Analysis on vibration characteristics of large-size rectangular piezoelectric composite plate based on quasi-periodic phononic crystal structure

Based on the theory of composite materials and phononic crystals (PCs), a large-size rectangular piezoelectric composite plate with the quasi-periodic PC structure composed of PZT-4 and epoxy is proposed in this paper. This PC structure can suppress the transverse vibration of the piezoelectric composite plate so that the thickness mode is purer and the thickness vibration amplitude is more uniform. Firstly, the vibration of the model is analyzed theoretically, the electromechanical equivalent circuit diagram of three-dimensional coupled vibration is established, and the resonance frequency equation is derived. The effects of the length, width, and thickness of the piezoelectric composite plate at the resonant frequency are obtained by the analytical method and the finite element method, the effective electromechanical coupling coefficient is also analyzed. The results show that the resonant frequency can be changed regularly and the electromechanical conversion can be improved by adjusting the size of the rectangular piezoelectric plate. The effect of the volume fraction of the scatterer on the resonant frequency in the thickness direction is studied by the finite element method. The band gap in X and Y directions of large-size rectangular piezoelectric plate with quasi-periodic PC structures are calculated. The results show that the theoretical results are in good agreement with the simulation results. When the resonance frequency is in the band gap, the decoupling phenomenon occurs, and then the vibration mode in the thickness direction is purer.     

Investigations of thickness-shear mode elastic constant and damping of shunted piezoelectric materials with a coupling resonator

Shear-mode piezoelectric materials have been widely used to shunt the damping of vibrations where utilizing surface or interface shear stresses. The thick-shear mode(TSM) elastic constant and the mechanical loss factor can change correspondingly when piezoelectric materials are shunted to different electrical circuits. This phenomenon makes it possible to control the performance of a shear-mode piezoelectric damping system through designing the shunt circuit. However, due to the difficulties in directly measuring the TSM elastic constant and the mechanical loss factor of piezoelectric materials, the relationships between those parameters and the shunt circuits have rarely been investigated. In this paper, a coupling TSM electro–mechanical resonant system is proposed to indirectly measure the variations of the TSM elastic constant and the mechanical loss factor of piezoelectric materials. The main idea is to transform the variations of the TSM elastic constant and the mechanical loss factor into the changes of the easily observed resonant frequency and electrical quality factor of the coupling electro–mechanical resonator. Based on this model, the formular relationships are set up theoretically with Mason equivalent circuit method and they are validated with finite element(FE) analyses. Finally, a prototype of the coupling electro–mechanical resonator is fabricated with two shear-mode PZT5 A plates to investigate the TSM elastic constants and the mechanical loss factors of different circuit-shunted cases of the piezoelectric plate. Both the resonant frequency shifts and the bandwidth changes observed in experiments are in good consistence with the theoretical and FE analyses under the same shunt conditions. The proposed coupling resonator and the obtained relationships are validated with but not limited to PZT5 A.     

Multimode shunt damping of piezoelectric smart panel for noise reduction

Multimode shunt damping of piezoelectric smart panel is studied for noise reduction. Piezoelectric smart panel is a plate structure on which a piezoelectric patch is attached with an electrical shunt circuit. When an incidence sound is impinged on the panel structure, the structure vibrates and the attached piezoelectric patch produces an electrical energy, which can be effectively dissipated as heat via the electrical shunt circuit. Since the energy dissipation strongly depends on the vibration mode of the panel structure, many patches are required for multiple vibration modes. Instead of using multiple piezoelectric patches, a single piezoelectric patch is used in conjunction with a blocked shunt circuit for multimode shunt damping. Modeling, shunt parameter tuning, and implementation of the blocked shunt circuit along with an acoustic test of the panel are explained. A remarkable reduction of the transmitted noise was achieved for multiple modes of the panel. Since this technology has many merits in terms of compactness, low cost, robustness, and ease of installation, practical applications in many noise problems can be anticipated.     

