Physico-chemical applications of liquid chromatography I. Investigation of the adsorption of cardiac glycosides from water-ethanol solutions on silanized silica

Summary Using the cardiac glycoside cymarin as the example the application of liquid chromatography for the study of adsorption from solutions and the determination of the corresponding thermodynamic characteristics was investigated. The adsorption isotherm of cymarin at small concentrations from a water-ethanol solvent on silica gel modified by dimethyldichlorosilane was measured under static conditions using analytical LC to determine the concentrations of solutions after adsorption. The values of the Henry constants were obtained by extrapolating the slope of the adsorption isotherm down to zero concentration. The specific retention volumes for different but small sample sizes of cymarin in the chromatographic column were measured, the adsorbent and the water-ethanol eluent being the same as in the static conditions. The specific retention volume for a small (zero) sample size determined by liquid chromatography experiment coincides with the Henry constant of cymarin adsorption determined in static conditions. In favourable cases liquid chromatography can be used to determine the equilibrium constants for adsorption from solution. The dependence of the Henry constants on temperature was investigated for several cardiac glycosides. The influence of the modification of the adsorbent surface on the separation of the cardiac glycosides was also studied.     

Study of adsorption from solutions by frontal chromatography

Summary The automatic frontal chromatography installation was described. By this chromatographic method the adsorption isotherm of benzene from n-heptane solutions on hydroxylated surface of silica with various porosity has been determined. This investigation was performed at different flow rates of eluent and in a wide range of concentrations. The isotherm of adsorption obtained by this chromatographic method has been compared with the results of the static measurements. The coincidence of adsorption isotherms measured at the various flow rates are shown to be a criterion of proximity the chromatographic process to the equilibrium.     

Synthesis of Chlorogenic Acid Imprinted Chromatographic Packing by Surface-initiated Atom Transfer Radical Polymerization and Its Application

A novel chromatographic packing of chlorogenic acid（CGA） molecularly imprinted polymer（MIP） based on the 5.0 ~tm silica was prepared by surface initiated atom transfer radical polymerization（SI-ATRP） with 4-vinylpyridine（4-VP） as functional monomer, ethyl glycol dimethacrylate（EDMA） as cross-linker in the mixture of methanol and water（7：3, volume ratio） under mild reaction conditions. The characteristics of CGA MIP were investi- gated by elemental analysis, thermogravimetric analysis（TGA）, Fourier transform infrared spectrometry（FTIR） and atomic force microscopy（AFM）. The effects of some chromatographic conditions such as mobile phase composition and temperature on the retention time were investigated. The adsorption capacity of the stationary phase for com- pounds was determined by frontal chromatographic technique. The results show that Freundlich isotherm fits the ex- perimental adsorption isotherm data better than Langmuir model does. The relatively high heterogeneity index values regressed with the Freundlich isotherm suggest the formation of fairly homogeneous MIP. Thermodynamic data（AAH and AAS） obtained by van＇t Hoff plots reveal an entropy-controlled separation. The CGA MIP column was shown to be successful for the separation and purification of chlorogenic acid from the extract of Honeysuckle.     

Optimal determination of steric mass action model parameters for β-lactoglobulin using static batch experiments

In this work, parameters of the steric mass-formalism SMA are optimally ascertained for a reliable determination of the adsorption isotherms of β-lactoglobulin A and B under non-isocratic conditions. For this purpose, static batch experiments are used in contrast to the protocols based on different experimental steps, which use a chromatographic column. It is shown that parameters can already be determined for a small number of experiments by using a systematic procedure based on optimal model-based experimental design and an efficient NLP-solver. The in different works observed anti-Langmuir shape of the isotherm for small concentrations of β-lactoglobulin A was corroborated. Moreover, we also found indications for a porosity variation with changing protein concentrations.     

Determination of adsorption isotherms of proteins by H-root method: comparison between open micro-channels and conventional packed columns

This communication compares the accuracy of a micro open parallel plate system (microOPPS) with a conventional packed column for predicting isotherm data by using the H-root method (HRM). HRM is restricted to compounds obeying the Langmuir isotherm model. The performance of the two chromatographic systems was simulated by using comprehensive mathematical models. Operating conditions were varied and their effects on the accuracy of predictions was evaluated. Better accuracy in the isotherm predictions was obtained with the packed column due to its higher efficiency. However, good predictions can be obtained with the microOPPS with the advantage of significantly lower sample consumption.     

