锂离子电池SnSb/MCMB核壳结构负极材料嵌锂性能研究

以酸处理的中间相碳微球(MCMB)为载体, 用化学还原法在碳球表面沉积SnSb合金, 合成SnSb 包覆碳球的核壳结构负极材料. 采用XRD, SEM技术对材料的结构和形貌进行了表征, 用恒电流充放电(CC)、循环伏安(CV)和交流阻抗(EIS)测试了材料的电化学性能. 实验结果表明: SnSb/MCMB样品呈现纳米晶与非晶态的混合组织; 单一SnSb合金的容量衰减较快, 而对于SnSb/MCMB复合材料, 细小的合金颗粒均匀钉扎在MCMB表面, 不仅改善了颗粒的团聚现象, 而且增强了材料的导电能力, 使材料的循环稳定性得到改善, 复合材料具有936.161 mAh/g的首次放电比容量, 首次库仑效率80.3%, 50次循环后容量维持在498.221 mAh/g. 关键词： SnSb合金 锂离子电池 中间相碳微球(MCMB) 电化学性能     

Co_2SnO_4/Graphene复合材料的制备与电化学性能研究

实验首先采用改进的Hummers法制备氧化石墨,然后以氧化石墨烯为前驱体,通过水热法将锡酸钴纳米颗粒均匀镶嵌在石墨烯薄膜基片上,最终获得Co2SnO4/Graphene镶嵌复合材料.采用X射线衍射(XRD)、扫描电子显微镜(SEM)对材料的结构和形貌进行表征,通过恒电流充放电(CC)、循环伏安法(CV)与交流阻抗法(EIS)测试了材料的电化学性能.实验结果表明,石墨烯良好的分散性及较高的电子导电率,可以提高锡酸钴材料的电化学性能,材料首次可逆容量达到1415.2 mA·h/g,50次循环后仍能保持469.7 mA·h/g的放电比容量.     

石墨烯包裹的爆米花中空结构的FeS纳米颗粒作为钠离子电池阳极的性能研究

用一步水热法合成多孔的爆米花形状的由还原石墨烯包裹的FeS纳米颗粒,该复合颗粒作为钠离子电池阳极使用。多孔结构有助于该复合物展现出优越的循环稳定性和速率性能。在电流密度为100 mA g-1时,100次循环之后该复合物依然保持可逆比容量552 mA h g-1;在电流密度为5000 mA g-1时,表现出比容量为307 mA h g-1。此外,Na, S 和 Fe的相图分析揭露了Na 和 FeS 在充放电过程中的氧化还原机制。     

锂离子电池Sn-Al薄膜电极的制备及电化学性能研究

采用磁控溅射沉积技术制备了纳米级Sn-Al合金薄膜电极材料,并用X射线衍射和扫描电子显微镜进行表征,用高精度电池测试系统进行充放电和循环伏安测试.结果表明直流DC与射频RF两种不同的溅射方法制备的Sn-Al薄膜电极具有很大的性能差异,前者DC法制备的材料颗粒细小,表现出稳定的循环性能,其首次放电容量为1060 mAh/g,首次效率为71.7％,电极经过50次循环后比容量保持在700 mAh/g以上.后者RF法制备的材料颗粒较大,放电比容量开始上升,第五次循环后接着逐渐衰减,表现出较差的循环性能. 关键词： 锂离子电池 磁控溅射 Sn-Al合金 电化学性能     

LiNi_(0.5)Mn_(0.5)O_2制备及表征

采用共沉淀法制备了LiNi0.5Mn0.5O2.XRD,Raman测试都表明材料是六方结构.XPS检测得出镍主要以正二价存在,锰元素主要以正四价存在.合成的LiNi0.5Mn0.5O2得到了50次的循环,但比容量较低.充放电循环性能比较研究表明,经过40次循环后,0.3,0.6,1.5 C的放电比容量分别是65.88,61.56,52.23 mA.h.g-1.     

