Ultrasonically enhanced electrochemical oxidation of ibuprofen

A hybrid advanced oxidation process combining sonochemistry (US) and electrochemistry (EC) for the batch scale degradation of ibuprofen was developed. The performance of this hybrid reactor system was evaluated by quantifying on the degradation of ibuprofen under the variation in electrolytes, frequency, applied voltage, ultrasonic power density and temperature in aqueous solutions with a platinum electrode. Among the methods examined (US, EC and US/EC), the hybrid method US/EC resulted 89.32%, 81.85% and 88.7% degradations while using NaOH, H₂SO₄ and deionized water (DI), respectively, with a constant electrical voltages of 30 V, an ultrasound frequency of 1000 kHz, and a power density of 100 W L⁻¹ at 298 K in 1 h. The degradation was established to follow pseudo first order kinetics. In addition, energy consumption and energy efficiencies were also calculated. The probable mechanism for the anodic oxidation of ibuprofen at a platinum electrode was also postulated.     

High temperature operation of edge-emitting photonic-crystal distributed-feedback quantum cascade lasers at λ∼7.6 μm

We present large-area, edge-emitting, photonic-crystal (PC) distributed-feedback (DFB) quantum cascade lasers (QCLs) emitting at λ∼7.6 μm and operating up to a heat sink temperature of 80 °C. The lasers use the anticrossing of index- and Bragg-guided dispersions of rectangular lattice to control the optical mode in the wafer plane. Single-mode operation with a high signal-to-noise ratio of about 20 dB and narrow beam divergence of 6.2° was obtained. A high peak power of 630 mW at 20 °C and still more than 160 mW at 60 °C was observed. Such a high performance single-mode device is very important to expand the potential applications in the long-wave infrared range.     

Generation of tunable and narrow linewidth continuous-wave yellow laser by sum–frequency mixing of diode-pumped solid-state Nd:YAG ring lasers

We report a tunable, narrow linewidth and high beam quality continuous-wave (CW) yellow laser system at 589 nm. The system is an all solid-state design employing single-pass sum–frequency generation in a KTP crystal by mixing the 1064 nm with 1319 nm lines of two side-pumped Nd:YAG enforcing unidirectional ring lasers. With this method, a CW yellow laser at 589.159 nm with an output power of 0.8 W, a linewidth less than 1.5 GHz and a beam quality M² = 1.29 is obtained. The wavelength of the laser also can be precisely tuned from 589.112 to 589.181 nm in step-length of about 0.22 pm.     

Beam dynamics of 20 MeV MIRRORCLE-type tabletop storage ring

An experimental study on beam dynamics in MIRRORCLE-20, a tabletop storage ring of 15 cm orbit radius, was performed. Measurement of the infrared (IR) synchrotron light is the tool of this study. The IR emission is enhanced by a circular optics, named photon storage ring (PhSR), placed around the electron orbit, and is collected by a magic mirror associated with two plane mirrors in the storage ring. The measured average IR power in mid-IR region (λ < 50 μm) is ～59 mW. The observed stored beam current is about 1.2 A at maximum, which represents a record for a storage ring. The observed beam size is about 74 × 3 mm². We conclude that this very long beam size is due to the large betatron oscillation of 2/3 resonance injection.     

Novel bending sensor based on a meniscus shaped beam with LPG

A novel bending sensor based on a long period fiber grating (LPG) is presented. A LPG was glued into a V-shaped groove, which lies on the lower surface of a meniscus shaped beam. It is found that the transmission optical power of the LPG changed linearly with the variation of the bending of the beam. The bending applied on the beam can be measured by detecting the intensity variation of the LPG's resonant dip wavelength. Under a relative large bending measured range from 0 to 7.5 m^?1, the sensitivity of 3.003 dB m^?1 and curvature resolution of 0.001 m^?1 have been achieved for the proposed bending sensor.     

Coherent beam combining of two fiber amplifiers using stochastic parallel gradient descent algorithm

We demonstrate the coherent beam combining of fiber amplifiers using a stochastic parallel gradient descent (SPGD) algorithm, producing a total output power of 23 W. Active phase control on each amplifier is performed by running the SPGD algorithm on a DSP chip with updating rate of almost 100 kHz. Experimental results show that power encircled in the target pinhole in closed-loop mode is 1.85 times more than that in open-loop mode, which is 92% of the ideal case. The fringe contrast of the far-field fringe pattern is as high as 92% when the system is in closed-loop mode. The whole system in closed-loop mode performs well in a long-time observation.     

