it has similar group‐benzene ring with PC, and it is a sort of heat‐resistant antioxidant in the meantime, which can reduce the molecular degradation of PP during grafting and blending under high temperatures. Its compatibilizing effect was examined in terms of the mechanical, thermal properties, and morphologies. PP/PC blends show a decreasing and much more homogeneous size of dispersed PC particles through addition of a small amount of PP‐g‐BPA, and dynamic mechanical analysis (DMA) reveals a noticeable approach of T_g between PP and PC, indicating the improvement of the compatibility of PP/PC blends. Furthermore, styrene‐ethylene‐butylene‐styrene (SEBS) as a toughening rubber and a compatibilizer was applied to PP/PC blends. Around 25 wt% SEBS and 20 wt% PC lead to high toughness and strength of PP. Copyright © 2008 John Wiley & Sons, Ltd.     

The effect of various compatibilizers on thermal,mechanical, and morphological properties of polystyrene/polypropylene blends

The effects of various compatibilizers on thermal, mechanical and morphological properties of 50/50 polypropylene/polystyrene blends were investigated. Various compatibilizers, polystyrene-(ethylene/butylenes/ styrene) (SEBS), ethylene vinyl acetate (EVA), polystyrene-butylene rubber (SBR) and blend of compatibilizers SEBS/PP-g-MAH, EVA/PP-g-MAH, and SBR/PP-g-MAH were used. Differential scanning calorimetry, thermogravimetric analysis, wide-angle X-ray scattering, scanning electron microscopy, microhardness, and Izod impact strength were adopted. It was found that the influence of various compatibilizers was appeared on all the properties studied. The properties of the blends compatibilized with SEBS, EVA, and SBR are very distinct from those of blends compatibilized with blend of compatibilizers. Results show that compatibilized blends with the blend of compatibilizers EVA/PP-g-MAH, SBR/PP-g-MAH, and SEBS/PP-g-MAH or SBR were relatively more stable than the uncompatibilized blend and blend compatibilized with SEBS or EVA. The compatibilizer does not only reduce the interfacial tension or increase the phase interfacial adhesion between the immiscible polymers, but greatly affects the degree of crystallinity of blends.

     

Polyamide 66/EPR‐g‐MA blends: mechanical modeling and kinetic analysis of thermal degradation

The present investigation deals with the mechanical, thermal, and morphological properties of binary nylon 66/maleic anhydride grafted ethylene propylene rubber (EPR‐g‐MA) blends at different dispersed phase (EPR‐g‐MA) concentrations. The effects of EPR‐g‐MA concentration and dispersed particle size on the mechanical properties of the blends were studied. Analysis of the tensile data in terms of various theoretical models revealed the variation of stress concentration effect with blend composition and the improvement of interfacial adhesion between dispersed rubber phase and nylon 66 matrix. The thermal degradation of the blends was analyzed by nonisothermal thermogravimetric analysis (TGA). It was found that the activation energy (E_a) and overall reaction order of thermal degradation decreased with increasing EPR‐g‐MA content. The scanning electron microscopic (SEM) analysis showed a significant decrease in dispersed particle size with increasing EPR‐g‐MA content, which was explained on the basis of the level of chemical interaction (in situ compatibilization) between nylon 66 and EPR‐g‐MA. The surface morphology of the nylon 66/EPR‐g‐MA blends was illustrated by the roughness of atomic force microscopy (AFM) images. Copyright © 2008 John Wiley & Sons, Ltd.     

Polypropylene/montmorillonite nanocomposites toughened with SEBS‐g‐MA: Structure–property relationship

Polypropylene (PP)/organo‐montmorillonite (Org‐MMT) nanocomposites toughened with maleated styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MA) were prepared via melt compounding. The structure, mechanical properties, and dynamic mechanical properties of PP/SEBS‐g‐MA blends and their nanocomposites were investigated by X‐ray diffraction (XRD), polarizing optical microscopy (POM), tensile, and impact tests. XRD traces showed that Org‐MMT promoted the formation of β‐phase PP. The degree of crystallinity of PP/SEBS‐g‐MA blends and their nanocomposites were determined from the wide angle X‐ray diffraction via profile fitting method. POM experiments revealed that Org‐MMT particles served as nucleating sites, resulting in a decrease of the spherulite size. The essential work of fracture approach was used to evaluate the tensile fracture toughness of the nanocomposites toughened with elastomer. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3112–3126, 2005     

Impact‐specific essential work of fracture of maleic anhydride‐compatibilized polypropylene/elastomer blends and their composites

