Two-pass amplification of CW laser by Nd/Cr:YAG ceramic Active mirror under lamp light pumping

The concept of an Active mirror with transparent Nd/Cr:YAG ceramics is proposed. A new ceramic material pumped by an arc-metal-halide lamp has been experimentally implemented. CW-laser light generated in a 1064 nm Nd:YAG micro-tip oscillator was amplified by an Active mirror made of Nd/Cr:YAG ceramic and pumped by CW arc-lamp light. The saturation power density of the Nd/Cr:YAG ceramic was lower than that of Nd:YAG because the stimulated-cross-section and lifetime were effectively enhanced by the sensitization of Cr ions. The maximum output laser power while keeping spatial beam quality was up to 3 W with an input lamp power of 9 W; the resulting optical-optical conversion efficiency of 33% was close to the theoretical prediction of nearly 50%.     

High-power, high-repetition-rate mid-infrared generation with PE-SRO based on a fan-out periodically poled MgO-doped lithium niobate

We present a high-average-power, pulsed mid-infrared pump-enhanced singly-resonant optical parametric oscillator (PE-SRO) using a fan-out periodically poled MgO-doped lithium niobate (MgO:PPLN). The pump laser is a Q-switched Nd:YAG laser with a repetition rate of 10 kHz. When the pump power was 22.0 W, a maximum idler output power of 3.4 W at 3781.4 nm was obtained. The thermal guiding effect caused by signal absorption was observed and the crystal heating power was measured with a new method.     

219.3 W CW diode-side-pumped 1123 nm Nd:YAG laser

We demonstrate a high power continuous wave (CW) diode-side-pumped Nd:YAG laser operating at 1123 nm with a plano-plano configuration. By means of precise coating, a single 1123 nm wavelength is achieved. Under the pump power of 1080 W, an output power of 219.3 W is obtained, which corresponds to an optical-optical conversion efficiency of 20.3%. To the best of our knowledge, this is the highest output power for CW 1123 nm laser based on Nd:YAG crystal.     

108 W Nd: YAG ceramic laser with birefringence compensation resonator

The quartz rotator's effective birefringence compensation for ceramic Nd:YAG rods has been first demonstrated. Furthermore, a high output power continuous-wave laser is presented based on an optimized resonator made up of four Nd:YAG ceramic rods. By an appropriate design of the resonator, an output power of 108 W at 1064 nm is obtained. The corresponding optical-to-optical conversion efficiency is 16.8% and the slope efficiency is 28.1%. Meanwhile, the numerical analysis for output power is detailed.     

Compact low threshold Cr:YAG passively Q-switched intracavity optical parametric oscillator

We report a compact KTP-based intracavity optical parametric oscillator (IOPO) driven by a diode-end-pumped passively Q-switched Nd:YVO₄/Cr:YAG laser. For the first time, we take the thermal lens effect of the Cr:YAG into consideration and discuss its impact on the signal output. Diode pump threshold as low as 0.52 W has been achieved, which is the lowest result reported to date. At the incident diode pump power of 4 W, we obtained the maximum signal average and peak power of 358 mW and 12.5 kW, respectively, corresponding to a diode-to-signal conversion efficiency of 9%. Moreover, cavity-dumping characteristic and pulse transforming process from 1064 to 1573 nm are qualitatively analyzed.     

QCW diode-side-pumped Nd:YAG ceramic laser with 247 W output power at 1123 nm

We demonstrate for the first time a diode-side-pumped quasi-continuous-wave (QCW) operation of a 1123 nm Nd:YAG ceramic laser. The single 1123 nm wavelength is acquired through precise coating. With a pump power of 1000 W, an output power of 247 W is obtained, corresponding to an optical–optical conversion efficiency of 24.7%. At the maximal output power, the pulse repetition rate and pulse width are measured to be 1.1 kHz and 180 μs, respectively. The numerical simulations for wavelength selectivity from 1112, 1116 and 1123 nm are discussed in detail.     

High-efficiency high-power QCW diode-side-pumped zigzag Nd:YAG ceramic slab laser

A high-efficiency high-power diode-side-pumped quasi-continuous wave (QCW) Nd:YAG ceramic slab laser using zigzag optical path was demonstrated. With an integrating sphere technique, the scattering and absorption coefficient of the ceramic slab were measured to be 0.0024 and 0.0016 cm^?1 at 1,064 nm, respectively. Under a pump power of 6.69 kW, an average output power of 2.44 kW at 1,064 nm with a repetition rate of 400 Hz was achieved, corresponding to an optical-to-optical efficiency of 36.5 %. As far as we know, this is the highest conversion efficiency reported for QCW side-pumped single slab Nd:YAG ceramic laser.     