Beam shaping for the relay mirror system

The model of two-Cassegrain-telescopes system used in a relay mirror system is established and the theory of beam shaping for the relay mirror system as well as optimization control algorithm is analyzed. Experiment of the reduced-scale relay mirror system with 3 mm-caliber transmitter and 0.27 m propagation distance was done. The results show that power coupling efficiency of the system without beam shaping is 72.67% and power coupling efficiency of the system with beam shaping is 84.14%.     

Investigation of optimum condition in oxygen gas-assisted laser cutting

Laser cutting characteristics including power level and cutting gas pressure are investigated in order to obtain an optimum kerf width. The kerf width is investigated for a laser power range of 50–170 W and a gas pressure of 1–6 bar for steel and mild steel materials. Variation of sample thickness, material type, gas pressure and laser power on the average cut width and slot quality are investigated. Optimum conditions for the steel and mild steel materials with a thickness range of 1–2 mm are obtained. The optimum condition for the steel cutting results in a minimum average kerf width of 0.2 mm at a laser power of 67 W, cutting rate of 7.1 mm/s and an oxygen pressure of 4 bar. A similar investigation for the mild steel cutting results in a minimum average kerf width of 0.3 mm at the same laser power of 67 W, cutting rate of 9.5 mm/s, and an oxygen pressure of 1 bar. The experimental average kerf is about 0.3 mm, which is approximately equal to the estimated focused beam diameter of 0.27 mm for our focusing lens (f=4 cm and 100 W power). This beam size leads to a laser intensity of about 1.74×10⁹ W/m² at the workpiece surface. The estimated cutting rate from theoretical calculation is about 8.07 mm/s (1.0 mm thickness and 100 W power), which agrees with the experimental results that is 7.1 mm/s for 1.0 mm thickness of mild steel at the laser power of 88 W.     

A high-power continuous-wave diffraction-limited Nd:GdVO4 laser operating at 1.34 μm

High-power and high beam quality continuous-wave (CW) Nd:GdVO₄ lasers operating at 1.34 μm were experimentally demonstrated. The lasers consisted of either one or two crystals, which were both end-pumped by high-power fiber-coupled diode lasers. With one crystal, the maximum CW output power generated was 8.4 W. When two crystals were used, a maximum output power of 15.7 W was achieved with the incident pump power of 76.2 W, showing a slope efficiency of 26.2% and an optical-to-optical efficiency of 20.6%. The beam divergence at an output power of 15 W was measured to be about two times that of the diffraction limit.     

A beam shaping design for coupling high power diode laser stack to fiber with capability of spectral narrowing and stabilizing

We applied a VHG-FAC lens in our design in this work to collimate the fast axis and lock the output spectrally. We used a beam shaping technique to improve the beam symmetry and power density of a high power diode laser stack with a stripe mirror plate, a V-Stack mirror and polarization beam combining elements. By this technique, the beam of a high power diode laser stack is effectively coupled into a standard 365 μmcore diameter and a NA = 0.22 fiber. By this technique, compactness, higher efficiency, narrower spectral line width and lower production cost of the diodes are possible.     

Spectroscopy and efficient laser emission of Yb3+: LuAG single crystal grown by μ-PD

A LuAG shaped rod crystal, doped with Yb³⁺, has been grown by μ-PD technique. The crystal diameter was about 3 mm and the length around 130 mm. A complete spectroscopic investigation in the temperature range 10–300 K is reported and data has been utilized to model the laser behavior. In the laser experiment the Yb:LuAG sample was placed in an X cavity and pumped longitudinally obtaining an efficient CW laser emission. The Yb:LuAG laser yielded a maximum output power of 23 mW with a slope efficiency of 32% and a threshold around 35 mW, at lasing wavelength of 1030 nm. No significant depolarization effects were observed, indicating a crystal growth with negligible stress. The output beam profile was investigated, yielding M² ≈ 1.0 in both directions, further confirming the good optical quality of the sample.     

An eye-safe KTiAsO4 intracavity optical parametric oscillator driven by a diode pumped composite Nd:YAG/Cr4+:YAG laser

A mini eye-safe KTiAsO₄ intracavity optical parametric oscillator (IOPO) employing the shared cavity configuration and driven by a diode-end-pumped composite Nd:YAG/Cr⁴⁺:YAG laser is demonstrated in this paper. Under an incident laser diode power of 11 W, a maximum average output power of 424 mW at 1534 nm was obtained. The corresponding signal pulse width and repetition rate were 1.2 ns and 16.7 kHz, respectively. The fluctuation of the average signal output power over long-term operation was found to be ±3.0%. A theoretical model for the compact IOPO was also presented in this paper.     