Charpy drop‐weight‐impact and essential work of fracture (EWF) characteristics of maleic anhydride (MA)‐compatibilized styrene–ethylene butylene–styrene (SEBS)/polypropylene (PP) blends and their composites reinforced with short glass fibers (SGFs) were investigated. MA was grafted to either SEBS copolymer (SEBS‐g‐MA) or PP (PP‐g‐MA). The mPP blend was prepared by the compounding of 95% PP and 5% PP‐g‐MA. Drop‐weight‐impact results revealed that the mPP specimen had an extremely low impact strength. The incorporation of SEBS or SEBS‐g‐MA elastomers into mPP improved its impact strength dramatically. Similarly, the addition of SEBS was beneficial for enhancing the impact strength of the SGF/SEBS/mPP and SGF/SEBS‐g‐MA/mPP hybrids. A scanning electron microscopy examination of the fractured surfaces of impact specimens revealed that the glass‐fiber surfaces of the SGF/SEBS/mPP and SGF/SEBS‐g‐MA/mPP hybrids were sheathed completely with deformed matrix material. This was due to strong interfacial bonding between the phase components of the hybrids associated with the MA addition. Impact EWF tests were carried out on single‐edge‐notched‐bending specimens at 3 m s^?1. The results showed that pure PP, mPP, and the composites only exhibited specific essential work. The nonessential work was absent in these specimens under a high‐impact‐rate loading condition. The addition of SEBS or SEBS‐g‐MA elastomer to mPP increased both the specific essential and nonessential work of fracture. This implied that elastomer particles contributed to the dissipation of energy at the fracture surface and in the outer plastic zone at a high impact speed of 3 m s^?1. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1881–1892, 2002     

Compatibilization level effects on the structure and mechanical properties of rubber‐modified polyamide‐6/clay nanocomposites

Exfoliated polyamide‐6 (PA6)/organically modified montmorillonite clay (OMMT) nanocomposites (PNs) were modified with partially maleinized styrene–ethylene/butadiene–styrene triblock copolymers (SEBS) at three maleinization levels in an attempt to link in these materials high toughness with appropriate small‐strain and fracture tensile properties. OMMT stayed only in the PA6 matrix, and no preferential location in the matrix/rubber interphase was observed. The increased dispersed phase size upon the addition of OMMT was attributed to interactions between maleic anhydride (MA) functionalized SEBS and the surfactant of OMMT. The rubber particle size generally decreased when the MA content of SEBS increased, and this indicated compatibilization. The subsequent good adhesion led to tough nanocomposites across a wide range of both strain rates and fracture modes. As the critical interparticle distance (τ_c) decreased with the MA content, and the other parameters that could influence the surface‐to‐surface mean interparticle distance did not change, it is proposed that in these PNs higher adhesion leads to a smaller τ_c value. Finally, the presence in the matrix of a nanostructured clay makes the rubber content necessary for the toughness jump to increase and τ_c to decrease. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3611–3620, 2005     

Dynamically vulcanized ethylene propylene diene terpolymer/nylon thermoplastic elastomers

A thermoplastic elastomer (TPE) of ethylene propylene diene terpolymer (EPDM) and nylon with excellent mechanical properties was prepared by dynamic vulcanization. The effects of the curing systems, compatibilizer, nylon content and reprocessing on the mechanical properties of EPDM/nylon TPEs were investigated in detail. Experimental results indicate that maleic anhydride (MAH) grafted EPR has a better performance in compatibilizing the EPDM/nylon blends compared with other compatibilizers containing acid group. Tensile strength and elongation at break go through a maximum value at a compatibilizer resin content (on total rubber dosage) of 20%. EPDM/nylon TPE using sulfur as curative has higher tensile strength and elongation than that of TPE using phenolic resin or peroxide as curatives. Tensile strength and elongation at break increase with increasing nylon content. Scanning electron microscopy results show that rubber particles distributed at an average size of 1 μm in dynamic vulcanized EPDM/MAH-g-EPR/nylon TPE.     