Temperature characteristics of small signal gain for Nd/Cr:YAG ceramic lasers

Thermal dependence on the small signal gain of Nd/Cr:YAG (yttrium aluminum garnet) ceramics was observed experimentally. Usually, Nd:YAG crystal and ceramics have remarkable gain reduction when optical pumping is performed and the temperature of the laser media is upped to 373 K. A CW laser light generated in a 1064 nm Nd:YAG laser oscillator was amplified by Nd/Cr:YAG ceramic amplifier, and the output power was measured at non-saturation level. Laser small signal gain of the ceramic disk was kept to 470 K. This property was remarkably different from one of Nd:YAG crystals or ceramics. The peak shift of the fluorescence was observed experimentally when the temperature is high.     

Dual-polarization electro-optical Q-switched ceramic laser

A dual-polarization electro-optical Q-switched Nd:YAG ceramic laser was studied. By selecting the appropriate size of calcite crystals, the dual-polarization Q-switched pulse was achieved by characteristics of calcite crystal. Experimental results show that compared with the traditional single-polarization electro-optical Q-switched laser, insertion loss is reduced, dynamic to static ratio is greatly improved, thermally induced birefringence of electro-optical Q-switched Nd:YAG ceramic laser is effective compensated. The output power of 19 W and the pulse width of 13 ns are obtained at the repetition rate of 1 kHz and pumped power of 144 W. The dynamic to static ratio is 71%. The results formed the basis for the further development of the high power and high efficiency ceramic red laser.     

Diode-pumped passively Q-switched Nd:LuVO4 laser at 916 nm

We demonstrate a passively Q-switched Nd:LuVO₄ laser at 916 nm by using a Nd, Cr:YAG crystal as the saturable absorber. As we know, it is the first time to realize the laser with a simple linear resonator. When the incident pump power increased from 14.6 W to 23.7 W, the pulse width of the Q-switched laser decreased from 24 ns to 21 ns. The pulse width was insensitive to the incident pump power in the experiment. The average output power of 288 mW with repetition rate of 39 kHz was obtained at an incident pump power of 22.5 W, with the optical-to-optical efficiency and slope efficiency 1.3% and 3.6%, respectively.     

Highly efficient diode side-pumped Nd:YAG ceramic laser with 210 W output power

We developed a highly efficient diode side-pumped Nd:YAG ceramic laser with a diffusive reflector as an optical pump cavity. A maximum output power of 211.6 W was obtained with an optical-to-optical conversion efficiency of 48.7%. This corresponds to the highest conversion efficiency in the side-pumped ceramic rod. Thermal effects of the Nd:YAG ceramic rod were analyzed in detail through the measurements of laser output powers and beam profiles near the critically unstable region. A M² beam quality factor of 18.7 was obtained at the maximum laser output power.     

Nd:YAG陶瓷与单晶4F3/2–4I13/2跃迁的弱谱线多波长激光性能对比

报道了基于半导体激光端面抽运Nd:YAG的⁴F_3/2–⁴I_13/2 跃迁的弱谱线多波长激光输出. 实验对比了透明陶瓷与单晶材料的激光输出特性, 表明透明陶瓷和单晶材料荧光谱强度的略微差异, 导致了多波长输出时相同两个波长之间的激光强度比在两种材料中的差异. 基于两种耦合输出镜片, 激光阈值都在2 W左右. 在13.5 W的抽运功率下, 基于Nd:YAG透明陶瓷获得了输出功率4.05 W、强度比1 :2的1338与1356 nm双波长激光和输出功率3.65 W、强度比13 : 1的1356与1414 nm 双波长激光, 斜率效率分别达33.9% 和31.9%.     

678 nm RTP electro-optical Q-switched ceramic laser

The RTP electro-optical Q-switched ceramic laser at the wavelength of 678 nm with narrow pulse width is studied. We used the laser diode arrays side-pumped Nd:YAG ceramic crystal with 1.1 at% Nd doping and dimensions of Φ3 mm × 50 mm, designed folding cavity parameters, and discussed the variation of the beam radius in the ceramic crystal and frequency doubling crystal with the thermal focal length of ceramic crystal or KTP crystal. By using double RTP crystals as electro-optic Q-switch and KTP crystal type II phase matching for intracavity frequency-doubling, a narrow pulse width electro-optical Q-switched Nd:YAG ceramic laser was obtained. The output energy of 0.9 mJ and the pulse width of 41.6 ns at 678 nm are obtained at the repetition rate of 1000 Hz and pumped power of 144 W. The results formed the basis for the further development of the high power and high efficiency ceramic red laser.     

Diode-pumped passively Q-switched yellow laser with SrWO4 Raman crystal and ceramic Nd:YAG gain medium

A diode-pumped passively Q-switched Nd:YAG/SrWO₄/KTP yellow laser is presented for the first time. As high as 1.02 W average output power was obtained at a pump power of 14.0 W with a pulse repetition frequency of 21.9 kHz and the corresponding diode-to-yellow conversion efficiency was 7.29%. The highest pulse energy of 56.2 μJ was obtained at a pump power of 7.2 W.     

