Electrodeposition of Au/nanosized diamond composite coatings

Ultra-dispersed diamond UDD particles were codeposited in gold matrix coatings from a sulphite electrolyte, changing bath load and key operating parameters. The influence of electrolyte pH, current density and bath load on current efficiency, particle co-deposition, surface morphology and microhardness of composite coatings was investigated. UDD incorporation is mainly affected by bath load; however, particle embedding is specifically sensitive to electrolyte pH and deposition current density. The maximum mass fraction of carbon in the coating, about 0.55%, is obtained by depositing from ultrasonically pre-treated electrolytes with UDD concentration 20 g l⁻¹, pH 9.5 and 3 mA cm⁻² . Au/UDD composites are characterised by an increased microhardness and improved wear resistance. When compared to pure gold coatings which are notoriously weak, Au/UDD electrodeposits from sulphite electrolytes represent a significant improvement. Presented at the 4th Baltic Conference on Electrochemistry, Greifswald, 13–16, 2005     

Empowering Zn Electrode Current Capability Along Interfacial Stability by Optimizing Intrinsic Safe Organic Electrolytes

Metallic Zn is one of the most promising anodes, but its practical application has been hindered by dendritic growth and serious interfacial reactions in conventional electrolytes. Herein, ionic liquids are adopted to prepare intrinsically safe electrolytes via combining with TEP or TMP solvents. With this synergy effect, the blends of TEP/TMP with an IL fraction of ≈25 wt% are found to be promising electrolytes, with ionic conductivities comparable to those of standard phosphate-based electrolytes while electrochemical stabilities are considerably improved; over 1000 h at 2.0 mA cm⁻² and ≈350 h at 5.0 mA cm⁻² with a large areal capacity of 10 mAh cm⁻². The use of functionalized IL turns out to be a key factor in enhancing the Zn²⁺ transport due to the interaction of Zn²⁺ ions with IL-zincophilic sites resulting in reduced interfacial resistance between the electrodes and electrolyte upon cycling leading to spongy-like highly porous, homogeneous, and dendrite-free zinc as an anode material.     

Electrochemical properties of liquid electrolyte added quasi-solid state TiO2 dye-sensitized solar cells

In this study a process has been introduced to replace traditional liquid or solid electrolyte coatings on dye-sensitized photoelectrode in solar cells. This process has more efficient diffusion of electrolyte, hence higher sensitivity. Better interfacial contact between polymer electrolyte and TiO₂ photoelectrode had improved electrochemical response and ionic conductivity of cell. Conductivity of this electrode was 9.33 × 10⁻³ S cm⁻¹ (at room temperature), which is much higher than the using traditional process for addition of electrolytes. It has 0.68 V open-circuit voltage and 3.19 mA cm⁻² short-circuit current density. Energy conversion efficiency of this cell was about 37% higher than the cell developed with traditional processes under constant light intensity (45 mW cm⁻²).     

Comparison of characteristics of solid oxide fuel cells with YSZ and CGO film solid electrolytes formed using magnetron sputtering technique

The work describes the methods of manufacturing single cells of solid oxide fuel cell (SOFC) with thin–film YSZ and CGO electrolytes and also with the bilayer YSZ/CGO electrolyte. Formation of YSZ and CGO films on the supporting NiO–YSZ anode of SOFC was carried out using the combined electron–ionic–plasma deposition technique. The microstructure and phase composition of the formed coatings are studied and also comparative analysis of electrochemical characteristics of single fuel cells with different electrolytes is performed. It is shown that the maximum power density of 1.35 W/cm² at the temperature of 800°C is obtained for the cell with bilayer YSZ/CGO electrolyte. However, the highest performance at lower working temperatures (650–700°C) is characteristic for the fuel cell with single–layer CGO electrolyte; its power density is 600–650 mW/cm².     