Structural and mechanical behavior of polypropylene/ maleated styrene‐(ethylene‐co‐butylene)‐styrene/sisal fiber composites prepared by injection molding

Hybrid composites consisting of isotactic poly(propylene) (PP), sisal fiber (SF), and maleic anhydride grafted styrene‐(ethylene‐co‐butylene)‐styrene copolymer (MA‐SEBS) were prepared by melt compounding, followed by injection molding. The melt‐compounding torque behavior, thermal properties, morphology, crystal structure, and mechanical behavior of the PP/MA‐SEBS/SF composites were systematically investigated. The torque test, thermogravimetric analysis, differential scanning calorimetric, and scanning electron microscopic results all indicated that MA‐SEBS was an effective compatibilizer for the PP/SF composites, and there was a synergism between MA‐SEBS and PP/SF in the thermal stability of the PP/MA‐SEBS/SF composites. Wide‐angle X‐ray diffraction analysis indicated that the α form and β form of the PP crystals coexisted in the PP/MA‐SEBS/SF composites. With the incorporation of MA‐SEBS, the relative amount of β‐form PP crystals decreased significantly. Mechanical tests showed that the tensile strength and impact toughness of the PP/SF composites were generally improved by the incorporation of MA‐SEBS. The instrumented drop‐weight dart‐impact test was also used to examine the impact‐fracture behavior of these composites. The results revealed that the maximum impact force (F_max), impact‐fracture energy (E_T), total impact duration (t_r), crack‐initiation time (t_init), and crack‐propagation time (t_prop) of the composites all tended to increase with an increasing MA‐SEBS content. From these results, the incorporation of MA‐SEBS into PP/SF composites can retard both the crack initiation and propagation phases of the impact‐fracture process. These prolonged the crack initiation and propagation time and increased the energy consumption during impact fracture, thereby leading to toughening of PP/MA‐SEBS/SF composites. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1214–1222, 2002     

Does nanoclay addition always lead to amelioration? Dual effects of the nanoclay on the PA‐6/EVOH/SEBS ternary blends

This work presents the investigation of properties of polyamide‐6 (PA‐6)/ethylene vinyl alcohol (EVOH)/styrene‐ethylene‐butylene‐styrene (SEBS) ternary blends and related nanocomposites with nanoclays. In this way, the effect of the mixing protocol and nanoclay type on the morphology, mechanical, and rheological properties of the blends was comprehensively studied. Scanning electron microscopy (SEM) observation revealed that, for the neat ternary blends, core‐shell droplets were formed in which SEBS droplets were encapsulated by EVOH phase in the PA‐6 matrix. In this regard, experimental observations were compared and discussed with the predictions of phenomenological models. According to the X‐ray diffraction analysis, the distribution and degree of dispersion of the nanoclays were significantly influenced by mixing protocol. It was demonstrated that competition between the intrinsic effect of the nanoclay on the physical properties and its inhibiting effect on the interactions between PA‐6 and EVOH phases led to some interesting observations for the rheological and mechanical properties of the ternary blends. The results revealed that optimum properties could be obtained by selecting appropriate nanoclay and mixing protocol.     

Improvement of Impact Strength of Polylactide Blends with a Thermoplastic Elastomer Compatibilized with Biobased Maleinized Linseed Oil for Applications in Rigid Packaging

This research work reports the potential of maleinized linseed oil (MLO) as biobased compatibilizer in polylactide (PLA) and a thermoplastic elastomer, namely, polystyrene-b-(ethylene-ran-butylene)-b-styrene (SEBS) blends (PLA/SEBS), with improved impact strength for the packaging industry. The effects of MLO are compared with a conventional polystyrene-b-poly(ethylene-ran-butylene)-b-polystyrene-graft-maleic anhydride terpolymer (SEBS-g-MA) since it is widely used in these blends. Uncompatibilized and compatibilized PLA/SEBS blends can be manufactured by extrusion and then shaped into standard samples for further characterization by mechanical, thermal, morphological, dynamical-mechanical, wetting and colour standard tests. The obtained results indicate that the uncompatibilized PLA/SEBS blend containing 20 wt.% SEBS gives improved toughness (4.8 kJ/m²) compared to neat PLA (1.3 kJ/m²). Nevertheless, the same blend compatibilized with MLO leads to an increase in impact strength up to 6.1 kJ/m², thus giving evidence of the potential of MLO to compete with other petroleum-derived compatibilizers to obtain tough PLA formulations. MLO also provides increased ductile properties, since neat PLA is a brittle polymer with an elongation at break of 7.4%, while its blend with 20 wt.% SEBS and MLO as compatibilizer offers an elongation at break of 50.2%, much higher than that provided by typical SEBS-g-MA compatibilizer (10.1%). MLO provides a slight decrease (about 3 °C lower) in the glass transition temperature (T_g) of the PLA-rich phase, thus showing some plasticization effects. Although MLO addition leads to some yellowing due to its intrinsic yellow colour, this can contribute to serving as a UV light barrier with interesting applications in the packaging industry. Therefore, MLO represents a cost-effective and sustainable solution to the use of conventional petroleum-derived compatibilizers.     

