Advanced oxidation of Reactive Blue 181 solution: A comparison between Fenton and Sono-Fenton Process

In this work, the decolorization of C.I. Reactive Blue 181 (RB181), an anthraquinone dye, by Ultrasound and Fe²⁺ H₂O₂ processes was investigated. The effects of operating parameters, such as Fe²⁺ dosage, H₂O₂ dosage, pH value, reaction time and temperature were examined. Process optimisation [pH, ferrous ion (Fe²⁺), hydrogen peroxide (H₂O₂), and reaction time], kinetic studies and their comparison were carried out for both of the processes. The Sono-Fenton process was performed by indirect sonication in an ultrasonic water bath, which was operated at a fixed 35-kHz frequency. The optimum conditions were determined as [Fe²⁺] = 30 mg/L, [H₂O₂] = 50 mg/L and pH = 3 for the Fenton process and [Fe²⁺] = 10 mg/L, [H₂O₂] = 40 mg/L and pH = 3 for the Sono-Fenton process. The colour removals were 88% and 93.5% by the Fenton and Sono-Fenton processes, respectively. The highest decolorization was achieved by the Sono-Fenton process because of the production of some oxidising agents as a result of sonication. The paper also discussed kinetic parameters. The decolorization kinetic of RB181 followed pseudo-second-order reaction (Fenton study) and Behnajady kinetics (Sono-Fenton study).     

Rapid ultrasound-assisted magnetic microextraction of gallic acid from urine,plasma and water samples by HKUST-1-MOF-Fe3O4-GA-MIP-NPs: UV–vis detection and optimization study

Magnetite (Fe₃O₄ nanoparticles (NPs)) HKUST-1 metal organic framework (MOF) composite as a support was used for surface imprinting of gallic acid imprinted polymer (HKUST-1-MOF-Fe₃O₄-GA-MIP) using vinyltrimethoxysilane (VTMOS) as the cross-linker. Subsequently, HKUST-1-MOF-Fe₃O₄-NPs-GA-MIP characterized by FT-IR, XRD and FE-SEM analysis and applied for fast and selective and sensitive ultrasound assisted dispersive magnetic solid phase microextraction of gallic acid (GA) by UV–Vis (UA-DMSPME-UV-Vis) detection method. Plackett–Burman design (PBD) and central composite design (CCD) according to desirability function (DF) indicate the significant variables among the extraction factors vortex (mixing) time (min), sonication time (min), temperature (°C), eluent volume (L), pH and HKUST-1-MOF-Fe₃O₄-NPs-GA-MIP mass (mg) and their contribution on the response. Optimum conditions and values correspond to pH, HKUST-1-MOF-Fe₃O₄-NPs-GA-MIP mass, sonication time and the eluent volume were set as follow 3.0, 1.6 mg, 4.0 min and 180 μL, respectively. The average recovery (ER%) of GA was 98.13% with desirability of 0.997, while the present method has best operational performance like wide linear range 8–6000 ng mL⁻¹ with a Limit of detection (LOD) of 1.377 ng mL⁻¹, limit of quantification (LOQ) 4.591 ng mL⁻¹ and precision (<3.50% RSD). The recovery of GA in urine, human plasma and water samples within the range of 92.3–100.6% that strongly support high applicability of present method for real samples analysis, which candidate this method as promise for further application.     

Comparative study on ultrasonic assisted adsorption of dyes from single system onto Fe3O4 magnetite nanoparticles loaded on activated carbon: Experimental design methodology

