Determination of bismuth oxide in and on high-purity bismuth

Bismuth is dissolved in mercury on shaking with ammonium nitrate solution in a nitrogen atmosphere; bismuth oxide is insoluble and so can be separated by flotation and dissolved in nitric acid for spectrophotometric determination as tetraiodobismuthate(III). The method is applied to various bismuth samples containing about 0.01% Bi₂O₃, the relative standard deviation being 7–11%.     

Use of a bismuth ion-selective electrode for investigation of bismuth complexes of citric and malic acids

A bismuth ion-selective electrode has been used to determine the nature and stability of the complexes formed by bismuth with citric acid and malic acid, by measurement of the response of the electrode to different total bismuth concentrations at various combinations of pH and total ligand concentration. The values found were beta(2) = 3 x 10(13) for Bi(Cit)(2)(3-) and beta(3) = 8 x 10(9) for Bi(Mal)(2)(3-).     

Formation of the bismuth thiolate compound layer on bismuth surface

The structure and composition of thiolate multilayers formed at bismuth monocrystal electrodes from solutions of 1-octadecanethiol and 1-decanethiol in ethanol at open circuit potential are characterized by cyclic voltammetry, electrochemical impedance and infrared reflectance spectroscopy, optical microscopy and AFM methods. Analysis of results demonstrates that after holding of Bi(h k l) electrodes during some hours in solution of thiol in ethanol bismuth is covered with a thick porous layer of bismuth thiolate compound. For the verification of formed thiolate layers the new compounds tris(1-octadecylthio)bismuthine and tris(1-decylthio)bismuthine were also synthesised from bismuth(III)oxide and thiol in hexane solution and a similarity of properties with the bismuth thiolate compounds, formed at the bismuth electrode surface, has been demonstrated.     

Identification, isolation, and characterization of cysteinate and thiolactate complexes of bismuth

Although bismuth compounds have been used in medicine for over 200 years, chemical characterization of complexes involving biological molecules is minimal and mechanisms of bioactivity are ill-defined. The thiophilic nature of bismuth implicates sulfur centers as likely sites for interaction, and we have exploited this feature to identify, isolate, and characterize complexes of bismuth with thiolate-carboxylate bifunctional ligands including the amino acid l-cysteine. The solid-state structures of potassium dichloro(thiopropionato)bismuth (K[1d]), dimethylaminoethanethiolato(thiopropionato)bismuth (4), and dinitrato(cysteinato)bismuthphenanthroline [5(phen)] are compared with data from electrospray ionization mass spectrometry (ESI-MS). ESI-MS is applied to reactions of BiCl(3) or Bi(NO(3))(3) with mercaptosuccinic, malic, and succinic acids to illustrate the general observation of 1:1 and 1:2 complexes.     

Determination of bismuth by selenious acid

Summary Bismuth is shown to be precipitated quantitatively as bismuth selenite by boiling an almost neutral solution of bismuth nitrate and excess selenious acid. The excess H₂SeO₃ is determined iodometrically by standard thiosulphate or arsenious oxide solution. Alternatively, the precipitated selenite may be dried at 105–110° C and weighed as Bi₂(SeO₃)₃.Sincere thanks of the authors are due to Prof. S. S. Joshi for research facilities and to Dr. G. S. Deshmukh for keen interest in the work.     

Hydrolysis of a basic bismuth nitrate--formation and stability of novel bismuth oxido clusters

The synthesis of the nanoscaled bismuth oxido clusters [Bi(38)O(45)(NO(3))(20)(DMSO)(28)](NO(3))(4)·4DMSO (1a) and [Bi(38)O(45)(OH)(2)(pTsO)(8)(NO(3))(12)(DMSO)(24)](NO(3))(2)·4DMSO·2H(2)O (2) starting from the basic bismuth nitrate [Bi(6)O(4)(OH)(4)](NO(3))(6)·H(2)O is reported herein. Single-crystal X-ray diffraction analysis, ESI mass spectrometry, thermogravimetric analysis, and molecular dynamics simulation were used to study the formation, structure, and stability of these large metal oxido clusters. Compounds 1a and 2 are based on a [Bi(38)O(45)](24+) core, which is structurally related to δ-Bi(2)O(3). Examination of the fragmentation pathways of 1a and 2 by infrared multi-photon dissociation (IRMPD) tandem MS experiments allows the identification of novel bismuth oxido cluster species in the gas phase.     

Fabrication of bismuth subcarbonate nanotube arrays from bismuth citrate

Bismuth subcarbonate ((BiO)2CO3) nanotubes with uniform diameters of about 3-5 nm were fabricated from bismuth citrate; these nanotubes exhibit antibacterial properties against Helicobacter pylori (50% inhibition at 10 microg mL(-1)), a bacterium causing peptic ulcers and gastritis.     

