Investigation of II –VI alloy lattice dynamics by IR spectroscopic ellipsometry

Optical properties related to lattice vibrations of bulk Zn_1‐xBe_xSe, Zn_1‐x‐yBe_xMn_ySe and Cd_1‐xBe_xSe alloys are reported. Optical phonons of the mixed crystals grown by the Bridgman method have been investigated by infrared spectroscopic ellipsometry in the wave‐number range 300‐8000 cm^‐1. The complex dielectric functions can be reproduced using a model with two or three classical damped oscillators corresponding to the BeSe‐like transverse‐optical phonon‐modes and a Drude contribution from the free carriers. The frequencies of longitudinal‐optical phonons have been found from the imaginary parts of the dielectric loss functions. The influence of the alloy composition on the zone‐centre optical phonon frequencies is discussed. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Multimode phonon structure of Be‐containing II ‐ VI mixed crystals determined by IR spectroscopic ellipsometry

Spectroscopic ellipsometry in the infrared spectral range 250‐5000 cm^‐1 is used for analysis of the dielectric response of Zn_1‐x‐yBe_xMg_ySe and Zn_1‐x‐yBe_xMn_ySe crystals grown by a high‐pressure Bridgman method. Ellipsometric spectra display features in the spectral range 390‐500 cm^‐1 associated with BeSe‐type phonon modes. In the optical spectra of Zn_1‐x‐yBe_xMg_ySe crystals both BeSe‐type and MgSe‐type lattice absorption bands are detected. The MgSe‐like modes are located at approximately 300 cm^‐1. The complex dielectric functions can be reproduced using a model with two or three and one or two classical damped oscillators corresponding to the BeSe‐like and the MgSe‐like transverse‐optical phonon modes, respectively. The frequencies of longitudinal‐optical phonons have been derived from the dielectric loss functions. A red‐shift of the BeSe‐like phonons frequencies with a mean rate 0.42 cm^‐1 (0.50 cm^‐1) per mole percent of Mg (Mn) incorporated to the alloy has been found for examined concentration range x, y ≤ 0.25. A noticeable damping the intensities of BeSe‐type modes with increasing fraction of Mg and Mn dopant is observed in comparison to the strengths of BeSe‐type modes in Zn_1‐xBe_xSe crystals. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Fabrication and photocatalytic property of ZnO/SrTiO3 core/shell nanorod arrays

ZnO/SrTiO₃ core/shell nanorod arrays were fabricated by a facile two‐step method. ZnO nanorod arrays were first hydrothermally grown on Si substrate. Then, using liquid phase deposition method, SrTiO₃ were deposited onto the ZnO nanorods to form core/shell nanorod structures. The morphologies and structures of the products were characterized by scanning electron microscopy, transmission electron microscopy, and X‐ray diffraction. The photocatalytic behavior of the nanorod arrays was also examined through the photodegradation of methylene blue solution under UV irradiation. It was found that the core/shell nanorod arrays with deposition time of 10 min showed higher photocatalytic activity than bare ZnO nanorod arrays. This enhancement was attributed to the efficient charge separation at the ZnO/SrTiO₃ interface.     

Optical and magnetic properties of Nd‐doped ZnO nanoparticles

Nd‐doped ZnO nanoparticles with different concentration were synthesized by sol‐gel method. The structures, magnetic and optical properties of as‐synthesized nanorods were investigated. X‐ray diffraction (XRD) and x‐ray photoelectron spectroscopy (XPS) results demonstrated that Nd ions were incorporated into ZnO lattice; but Zn_1‐xNd_xO nanoparticles with Nd concentration of x = 0.05 showed Nd₂O₃ phase, so the saturation concentration of Nd in Zn_1‐xNd_xO is less than 5 at%. Vibrating sample magnetometer (VSM) measurements indicated that Nd doped ZnO possessed dilute ferromagnetis behaviour at room temperature. Photoluminescence spectroscopy (PL) showed that Nd ions doping induced a red slight shift and decrease in UV emission with increase of Nd concentration.     