The present study the ultrasound assisted adsorption of dyes in single system onto Fe₃O₄ magnetite nanoparticles loaded on activated carbon (Fe₃O₄-MNPs-AC) was described following characterization and identification of this adsorbent by conventional techniques likes field emission scanning electron microscopy, transmission electron microscopy, particle-size distribution, X-ray diffraction and Fourier transform infrared spectroscopy. A central composite design in conjunction with a response surface methodology according to f-test and t-test for recognition and judgment about significant term led to construction of quadratic model which represent relation among responses and effective terms. This model has unique ability to predict adsorption data behavior over a large space around central and optimum point. Accordingly Optimum conditions for well and quantitative removal of present dyes was obtained best operation and conditions: initial SY, MB and EB dyes concentration of 15, 15 and 25 mg L⁻¹, 4.0, 6.0 and 5.0 of pH, 360, 360 and 240 s sonication time and 0.04, 0.03 and 0.032 g of Fe₃O₄-MNPs-AC. Replication of similar experiment (N = 5) guide that average removal percentage of SY, MB and EB were found to be 96.63 ± 2.86%, 98.12 ± 1.67% and 99.65 ± 1.21% respectively. Good agreement and closeness of Predicted and experimental result and high adsorption capacity of dyes in short time strongly confirm high suitability of present method for waste water treatment, while easy separation of present nanoparticle and its good regeneration all support good applicability of Fe₃O₄-MNPs-AC for waste water treatment. The kinetic study can be represented by combination of pseudo second-order and intraparticle diffusion. The obtained maximum adsorption capacities correspond to Langmuir as best model for representation of experimental data correspond to dyes adsorption onto Fe₃O₄-MNPs-AC were 76.37, 78.76 and 102.00 mg g⁻¹ for SY, MB and EB, respectively. In addition, the performance comparison of ultrasound-assisted, magnetic stirrer assisted and vortex assisted adsorption methods demonstrates that ultrasound is an effective and good choice for facilitation of adsorption process via. Compromise of simple and facile diffusion.     

Sonophotocatalytic degradation of trypan blue and vesuvine dyes in the presence of blue light active photocatalyst of Ag3PO4/Bi2S3-HKUST-1-MOF: Central composite optimization and synergistic effect study

An efficient simultaneous sonophotocatalytic degradation of trypan blue (TB) and vesuvine (VS) using Ag₃PO₄/Bi₂S₃-HKUST-1-MOF as a novel visible light active photocatalyst was carried out successfully in a continuous flow-loop reactor equipped to blue LED light. Ag₃PO₄/Bi₂S₃-HKUST-1-MOF with activation ability under blue light illumination was synthesized and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), photoluminescence (PL) and diffuse reflectance spectra (DRS). The effect of operational parameters such as the initial TB and VS concentration (5–45 mg/L), flow rate (30–110 mL/min), irradiation and sonication time (10–30 min), pH (3–11) and photocatalyst dosage (0.15–0.35 g/L) has been investigated and optimized using central composite design (CCD) combined with desirability function (DF). Maximum sonophotodegradation percentage (98.44% and 99.36% for TB and VS, respectively) was found at optimum condition set as: 25 mg/L of each dye, 70 mL/min of solution flow rate, 25 min of irradiation and sonication time, pH 6 and 0.25 g/L of photocatalyst dosage. At optimum conditions, synergistic index value was obtained 2.53 that indicated the hybrid systems including ultrasound irradiation and photocatalysis have higher efficiency compared with sum of the individual processes.     

Preparation and characterization of Fe3O4(1 1 1) nanoparticles and thin films on Au(1 1 1)

Fe₃O₄ nanoparticles and thin films were prepared on the Au(1 1 1) surface and characterized using X-ray photoelectron spectroscopy (XPS) and scanning tunneling microscopy (STM). Fe₃O₄ was formed by annealing α-Fe₂O₃(0 0 0 1) structures on Au(1 1 1) at 750 K in ultrahigh vacuum (UHV) for 60 min. Transformation of the α-Fe₂O₃(0 0 0 1) structures into Fe₃O₄ nanoparticles and thin films was supported by XPS. STM images show that during the growth procedure used, Fe₃O₄ initially appears as nanoparticles at low coverages, and forms thin films at ～2 monolayer equivalents (MLE) of iron. Two types of ordered superstructures were observed on the Fe₃O₄ particles with periodicities of ～50 and ～42 Å, respectively. As the Fe₃O₄ particles form more continuous films, the ～50 Å feature was the predominant superstructure observed. The Fe₃O₄ structures at all coverages show a hexagonal unit cell with a ～3 Å periodicity in the atomically resolved STM images.     