Polymer electrolytes based on copolymer of poly(ethylene glycol) dimethacrylate and imidazolium ionic liquid

Polymer electrolytes based on the copolymer of N-vinylimidazolium tetrafluoroborate (VyImBF₄) and poly(ethylene glycol) dimethacrylate (PEGDMA) have been prepared. Ethylene carbonate (EC) and LiClO₄ are added to form gel polymer electrolytes. The chemical structure of the samples and the interactions between the various constituents are studied by FT-IR. TGA results show that these polymer electrolytes have acceptable thermal stability, are stable up to 155 °C. Measurements of conductivity are carried out as a function of temperature, VyImBF₄ content in poly(VyImBF₄-co-PEGDMA), and the concentration of EC and LiClO₄. The conductivity increases with PEGDMA and EC content. The highest conductivity is obtained with a value of 2.90 × 10^? 6 S cm^? 1 at room temperature for VP1/EC(25 wt.%)–LiClO₄ system, corresponding to the LiClO₄ concentration of 0.70 mol kg^? 1 polymer.     

Synthesis of porous Cu-BTC with ultrasonic treatment: Effects of ultrasonic power and solvent condition

Cu-BTC (BTC = 1,3,5-benzenetricarboxylate) metal organic framework (MOF) was synthesized using different solvent conditions with ultrasonic treatment. Solvent mixtures of water/N,N-dimethylformamide (DMF), water/ethanol were used for the reactions with or without a variety of bases under 20 kHz ultrasonically treated conditions. Prepared crystals were purified through 30 min of sonication to remove unreacted chemicals. Treatment time and ultrasonic power effects were compared to get optimum synthetic condition. The characterization of MOF powders was performed by scanning electron microscopy, X-ray powder diffraction, infrared-spectroscopy, thermo-gravimetric analysis and specific surface determination using the BET method. Isolated crystal yields varied with different solvent and applied ultrasonic power conditions. A high isolated crystal yield of 86% was obtained from water/ethanol/DMF solvent system after 120 min of ultrasonic treatment at 40% power of 750 W. Different solvent conditions led to the formation of Cu-BTC with different surface area, and an extremely high surface area of 1430 m²/g was obtained from the crystals taken with the solvent condition of water:DMF = 70:30.     

Design and development of an optical beam splitter assembly and high precision colinearity measurements of laser beams

Laser beams with extremely high colinearity are often required where precision position monitoring is important. In order to achieve the said objective, a special type of Laser Beam Splitter Assembly (BSA) has been designed and fabricated in a very small volume due to space constraints. The main features and details of such a system are described here. This type of beam splitter assembly coupled with a diode laser through fibers can be remotely used for alignment or position monitoring of different medium to large size structures with a reconstruction accuracy of 10 μm. In this way, BSA generates two counter propagating laser beams from a single diode laser coupled to an optical fiber. In the present work, the colinearity between two beams within 1 mrad with the variation of 50 μrad has been achieved. The laser's power in the two arms may be controlled precisely, which is an important feature of this BSA. The BSA has been tested to work over a temperature range between ?20 °C to +40 °C. It has also been exposed to 1.0 MeV neutrons at a flux of ～5.0×10¹⁰ n/cm²/s and found compatible.     

The disinfection effect of a novel continuous-flow water sterilizing system coupling dual-frequency ultrasound with sodium hypochlorite in pilot scale

In this paper, a self-designed novel continuous-flow water disinfection system coupling dual-frequency ultrasound (US) with chemical disinfectant sodium hypochlorite (NaClO) was tested in a pilot scale using a simulated effluent containing Bacillus subtilis (B. subtilis), one of the indicators of water treatment efficiency. A suspension having a B. subtilis concentration of approximately 10⁴ CFU/mL was introduced into the system to (1) investigate disinfection efficiency of US pretreatment with NaClO (US + NaClO) and simultaneous US and NaClO (US/NaClO) disinfection under different single frequencies; (2) further examine the disinfection efficiency of these two processes with dual-frequency US; and (3) identify dosage reduction of chlorine in this disinfection system. The results demonstrated that lower dual-frequency (17 kHz + 33 kHz) US pretreatment with NaClO disinfection and simultaneous higher dual-frequency (70 kHz + 100 kHz) US and NaClO were beneficial to bacterial inactivation in terms of sterilizing efficiency. It has also been observed that US pretreatment with lower combination of 17 + 33 kHz frequencies showed better enhancement in which log reduction reached to 3.82 after 10 min chlorine reaction (chlorine alone was 0.22 log reduction), nearly 1 log reduction higher than single frequencies at the same constant power. Consequently, at equivalent power dissipation levels, US of lower frequencies combination pretreatment with NaClO disinfection performed such a promising process that one-thirds (from 12 mg/L NaClO reduced to 8 mg/L NaClO) of the required NaClO dosage was reduced for the ideal disinfection efficiency of 4 log reduction, namely 100% disinfection. And the utilization efficiency of NaClO was increased from 37.67% to 85.25% in 30 min of treatment time using an optimized combination of pretreatment and chlorination.     