Simultaneous dual-wavelength Q-switched Nd:YAG laser operating at 1.06 μm and 946 nm

Considering the reabsorption loss of the quasi-three level system and the unsaturable loss of the saturable absorber, we obtained the operating condition of a diode-pumped simultaneous dual-wavelength Q-switched Nd:YAG laser operating at 1.06 μm and 946 nm. The dual-wavelength pulsed laser was realized successfully through adaptive coating design of the cavity mirrors. As much as 1.6 W total average output power of the dual-wavelength at 1.06 μm and 946 nm was achieved at the incident pump power of 14.2 W with an optical conversion efficiency of 11.3%.     

High efficiency,high power QCW diode-side-pumped Nd：YAG ceramic laser at 1064 nm based on domestic ceramic

A high efficiency, high power diode-side-pumped quasi continuous wave （QCW） Nd：YAG ceramic rod laser at 1064 nm based on the domestic transparent ceramic is reported. The average output power of 961 W is achieved with double ceramic rods by means of a symmetrical convex-convex cavity. The optical-to-optical conversion efficiency is 38.3% and the slope efficiency is 45.3%. To the best of our knowledge, this is the highest level of efficiency achieved for the domestic Nd：YAG ceramic rod laser.     

A 7.5?W quasi-continuous-wave sodium D2 laser generated from?single-pass sum-frequency generation in LBO crystal

We report a high-power, narrow linewidth and tunable quasi-continuous-wave (QCW) yellow laser system at 589.159?nm. The system is of a design employing single-pass sum-frequency generation (SFG) in a LBO crystal by mixing the 1064?nm with 1319?nm lines from a two diode-side-pumped Nd:YAG master oscillator-power amplifier (MOPA) laser system. With the pump power of 35?W at 1064?nm and 25?W at 1319?nm, a 7.5?W QCW output of the SFG yellow laser at 589.159?nm, which is the vacuum wavelength of a general sodium D₂ line, is obtained with a linewidth less than 0.7?GHz and a beam-quality factor M ²=1.2. The wavelength of the laser can be precisely step-tuned from 589.148 to 589.167?nm with an increment of 0.13?pm by means of a temperature-controlled etalon.     

Liquid-cooled ceramic Nd:YAG split-disk amplifier for high-average-power laser

A liquid-cooled ceramic Nd:YAG split-disk laser amplifier has been designed for a high-average-power laser system. The maximum average output power of 17.1 W (1.71 J at 10 Hz) and the beam size of far-field pattern with 1.5 times diffraction limit was obtained. The combination of liquid cooling for disk laser material and wavefront compensation with a phase conjugation mirror was demonstrated. The wavefront degradation by liquid cooling was observed and measured with Michelson interferometer and far-field patterns.     

High-power 3.8 μm tunable optical parametric oscillator based on PPMgO:CLN

The experimental results of a high-power 3.8 μm tunable laser are presented on a quasi-phase-matched single-resonated optical parametric oscillator in PPMgO:CLN pumped by a 1064 nm laser of an elliptical beam. Theoretical analyses of the PPMgO:CLN wavelength tuning are presented. The pump source was an acousto-optical Q-switched cw-diode-side-pumped Nd:YAG laser. The beam polarization matched the e-ee interaction in PPMgO:CLN. When the crystal was operated at 90 °C and the pump power was 150 W with a repetition rate of 10 kHz, average output power of 22.6 W at 3.86 μm and 63 W at 1.47 μm was obtained. The slope efficiency of the 3.86 μm laser with respect to the pump laser was 17.8%. The M² factors of the 3.86 μm laser were 1.74 and 4.86 in the parallel and perpendicular directions, respectively. The mid-IR wavelength tunability of 3.7-3.9 μm can be achieved by adjusting the temperature of a 29.2 μm period PPMgO:CLN crystal from 200 °C to 30 °C, which basically is accorded with the theoretic calculation.     

QCW diode-pumped 654 W AO Q-switched Nd:YAG rod oscillator-amplifier laser

A diode laser-pumped acoustic-optic Q-switched Nd:YAG master-oscillator power amplifier laser is presented. The laser is quasi continuously pumped at 1.1 kHz with a pulse width of 172 μs, and the ultrasonic frequency of the AO Q-switcher is set at a higher value (53 kHz). The master oscillator is designed as a thermally near-unstable-resonator, which presents an average output power of 48 W with a beam quality value of M² = 1.41 and a Q-switching pulse duration of 121 ns. The maximum average power of the MOPA system is 654 W, and the beam quality is M² = 6.