LCR分流电路下压电声子晶体智能材料的带隙

将带有LCR分流电路的压电陶瓷片对贴在铝和环氧树脂组成的声子晶体结构中.使智能材料的机械振动与压电陶瓷的压电效应耦合起来,推导出机械振动在压电陶瓷片上的等效附加应力;使LCR分流电路中的电磁振荡效应和声子晶体的能带特性有机结合,计算了在分流电路作用下智能材料扭转和弯曲振动的带隙特性,研究了电阻、电感、电容元件的改变对压电声子晶体智能材料带隙的影响.研究结果表明:在合理尺寸下,随着分流电路中电阻值的增大,带隙的频率范围变宽,但衰减幅值有所降低;电感和电容值的增大都可以使带隙向低频移动,带隙的衰减幅值随着电感值的增大而升高,但随着电容值的增大而降低.从而给压电声子晶体智能材料减震降噪的控制提供了一种新思路.     

Finite element reduced order model for noise and vibration reduction of double sandwich panels using shunted piezoelectric patches

This work concerns the control of sound transmission through double laminated panels with viscoelastic core using semi-passive piezoelectric shunt technique. More specifically, the system consists of two laminated walls, each one composed of three layers and called sandwich panel with an air cavity in between. The external sandwich panel has a surface-mounted piezoelectric patches. The piezoelectric elements, connected with resonant shunt circuits, are used for the vibration damping of some specific resonance frequencies of the coupled system. Firstly, a finite element formulation of the fully coupled visco-electro-mechanical-acoustic system is presented. This formulation takes into account the frequency dependence of the viscoelastic material. A modal reduction approach is then proposed to solve the problem at a lower cost. In the proposed technique, the coupled system is solved by projecting the mechanical displacement unknown on a truncated basis composed by the first real short-circuit structural normal modes and the pressure unknown on a truncated basis composed by the first acoustic modes with rigid boundaries conditions. The few initial electrical unknowns are kept in the reduced system. A static correction is also introduced in order to take into account the effect of higher modes. Various results are presented in order to validate and illustrate the efficiency of the proposed finite element reduced order formulation.     

Essentially nonlinear piezoelectric shunt circuits applied to mistuned bladed disks

An essentially nonlinear piezoelectric shunt circuit is proposed for the practical realization of nonlinear energy sink, and then applied to a mistuned bladed disk for blade vibration reduction. First, the global dynamics of a single degree-of-freedom linear mechanical oscillator, coupled to an essentially nonlinear shunted piezoelectric attachment, is studied. Under certain conditions, the nonlinear targeted energy transfer, i.e. a fast, passive energy transfer from the mechanical oscillator to the nonlinear attachment is observed. A numerical method, referred to as the variable-coefficient harmonic balance method, is developed to calculate quasi-periodic responses arising in the electromechanical system under harmonic forcing. Characterized by the nonexistence of a resonance frequency, the essentially nonlinear shunt circuit is able to work robustly over a broad frequency band with a smaller inductance requirement compared with the linear resonant shunt circuit.     

Flexural wave band-gaps in phononic metamaterial beam with hybrid shunting circuits

Periodic arrays of hybrid-shunted piezoelectric patches are used to control the band-gaps of phononic metamaterial beams. Passive resistive-inductive(RL) shunting circuits can produce a narrow resonant band-gap(RG), and active negative capacitive(NC) shunting circuits can broaden the Bragg band-gaps(BGs). In this article, active NC shunting circuits and passive resonant RL shunting circuits are connected to the same piezoelectric patches in parallel, which are usually called hybrid shunting circuits, to control the location and the extent of the band-gaps. A super-wide coupled band-gap is generated when the coupling between RG and the BG occurs. The attenuation constant of the infinite periodic structure is predicted by the transfer matrix method, which is compared with the vibration transmittance of a finite periodic structure calculated by the finite element method. Numerical results show that the hybrid-shunting circuits can make the band-gaps wider by appropriately selecting the inductances, negative capacitances, and resistances.     