CO_2活化温度对N-C复合碳气凝胶结构及电化学性能的影响

采用CO2活化工艺对氮掺杂碳气凝胶(N-CA)的结构进行重整,并系统研究了活化温度对活化氮掺杂碳气凝胶(N-ACA)孔结构及电化学性能的影响。利用N2吸附数据、X-光电子能谱(XPS)和元素分析对样品的结构及元素组成进行表征。结果表明,随活化温度的升高,N-ACA的比表面积逐渐增大,其含有的氮原子分数逐渐减少,吡咯氮含量明显增加。利用循环伏安(CV)、电化学阻抗谱(EIS)等测试技术评价了碳气凝胶样品在6mol·L-1 KOH电解液中的电化学性能,结果发现,合理的孔结构与较高的吡咯氮含量是影响电容器比容量的关键因素。在5mV·s-1扫描速率下测试950-N-ACA电极的比电容值高达267.4F·g-1,经1000次充放电后比电容损失值在1.5%以内。     

碳热还原法制备V2O3-C双层包覆磷酸铁锂及其电化学性能

通过V₂O₅的碳热还原反应制备了具有优异倍率性能和循环稳定性的V₂O₃-C双层包覆的磷酸铁锂正极材料. 粉末X射线衍射、元素分析、高分辨投射电镜和拉曼光谱研究表明V2O3相与碳层共包覆于磷酸铁锂颗粒表面. 在V₂O₅的碳热还原反应后,碳含量明显降低,但石墨化程度未发生明显改变. 电化学测试结果表明少量V₂O₃显著改善了磷酸铁锂正极材料的倍率性能和高温循环性能,包含1%氧化钒的复合正极材料在0.2 C放电容量为167 mAh/g,5 C时放电容量为129 mAh/g,并且循环稳定性优异;在55 oC和1 C时放电容量为151 mAh/g,循环100次后无明显容量衰减.     

Co$lt;sub$gt;2$lt;/sub$gt;SnO$lt;sub$gt;4$lt;/sub$gt;/Graphene复合材料的制备与电化学性能研究

实验首先采用改进的Hummers法制备氧化石墨,然后以氧化石墨烯为前驱体,通过水热法将锡酸钴纳米颗粒均匀镶嵌在石墨烯薄膜基片上,最终获得Co₂SnO₄/Graphene镶嵌复合材料. 采用X射线衍射（XRD）、扫描电子显微镜（SEM）对材料的结构和形貌进行表征,通过恒电流充放电（CC）、循环伏安法（CV）与交流阻抗法（EIS）测试了材料的电化学性能. 实验结果表明,石墨烯良好的分散性及较高的电子导电率,可以提高锡酸钴材料的电化学性能,材料首次可逆容量达到1415.2 mA·h/g,50次循环后仍能保持469.7 mA·h/g的放电比容量. 关键词： 2SnO₄')" href="#">Co₂SnO₄ 石墨烯 电化学性能 锂离子电池     

纳米铜掺杂Li(Ni_(0.6)Co_(0.2)Mn_(0.2))O_2正极材料的制备和性能研究

通过Cu纳米颗粒掺杂制备了Li[(Ni_(0.6)Co_(0.2)Mn_(0.2))_(1-x)Cu_x]O_2三元正极材料,并通过调节Cu的掺杂量,讨论了Cu的掺入对Li[(Ni_(0.6)Co_(0.2)Mn_(0.2))_(1-x)Cu_x]O_2三元正极材料晶体结构、表面形貌、电化学性能和循环性能等一系列性能的影响,铜掺杂量为x=0.01时,在0.2C倍率下的首次放电比容量达到了219.1 mAh/g,经过50次充放电循环之后,剩余比容量为115.4 mAh/g。最终结果为Li[(Ni_(0.6)Co_(0.2)Mn_(0.2))_(1-x)Cu_x]O_2中Cu的掺入量为x=0.01时,所得正极材料的电化学性能和循环性能最为优异。     