Determination of the lumped mass transfer rate coefficient by frontal analysis

The validity of measurements of the lumped mass transfer rate coefficient (k_m,L) is studied on the basis of experimental data acquired under Langmuir isotherm conditions, in reversed-phase liquid chromatography. Two different methods were used, the perturbation method and frontal analysis. Accurate values of k_m,L can be properly obtained by the perturbation method because, with this method, the chromatographic processes take place under locally linear isotherm conditions. Values of k_m,L can also be derived from the breakthrough curves obtained in frontal analysis. Because the contribution of axial dispersion to band broadening was larger than that of the mass transfer resistances, the apparent axial dispersion coefficient (D_a) was first derived from the breakthrough curve by applying the equilibrium–dispersive model. Then, the value of k_m,L was calculated from D_a. The values of k_m,L determined by the two methods were in close agreement in the range of nondimensional Langmuir equilibrium constants (r=1/[1+K_LC₀]) between 0.32 and 0.85, irrespective of the mobile phase flow velocity. Thus, frontal analysis can be used for kinetic studies of the mass transfer in chromatographic columns.     

A predictive approach to correlating protein adsorption isotherms on ion-exchange media

The equilibrium adsorption of three small basic proteins was measured on cation exchangers under various solution conditions and was used as the basis for developing a predictive approach for correlating adsorption behavior. A mechanistically based isotherm model is used to model the equilibrium adsorption so as to facilitate isotherm prediction using minimal experimental data. The model explicitly considers the contributions of protein-surface and protein-protein interactions, and decoupling them allows each to be correlated with different experimental measurements. Specifically, protein-surface interactions are related to chromatographic data in the form of the isocratic retention factor (k'), while protein-protein interactions are analyzed on the basis of high-coverage isotherm data on an arbitrary stationary phase. Analysis of experimental data within this framework reveals a high level of consistency. The model is also used to facilitate prediction of adsorption isotherms on other ion-exchange media using isotherms on one adsorbent.     

质粒DNA在灌注色谱基质上的吸附行为

Anion exchange chromatography is the most popular chromatographic method for plasmid separation.POROS R1 50 is a perfusio n chro mato graphic suppo rt w hich is a reversed phase matrix and is an alternative to co nventio nal o nes due to its mass transfer pro perties.The adso rptio n and elutio n o f the pIDKE2 plasmid o nto reversed phase POROS R1 50 w as studied.Langmuir iso therm mo del w as adjusted in o rder to get the max imum adso rptio n capacity and the disso ciatio n co nstant fo r POROS R1 50-plasmid DNA(pDNA) system.Breakthro ugh curves w ere o btained fo r vo lumetric flo w s betw een 0.69-3.33 mL/min,given dynamic capacity up to 2.3 times higher than tho se repo rted fo r io nic ex change matrix used during the purificatio n pro cess o f plasmids w ith similar size to that o f pIDKE2.The efficiency w as less than 45% fo r the flo w co nditio ns and initial co ncentratio n studied,w hich means that the suppo rt w ill no t be o perated under saturatio n circumstances.     

酚醛型吸附树脂在非水体系中对吡啶和N,N-二甲基苯胺的吸附性能研究

研究了酚醛型吸附树脂JDW 2在非水体系中对吡啶和N ,N 二甲基苯胺的静态吸附 .由实验结果推论正己烷中树脂对吡啶和N ,N 二甲基苯胺的吸附是以氢键吸附机理为主进行的 ,JDW 2酚醛型吸附树脂在正己烷中 ,等温吸附吡啶和N ,N 二甲基苯胺的平衡吸附数据符合Langmuir方程 ,相关系数在 0 99以上 ,因此 ,酚醛型吸附树脂在正己烷中吸附吡啶和N ,N 二甲基苯胺属单分子层吸附 ;同时对非水体系中乙醇或乙酸乙酯的含量对树脂吸附吡啶和N ,N 二甲基苯胺的影响进行了研究     