Electroanalysis of some nitro-compounds using bulk bismuth electrode

Nitro compounds were usually determined electrochemically using the mercury drop with DPP technique. An alternate way to toxic mercury is the increasing use of the bismuth electrode as thin film electrodeposited on glassy carbon or copper for example, or as bulk bismuth disc. In the present paper several nitrocompounds were investigated: mononitrophenols, dinitrophenol, nitrobenzoic acid, nitrobenzaldehyde and a well known pesticide, parathion, which has a nitro group in para position on a phenyl cycle. Bulk bismuth electrode was a disc (cross section of a rod of 5 mm diameter embedded in Teflon®) polished with silicon carbide disc (P2400) and sonicated to remove any abrasive particle. The supporting electrolyte was the acetic buffer (pH 4.7), which was found suitable for all these compounds. Using cathodic sweep differential pulse voltammetry, it was noticed that according to the position of the nitro group on the cycle, the peak potentials might range between ?300 to ?750 mV vs. SCE. Limits of detection (LOD) and limits of quantification (LOQ) were determined for each compound whose response for increasing concentration was linear in the ～3–50 µmol L^?1 whatever the considered molecule. Adsorptive differential pulse voltammetry was found very efficient to determine parathion, because this molecule adsorbs on bismuth at ?0.2 V vs. SCE. Bulk bismuth electrode was compared to the hanging mercury drop electrode and led to an identical behaviour.     

In situ transmission electron microscopy observation of the growth of bismuth oxide whiskers.

Growth of bismuth oxide (most probably Bi2O3) was observed in situ in a transmission electron microscope. Bi liquid particles were dispersed on the substrates of diamond or SiO2. Introduction of oxygen up to 5 x 10-4 Pa resulted in formation of bismuth oxide (most probably Bi2O3) whiskers. The growth mechanism of the whisker was discussed in terms of a vapor-liquid-solid (VLS) mechanism. It is suggested that the liquid droplet of Bi acts as a physical catalyst for growth of bismuth oxide (most probably Bi2O3) whiskers.     

The complexes of bismuth(III) and nitrilotriacetic acid

The reaction between bismuth(III) and nitrilotriacetic acid (NTA or H(3)X) has been investigated by ultraviolet spectrophotometry. It has been established that bismuth(III) and NTA form two complexes with compositions bismuth(III): NTA = 1:1 and 1:2. The absorption maxima are at 243 nm (1:1) and 271 nm (1:2), the molar absorptivities being 8.00 x 10(3) and 8.20 x 10(3) l.mole(-1).cm(-1) respectively. The stability constants (at mu = 1.0) are: log beta(BiX) = 17.53 +/- 0.06 and log beta(B)(2)(3-) = 26.56 +/- 0.07. The possibility of the analytical application of BiX is briefly discussed.     

The crystal structure of Bi14I4 condensed bismuth clusters

The crystal structure of Bi₁₄I₄ — the final known member of binary bismuth halides — was determined by the single crystal X-ray diffractometer technique (P2₁/m, Z = 1, a = 13.309(3) Å, b = 11.447 (3) å, c = 4.342(1) å, γ = 92.08(3)°, R/R_w = 0.060/0.060 for 369 reflections, sinθ/λ≤ 0.593, MoKγ). The structure consists of condensed bismuth clusters and is build up from infinite one-dimensional bismuth nets running along the c-axis and limited by iodine atoms in another direction. The common structural features of bismuth subhalides containing condensed clusters are also considered based on the analysis of interatomic distances and bond angles. The influence of the lone pair of electrons of the bismuth atom on the geometry of bismuth coordination polyhedra, and the connection between bismuth atoms coordination and the formal oxidation state of these atoms is discussed.     

Extraction and separation of bismuth(III)

Separation of bismuth from beryllium, lead, iron(III), indium, scandium, lanthanum, antimony(III), zirconium, titanium, thorium, vanadium(V), molybdenum(VI), uranium (VI) and chromium(VI) is achieved by selective extraction of bismuth from 0.1M sodium salicylate solution (adjusted to pH 7) into mesityl oxide (MeO). The extracted species is Bi (HOC(6)H(4)COO)(3).3MeO. The results are accurate within +/- 0.5%, with a standard deviation of 0.8%. The separation and determination of bismuth takes only 15 min.     

Spectrophotometric determination of bismuth with diethylenetriaminepenta-acetic acid

Diethylenetriaminepenta-acetic acid is used for spectrophotometric determination of bismuth (at 270 nm) in 1.6 M perchloric acid. The system obeys Beer's law in the range 1–40 μg/ml. The method has been tested for the determination of bismuth in pure lead and polymetallic ores.     

