All-Solid-State Nd:YAG Laser Operating at 1064nm and 1319nm under 885nm Thermally Boosted Pumping

We report a high-effciency Nd：YAG laser operating at 1064 nm and 1319nm, respectively, thermally boosted pumped by an all-solid-state Q-switched Ti：sapphire laser at 885 nm. The maximum outputs of 825.4 m W and 459.4mW, at 1064nm and 1319nm respectively, are obtained in a 8-ram-thick 1.1 at.% Nd：YAG crystal with 2.1 W of incident pump power at 885nm, leading to a high slope efficiency with respect to the absorbed pump power of 68.5% and 42.0%. Comparative results obtained by the traditional pumping at 808nm are presented, showing that the slope efficiency and the threshold with respect to the absorbed pump power at 1064nm under the 885nm pumping are 12.2% higher and 7.3% lower than those of 808rim pumping. At 1319nm, the slope efficiency and the threshold with respect to the absorbed pump power under 885nm pumping are 9.9% higher and 3.5% lower than those of 808 nm pumping. The heat generation operating at 1064 nm and 1319 nm is reduced by 19.8% and 11.1%, respectively.     

Comparison of Nd:YAG Ceramic Laser Pumped at 885nm and 808nm

Laser performance of 1064 nm domestic Nd：YAG ceramic lasers for 885 nm direct pumping and 808 nm traditional pumping are compared. Higher slope efficiency of 34% and maximum output power of 16.5 W are obtained for the 885nm pump with a 6ram length 1 at.% Nd：YAG ceramic. The advantages for 885nm direct pumping are discussed in detail. This pumping scheme for highly doping a Nd：YAG ceramic laser is considered as an available way to generate high power and good beam quality simultaneously.     

1064 nm Nd:YAG laser intracavity pumped at 946 nm

We present for the first time a Nd:YAG laser emitting at 1064 nm intracavity pumped by a 946 nm diode-pumped Nd:YAG laser. A 885 nm laser diode is used to pump the first Nd:YAG crystal emitting at 946 nm, and the second Nd:YAG laser emitting at 1064 nm intracavity pumped at 946 nm. We achieved an output power of 7.97 W at 1064 nm for an absorbed pump power at 946 nm of 9.55 W, corresponding to an optical efficiency of 83.4%. The beam quality M² quality factor is about 1.1 at the maximum output power.     

Tunable sub-100 femtosecond dye-laser pulses generated with a nanosecond pulsed pumping

Subpicosecond pulses at a fixed wavelength produced with a low-Q cavity dye laser pumped by a single, nanosecond laser (Q-switched Nd:YAG) are converted into tunable high-power sub-100 femtosecond pulses by generation, spectral selection, amplification and compression of a supercontinuum. The tunable, chirped, high-energy pulses obtained are compressed with a prism pair. Energies up to 50 J in sub-100 fs pulses were obtained in the 540 to 650 nm range using 40 mJ of the Nd: YAG-laser pumping pulses at 532 nm. The whole sub-100 fs system including the low-Q dye laser uses only one Nd:YAG laser as a pump source.     

A 4.8-W M^2 = 4.6 Continuous-Wave Intracavity Sum-Frequency Diode-Pumped Solid-State Yellow Laser

A yellow continuous wave with beam quality M^2= 4.6 and output power of 4.8 W at 589nm is generated by intracavity sum-frequency mixing of 1064 nm and 1319 nm radiations of a Nd：YAG laser. To achieve high beam quality at high power, thermally near-unstable flat-flat resonators with two-rod birefringence compensation are designed to obtain the large fundamental mode size inside the Nd：YAG rods and the same beam width inside the KTP crystal. The optimal intracavity power ratio of both 1064nm and 1319nm beams is also considered. The output power fluctuation of the yellow laser remains less than 5% in four hours.     