The effect of water on the anodic dissolution of aluminum in non-aqueous electrolytes

The influence of water concentration on the electrochemical behavior of Al anodes in Al/active-non-aqueous electrolytes is investigated. Normally passive, Al exhibits facile electrochemical oxidation in both AlCl₃/γ-butyrolactone (AlCl₃/BLA) and (C₂H₅)₄NCl acetonitrile (TEAC/ACN) electrolytes. However, in these two electrolytes, the influence of water on Al oxidation shows opposite effects. Incremental increase from 0 to 1.5 M H₂O (0 to 3% water by volume) hinders Al oxidation in 1 M AlCl₃/BLA, increasing polarization loss from 100 to 400 mV cm² mA⁻¹. Yet in 0.3 M TEAC/ACN, Al is passive in the absence of water, exhibiting currents only in the μA cm⁻² domain, equivalent to oxidative polarization losses of over 1000 mV cm² mA⁻¹. This polarization loss is alleviated by water addition, and decreases from 20 to 7 mV cm² mA⁻¹ as water is increased from 0.3 to 1.5 M. FT-IR spectroscopy, linear voltammetry, galvanostatic reduction, surface microscopy and electrolytic conductivity measurements were conducted to probe competing water activation or water passivation effects on organic-phase Al electrochemistry.     

Ni-Al layered double hydroxides electrodeposition from a chloride solution

Ni-Al LDHs was electrodeposited from a NiCl₂-AlCl₃ solution. In order to analyze the electrodeposition process, electrolytes with initial Al content range of 0–20% were used. With increasing Al content in the sample, the preferred orientations of (0 0 3) and (0 0 6), increased crystallinity, and decreased interlayer spacing were observed from the XRD results. A dissolution–recrystallization of (0 0 3) plane was detected among the Ni-Al LDHs from the strongly alkaline solution soaking results, which was found to be conducted easily in high Al-containing samples. The pH of the Al-containing electrolyte was much lower than that of pure NiCl₂ solution because lower pH was needed to start a precipitation reaction in the AlCl₃-NiCl₂ solution. The electrodeposition yield and current efficiency were found to decrease obviously in the electrolytes with initial Al content higher than 10%, which was attributed to the increasing Al content in the sample and diffusion of the complex ions. The electrodeposition pattern was in-situ in the electrolyte initially containing 10% Al, then, it developed toward and off in-situ in electrolytes initially containing 0–10% and 10–20% Al.     

Complex Formation in Electrolyte Solutions in the Course of Plating Protective Coatings on Titanium

Conditions for complex formation in aqueous electrolyte solutions containing salts of aluminum and hydroxy carboxylic acids were studied by ^{2 7}Al and ^{1 9}F NMR spectroscopy. The formation of complex anions in the electrolytes at various pH and their discharge on the anode under conditions of a microplasma process allowed preparation of surface layers containing -Al₂O₃ on VT1-0 titanium. The interrelation between the composition and properties of the coatings was studied.     

Evaluating the electrochemical properties of PEO‐based nanofibrous electrolytes incorporated with TiO2 nanofiller applicable in lithium‐ion batteries

In the present work, nanofibrous composite polymer electrolytes consist of polyethylene oxide (PEO), ethylene carbonate (EC), propylene carbonate (PC), lithium perchlorate (LiClO₄), and titanium dioxide (TiO₂) were designed using response surface method (RSM) and synthesized via an electrospinning process. Morphological properties of the as‐prepared electrolytes were studied using SEM. FTIR spectroscopy was conducted to investigate the interaction between the components of the composites. The highest room temperature ionic conductivity of 0.085 mS.cm^?1 was obtained with incorporation of 0.175 wt. % TiO₂ filler into the plasticized nanofibrous electrolyte by EC. Moreover, the optimum structure was compared with a film polymeric electrolyte prepared using a film casting method. Despite more amorphous structure of the film electrolyte, the nanofibrous electrolyte showed superior ion conductivity possibly due to the highly porous structure of the nanofibrous membranes. Furthermore, the mechanical properties illustrated slight deterioration with incorporation of the TiO₂ nanoparticles into the electrospun electrolytes. This investigation indicated the great potential of the electrospun structures as all‐solid‐state polymeric electrolytes applicable in lithium ion batteries.     