Singular variation property of elastic constants of piezoelectric ceramics shunted to negative capacitance

Piezoelectric shunt damping has been widely used in vibration suppression, sound absorption, noise elimination, etc.In such applications, the variant elastic constants of piezoelectric materials are the essential parameters that determine the performances of the systems, when piezoelectric materials are shunted to normal electrical elements, i.e., resistance,inductance and capacitance, as well as their combinations. In recent years, many researches have demonstrated that the wideband sound absorption or vibration suppression can be realized with piezoelectric materials shunted to negative capacitance. However, most systems using the negative-capacitance shunt circuits show their instabilities in the optimal condition, which are essentially caused by the singular variation properties of elastic constants of piezoelectric materials when shunted to negative capacitance. This paper aims at investigating the effects of negative-capacitance shunt circuits on elastic constants of a piezoelectric ceramic plate through theoretical analyses and experiments, which gives an rational explanation for why negative capacitance shunt circuit is prone to make structure instable. First, the relationships between the elastic constants c_(11), c_(33), c_(55) of the piezoelectric ceramic and the shunt negative capacitance are derived with the piezoelectric constitutive law theoretically. Then, an experimental setup is established to verify the theoretical results through observing the change of elastic constant c_(55) of the shunted piezoelectric plate with the variation of negative capacitance.The experimental results are in good agreement with the theoretical analyses, which reveals that the instability of the shunt damping system is essentially caused by the singular variation property of the elastic constants of piezoelectric material shunted to negative capacitance.     

Free vibration analysis of piezoelectric coupled circular plate with open circuit

A vibration analysis of a circular steel substrate surface bonded by a piezoelectric layer with open circuit is presented. A solution for the electrical potential along the thickness direction of the piezoelectric layer satisfying the open circuit electric boundary condition is developed for the first time. The mechanical model and solutions for the vibration analysis of the piezoelectric coupled circular plate are then established based on the developed electrical potential, the Kirchhoff plate model, and the Maxwell equation. The first four mode shapes and the corresponding resonant frequencies of the plate with two standard boundary conditions are presented in numerical simulations and compared with those of a piezoelectric coupled plate with the closed circuit condition. The simulations show that the resonant frequencies of the open circuit piezoelectric coupled plate are higher than those of the closed circuit piezoelectric coupled plate. Corresponding discussions are thus provided for the higher piezoelectric effect from the open circuit piezoelectric layer.     

混合压电分流电路作用下声子晶体杆振动带隙结构分析

对于电阻电感(RL)及负阻抗变换器(NIC)混合压电分流电路分别采用紧密及间隔排列方式进行带隙结构计算,并且针对分流电路中电阻、电感及电容对于局域共振带隙的影响进行研究。采用传递矩阵法建立了压电分流电路作用下声子晶体杆带隙分析的理论模型,并运用MATLAB语言对带隙结构进行编程仿真计算。通过电阻、电感、电容参数的匹配及电路不同排列方式的对比,最终得到了在混合间隔压电分流电路作用下宽度为13 kHz的带隙,并对振动控制系统稳定性进行了分析。研究结果表明:采用混合压电分流电路会对杆件带隙结果产生影响,且采用压电片间隔排列的方式会使带隙宽度明显扩大。      

Sound absorption characteristics of a thin plate with PZT and shunt circuitⅠ.Theoretical analysis

The feasibility of sound absorbing by a vibrating plate with piezoelectric material and shunt circuits is theoretically investigated.Based on an equivalent compliance of a piezoelectric wafer shunted with RL circuits,the governing equations for the flexural vibration of the plate with the piezoelectric wafer are derived using Lagrange's approach.The equations take into account not only the mass,stiffness and structural damping of the plate and the wafer,but also the electrical resistance and electrical i...     