Identification of iron oxide phases in thin films grown on Al2O3(0 0 0 1) by Raman spectroscopy and X-ray diffraction

We report on the identification of Fe₃O₄ (magnetite) and α-Fe₂O₃ (hematite) in iron oxide thin films grown on α-Al₂O₃(0 0 0 1) by evaporation of Fe in an O₂-atmosphere with a thickness of a few unit cells. The phases were observed by Raman spectroscopy and confirmed by X-ray diffraction (XRD). Magnetite appeared independently from the substrate temperature and could not be completely removed by post-annealing in an oxygen atmosphere as observed by X-ray diffraction. In the temperature range between 400 °C and 500 °C the X-ray diffraction shows that predominantly hematite is formed, the Raman spectrum shows a mixture of magnetite and hematite. At both lower and higher substrate temperatures (300 °C and 600 °C) only magnetite was observed. After post-annealing in an O₂-atmosphere of 5 × 10^?5 mbar only hematite was detectable in the Raman spectrum.     

Sonochemical fabrication of Fe3O4 nanoparticles on reduced graphene oxide for biosensors

This study synthesized Fe₃O₄ nanoparticles of 30–40 nm by a sonochemical method, and these particles were uniformly dispersed on the reduced graphene oxide sheets (Fe₃O₄/RGO). The superparamagnetic property of Fe₃O₄/RGO was evidenced from a saturated magnetization of 30 emu/g tested by a sample-vibrating magnetometer. Based on the testing results, we proposed a mechanism of ultrasonic waves to explain the formation and dispersion of Fe₃O₄ nanoparticles on RGO. A biosensor was fabricated by modifying a glassy carbon electrode with the combination of Fe₃O₄/RGO and hemoglobin. The biosensor showed an excellent electrocatalytic reduction toward H₂O₂ at a wide, linear range from 4 × 10^?6 to 1 × 10^?3 M (R² = 0.994) as examined by amperometry, and with a detection limit of 2 × 10^?6 M. The high performance of H₂O₂ detection is attributed to the synergistic effect of the combination of Fe₃O₄ nanoparticles and RGO, promoting the electron transfer between the peroxide and electrode surface.     

Dephenolization,dearomatization and detoxification of olive mill wastewater with sonication combined with additives and radical scavengers

In this study, the effects of some additives [manganese (III) oxide (Mn₃O₄), Cu⁺², Fe⁰ and potassium iodate (KIO₃)] and some radical scavengers [sodium carbonate (Na₂CO₃), perfluorohexane (C₆F₁₄) and t-butyl alcohol (C₄H₁₀O)] on the sonication of olive mill effluent wastewater (OMW) were investigated since the wastewaters of this industry are removed with low efficiencies. The maximum total phenol and total aromatic amines (TAAs) removal efficiencies were 88% and 79%, respectively, at 60 °C with only 150 min sonication. The maximum phenol removal was found as 98% with 19 mg L⁻¹ perfluorohexane and 5 mg L⁻¹ Fe⁰ while the maximum TAAs removal was 99% with 16 mg L⁻¹ KIO₃. Catechol, tyrosol, quercetin, caffeic acid, 4-methyl catechol, 2-phenylphenol (2-PHE) and 3-phenyl phenol (3-PHE) were detected as phenol intermediates while trimethlyaniline, aniline, o-toluidine, o-anisidine, dimethylaniline, ethylbenzene and durene were identified as TAAs in the OMW. The maximum acute toxicity removals were 96% and 99% in Vibrio fischeri and Daphnia magna, respectively. Total phenol, TAAs and the toxicity in an OMW were removed efficiently and cost-effectively through sonication.     

Oxygen plasma activation of Cr(CO)6 on α-Fe2O3(0001)

The chemistry of Cr(CO)₆ on the Fe₃O₄(111) surface termination of α-Fe₂O₃(0001) was explored using temperature programmed desorption (TPD), Auger electron spectroscopy (AES), static secondary ion mass spectrometry (SSIMS) and low energy electron diffraction (LEED) both with and without activation from an oxygen plasma source. No thermal decomposition of Cr(CO)₆ was detected on the surface in the absence of O₂ plasma treatment, with first layer molecules desorbing in TPD at 215 K from a close-packed overlayer. The interaction of first layer Cr(CO)₆ with the Fe₃O₄(111)-termination was weak, desorbing only ～ 30 K above the leading edge of the multilayer state. Activation of multilayer coverages of Cr(CO)₆ with the O₂ plasma source at 100 K resulted in complete conversion of the outer Cr(CO)₆ layers, presumably to a disordered Cr oxide film, with Cr(CO)₆ molecules near the surface left unaffected. Absence of CO or CO₂ desorption states suggests that all carbonyl ligands are liberated for each Cr(CO)₆ molecule activated by the plasma. AES and SSIMS both show that O₂ plasma activation of Cr(CO)₆ results in a carbon-free surface (after desorption of unreacted Cr(CO)₆). LEED, however, shows that the Cr oxide film was disordered at 600 K and likely O-terminated based on subsequent water TPD. Attempts to order the film at temperatures above 650 K resulted in dissolution of Cr into the α-Fe₂O₃(0001) crystal based on SSIMS, an observation linked to the Fe₃O₄(111) termination of the surface and not to the properties of α-Cr₂O₃/α-Fe₂O₃ corundum interface. Nevertheless, this study shows that O₂ plasma activation of Cr(CO)₆ is an effective means of depositing Cr oxide films on surfaces without accompanying carbon contamination.     