A novel composite polymer electrolyte containing room-temperature ionic liquids and heteropolyacids for dye-sensitized solar cells

A novel composite polymeric gel comprising room-temperature ionic liquids (1-butyl-3-methyl-imidazolium-hexafluorophosphate, BMImPF₆) and heteropolyacids (phosphotungstic acid, PWA) in poly(2-hydroxyethyl methacrylate) matrix was successfully prepared and employed as a quasi-solid state electrolyte in dye-sensitized solar cells (DSSCs). These composite polymer electrolytes offered specific benefits over the ionic liquids and heteropolyacids, which effectively enhanced the ionic conductivity of the composite polymer electrolyte. Unsealed devices employing the composite polymer electrolyte with the 3% content of PWA achieved the solar to electrical energy conversion efficiency of 1.68% under irradiation of 50 mW cm⁻² light intensity, increasing by a factor of more than three compared to a DSSC with the blank BMImPF₆-based polymer electrolyte without PWA. It is expected that these composite polymer electrolytes are an attractive alternative to previously reported hole transporting materials for the fabrication of the long-term stable quasi-solid state or solid state DSSCs.     

Electrolyte using blend salts of LiTFSI and LLZO for long-term high-safety lithium ion battery

It is crucial to obtain a reliable electrolyte system that is used for replacing thermally unstable and the moisture sensitive LiPF₆ salt in liquid electrolytes for developing excellent cycle stability lithium ion batteries with high safety. In this work, a kind of hybrid electrolytes, adding Ga–Bi co-doped Li₇La₃Zr₂O₁₂ (LLZO) into LiTFSI based commercial electrolyte, was successfully prepared. The results shows that adding Ga–Bi co-doped LLZO ceramic particles is benefit for enhancing conductivity of LiTFSI based commercial electrolyte, which is 3.14 mS cm⁻¹ from 3.02 mS cm⁻¹. Furthermore, the LiFePO₄| |Li cell assembling with LiTFSI based electrolyte with Ga–Bi co-doped LLZO ceramic particles shows good cycle performance and coulomb efficiency (100% except for the initial cycle value of 88%) due to a passivation multi-element film formed for preventing severe corrosion to the Al foil. The battery delivered a high first cycle discharge capacity of 144.2 mAh g⁻¹ (85% of theoretical LiFePO₄.) and a maximum value of 152.6 mAh g⁻¹ after the 69th cycle. After the 300 stable cycle, the capacity of 130.8 mAh g⁻¹ (85.7% of the maximum data) remained.     

阴离子为羧酸根和芳环共轭的离子液体在染料敏化太阳能电池中的应用

提出了利用p-π共轭效应设计离子液体的方法, p-π共轭效应可以有效分散阴离子的负电荷, 降低离子液体中阴阳离子之间的库仑引力, 以得到低粘度的离子液体. 所设计的离子液体为1-乙基-3-甲基咪唑苯甲酸(EMIB)和1-乙基-3-甲基咪唑异烟酸(EMIIN) (它们的阴离子中羧酸根和芳环为p-π共轭结构), 这两种离子液体都达到了较低的粘度(EMIB为42 mPa·s, EMIIN为27 mPa·s). 进一步将这两种离子液体做成电解质, 应用在染料敏化太阳能电池中, 通过优化电解质的组成, EMIB基电解质达到了1.43 mS·cm^-1的电导率和1.45×10^-7cm²·s^-1的I₃^?的扩散系数, 而EMIIN基电解质的电导率和I₃^?扩散系数分别为1.63 mS·cm^-1和2.01×10^-7 cm²·s^-1,后者电导性能的提高主要和EMIIN粘度较低有关系. 进一步将这两种电解质组装成电池, 在300 W·m^-2的光强下测得EMIB基电池和EMIIN基电池的效率分别为2.85%和4.30%.     