LiNi1-x-yCoxMnyO2正极材料的制备与电化学性能

LiNi_1-x-yCo_xMn_yO₂正极材料作为最有商业化前途的锂离子电池正极材料，近年来成为研究者关注的焦点。但目前针对该材料合成工艺的研究还较少。对LiNi_0.8Co_0.15Mn_0.05O₂开展了不同的烧结工艺研究，并对制备出的正极材料进行了表征和性能测试。研究发现在0.1C (电池容量额定值)倍率下充放电比容量为200 mA·h·g-1左右，在1C倍率循环100次下，480 ℃@3 h + 780 ℃@5 h和500 ℃@5 h + 780 ℃@10 h两种烧结工艺下容量保持率分别为94%和86%，说明用这两种工艺制备的正极材料的综合性能最优。     

Electrochemical hydrogen storage properties of melt-spun Ti0.9Zr0.1V0.2Ni1.5La0.5 alloy

The Ti_0.9Zr_0.1V_0.2Ni_1.5La_0.5 alloy samples were synthesized by melt-spinning technique at the different wheel velocity (cooling rate), and the structure and electrochemical hydrogen storage properties were investigated. The result indicated that the structure of the melt-spun ribbons mainly contains C14 Laves phase and V-based solid solution phase. The discharge capacity, cyclic stability, high-rate discharge ability and electrochemical kinetic of the alloy electrodes are correlated with the cooling rate (wheel velocity), and the maximum discharge capacity is over 200 mA·h/g at the wheel velocity of 20 m/s.     

In situ formed FeS2@CoS cathode for long cycling life lithium-ion battery

Pyrite FeS₂ exhibits an ultrahigh energy density (1671 W·h·kg^-1, for the reaction of FeS₂+4Li=Fe+2Li₂S) in secondary lithium-ion batteries, but its poor cycling stability, huge volume expansion, the shuttle effect of polysulfides, and slow kinetic properties limit its practical application. In this work, we synthesize a composite structure material CoS on FeS₂ surface (FeS_x@CoS, 1 < x ≤ 2) by using a cobalt-containing MOF to improve its cycle stability. It is found that CoS inhibits the side reactions and adsorbs polysulfides. As a result, the modified FeS₂ shows a higher discharge capacity of 577 mA·h·g^-1 (919 W·h·kg^-1) after 60 cycles than 484 mA·h·g^-1 (778 W·h·kg^-1) of bare pyrite FeS₂. This efficient strategy provides a valuable step toward the realization of high cycling stability FeS₂ cathode materials for secondary lithium-ion batteries and enriches the basic understanding of the influence of FeS₂ interfacial stability on its electrochemical performances.     

Design and synthesis of a novel 3D hierarchical mesocarbon microbead as anodes for lithium ion batteries and sodium ion batteries

This work presents a feasible route for the facile synthesis of three-dimensional (3D) hierarchical mesocarbon microbead (MCMB) as anodes for lithium ion batteries (LIBs) and sodium ion batteries (SIBs). The MCMB is oxidized by modified hummers method, and then the precursor is treated by hydrogen reduction to form the HMCMB. The HMCMB with graphene-like architecture has high specific surface, sufficient pore volume, and increased interlayer spacing, which can provide more active insertion/extraction sites and reduce the Li⁺/Na⁺ diffusion resistance. When employed as anode materials for LIBs and SIBs, HMCMB anodes exhibit improved lithium and sodium storage capability. The HMCMB delivers a higher reversible capacity (471.1 and 177.5 mAh g^?1 at 100 mA g^?1 after 100 cycles) and a good rate performance (250 and 121 mAh g^?1 even at 1000 mA g^?1) for LIBs and SIBs, respectively.     

A twins-structural Sn@C core–shell composite as anode materials for lithium-ion batteries

In this paper, we report a facile method to prepare a twins-structural Sn@C core–shell composite that is used as anode materials for lithium-ion batteries. Its surface morphology and microstructures were characterized by the scanning electron microscope, X-ray diffraction, and transmission electron microscope. The electrochemical performances of Sn@C were measured by charge–discharge tests, cyclic voltammogram, and electrochemical impedance spectra. It is shown that such a composite exhibits a high initial specific capacity of 970 mA h g^?1 and a capacity retention of 400 mA h g^?1 after 50 cycles at the current density of 100 mA g^?1.     