High surface area monodispersed Fe3O4 nanoparticles alone and on physical exfoliated graphite for improved supercapacitors

Highly conductive, unsophisticated and easy to be obtained physical exfoliated graphite (PHG) supporting well dispersed magnetite, Fe₃O₄/PHG nanocomposite, has been prepared by a one-step chemical strategy and physico-chemical characterized. The nanocomposite, favoured by the a-polar nanoparticles (NPs) capping, results in a self-assembled monolayer of monodispersed Fe₃O₄, covering perfectly the hydrophobic surfaces of PHG. The nanocomposite as an electrode material was fabricated into a supercapacitor and characterized by cyclic voltammetry (CV) and galvanostatic charge–discharge measurements. It shows, after a suitable annealing, significant electrochemical properties (capacitance value of 787 F/g at 0.5 A g⁻¹ and a Fe₃O₄/PHG weight ratio of 0.31) and good cycling stability (retention 91% after 30,000 cycles). Highly monodispersed very fine Fe₃O₄ NPs, covered by organic chains, have been also synthesized. The high surface area Fe₃O₄ NPs, after washing to leave a low content of organic chains able to avoid aggregation without excessively affecting the electrical properties of the material, exhibit remarkable pseudocapacitive activities, including the highest specific capacitance over reported for Fe₃O₄ (300 F/g at 0.5 A g⁻¹).     

Sonication induced redox reactions of the Ojén (Andalucía,Spain) vermiculite

Sonication in a 1:1 mixture (volume ratio) of water and concentrated H₂O₂ (30%) is a soft method for particle size reduction of phyllosilicate minerals like vermiculites. Repeated sonication causes a particle size reduction to about 70 nm for the Santa Olalla and to 45 nm for the Ojén-vermiculite. In this context the question arises whether the strong oxidising effect of the hydrogen peroxide affects the oxidation state of the iron in the vermiculites. Therefore, the Fe³⁺/Fe_total ratio before and after sonication was determined by means of Mössbauer spectroscopy. Whereas this ratio was found to remain almost constant in the Santa Olalla vermiculite, it increased from 0.79 to 0.85 in case of the Ojén sample. In the latter case, the oxidation is accompanied by a decrease of the layer charge.Surprisingly, sonication in pure water leads to a decrease of the Fe³⁺/Fe_total ratio in the case of the Ojén-vermiculite, i.e., to an increase of the Fe²⁺ fraction to roughly twice the value before sonication. Again the Fe³⁺/Fe_total ratio of the Santa Olalla vermiculite remains unchanged. The surface area S_BET of the reduced Ojén-vermiculite amounts to 50 m²/g, which is close to the value obtained in the presence of hydrogen peroxide. The results presented should be taken as a warning that particle size reduction by sonication may be accompanied by a change of the redox state and the layer charge of the material.     