Cold-Resistant Nitrogen/Sulfur Dual-Doped Graphene Fiber Supercapacitors with Solar–Thermal Energy Conversion Effect

Although graphene fiber-based supercapacitors are promising for wearable electronic devices, the low energy density of electrodes and poor cold resistance of aqueous electrolytes limit their wide application in cold environments. Herein, porous nitrogen/sulfur dual-doped graphene fibers (NS-GFs) are synthesized by hydrothermal self-assembly followed by thermal annealing, exhibiting an excellent capacitive performance of 401 F cm⁻³ at 400 mA cm⁻³ because of the synergistic effect of heteroatom dual-doping. The assembled symmetric all-solid-state supercapacitor with polyvinyl alcohol/H₂SO₄/graphene oxide gel electrolyte exhibits a high capacitance of 221 F cm⁻³ and a high energy density of 7.7 mWh cm⁻³ at 80 mA cm⁻³. Interestingly, solar–thermal energy conversion of the electrolyte with 0.1 wt % graphene oxide extends the operating temperature range of the supercapacitor to 0 °C. Furthermore, the photocatalysis effect of the dual-doped heteroatoms increases the capacitance of NS-GFs. At an ambient temperature of 0 °C, the capacitance increases from 0 to 182 F cm⁻³ under 1 sun irradiation because of the excellent solar light absorption and efficient solar–thermal energy conversion of graphene oxide, preventing the aqueous electrolyte from freezing. The flexible supercapacitor exhibits a long cycle life, good bending resistance, reliable scalability, and ability to power visual electronics, showing great potential for outdoor electronics in cold environments.     

Synergistic Modulation of In-Situ Hybrid Interface Construction and pH Buffering Enabled Ultra-Stable Zinc Anode at High Current Density and Areal Capacity

In aqueous electrolytes, the uncontrollable interfacial evolution caused by a series of factors such as pH variation and unregulated Zn²⁺ diffusion would usually result in the rapid failure of metallic Zn anode. Considering the high correlation among various triggers that induce the anode deterioration, a synergistic modulation strategy based on electrolyte modification is developed. Benefitting from the unique pH buffer mechanism of the electrolyte additive and its capability to in situ construct a zincophilic solid interface, this synergistic effect can comprehensively manage the thermodynamic and kinetic properties of Zn anode by inhibiting the pH variation and parasitic side reactions, accelerating de-solvation of hydrated Zn²⁺, and regulating the diffusion behavior of Zn²⁺ to realize uniform Zn deposition. Thus, the modified Zn anode can achieve an impressive lifespan at ultra-high current density and areal capacity, operating stably for 609 and 209 hours at 20 mA cm⁻², 20 mAh cm⁻² and 40 mA cm⁻², 20 mAh cm⁻², respectively. Based on this exceptional performance, high loading Zn||NH₄V₄O₁₀ batteries can achieve excellent cycle stability and rate performance. Compared with those previously reported single pH buffer strategies, the synergistic modulation concept is expected to provide a new approach for highly stable Zn anode in aqueous zinc-ion batteries.     

Effect of solvents on properties of polymer gel-electrolyte based on polyester diacrylate

New polymer gel electrolytes based on polyester diacrylates and LiClO₄ salt solutions in organic solvents are developed for lithium ion and lithium polymer batteries with a high ionic conductivity up to 2.7 × 10^?3 Ohm^?1cm^?1 at the room temperature. To choose the optimum liquid electrolyte composition, the dependence is studied of physico-chemical parameters of new gel electrolytes on the composition of the mixture of aprotic organic solvents: ethylene carbonate, propylene carbonate, and λ-butyrolacton. The bulk conductivity of gel electrolytes and exchange currents at the gel electrolyte/Li interface are studied using the electrochemical impedance method in symmetrical cells with two Li electrodes. The glass transition temperature and gel homogeneity are determined using the method of differential scanning calorimetry. It is found that the optimum mixture is that of propylene carbonate and λ-butyrolacton, in which a homogeneous polymer gel is formed in a wide temperature range of ?150 to +50°C.     