A novel multimode negative inductance negative resistance shunted electromagnetic damping and its application on a cantilever plate

Based on the characteristic of the electromagnetic damping, a novel multimode vibration control treatment, negative inductance negative resistance electromagnetic shunt damping (NINR-EMSD), is proposed and employed to control multimode vibration of a cantilever plate. The negative inductance of the shunt impedance can cancel the inherent inductance of the electromagnet, and the impedance of circuit consisted of the coils and shunt will be a pure resistance and the shunt current will be frequency independent when the inductance of the shunt and the electromagnet are equal with each other. The negative resistance cancels the resistance of electromagnet, and as a result the resistance and the current of the closed circuit will change, which make it feasible to control the multimode vibration of the system. Electromechanical coupling coefficient is obtained based on the equivalent current method. The governing equation of the plate with the electromagnetic shunt damping (EMSD) is established according to Hamilton's principle. Multimode vibration control of the system is simulated and experiments are carried out to verify the performance of the NINR-EMSD. The numerical predictions and experimental results agree well with each other and show that: the negative inductance negative resistance (NINR) of the shunt impedance can increase the damping of the structure notably; the decrease of the resistance of shunt impedance have a significant contribution to the improvement of vibration control performance; the first four modes vibration of the plate can be suppressed simultaneously with the NINR-EMSD.     

Finite element modelling of piezolaminated smart structures for active vibration control with distributed sensors and actuators

Finite element modelling of laminated structures with distributed piezoelectric sensor and actuator layers and control electronics is considered in this paper. Beam, plate and shell type elements have been developed incorporating the stiffness, mass and electromechanical coupling effects of the piezoelectric laminates. The effects of temperature on the electrical and mechanical properties and the coupling between them are also taken into consideration in the finite element formulation. The piezoelectric beam element is based on Timoshenko beam theory. The plate/shell element is a nine-noded field-consistent element based on first order shear deformation theory. Constant-gain negative velocity feedback, Lyapunov feedback as well as a linear quadratic regulator (LQR) approach have been used for active vibration control with the structures subjected to impact, harmonic and random excitations. The influence of the pyroelectric effects on the vibration control performance is also investigated. The LQR approach is found to be more effective in vibration control with lesser peak voltages applied in the piezo actuator layers as in this case the control gains are obtained by minimizing a performance index. The application of these elements in high-performance, light-weight structural systems is highlighted.     

Band gap structure analysis of phononic crystal rods with hybrid shunted piezoelectric patches

The band gap structures by arranging hybrid shunted piezoelectric materialswith resistance inductive(RL) circuit and negative impedance converter(NIC) closely and at intervals are presented.The theoretical model is built using transfer matrix method.Then the MATLAB computing language is utilized to simulate the band gap structures.Meanwhile,the effects of the resistance,inductance and capacitance on the local resonant gap are studied.By comparing different combinations of resistance,inductance and capacitance as well as different arrangement of circuits,a 13 kHz band gap is reached under the effect of arranging hybrid periodic shunted piezoelectric patches at intervals and the stability of the system is also analyzed.It is proved that utilizing hybrid shunted piezoelectric patches would have a clear impact on the band gap structure of phononic crystal rods.Moreover,the band gap would be clearly enlarged by arranging hybrid piezoelectric patches at intervals.     

Active vibration suppression of multilayered plates integrated with piezoelectric fiber reinforced composites using an efficient finite element model

The active vibration suppression of hybrid composite and fiber metal laminate (FML) plates integrated with piezoelectric fiber reinforced composite (PFRC) sensors and actuators is studied for the first time, using an efficient and advanced layerwise plate theory. Unlike the conventional finite elements, the equipotential condition of electroded surfaces of sensors is satisfied exactly and conveniently using a novel concept of electric node. The effective electromechanical properties of the PFRC laminas are computed using a coupled three-dimensional iso-field micromechanical model. Numerical results are presented for both classical constant gain velocity feedback (CGVF) and optimal control strategies. The instability phenomena in CGVF control with conventionally collocated actuator-sensor pairs, and its remedy with a truly collocated arrangement are illustrated. The effect of segmentation of electrodes on the control response is studied. The segmentation of electrodes leads to a multi-input-multi-output (MIMO) configuration. The effects of piezoelectric fiber orientation, volume fraction and dielectric ratio of PFRC on the control response and the actuation/sensing authority are investigated for cantilever and simply supported plates.     