Sono-assisted preparation of highly-efficient peroxidase-like Fe3O4 magnetic nanoparticles for catalytic removal of organic pollutants with H2O2

Fe₃O₄ magnetic nanoparticles (Fe₃O₄ MNPs) with much improved peroxidase-like activity were successfully prepared through an advanced reverse co-precipitation method under the assistance of ultrasound irradiation. The characterizations with XRD, BET and SEM indicated that the ultrasound irradiation in the preparation induced the production of Fe₃O₄ MNPs possessing smaller particle sizes (16.5 nm), greater BET surface area (82.5 m² g^?1) and much higher dispersibility in water. The particle sizes, BET surface area, chemical composition and then catalytic property of the Fe₃O₄ MNPs could be tailored by adjusting the initial concentration of ammonia water and the molar ratio of Fe²⁺/Fe³⁺ during the preparation process. The H₂O₂-activating ability of Fe₃O₄ MNPs was evaluated by using Rhodamine B (RhB) as a model compound of organic pollutants to be degraded. At pH 5.4 and temperature 40 °C, the sonochemically synthesized Fe₃O₄ MNPs were observed to be able to activate H₂O₂ and remove ca. 90% of RhB (0.02 mmol L^?1) in 60 min with a apparent rate constant of 0.034 min^?1 for the RhB degradation, being 12.6 folds of that (0.0027 min^?1) over the Fe₃O₄ MNPs prepared via a conventional reverse co-precipitation method. The mechanisms of the peroxidase-like catalysis with Fe₃O₄ MNPs were discussed to develop more efficient novel catalysts.     

Mechanistic study on ultrasound assisted pretreatment of sugarcane bagasse using metal salt with hydrogen peroxide for bioethanol production

This study presents the ultrasound assisted pretreatment of sugarcane bagasse (SCB) using metal salt with hydrogen peroxide for bioethanol production. Among the different metal salts used, maximum holocellulose recovery and delignification were achieved with ultrasound assisted titanium dioxide (TiO₂) pretreatment (UATP) system. At optimum conditions (1% H₂O₂, 4 g SCB dosage, 60 min sonication time, 2:100 M ratio of metal salt and H₂O₂, 75 °C, 50% ultrasound amplitude and 70% ultrasound duty cycle), 94.98 ± 1.11% holocellulose recovery and 78.72 ± 0.86% delignification were observed. The pretreated SCB was subjected to dilute acid hydrolysis using 0.25% H₂SO₄ and maximum xylose, glucose and arabinose concentration obtained were 10.94 ± 0.35 g/L, 14.86 ± 0.12 g/L and 2.52 ± 0.27 g/L, respectively. The inhibitors production was found to be very less (0.93 ± 0.11 g/L furfural and 0.76 ± 0.62 g/L acetic acid) and the maximum theoretical yield of glucose and hemicellulose conversion attained were 85.8% and 77%, respectively. The fermentation was carried out using Saccharomyces cerevisiae and at the end of 72 h, 0.468 g bioethanol/g holocellulose was achieved. Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) analysis of pretreated SCB was made and its morphology was studied using scanning electron microscopy (SEM). The compounds formed during the pretreatment were identified using gas chromatography–mass spectrometry (GC–MS) analysis.     

Ultrasonic-assisted magnetic solid phase extraction of morphine in urine samples by new imprinted polymer-supported on MWCNT-Fe3O4-NPs: Central composite design optimization

Multiwalled carbon nanotubes (MWCNTs) were magnetized with Fe₃O₄ nanoparticles (MWCNTs-Fe₃O₄-NPs) and subsequently coated by vinyl end groups (Vinyltrimethoxysilane). MWCNT-Fe₃O₄-NPs were used as support for a new morphine (MO) molecularly imprinted polymer (MWCNT-Fe₃O₄-NPs@MO-MIP) by surface imprinting polymerization method. The MWCNT-Fe₃O₄-NPs@MO-MIP was characterized by FTIR, VSM and SEM techniques and successfully used for determination of MO. Ultrasonic-assisted magnetic solid phase extraction followed by UV–vis spectrophotometer (UAMSPE-UV–vis) was investigated for MWCNT-Fe₃O₄-NPs@MO-MIP and compared with non-imprinted polymer (NIP) using batch method. Central composite design under response surface methodology was used for the evaluation of the effect of variables, individually, as well as their possible interaction effects on the adsorption process. The variables such as sonication time, MWCNT-Fe₃O₄-NPs@MO-MIP mass, initial concentration of MO and pH were investigated in this study. At optimum experimental conditions, UAMSPE-UV–vis method was exhibited a linear range of 0.8–8.7 mg L⁻¹ of the MO concentration with a detection limit of 0.18 mg L⁻¹. The relative standard deviation for the analyte was found to be lower than 2.32%. The MWCNT-Fe₃O₄-NPs@MO-MIP adsorption capacity was found to be 37.01 mg g⁻¹. The enrichment and preconcentration factors were found to be 107.01 and 98.21, respectively. The developed method was finally applied successfully to the determination of MO in urine and wastewater samples with the recoveries ranged from 96.40 to 105.6%.     