Preparation, structure, and properties of styrene-ethylene-butylene-styrene block copolymer/clay nanocomposites: Part II fracture behaviors

Styrene-ethylene-butylene-styrene block copolymer (SEBS)/clay nanocomposites were prepared via a melt mixing technique. Various amounts of two types of maleated compatibilizers, styrene-ethylene-butylene-styrene block copolymer grafted maleic anhydride (SEBS-g-MA) and polypropylene grafted maleic anhydride (PP-g-MA), were incorporated to improve the dispersion of commercial organoclay (denoted as 20A), respectively. PP-g-MA compatibilized system conferred higher tensile strength and tear strength (initiation condition) than SEBS-g-MA compatibilized system. At a fixed content of compatibilizers, the above mechanical properties were improved with increasing clay content as well. By relating tensile strength to tear strength (arrest condition), the average depth of flaw was in the range of 33.8 ± 3.4 μm, which successfully confirmed the extension of Rivlin and Thomas’s theory for conventional elastomers to thermoplastic elastomer/clay nanocomposites for the first time. Cutting strength of SEBS/clay nanocomposites gave an intermediate value when compared with crystalline plastics and conventional amorphous elastomers, which further signified the importance of micro-yielding of styrene domains, crystalline yielding of compatibilizer, and filler reinforcement even in the nano-fracture zone of deformation.     

Reactive melt blends of thermoplastic polyolefins,MAH‐g‐PP and nylon 6

Reactive melt blends of an ethylene‐propylene‐diene terpolymer (EPDM) based thermoplastic elastomer (TPE), maleic anhydride grafted polypropylene (MAH‐g‐PP), and nylon 6 were prepared in a single screw extruder and evaluated in terms of morphological, rheological, thermal, dynamic mechanical, and mechanical properties of the blends. It was found that MAH‐g‐PP‐co‐nylon 6 copolymers were in situ formed and acted as effective compatibilizers for polypropylene (PP) and nylon 6. Phase separation of PP and EPDM in TPE increased with the addition and increasing amount of MAH‐g‐PP and nylon 6, leading to decreased glass transition temperature (T_g) of TPE and increased crystalline melting temperature (T_m) of PP. Copyright © 2004 John Wiley & Sons, Ltd.     

Use of maleic anhydride compatibilization to improve toughness and other properties of polylactide blended with thermoplastic elastomers

Polylactide (PLA) being a very brittle biopolymer could be toughened by blending with thermoplastic elastomers such as thermoplastic polyurethane elastomer (TPU) and thermoplastic polyester elastomer (TPE); unfortunately, these blends are immiscible forming round domains in the PLA matrix. Therefore, the purpose of this study was to investigate the effects of using maleic anhydride (MA) compatibilization on the toughness and other properties of PLA blended with TPU and TPE. MA grafting on the PLA backbone (PLA‐g‐MA) was prepared separately by reactive extrusion and added during melt blending of PLA/thermoplastic elastomers. IR spectroscopy revealed that MA graft might interact with the functional groups present in the hard segments of TPU and TPE domains via primary chemical reactions, so that higher level of compatibilization could be obtained. SEM studies indicated that PLA‐g‐MA compatibilization also decreased the size of elastomeric domains leading to higher level of surface area for more interfacial interactions. Toughness tests revealed that Charpy impact toughness and fracture toughness (K_IC and G_IC) of inherently brittle PLA increased enormously when the blends were compatibilized with PLA‐g‐MA. For instance, G_IC fracture toughness of PLA increased as much as 166%. It was also observed that PLA‐g‐MA compatibilization resulted in no detrimental effects on the other mechanical and thermal properties of PLA blends. Copyright © 2014 John Wiley & Sons, Ltd.     

Compatibilizing effect of functionalized polystyrene blends: a study of morphology,thermal, and mechanical properties

Polystyrene (PS), being an amorphous polymer is immiscible with other polymers. To engender miscible blends, PS has been functionalized with an active amino‐functional group on the molecular chains of PS to yield amino‐substituted polystyrene (APS), which serves as a reactive compatibilizer. The compatibilization effect of amino functionalized polystyrene on the rubber toughening was explored and results were compared in terms of morphology, thermal, and mechanical properties of PS/SEBS‐g‐MA versus APS/SEBS‐g‐MA blends. In addition, the effect of rubber content on the blend morphology and mechanical properties were investigated. An appreciable change in the thermal stability of APS blends in comparison with PS blend has been probed. A marked correlation has been observed between phase morphology and thermal stability. Use of APS produced the compatibilized blends which render improved blend morphology, enhanced thermal and mechanical properties. Optimal thermal, morphological and mechanical profiles were depicted by 20‐wt% APS blend. Copyright © 2008 John Wiley & Sons, Ltd.