酚醛型吸附树脂对水体系中吡啶和N,N-二甲基苯胺的吸附性能研究

研究了酚醛型吸附树脂在水体系中对吡啶和N，N-二甲基苯胺的静态和动态吸附行为．结果表明，在水中树脂对吡啶和N，N-二甲基苯胺的吸附主要以疏水吸附机理进行；吸附吡啶和N．N-二甲基苯胺的初始阶段，即达到38．3～48．9％平衡吸附时，吸附速率数据和半经验速率方程很吻合：酚醛型吸附树脂等温吸附吡啶和N，N-二甲基苯胺的平衡吸附数据符合Langmuir方程，相关系数在0．99以上，酚醛型吸附树脂吸附吡啶和N，N-二甲基苯胺属单分子层吸附：用80％的乙醇溶液作洗脱剂来洗脱吸附吡啶已达饱和的JDW-2树脂，效果是很理想的．在3．6个床体积内洗脱率达91．52％，4．8个床体积内洗脱率达到94．85％。表明酚醛型吸附树脂具有优良的洗脱性能．     

Modeling of adsorption in hydrophobic interaction chromatography systems using a preferential interaction quadratic isotherm

A preferential interaction quadratic isotherm model for hydrophobic interaction chromatographic systems is presented in this paper. In this isotherm, the nonlinear effect of salt on the capacity factor is described using the preferential interaction model developed by Perkins et al. [J. Chromatogr. A, 766 (1997) 1]. This is then coupled with a quadratic nonlinear isotherm to describe nonlinear adsorption behavior at high solute concentrations. The resulting preferential interaction quadratic isotherm is examined for its ability to describe solute adsorption behavior under both linear and nonlinear conditions over a wide range of salt concentrations in HIC systems. The results indicate that this isotherm is well suited for predicting nonlinear adsorption behavior in HIC systems for both proteins and low-molecular mass HIC displacers.     

Residual solvents determination in the antibiotic L-749,345 by static headspace gas chromatography

An automated static headspace gas chromatographic method for the determination of residual solvents in the antibiotic L-749,345 was developed and validated. Headspace analysis was used when direct injection of the compound was found to significantly degrade the performance of the column stationary phase. Quantitation was performed by external standard analyses and the method was found to be precise, linear, sensitive, accurate and rugged. The chromatographic conditions and headspace parameters were optimized in a separate experiment to provide a limit test for trace levels of methylene chloride in the presence of significant levels of ethanol.     

Determination of the heat effects involved during toluene vapor adsorption and desorption from microporous activated carbon

In the present work the adsorption of toluene on microporous activated carbon was chosen as an illustrative example in order to show that different values of the heat effect might be obtained following the procedure used. Values ranging from 85 to 40 KJ/moL were obtained for the isosteric heat of adsorption at different adsorbate loadings using adsorption isotherm data measured under static conditions. However, the application of temperature programmed desorption (TPD) experiments carried out under dynamic conditions yields apparent energy of desorption values that cannot be systematically correlated with the heat of adsorption which is a thermodynamic parameter relevant to the adsorption equilibrium. This issue is of interest because the use of accurate values of the heat of adsorption is important for the correct designing and operating of adsorption facilities.     

Study of hydrophobic interaction adsorption of bovine serum albumin under overloaded conditions using flow microcalorimetry

The adsorption behavior of bovine serum albumin (BSA) on a Sepharose based hydrophobic interaction support has been studied. Flow microcalorimetry has been used to determine the heat of adsorption under overloaded chromatographic conditions. These data have been complemented with capacity factor and isotherm measurements to provide insight on the mechanisms of adsorption. The heat of adsorption data have confirmed that the hydrophobic interaction adsorption of BSA under linear isotherm conditions is driven by entropy changes. Under overloaded (non-linear) conditions, however, it has been shown that the changes in enthalpy can drive adsorption; this behavior is not evident from analyses of capacity factor data. It is postulated that for BSA adsorption on the Sepharose derivative of interest, attractive force interactions between adsorbed protein molecules drive the adsorption process under overloaded conditions in a high (NH4)2SO4 environment. It is further postulated that these interactions are due to a change in confirmation of the adsorbed protein under these conditions.     