Ultrasonic assisted-Fenton-like degradation of nitrobenzene at neutral pH using nanosized oxides of Fe and Cu

Ultrasonic-assisted heterogeneous Fenton reaction was used for degradation of nitrobenzene (NB) at neutral pH conditions. Nano-sized oxides of α-Fe₂O₃ and CuO were prepared, characterized and tested in degradation of NB (10 mg L⁻¹) under sonication of 20 kHz at 25 °C. Complete degradation of NB was effected at pH 7 in presence of 10 mM H₂O₂ after 10 min of sonication in presence of α-Fe₂O₃ (1.0 g L⁻¹), (k = 0.58 min⁻¹) and after 25 min in case of CuO (k = 0.126 min⁻¹). α-Fe₂O₃ showed also effective degradation under the conditions of 0.1 g L⁻¹ oxide and 5.0 mM of H₂O₂, even though with a lower rate constant (0.346 min⁻¹). Sonication plays a major role in enhancing the production of hydroxyl radicals in presence of solid oxides. Hydroxyl radicals-degradation pathway is suggested and adopted to explain the differences noted in rate constants recorded on using different oxides.     

Mixed conducting perovskite-like ceramics on the base of lanthanum gallate

Ceramic perovskite solid solutions (La_0.9Sr_0.1)[(Ga_1−xM_x)_0.8Mg_0.2]O_3−y, 0 ≤ x ≤ 0.5, M = Fe, Ni, Cr (systems I–III) and brownmillerite solid solutions (La_0.2Sr_1.8)[Ga(Fe_1−xMg_x)]O_5−z, 0 ≤ x ≤ 0.5, (system IV) have been prepared. The samples have been studied by X-ray diffraction and electron microscopy methods, dielectric spectroscopy and permeability measurements. The correlation between the composition, unit cell parameter changes, electrical transport and oxygen permeation properties has been revealed. Introduction of transition metals (Fe, Ni, or Cr), substituting for gallium, ensures the enhancement of the electronic constituent of the conductivity in the perovskite systems I–III. Stabilization of the transition metal high valence states 4+ or 5+ has been suggested for compositions I and III. This leads to a unit cell volume contraction and provides a decrease in the concentration of oxygen vacancies. The oxygen permeability reaches its maximum values in compositions I–III with x ∼ 0.3. On the contrary, increasing concentration of the doping element with lower valence state (magnesium), substituting for iron, determines the expansion of the brownmillerite unit cell volume and provides an increase of the oxygen vacancy concentration, which in turn, favors the enhancement of oxygen permeability of composition IV.     

Ultrasound assisted extraction of Maxilon Red GRL dye from water samples using cobalt ferrite nanoparticles loaded on activated carbon as sorbent: Optimization and modeling

In this research, a selective, simple and rapid ultrasound assisted dispersive solid-phase micro-microextraction (UA-DSPME) was developed using cobalt ferrite nanoparticles loaded on activated carbon (CoFe₂O₄-NPs-AC) as an efficient sorbent for the preconcentration and determination of Maxilon Red GRL (MR-GRL) dye. The properties of sorbent are characterized by X-ray diffraction (XRD), Transmission Electron Microscopy (TEM), Vibrating sample magnetometers (VSM), Fourier transform infrared spectroscopy (FTIR), Particle size distribution (PSD) and Scanning Electron Microscope (SEM) techniques. The factors affecting on the determination of MR-GRL dye were investigated and optimized by central composite design (CCD) and artificial neural networks based on genetic algorithm (ANN-GA). CCD and ANN-GA were used for optimization. Using ANN-GA, optimum conditions were set at 6.70, 1.2 mg, 5.5 min and 174 μL for pH, sorbent amount, sonication time and volume of eluent, respectively. Under the optimized conditions obtained from ANN-GA, the method exhibited a linear dynamic range of 30–3000 ng mL⁻¹ with a detection limit of 5.70 ng mL⁻¹. The preconcentration factor and enrichment factor were 57.47 and 93.54, respectively with relative standard deviations (RSDs) less than 4.0% (N = 6). The interference effect of some ions and dyes was also investigated and the results show a good selectivity for this method. Finally, the method was successfully applied to the preconcentration and determination of Maxilon Red GRL in water and wastewater samples.     