Efficient generation of tunable VUV laser radiation below 205 nm by SFM in BBO

Design and performance characteristics of a tunable dye laser system for sum frequency mixing (SFM) in a BBO crystal are presented. The system is composed of two tunable pulsed dye lasers pumped synchronously by the second harmonic of a commercial Nd:YAG laser. The radiation produced by the first dye laser is frequency doubled by second-harmonic generation (SHG) in KDP and subsequently mixed by SFM in BBO with the light of the second dye laser. The interest was focussed on generation of tunable laser radiation below 205 nm with high output power and long-time wavelength stability. High conversion efficiencies enable output energies of 100 J (20 kW) at 196 nm using only moderate Nd:YAG pump energies of 67 mJ. Altogether, a laser system with very good specifications for analytical application in the near VUV spectral region is reported.     

Simultaneous Generation of Multi-Wavelength Laser from Nd:YAG Crystals in a Cruciform Cavity

A cruciform cavity is presented for multi-wavelength laser generation. On the basis of considering the optimal power ratio and good spatial overlap of the two fundamental beams, the maximum output power of 589 nm laser reaches 3.5 W when the pumping power of Nd：YAG A and Nd：YAG B are 311.5 W and 261.8 W, respectively. At the same time, the other wavelength lasers are also obtained with the output power distribution of 2.5 W at 66Onto, 15 W at 532nm, lOOmW at 1319nm and 240mW at 1064nm. The corresponding beam quality factors are M^2 x = 4.93, M^2 y = 5.01 at 589nm, M^2z = 4.51, M^2 y = 4.85 at 660hm, and M^2 x = 4.12, M^2 y = 3.96 at 532nm, respectively. The instabilities of the three visible lights are measured, which are also less than 2% within three hours.     

1064 nm和532 nm纳秒激光同时辐照熔石英损伤规律的研究

利用Nd: YAG激光器研究基频(1064 nm)与倍频(532 nm)单独辐照和同时辐照下熔石英的损伤规律,对损伤几率进行了测试,获得损伤几率曲线与典型损伤形貌。研究结果表明:双波长同时辐照下的初始损伤阈值总是小于单波长辐照下的初始损伤阈值;基频光中加入定量倍频光后,熔石英对基频光的吸收效率提高;并且双波长同时辐照下,熔石英损伤密度增大;原因主要是熔石英表面缺陷对不同波长吸收机制的差异。     

A flashlamp-pumped 946 nm Nd:YAG laser

Generation of 946 nm radiation from a commercially available, flashlamp-pumped Nd:YAG laser was investigated. By suppression of the high-gain 1.064 m transition and with a specially designed cooling system, a stable emission at 946 nm was achieved in the temperature range 300–240 K. At a repetition rate of 10 Hz laser output powers of 100mW and 500 mW were obtained at room temperature and 240 K respectively. The temperature dependence of unsaturated gain, slope efficiency and pumping threshold were determined.S. Dimov is supported by a fellowship from the Alexander von Humboldt Foundation     

1064nm纳秒激光脉冲激发的外腔式PbWO4拉曼激光器

研究了外腔式PbWO4拉曼激光器在纳秒脉冲抽运下的输出特性。利用主动调Q的Nd:YAG激光器产生的脉冲宽度为31.4ns,最大输出能量为200mJ的1064nm激光作为抽运源。拉曼激光谐振腔采用的是平凹腔设计。测量了输出的拉曼光脉宽与抽运能量的关系,分析了输出的拉曼光脉冲波形图和光谱图,测量了输出的拉曼光脉冲能量与抽运能量的关系,计算了转换效率与抽运能量的关系。当注入抽运光能量达到42mJ时,得到了一阶斯托克斯光脉冲的最大能量和转换效率分别为10mJ和24%,获得外腔式PbWO4拉曼激光器的一阶斯托克斯光脉冲波长为1177.6nm,典型的一阶斯托克斯光脉冲脉宽为20ns。     

4-W and 23-ps pulses from a lamp-pumped Nd:YAG laser passively mode-locked by polarization switching in a KTP crystal

Passive mode-locking of a cw lamp-pumped Nd:YAG laser using nonlinear polarization switching in a type-II SHG crystal is reported. Light pulses with more than 5 W of average power and pulse duration shorter than 25 ps have been obtained at 1064 nm. Received: 29 January 1999 / Revised version: 24 March 1999 / Published online: 1 July 1999     