Potentiometric studies on bismuth ferrocyanide and the determination of bismuth

Summary The reaction between bismuth nitrate and ferrocyanides of alkali metals such as sodium, potassium, lithium and ammonium, has been studied potentiometrically using platinum as an indicator electrode in conjunction with a saturated calomel electrode through KNO₃ bridge. The equivalence point obtained from the maximum value of dE/dV corresponds to the formation and complete precipitation of a compound having molecular formula BiMFe(CN)₆, where M represents an alkali metal. The potentiometric curves are symmetrical on both sides of the end point and the results obtained are very accurate and reproducible. The method of potentiometric titrations, though simple, offers a rapid and accurate means for the determination of bismuth solutions at fairly low concentrations. The effect of addition of ethanol and electrolytes on the course of the reaction has been studied.     

Ab initio calculations on bismuth cluster polycations

Ab initio calculations on bismuth polycationic species of the types Bi(n(n-2))+, Bi(n(n-4))+, and Bi(n(n-6))+ (n = 3 - 12) were performed at the Hartree-Fock and density functional theory levels in order to investigate their general properties and the applicability of Wade's rules on bismuth polycations. Some exceptions to Wade's rules were encountered, and, moreover, several predicted and calculated minima show only meta-stable behavior. The bonding in bismuth polycations is characterized by a high degree of electron delocalization and "three-dimensional aromaticity".     

Synthesis of Bis(tricarbonylcyclopentadienylmolybdenum)bismuth(III) Chloride and Its Reaction with Metals

Polynuclear organometallic compounds [CpMo(CO)₃]₂BiCl and [CpMo(CO)₃]BiCl₂ were prepared by reaction of bismuth with tricarbonylcyclopentadienylmolybdenum chloride in dimethyl sulfoxide (DMSO). [CpMo(CO)₃]₂BiCl is reduced with magnesium or indium in tetrahydrofuran to give bismuth, [CpMo(CO)₃]₃Bi, and magnesium or indium chloride. In the presence of DMSO, the reaction of [CpMo(CO)₃]₂BiCl with magnesium or indium yields bismuth and the organomolybdenum derivative of magnesium or lithium, respectively.     

Determination of mercury in bismuth by neutron activation analysis

A method has been developed for the determination of traces of mercury in bismuth by neutron activation analysis. After sample irradiation at a flux of 7 · 10¹³ n cm^-2 s^-1 for 20 min, mercury was separated from bismuth by addition of ammonium sulfide and re-dissolution of bismuth (matrix) sulfide with nitric acid, and filtration of sulfur containing mercury on a membrane filter. The activity of the 68- or 68–77-keV region, counted with a Ge(Li) or NaI(Tl) detector, was used for quantitative measurements. The method was applied to bismuth samples containing 0.1–100 p.p.m. of mercury.     

Interaction of bismuth(III) oxide with formic acid solutions

The interaction of bismuth(III) oxide with formic acid solutions at 22 and 55°C was studied using X-ray powder diffraction, thermogravimetry, electron microscopy, IR spectroscopy, and chemical analysis. Solubility curves were found to comprise two branches due to formates of compositions Bi(COOH)₃ and BiOCOOH forming in the system. Thermal decomposition of bismuth formates is shown to be a promising route for the synthesis of metallic bismuth, as well as of tetragonal (β) and monoclinic (α) bismuth oxides.     

Micro-heterometric determination of bismuth with sodium diethyldithiocarbamate

The reaction between bismuth(III) and sodium diethyldithiocarbamate was investigated. The conditions necessary for the heterometric determination of small amounts ot bismuth in other metals were studied. Various complexing agents were used. Methods and conditions are presented for the direct determination of bismuth (~2%) in salts of the following cations: Ca⁺², Ba⁺², Mg⁺², Zn⁺², Mn⁺², Co⁺², Ni⁺², Al⁺², Cr⁺³, Fe⁺³, Cd⁺², Pb⁺², Hg⁺² and Ag⁺. A titration lasted 10–15 minutes, and the error in most cases was close to zero.     

乙酸除铋火试金法测定粗铋中的金银含量

建立了用乙酸分离粗铋中铋-火试金重量法测定粗铋中金和银含量的方法。首先把粗铋焙烧氧化,然后用乙酸溶解粗铋的氧化物,过滤除去铋,消除铋对火试金法的干扰,将沉淀物灰化后,配料、高温熔融,熔态的金属铅捕集试样中的贵金属形成铅扣,将铅扣灰吹,得到金银合粒,用硝酸溶解分离金,用重量法测定金含量。方法准确度高,精密度好,金的加标回收率为99.2%～101%,银的加标回收率为98.2%～99.7%。能很好地满足粗铋中金、银的测定。