ACTIVE-PASSIVE PIEZOELECTRIC ABSORBERS FOR SYSTEMS UNDER MULTIPLE NON-STATIONARY HARMONIC EXCITATIONS

Previous research has shown that piezoelectric materials can be shunted with electrical networks to form devices that operate similarly to a mechanical vibration absorber. These systems can be tuned to provide modal damping (modal tuning) or to attenuate a harmonic disturbance (tonal tuning). Semi-active piezoelectric absorbers have also been proposed for suppressing harmonic excitations with varying frequency, a scenario that cannot be easily controlled using passive devices. However, these semi-active systems have limitations that restrict their applications. In a previous study, the authors have developed a high performance active-passive alternative to the semi-active absorber that uses a combination of a passive electrical circuit and active control actions. The active control consists of three parts: an adaptive inductor tuning action, a negative resistance action, and a coupling enhancement action. This new device has been shown, both analytically and experimentally, to be very effective for the suppression of harmonic disturbances with time-varying frequency. In the present paper, the adaptive active-passive piezoelectric absorber configuration is extended so that it can track and suppress multiple harmonic excitations. A new optimal tuning law is derived, and the stability conditions of the system are investigated. The effectiveness of this new multi-frequency absorber design is demonstrated by comparing its performance and control power requirement to the popular Filtered-x adaptive feedforward control algorithm.     

Dynamics modelling of beams with shunted piezoelectric elements

General modelling of a resonant shunting damper has been made from piezoelectric sensor/actuator equations. It is found that an additional damping, which is augmented to a system, is generated by the shunt damping effect. The transfer function of the tuned electrical absorber is derived for both series and parallel shunt circuit. The governing equations and associated boundary conditions are derived using Hamilton's principle. The shunt voltage equation is also derived from the charge generated in PZT due to beam vibration. The frequency response function of the obtained mathematical model is compared with that of the tuned electrical absorber and experimental work. The vibration amplitude is reduced about 15 dB at targeted second mode frequency.     

Active control of geometrically nonlinear transient vibration of composite plates with piezoelectric actuators

In this paper, the incremental finite element equations for geometric non-linear analysis of piezoelectric smart structures are developed using a total Lagrange approach by using virtual velocity incremental variational principles. A four-node first order shear plate element model with reduced and selective integration is also developed. Geometrically non-linear transient vibration response and control of plates with piezoelectric patches subjected to pulse loads are investigated. Active damping is introduced on the plates by coupling a self-sensing and negative velocity feedback algorithm in a closed control loop. The numerical results show that piezoelectric actuators can introduce significant damping and suppress transient vibration effectively. The effects of the number and locations of the piezoelectric actuators on the control system are also discussed.     

Optimum tuning of series and parallel LR circuits for passive vibration suppression using piezoelectric elements

Bending vibration of flexible structures can be suppressed passively using piezoelectric electromechanical transducers and optimally tuned LR circuits. Since these systems include both mechanical and electrical elements, the governing equations consist of electrically coupled equations of motion. This paper describes a new method for deriving the governing equations that describe a system’s vibration suppression based on the equilibrium of force principle and using an equivalent mechanical model of a piezoelectric element. Both series and parallel LR circuits are considered in the modeling approach. The optimum values for a mechanical vibration absorber can be formulated by using the two fixed points method. However, exact optimal values for the resistances of the LR circuits have not been formulated in the research literature thus far, and approximate values have been used. Analytical formulations are derived in this paper, and optimum values of the LR circuits are presented, not only in displacement, but also in terms of velocity and acceleration. The effects of the stiffness of the adhesive bond between the host structure and piezoelectric element, the dielectric loss in a piezoelectric element, and the internal resistance of an inductor are considered in the theoretical analysis. The effectiveness of the described analytical method is validated through simulations and experiments.     

Coupled FEM/BEM for control of noise radiation and sound transmission using piezoelectric shunt damping

In this paper, we present a coupled finite element/boundary element method (FEM/BEM) for control of noise radiation and sound transmission of vibrating structure by passive piezoelectric techniques. The system consists of an elastic structure (with surface mounted piezoelectric patches) coupled to external/internal acoustic domains. The passive shunt damping strategy is employed for vibration attenuation in the low frequency range. The originality of the present paper lies in evaluating the classically used FEM/BEM methods for structural–acoustics problems when taking account smart systems at the fluid–structure interfaces.