RF behavior of triple-frequency high power fusion gyrotron

The RF behavior of high power, triple frequency (170-, 127.5-, and 85 GHz) gyrotron for fusion application is presented in this paper. The operating mode selection is discussed in detail for each corresponding frequencies and TE_34,10, TE_25,8 and TE_17,5 modes are selected as the operating mode for 170 GHz, 127.5 GHz and 85 GHz operation of the device, respectively. The interaction cavity geometry and beam parameters are finalized by the cold cavity analysis and beam-wave interaction simulations. Considering the beam parameters and the beam launching positions in cavity (beam radius), the design of Magnetically Tunable MIG (MT-MIG) is also presented. Results of MT-MIG confirm the beam launching with desired beam parameters at the beam radius corresponding to the selected operating modes for all three frequencies. The CVD diamond window is also designed for RF power transmission. The beam-wave interaction simulations confirm more than 1 MW power at all three frequencies (170-, 127.5-, and 85 GHz).     

Towards a 1 MW, 170 GHz gyrotron design for fusion application

The electrical design of different components of 1 MW, 170 GHz gyrotron such as, magnetron injection gun, cylindrical interaction cavity and collector and RF window is presented in this article. Recently, a new project related to the development of 170 GHz, 1 MW gyrotron has been started for the Indian Tokamak. TE_34,10 mode is selected as the operating mode after studied the problem of mode competition. The triode type geometry is selected for the design of magnetron injection gun (MIG) to achieve the required beam parameters. The maximum transverse velocity spread of 3.28% at the velocity ratio of 1.34 is obtained in simulations for a 40 A, 80 kV electron beam. The RF output power of more than 1 MW with 36.5% interaction efficiency without depressed collector is predicted by simulation in single-mode operation at 170 GHz frequency. The simulated single-stage depressed collector of the gyrotron predicted the overall device efficiencies >55%. Due to the very good thermal conductivity and very weak dependency of the dielectric parameters on temperature, PACVD diamond is selected for window design for the transmission of RF power. The in-house developed code MIGSYN and GCOMS are used for initial geometry design of MIG and mode selection respectively. Commercially available simulation tools MAGIC and ANSYS are used for beam–wave interaction and mechanical analysis respectively.     

High quality mid-wavelength infrared InAs/GaSb superlattices by exploring the optimum molecular beam epitaxy growth process

In this paper we report on the growth of mid-wavelength infrared superlattice materials by molecular beam epitaxy. We focused on the effects of process parameters, such as arsenic beam equivalent pressure and shutter sequences, on the key material properties, such as the lattice mismatch and the surface morphology. Though a smaller As beam equivalent pressure helps to reduce the lattice mismatch between the superlattice and the GaSb substrate, the As beam equivalent pressure itself has a lower limit below which the material’s surface morphology will degrade. To achieve fully lattice-matched superlattice materials, a novel shutter sequence in the growth process was designed. With well-designed interface structures, a high quality P-I-N superlattice mid-infrared detector structure was realized. At 77 K the dark current density at −50 mV bias was 2.4 × 10⁻⁸ A/cm² and the resistance-area product (RA) at maximum (−50 mV bias) was 2.4 × 10⁶ Ω cm², and the peak detectivity was then calculated to be 9.0 × 10¹² cm Hz^1/2/W. The background limited infrared photodetector (BLIP) level can be achieved at a temperature of 113 K.     

A diode end-pumped passively Q-switched Nd:YAG/KTA Raman laser

A diode end-pumped passively Q-switched Nd:YAG/KTA intracavity Raman laser is presented. A KTA crystal with a size of 5 mm × 5 mm × 25 mm is used as the Raman active medium and its 234 cm^?1 Raman mode is employed to finish the conversion from 1064 nm fundamental laser to 1091 nm Raman laser. A 2 mm thick Cr⁴⁺:YAG crystal is used as the saturable absorber. With an LD pump power of 7.5 W, the first-Stokes power of 250 mW is obtained with a pulse repetition frequency of 14.5 kHz. The corresponding diode-to-Stokes conversion efficiency is 3.3% and the pulse energy is 17.2 μJ. Pulse width is measured to be 12.6 ns and peak power is 1.4 kW.