Photoelectric and photothermal investigations of Zn1‐x‐yBexMnySe solid solutions

Zn_1‐x‐yBe_xMn_ySe solid solutions were grown from the melt by the high pressure Bridgman method. Optical, luminescence, photoelectric and photothermal properties of this material were investigated. Interpretation of the piezoelectrically detected photoacoustic spectra was performed using Jackson and Amer theory. From the spectral dependence of the amplitude and phase of photoacoustic signal as well as from photoluminescence spectra the variation of energy gap with composition was determined. The values of thermal diffusivity were derived from the dependence of photoacoustic signal on modulation frequency of the laser radiation illuminating the sample. The photoluminescence‐excitation spectra and photoconductivity spectra were measured. The origin of luminescence in Zn_1‐x‐yBe_xMn_ySe was discussed. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effect of rapid thermal annealing on Zn1‐xCdxO layers grown by radio‐frequency magnetron co‐sputtering

Zn_1‐xCd_xO layers were deposited on the sapphire substrate using the radio‐frequency magnetron co‐sputtering system. The grown Zn_1‐xCd_xO layers were carried out in the post‐annealing treatment for 1 min at the 800 °C oxygen‐ambient by the rapid thermal annealing (RTA) method. X‐ray diffraction (XRD) experiment shows that the Zn_1‐xCd_xO layers are changed from the single phase of the hexagonal structure at 0≤x ≤0.08 to the double phase of hexagonal‐and‐cubic structure at x =0.13. Thus, the maximum Cd‐composition ratio with the hexagonal structure was found out to be x =0.08. Also, the crystallinity of Zn_1‐xCd_xO layers at x =0.13 was remarkably improved by the RTA annealing treatment. This crystal quality improvement was thought to be associated with the relaxation of the compressive strain remaining in the Zn_1‐xCd_xO layers. Therefore, the results of XRD and transmittance lead that the crystal quality of the Zn_1‐xCd_xO layers forming the hexagonal ZnO phase is better than that forming the cubic CdO phase. Consequently, the reliable formation and the crystallinity of the Zn_1‐xCd_xO layers were achieved by using the RTA method of short‐time thermal‐annealing at the high temperature. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Experimental and first‐principle investigation of Cu‐doped ZnO ferromagnetic powders

Zn_1‐xCu_x O powders were synthesized by using sol‐gel method. Electronic band structure and ferromagnetic properties of Zn_1‐xCu_x O powders were studied experimentally and theoretically. The simulations are based upon the Perdew‐Burke‐Ernzerhof form of generalized gradient approximation within the density functional theory. Zn_1‐xCu_x O shows dilute ferromagnetism, as a saturated magnetization of 0.9×10^‐3emu/g was observed for Zn_0.95Cu_0.05O powders. The strong p ‐d hybridization between Cu and its four neighbouring O atoms is responsible for the ferromagnetism. Comparing with ZnO whose Fermi level locates at the valence band maximum, the Fermi level of the Zn_1‐xCu_x O shifts upward into the valence band and hence the Zn_1‐xCu_x O system exhibits theoretically a p ‐type metallic semiconducting property. The Zn_1‐xCu_x O system may be a potential candidate in spintronics. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

A study on structural formation and optical property of wide band-gap Be0.2Zn0.8O layers grown by RF magnetron co-sputtering system

Wide band-gap BeZnO layers were grown on Al₂O₃ (0 0 0 1) substrate using radio-frequency magnetron co-sputtering. The rate of Be_xZn_1−xO crystallized as a hexagonal structure was x=0.2. From the X-ray photoelectron spectroscopy measurement, the O–Zn bonds relating the crystal structure and the Be–O bonds related to the deviation of the stoichiometry in the BeZnO layer were caught at 530.4 and 531.7 eV in the O 1s spectrum, respectively. Thus, the observance on the Be 1s peak of 113.2 eV associated with the bonding Be–O indicates that the sputtered Be atoms are substituted for the host-lattice site in ZnO. This Be–O bonding shows a relatively low intense and broadening spectrum caused by large fluctuation of Be content in the BeZnO layer. From the photoluminescence and transmittance measurement, the free exciton and the neutral donor-bound exciton (D⁰, X) emissions were observed at 3.7692 and 3.7313 eV, respectively, and an average transmittance rate over 95% was achieved in a wide ultraviolet (UV)–visible region. Also, the binding energy for the (D⁰, X) emission was extracted to be 37.9 meV. Through the wide band-gap material BeZnO, we may open some possibilities for fabricating a ZnO-based UV light-emitting diode to be utilized as a barrier layer comprised of the ZnO/BeZnO quantum well structure and/or an UV light emitting material itself.     