Influence of pressure on the chromatographic behavior of insulin variants under nonlinear conditions

The effect of pressure on the chromatographic behavior of two insulin variants in RPLC was investigated on a YMC-ODS C18 column, under nonlinear conditions. The adsorption isotherm data of porcine insulin and Lispro were measured at average column pressures ranging from 52 to 242 bar. These data fit well to the Toth and the bi-Langmuir isotherm models. The saturation capacity increases rapidly with increasing pressure while the affinity (or equilibrium) constant and the parameter characterizing the surface heterogeneity decrease. It is noteworthy that the distribution coefficient of the insulin variants increases with increasing pressure whereas their equilibrium constant b decreases for porcine insulin and increases for Lispro. The association constant b(ds), which characterizes the adsorption and desorption equilibrium of insulin in the system, increases with increasing pressure. The excellent agreement between the experimental overloaded profiles recorded under different pressures and those calculated using the POR model suggests that the chromatographic behavior of insulin is controlled more by equilibrium thermodynamics than by the mass transfer kinetics. The latter seems to be nearly independent of the average column pressure. Thus, increasing the average column pressure is an efficient, albeit costly, way to increase the loading capacity of the column, hence the production rate in preparative chromatography.     

Determination of competitive adsorption isotherms applying the nonlinear frequency response method: Part II. Experimental demonstration

This paper demonstrates an experimental application of the nonlinear frequency response (FR) method extension to determine adsorption isotherms of binary mixtures. This method, based on the analysis of the response of a chromatographic column subjected to the sinusoidal inlet concentration changes, is shown to be an alternative for isotherm determination. The critical issue related to the successful application of the method is to reach experimentally the low frequency asymptotic behaviour of the corresponding frequency response functions (FRFs). Although, there are different possibilities to perform periodical inlet concentration changes, in this paper only simultaneous changes for both components were considered. The adsorption of phenol and 2-phenylethanol on octadecyl silica was analyzed experimentally using a mixture of methanol and water as a solvent. Parameters of competitive isotherms were also estimated for comparison using the classical perturbation method. Despite certain differences between competitive isotherms estimated with the two methods that were found, the obtained results show the potential of the nonlinear FR method for measuring competitive isotherms.     

Determination of competitive adsorption isotherms applying the nonlinear frequency response method: Part I. Theoretical analysis

In this work adsorption equilibria of binary mixtures are quantified analyzing the nonlinear frequency response of a chromatographic column. Local partial derivatives of an isotherm model can be estimated for certain steady-states from the low frequency asymptotes of the corresponding frequency response functions (FRFs). The required FRFs correspond to two different compounds and the type of the imposed inlet concentration changes, e.g. periodical inlet concentration changes of only one compound or of both of them. For an accurate determination of isotherm parameters, it is necessary to approach as close as possible the low frequency asymptotic behaviour of these functions. Based on principles valid for the FRFs corresponding to the adsorption of a single solute, frequencies needed to reach the low frequency asymptotes of the functions of interest for estimating competitive isotherms are defined in this paper. The relation between the accuracy of the isotherm parameters determined and numbers and types of periodical inlet concentration changes and steady-states analyzed is also evaluated.     

Electrical double layer and adsorption of iodide ions at the Bi | acetonitrile interface

The adsorption of I^? ions on the Bi(111) single crystal plane from solutions in acetonitrile has been investigated by impedance measurement method. The ionic charge due to the specific adsorption has been obtained using the mixed electrolyte method applied for both electrode charge and electrode potential as the independent electrical variables. The Gibbs energy of ions adsorption has been calculated using the virial adsorption isotherm. It was found that under comparable conditions the results obtained at constant electrode potential and at constant electrode charge are coincident and the Gibbs energy of I^? anion adsorption increases in the sequence of solvents: methanol < ethanol < propylene carbonate < acetonitrile. The electrosorption valency has been calculated and it was found that this parameter increases in the sequence propylene carbonate < ethanol < methanol < acetonitrile.     

Effect of Mobile Phase Components on the Separation of Polypeptides Using Carbon Dioxide-Based Mobile Phases

The effect of mobile phase modifier and additive on the chromatographic properties of various small polypeptides was explored under subcritical conditions. A polymeric column was used to separate various enkephalin analogs, bradykinin, and oxytocin using a carbon dioxide-based mobile phase with either an ethanol or a 2-methoxyethanol modifier. The role of the modifier was found to be secondary to that of the mobile phase additive. As progressively stronger acidic mobile phase additives were used, the peak profiles of the various polypeptides improved and retention decreased. Heptadecafluorooctanesulfonic acid was found to be the most useful additive for these types of solutes under near-critical conditions, while the potassium salt of heptadecafluorooctanesulfonic acid failed to elute any of the polypeptides. At low temperatures, pressure gradients with a carbon dioxide/ethanol/heptadecafluorooctanesulfonic acid ternary mobile phase produced reasonably good peak profiles with the polymeric column.