Q-switched Nd lasers pumped directly into the F3/2 emitting level

The influence of the direct pumping into the ⁴F_3/2 emitting level on the output characteristics of continuous-wave (CW) pumped, passively or actively (acoustooptic, AO) Q-switched Nd lasers is discussed. In case of passive Q-switching by Cr⁴⁺:YAG saturable absorber (SA) crystal, the change of pumping wavelength from 0.81 μm into the highly-absorbing ⁴F_5/2 level to 0.88 μm into the ⁴F_3/2 level of Nd does not modify the energy of the Q-switch pulse, but increases the pulse repetition rate and the laser average power for the same absorbed pump power. This is demonstrated with 0.81 and 0.88 μm CW laser diode-pumped Nd:YAG and Nd-vanadate lasers with average output power in the watt-level range at 1.06 μm. The effect is explained by the control of passive Q-switching by the intracavity photon flux that is influenced by the pump wavelength and by the initial transmission of the SA crystal. On the other hand, it is discussed and experimentally proved that due to the possibility to control externally the frequency of switching, in case of the AO Q-switched Nd laser the change of the pump wavelength from 0.81 to 0.88 μm increases the pulse energy for a fixed frequency, leading to a corresponding increase of the average laser power.     

High-power simultaneous dual-wavelength emission of an end-pumped Nd:YAG laser using the quasi-three-level and the four-level transition

An efficient continuous-wave (CW) simultaneous dual-wavelength lasing (SDWL) of an LD end-pumped Nd:YAG laser utilizing a quasi-three-level transition at 946 nm and a four-level transition at 1064 nm is reported. A theoretical model has been introduced to determine the threshold conditions for SDWL. The temperature distributions of a Nd:YAG crystal under different pump powers have been analyzed. In the experiments, a CW SDWL output power of 5.12 W at a temperature of 273 K has been achieved with a pump power of 17 W, giving a slope efficiency of 16.36%.     

Surface modifications of a titanium implant by a picosecond Nd:YAG laser operating at 1064 and 532 nm

Interaction of an Nd:YAG laser, operating at 1064 or 532 nm wavelength and pulse duration of 40 ps, with titanium implant was studied. Surface damage thresholds were estimated to 0.9 and 0.6 J/cm² at wavelengths 1064 and 532 nm, respectively. The titanium implant surface modification was studied by the laser beam of energy density of 4.0 and 23.8 J/cm² (at 1064 nm) and 13.6 J/cm² (at 532 nm). The energy absorbed from the Nd:YAG laser beam is partially converted to thermal energy, which generates a series of effects, such as melting, vaporization of the molten material, shock waves, etc. The following titanium/implant surface morphological changes were observed: (i) both laser wavelengths cause damage of the titanium in the central zone of the irradiated area, (ii) appearance of a hydrodynamic feature in the form of resolidified droplets of the material in the surrounding outer zone with the 1064 nm laser wavelength and (iii) appearance of wave-like microstructures with the 532 nm wavelength. Generally, both laser wavelengths and the corresponding laser energy densities can efficiently enhance the titanium/implant roughness. This implant roughness is expected to improve its bio-integration. The process of the laser interaction with titanium implant was accompanied by formation of plasma.     

Surface modifications of AISI 1045 steel created by high intensity 1064 and 532 nm picosecond Nd:YAG laser pulses

Interaction of Nd:YAG laser, operating at 1064 or 532 nm wavelength and a pulse duration of 40 ps, with AISI 1045 steel was studied. Surface damage thresholds were estimated to be 0.30 and 0.16 J/cm² at the wavelengths of 1064 and 532 nm, respectively. The steel surface modification was studied at the laser energy density of 10.3 J/cm² (at 1064 nm) and 5.4 J/cm² (at 532 nm). The energy absorbed from Nd:YAG laser beam is partially converted to thermal energy, which generates a series of effects, such as melting, vaporization of the molten material, shock waves, etc. The following AISI 1045 steel surface morphological changes and processes were observed: (i) both laser wavelengths cause damage of the steel in the central zone of irradiated area; (ii) appearance of a hydrodynamic feature in the form of resolidified droplets of the material in the surrounding outer zone with 1064 nm laser wavelength; (iii) appearance of periodic surface structures, at micro- and nano-level, with the 532 nm wavelength and, (iv) development of plasma in front of the target. Generally, interaction of laser beam with the AISI 1045 steel (at 1064 and 532 nm) results in a near-instantaneous creation of damage, meaning that large steel surfaces can be processed in short time.     