The effect of ZnO buffer layer on structural and optical properties of ZnO nanorods

A low‐temperature synthetic route was used to prepare oriented arrays of ZnO nanorods on ITO conducting glass substrate coated with buffer layer of ZnO seeds in an aqueous solution. The corresponding growth behavior and optical properties of ZnO nanorod arrays were studied. It was found that the nature of the buffer layer had effect on the microstructures and optical properties of the resultant ZnO nanorod arrays. X‐ray diffraction (XRD) results showed the nanorods were preferentially grown along (002) direction, but the diameter of the nanorods prepared with the buffer layer was much smaller than the without one, which can be clearly seen from the scanning electron microscopy (SEM) results. And it also found that the buffer layer was not only enhanced the density of overall coverage but also beneficial to grown the oriented arrays. Photoluminescence spectroscopy (PL) results indicated that the all the samples had the better optical behaviors. By computation, the relative PL intensity ratio of ultraviolet emission (I_UV) to deep level emission (I_DLE) of ZnO nanorods grown with the pure substrate was much higher than that of the sample with the buffer layer. The defects on the surface increased with the size reduction of nanorods caused by the buffer layer may be the main reason for it. And the small shift in the UV emission was caused by the rapid reduction in crystal size and compressive stress from Raman spectra results. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structure and optical properties of Mg‐doped ZnO nanoparticles by polyacrylamide method

Mg‐doped ZnO (Mg_xZn_1‐xO) nanoparticles with precise stoichiometry are synthesized through polyacrylamide polymer method. Calcination of the polymer precursor at 650 °C gives particles of the homogeneous solid solution of the (Mg_xZn_1‐xO) system in the composition range (x < 0.15). ZnO doping with Mg causes shrinkage of lattice parameter c. The synthesized Mg_xZn_1‐xO nanoparticles are typically with the diameter of 70–85 nm. Blue shift of band gap with the Mg‐content is demonstrated, and photoluminescence (PL) from ZnO has been found to be tunable in a wide range from green to blue through Mg doping. The blue‐related PL therefore appeared to be caused by energetic shifts of the valence band and/or the conduction band of ZnO. Mg_xZn_1‐xO nanoparticles synthesized by polyacrylamide‐gel method after modified by polyethylene glycol surfactant have a remarkable improvement of stability in the ethanol solvent, indicating that these MZO nanoparticles could be considered as the candidate for the application of solution–processed technologies for optoelectronics at ambient temperature conditions.     

Structure and electrical properties of Mg‐doped ZnO nanoparticles

Mg_xZn_1‐xO (x=0.01‐0.3) nanoparticles were synthesized by the sol‐gel technique using solutions of Mg and Zn based organometalic compounds. The electrical properties of Mg doped zinc oxide (ZnO) were studied within wide temperature range from 300 to 500 K under the N₂ gas flow (flow rate: 20 sccm) and in the frequency range from 40 Hz to 1 MHz for ac electrical measurements. The dc conductivities and the activation energies were found to be in the range of 10^‐9‐10^‐6 S/cm at the room temperature and 0.26‐0.86 eV respectively depending on doping rate of these samples. The ac conductivity was well represented by the power law Aω^s. The conduction mechanism for all doped ZnO could be related to correlated barrier hopping (CBH) model. The complex impedance plots (Nyquist plot) showed the data points lying on a single semicircle, implying the response originated from a single capacitive element corresponding to the nanoparticle grains. The crystal structures of the Mg_xZn_1‐xO nanoparticles were characterized using X‐ray diffraction. The calculated average particle sizes values of Zn_1‐xMg_xO samples are found between 29.72 and 22.43 nm using the Sherrer equation. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Co nanoclusters as origin of ferromagnetism in sol‐gel synthesized Zn1‐xCoxO (x = 0.05, 0.10 and 0.15) samples