Two-Plateau Li-Se Chemistry for High Volumetric Capacity Se Cathodes

For Li-Se batteries, ether- and carbonate-based electrolytes are commonly used. However, because of the “shuttle effect” of the highly dissoluble long-chain lithium polyselenides (LPSes, Li₂Se_n, 4≤n≤8) in the ether electrolytes and the sluggish one-step solid-solid conversion between Se and Li₂Se in the carbonate electrolytes, a large amount of porous carbon (>40 wt % in the electrode) is always needed for the Se cathodes, which seriously counteracts the advantage of Se electrodes in terms of volumetric capacity. Herein an acetonitrile-based electrolyte is introduced for the Li-Se system, and a two-plateau conversion mechanism is proposed. This new Li-Se chemistry not only avoids the shuttle effect but also facilitates the conversion between Se and Li₂Se, enabling an efficient Se cathode with high Se utilization (97 %) and enhanced Coulombic efficiency. Moreover, with such a designed electrolyte, a highly compact Se electrode (2.35 g_Se cm⁻³) with a record-breaking Se content (80 wt %) and high Se loading (8 mg cm⁻²) is demonstrated to have a superhigh volumetric energy density of up to 2502 Wh L⁻¹, surpassing that of LiCoO₂.     

The conducting polymer electrolyte based on polypyrrole-polyvinyl alcohol and its application in low-cost quasi-solid-state dye-sensitized solar cells

The effect of polypyrrole (PPy) on the polyvinyl alcohol (PVA)-potassium iodide (KI)-iodine (I₂) polymer electrolytes has been investigated and optimized to use in a dye-sensitized solar cell (DSSC). The different weight ratios of PVA: PPy (93: 2, 91: 4, 89: 6, 87: 8, and 85: 10 wt%) polymer electrolytes (PE) were prepared by solution casting. Structural, complex formation and surface roughness of the prepared electrolytes was confirmed by X-ray diffraction, FTIR, and atomic force microscopy (AFM) respectively. Conductivity plots of all polymer films showed increasing trend with temperature and concentration of PPy. The activation energy of the optimized system found to be 0.871 kJ mol^?1. UV-visible spectrum was adopted to characterize the absorption spectra of the material revealed that increase in the absorbance with increasing PPy content and shifting the absorbance maximum towards lower energy. The indirect band gap decreased from 3.78 to 2.14 eV and direct band gap decreased from 3.88 to 2.71 eV. The EIS analyses revealed the lower charge transfer resistance of 3.029 Ω cm² at the interface between CE and PE. The excellent performance was observed in the fabricated DSSCs using PVA (85%)/PPy (10%)/KI (5%)/I₂ polymer electrolyte with a short-circuit current density of 11.071 mA cm^?2, open-circuit voltage of 0.644 V, fill factor of 0.575, and photovoltaic conversion efficiency of 4.09% under the light intensity of 100 mW cm^?2. Hence, the PPy content in polymer electrolyte influences the remarkable performance of low-cost DSSC.     