Effect of Fe doping on the room temperature ferromagnetism in chemically synthesized (In1−xFex)2O3 (0 ⩽ x ⩽ 0.07) magnetic semiconductors

Observation of room temperature ferromagnetism in Fe doped In₂O₃ samples (In_1−xFe_x)₂O₃ (0 ⩽ x ⩽ 0.07) prepared by co-precipitation technique is reported. Lattice parameter obtained from powder X software shows distinct shrinkage of the lattice constant indicating an actual incorporation of Fe ions into the In₂O₃ lattice. X-ray diffraction data measurements show that the entire sample exhibits single phase polycrystalline behavior. SEM micrographs showed the prepared powder was in the range 25–36 nm. SEM EDS mapping showed the presence of Fe and In ions in the Fe doped In₂O₃ sample. The highest remanence magnetization moment (6.624 × 10⁻⁴ emu/g) is reached in the sample with x = 0.03.     

Thermal expansion behavior and chemical compatibility of BaxSr1−xCo1−yFeyO3−δ with 8YSZ and 20GDC

Perovskite oxides of the composition Ba_xSr_1−xCo_1−yFe_yO_3−δ(BSCF) were synthesized via a modified Pechini method and characterized by X-ray diffraction, dilatometry and thermogravimetry. Investigations revealed that single-phase perovskites with cubic structure can be obtained for x ≤ 0.6 and 0.2 ≤ y ≤ 1.0. The as-synthesized BSCF powders can be sintered in several hours to nearly full density at temperatures of over 1180 °C. Thermal expansion curves of dense BSCF samples show nonlinear behavior with sudden increase in thermal expansion rate between about 500 °C and 650 °C, due mainly to the loss of lattice oxygen caused by the reduction of Co⁴⁺ and Fe⁴⁺ to lower valence states. Thermal expansion coefficients (TECs) of BSCF were measured to be 19.2–22.9 × 10^− 6 K^− 1 between 25 °C and 850 °C. Investigations showed further that Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ is chemically compatible with 8YSZ and 20GDC for temperatures up to 800 °C, above which severe reactions were detected. After being heat-treated with 8YSZ or 20GDC for 5 h above 1000 °C, Ba_0.5Sr_0.5Co_0.8Fe_0.2O_3−δ was completely converted to phases like SrCoO_3−δ, BaCeO₃, BaZrO₃, etc.     

A simultaneous,direct microwave/ultrasound-assisted digestion procedure for the determination of total Kjeldahl nitrogen

Simultaneous direct irradiation with microwaves and ultrasound was used to determine total Kjeldahl nitrogen. The method involves chemical digestion in two steps, mineralization with sulfuric acid and oxidation with H₂O₂. The most influential variables for the microwave/ultrasound (MW/US)-assisted digestion were optimized using tryptophan as the model substance. The optimum conditions were: H₂SO₄ volume, 10 mL; H₂O₂ volume, 5 mL; weight of sample, 0.05 g; MW power, 500 W; US power, 50 W; digestion time, 7 min (i.e., 5 min mineralization and 2 min oxidation). A modification of the classical Kjeldahl (Hach) method and an US-assisted digestion method were used for comparison. The latter was also optimized; the optimum conditions were: H₂SO₄ volume, 10 mL; H₂O₂ volume, 5 mL; sonication time with H₂SO₄, 15 min; sonication time with H₂O₂,10 min; US power, 50 W; weight of sample, 0.05 g. Five pure amino acids and two certified reference materials (NIST standard reference materials 1547 (peach leaves), and soil, NCS DC 73322) were analyzed to assess the accuracy of our new MW/US-assisted digestion method, that was successfully applied to five real samples. The significant reduction in digestion time (being 30 min and 25 min for classical Kjeldahl and US-assisted digestion methods, respectively) and consumption of reagents show that simultaneous and direct MW/US irradiation is a powerful and promising tool for low-pressure digestion of solid and liquid samples.