We report on the structural and magnetic properties of the polycrystalline samples of Zn_1‐xCo_xO (x = 0.05, 0.10 and 0.15) synthesized via sol‐gel route. The air sintered samples of all compositions exhibit paramagnetic behaviour at room temperature, on the other hand the same samples on annealing in Ar/H₂ atmosphere show room temperature ferromagnetism (RTFM) with enhanced magnetization. The value of magnetization increases with the Co concentration (x) in both the air sintered and Ar/H₂ annealed samples. The observed ferromagnetism in the Ar/H₂ annealed Zn_1‐xCo_xO (x = 0.05, 0.10 and 0.15) samples is attributed to the presence of Co nanoclusters as detected by XRD and FESEM‐EDAX. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Decisive role of Au layer on the oriented growth of ZnO nanorod arrays via a simple aqueous solution method

Vertically aligned arrays of ZnO nanorod were synthesized on the Au/SiO₂/Si(1 0 0) substrate by a simple aqueous solution growth process, without pre-prepared ZnO seed layer. For comparison, glass and SiO₂/Si were also used as substrates, and the results show that the Au layer plays a decisive role in orienting the growth of the ZnO nanorod. The effects of other growth parameters, including Zn²⁺ concentration and growth time, on morphology, density, and orientation of the ZnO nanostructure were also studied and with longer reaction time, a new structure namely ZnO nanotip was obtained. Moreover, the growth mechanism of ZnO nanorod arrays grown on the Au/SiO₂/Si substrate was proposed.     

In2O3 nanorod arrays grown at grain-boundary triple junctions of Cu–Sn alloy substrate

In this article, an alternative method for site-specific growth of In₂O₃ nanorod arrays, which relies on the vapor–liquid–solid growth mechanism, is demonstrated using Cu–Sn (5 at% Sn) alloy as substrate. By annealing Cu–Sn alloy slightly below the solidus line, grain-boundary triple junctions can be wetted preferentially. As a result, the catalyzing Cu droplets will be present at the sites of grain-boundary triple junctions, which will control the growth of In₂O₃ nanorods at defined locations. This growth technique provides a cost-effective and simple approach to fabricate ordered nanorod arrays with the sites controlled, which may benefit nanorod device applications.     

Morphological control of MgxZn1−xO layers grown on Ga:ZnO/glass substrates for photovoltaics

Mg_xZn_1?xO has been used in various photovoltaic cells because its energy bandgap can be tailored by controlling the Mg composition in this ternary compound. The Mg_xZn_1?xO layers with different surface morphologies including two-dimensional (2-D) films and one-dimensional (1-D) nanostructures are preferred for conventional p–n junction solar cells and polymer–inorganic hybrid solar cells, respectively. The Mg_xZn_1?xO layers are sequentially grown on Ga-doped ZnO (GZO) transparent conductive electrode using metalorganic chemical vapor deposition (MOCVD). The effect of the buffer layers on Mg_xZn_1?xO surface morphology is investigated. It is observed that Mg_xZn_1?xO deposited at ～500 °C on a low-temperature (～250 °C) ZnO buffer layer is in the form of 2-D dense and smooth films, whereas, on a high-temperature (～520 °C) ZnO buffer layer is in the form of 1-D nanostructures. Based on the structure characterization results, a growth mechanism in terms of nucleation and texturing is proposed to explain the buffer layer effect.     

Paramagnetic behavior of Zn1−xMnxO at room temperature

Mn‐doped ZnO were synthesized by solid state reaction and sol‐gel method respectively. It was found that samples synthesized by solid state reaction containing Mn₂O₃ and MnO₂ are a mixture of ferromagnetic and paramagnetic phases. Contrary, samples without second phases were found to be paramagnetic at room temperature. According to previous report, interface effects between Zn‐rich Mn₂O₃ and MnO₂ interfaces may be the origin of the ferromagnetic behavior observed in our samples prepared by solid reaction, so the alloy of Zn_1−xMn_xO may be paramagnetic at room temperature. Prepared by sol‐gel technique, the samples without second phases in the XRD patterns are also room‐temperature paramagnetic. Therefore we believe that the magnetism of Zn_1−xMn_xO is paramagnetic at room temperature. (© 2008 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Lightweight Ti–Zr–Be–Al bulk metallic glasses with improved glass-forming ability and compressive plasticity