Boron-incorporated Sulfonated polysulfone/polyphosphoric acid electrolytes for supercapacitor application

In the present work, boron-doped multicomponent gel polymer electrolytes composed of host polymer, sulfonated polysulfone (SPSU) and the additives; ionic liquid, 1-ethyl-3-methyl-imidazolium tetrafluoroborate (IL), H₃BO₃, polyphosphoric acid (PPA) were prepared. Fourier transform infrared spectroscopy (FT-IR), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) techniques were used to characterize the sulfonated polysulfone-based electrolytes. Ion conductivity of these gel electrolytes were studied by dielectric impedance analyzer within the temperature from ?20 to 100°C. The ionic conductivity of the SPSU-5IL-1PPA and SPSU-5IL-1H₃BO₃-1PPA were measured as 4.8 × 10^?3 and 9 × 10^?4 S cm^?1, respectively. Supercapacitor having activated carbon-based composite electrode and electrolyte was constructed with the configuration: Al/C/electrolyte/C/Al. The electrochemical properties and ion transfer characteristics of the supercapacitor were investigated by the cyclic voltammetry (CV). Galvanostatic charge—discharge experiments exhibited good electrochemical reversibility and produced a specific capacitance value of 120 F g^?1 at 1 A g^?1. The symmetric supercapacitor system was retained almost 85% of its initial activity after 1000 cycle.     

Boosting Zn Anode Utilization by Trace Iodine Ions in Organic-Water Hybrid Electrolytes through Formation of Anion-rich Adsorbing Layers

Aqueous Zn batteries are attracting extensive attentions, but their application is still hindered by H₂O-induced Zn-corrosion and hydrogen evolution reactions. Addition of organic solvents into aqueous electrolytes to limit the H₂O activity is a promising solution, but at the cost of greatly reduced Zn anode kinetics. Here we propose a simple strategy for this challenge by adding 50 mM iodine ions into an organic-water (1,2-dimethoxyethane (DME)+water) hybrid electrolyte, which enables the electrolyte simultaneously owns the advantages of low H₂O activity and accelerated Zn kinetics. We demonstrate that the DME breaks the H₂O hydrogen-bond network and exclude H₂O from Zn²⁺ solvation shell. And the I⁻ is firmly adsorbed on the Zn anode, reducing the Zn²⁺ de-solvation barrier from 74.33 kJ mol⁻¹ to 32.26 kJ mol⁻¹ and inducing homogeneous nucleation behavior. With such electrolyte, the Zn//Zn symmetric cell exhibits a record high cycling lifetime (14.5 months) and achieves high Zn anode utilization (75.5 %). In particular, the Zn//VS₂@SS full cell with the optimized electrolyte stably cycles for 170 cycles at a low N : P ratio (3.64). Even with the cathode mass-loading of 16.7 mg cm⁻², the full cell maintains the areal capacity of 0.96 mAh cm⁻² after 1600 cycles.     

Electrodeposition kinetics of tin—antimony alloy from sulfate electrolyte with organic additives

Kinetics of the Sn-Sb alloy electrodeposition from sulfate electrolytes containing organic additives (syntanol DS-10, Formalin, 1,4-butynediol) is studied by the faradaic impedance method. Bright Sn-Sb alloy coatings are plated in this electrolyte at i_c = 0.5-5 A/dm². With increasing i_c, the Sb content in the alloy decreases from 14 to 6.6 wt %     

Aluminum electrodeposition from a non-aqueous electrolyte—a combined computational and experimental study

Electrodeposition of aluminum (Al) from an organic non-aqueous electrolyte of ethylbenzene containing aluminum bromide is demonstrated. It is offered as a simple method for the preparation of Al coatings. This work employs distinct electrochemical techniques and explores the effects of the experimental parameters on the kinetics of the process and the quality of the final coatings. The process presented here enables deposition of pure and crystalline Al at room temperature and facilitates the production of uniform Al coatings on various metallic substrates. Morphological studies establish that the growth of Al deposits follows an island mode, and thus, the most noteworthy effect of the substrate over the morphology of the deposits originates from its impact over the nucleation stage, and the density of islands. This study is complemented by theoretical modeling for the adsorption of Al atoms at the different surfaces. Corrosion evaluation determines the dissolution mechanisms of each of the studied substrates in the examined electrolyte. These findings further corroborate the claim that this electrolyte enables the reversible electrodeposition of Al.