Passively Q-switched Nd:YAG pumped UV lasers at 280 and 374 nm

Pulsed UV lasers at the wavelengths of 374 and 280 nm are realized by cascaded second harmonic generation (SHG) and sum frequency generation (SFG) processes using a Nd:YAG laser at 1123 nm. The Nd:YAG laser is longitudinally pumped and passively Q-switched, and it has a high peak power of 3.2 kW. The UV peak powers at 280 and 374 nm are 100 and 310 W, with pulse lengths of 6 and 8 ns, respectively. Spectral broadening of 374 nm laser by stimulated Raman scattering is studied in single mode pure silica core UV fiber. Realizations of UV lasers enabling compact design at 280 and 374 nm wavelengths are demonstrated.     

Single-frequency 1.25 W monolithic lasers at 1123 nm

Experimental investigation ofd Nd:YAG monolithic nonplanar ring lasers operated at 1123 nm wavelength is presented. Stable single-frequency 1123 nm laser output has been obtained with successful suppression of the strong 1064 nm radiation. Single-frequency output power of 1.25 W is demonstrated with a pump power of 3.98 W at 808 nm, which gives a slope efficiency of 39%. The laser frequency tuning range is over 3 GHz, and the average tuning rate with temperature is -2.6 GHz/ degrees C. A strong iodine absorption line can be covered within the laser frequency tuning range.     

Nd:LuYAG混晶1123 nm被动调Q激光器

文章报道了一个二极管激光抽运的1123 nm被动调Q激光器. 激光晶体为混晶Nd:LuYAG, 饱和吸收体选为Cr⁴⁺:YAG晶体. 在连续运转情况下, 最高输出功率为2.77 W, 对应的光-光转换效率为29.53%. 调Q运转时, 在9.38 W吸收抽运功率下, 最高输出功率为0.94 W. 脉冲宽度整体在105 ns左右. 在最高吸收抽运功率下, 1123 nm激光的输出重复频率为9.40 kHz, 对应的单脉冲能量可达100 μJ, 高于目前报道的单晶Nd:YAG 1123 nm单脉冲能量, 证明其在能量存储方面较单晶Nd:YAG更具优势. 另外, 据我们所知, 这是关于混晶Nd:LuYAG 1123 nm输出的首次报道.     

An All-Solid-State Tunable Dual-Wavelength Ti：Sapphire Laser with Quasi-Continuous-Wave Outputs

A high power dual-wavelength Ti：sapphire laser system with wide turning range and high efficiency is described, which consists of two prism-dispersed resonators pumped by an a11-solid-state frequency-doubled Nd：YAG laser. Tunable dual-wavelength outputs, with one wavelength range from 750nm to 795nm and the other from 80Ohm to 850nm, have been demonstrated. With a pump power of 23 W at 532nm, a repetition rate of 6.5kHz and a pulse width of 67.6ns, the maximum dual-wavelength output power of 5.6 W at 785.3nm and 812.1 run, with a pulse width of 17.2ns and a line width of 2nm, has been achieved, leading to an optical-to-optical conversion efficiency of 24.4%.     

An 8.1 W diode pumped solid-state quasi-continuous-wave yellow laser at 589 nm by intracavity sum-frequency mixing generation

We report an L-shaped symmetrical co-folding-arm plane-plane diode pumped solid-state yellow laser at 589 nm by using intracavity sum-frequency mixing. By carefully designing the cavity and employing various techniques to optimize the laser’s specifications, a quasi-continuous-wave (QCW) free-oscillation yellow laser source, which has an average output power of 8.1 W, a beam quality factor of M² = 2.3, and a repetition rate of 1.1 kHz, is developed. The generation of yellow laser at 589 nm is achieved by intracavity sum-frequency mixing between the laser lines at 1319 nm and 1064 nm of an Nd:YAG laser in a KTP crystal. To the best of our knowledge, the 8.1 W output at 589 nm is higher than any other diode pumped solid-state yellow laser generated by intracavity sum-frequency generation so far.