A series of lightweight Ti–Zr–Be–Al bulk metallic glasses (BMGs) have been developed through the addition of Al to Ti–Zr–Be ternary glassy alloy. By replacing Be with Al, the critical size of the glassy rod has been increased from 5 mm for Ti₄₁Zr₂₅Be₃₄ alloy to 7 mm for Ti₄₁Zr₂₅Be₂₉Al₅ alloy, while the yield strength of Ti₄₁Zr₂₅Be_34 ? xAl_x (x = 2–10) has been greatly enhanced, resulting in a significant increase of the specific strength which is defined as yield strength/density. Among these newly developed Ti–Zr–Be–Al BMGs, Ti₄₁Zr₂₅Be₂₆Al₈ glassy alloy exhibits a high specific strength of 4.33 × 10⁵ Nm/kg and a very large compressive plastic strain of 47.0%, which are much larger than those (3.69 × 10⁵ Nm/kg and 2.9%, respectively) for Ti₄₁Zr₂₅Be₃₄ glassy alloy. The present results show that Al is an effective alloying element for improving the glass-forming ability (GFA) and mechanical properties of Ti-Zr-Be glassy alloy.     

Solvothermal controlled growth of Zn-doped SnO2 branched nanorod clusters

Branched Zn-doped SnO₂ nanorod clusters with tunable size and aspect ratios were prepared by a facile solvothermal process. The introduction of a small quantity of Zn²⁺ proved to play an important role in directing the anisotropic growth of SnO₂ nanocrystals. The as-synthesized products exhibit tetragonal rutile structure and many lattice defects exist in the products. The possible growth mechanism has been proposed. These Zn-doped SnO₂ nanorods exhibited unique Raman spectrum in contrast with the undoped SnO₂ nanostructures. These Zn-doped SnO₂ nanorods showed good sensitivities to ethanol gas, acetone gas, and benzene gas.     

Structural and optical properties of Zn(Mg,Cd)O alloy films grown by remote-plasma-enhanced MOCVD

We report the structural and optical properties of wurtzite-structure Zn(Mg,Cd)O ternary alloys. Wurtzite (0 0 0 1) Zn_1−xCd_xO and Mg_yZn_1−yO films were grown on (11–20) sapphire substrates using remote-plasma-enhanced metalorganic chemical vapor deposition. The large bowing parameters of Zn_1−xCd_xO and Mg_yZn_1−yO ternary alloys are 3.0 and 3.5, respectively, which reflects the large difference of each binary’s electronegativity. We have analyzed the broadening of photoluminescence (PL) in Zn(Mg,Cd)O alloys on alloy content by taking into account the statistical alloy fluctuation and the localization of the exciton, and have clarified that the localization of the exciton strongly affects to PL full-width at half-maximum (FWHM) in Zn(Mg,Cd)O alloys. The alloy broadenings in steady-state PL of Zn(Mg,Cd)O alloys are in good agreement with the calculated tendency by the theoretical model based on the statistical alloy fluctuation, while PL FWHM of Zn_1−xCd_xO is three times larger than the calculated results. Moreover, as another way to confirm alloy broadening, we also have done time-resolved PL measurements and derived the localized depth of the exciton in ZnO-based system, indicating a good agreement with the tendency of PL FWHM broadening.     

Effects of post-annealing temperature on structural,optical, and electrical properties of MgxZn1−xO films by RF magnetron sputtering

Mg_xZn_1?xO thin films were deposited on quartz substrates by RF magnetron sputtering. The effect of post-annealing temperature on structural, optical, and electrical properties was investigated with the annealing temperatures increasing from 450 to 750 °C. The crystallinity of Mg_xZn_1?xO film annealed at 650 °C was significantly improved while the film annealed at 750 °C showed little improvement. The electrical properties degraded with the increase of annealing temperature. The annealing temperature seemed to impact the E_g value of Mg_xZn_1?xO thin films because of the variation of carrier concentration.