Facile synthesis of ultrafine SnO<Subscript>2</Subscript> nanoparticles on graphene nanosheets via thermal decomposition of tin-octoate as anode for lithium ion batteries

We demonstrate a facile synthesis of ultrafine SnO₂ nanoparticles within graphene nanosheets (GNSs) via thermal decomposition of tin-octoate, in which tin-octoate is firstly blended with GNSs followed by annealing in air at a low temperature (350 °C) and a short time (1 h). As anode for lithium ion batteries, the SnO₂/GNSs displays superior cycle and rate performance, delivering reversible capacities of 803 and 682 mA h/g at current densities of 200 and 500 mA/g after 120 cycles, respectively, much higher than that of pure SnO₂ and GNSs counterparts (143 and 310 mA h/g at 500 mA/g after 120 cycles, respectively). The enhanced electrochemical performance is attributed to the ultrafine SnO₂ nanoparticle size and introduction of GNSs. GNSs prevent the aggregation of the ultrafine SnO₂ nanoparticles, which alleviate the stress and also provide more electrochemically active sites for lithium insertion and extraction. Moreover, GNSs with large specific surface area (~363 m²/g) act as a good electrical conductor which greatly improves the electrode conductivity and also an excellent buffer matrix to tolerate the severe volume changes originated from the Li-Sn alloying-dealloying. This work provides a straight-forward synthetic approach for the design of novel composite anode materials with superior electrochemical performance.     

Three-dimensional nitrogen-doped graphene/sulfur composite for lithium-sulfur battery

A three-dimensional nitrogen-doped graphene/sulfur composite (NGS3) was synthesized by a simple hydrothermal method using urea as the nitrogen source and subsequent thermal treatment. The structure and electrochemical performance of the prepared nitrogen-doped graphene/sulfur composite (NGS3) were confirmed by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM), Energy dispersive spectroscopy mapping (EDS), and galvanostatic charge/discharge measurements. SEM and EDS mapping show that NGS3 exhibits a porous structure with uniform distribution of sulfur. Compared with the graphene/sulfur composite (NGS1), NGS3 delivers an outstanding rate capability with 1501, 1278, 1136, and 1024 mAh g^?1 at 200, 400, 800, and 1000 mA g^?1, respectively, and the cycle stability of NGS3 is also wonderful, a reversible discharge capacity of 1330 mAh g^?1 is obtained after 80 cycles under the current rate of 200 mA g^?1. The wonderful electrochemical performance could be attributed to the special three-dimensional conductive structure with the help of nitrogen atom.     

Preparation of Si-PPy-Ag composites and their electrochemical performance as anode for lithium-ion batteries

The nanosilicon connected by polypyrrole (PPy) and silver (Ag) particles was simply synthesized by a chemical polymerization process in order to prepare Si-based anodes for Li-ion batteries. The phase structure, surface morphology, and electrochemical properties of the as-synthesized powders were analyzed by X-ray diffraction, FT-IR, scanning electron microscopy, and galvanostatic charge/discharge measurements. The cycle stability of the Si-PPy-Ag composites was greatly enhanced compared with the pure nanosilicon. A high capacity of more than 823 mA h g^?1 was maintained after 100 cycles. The improved electrochemical characteristics are attributed to the volume buffering effect as well as effective electronic conductivity of the polypyrrole and silver in the composite electrode.     

Sulfur/microporous carbon composites for Li-S battery

A commercial carbon black with microporous framework is used as carbon matrix to prepare sulfur/microporous carbon (S/MC) composites for the cathode of lithium sulfur (Li-S) battery. The S/MC composites with 50, 60, and 72 wt.% sulfur loading are prepared by a facile heat treatment method. Electrochemical performance of the as-prepared S/MC composites are measured by galvanostatic charge/discharge tests, cyclic voltammetry (CV), and electrochemical impedance spectroscopy (EIS), with carbonate-based electrolyte of 1.0 M LiPF₆/(PC-EC-DEC). The composite with 50 wt.% sulfur presents the optimized electrochemical performance, including the utilization of active sulfur, discharge capacity, and cycling stability. At the current density of 50 mA g^?1, it can demonstrate a high initial discharge capacity of 1624.5 mAh g^?1. Even at the current density of 800 mA g^?1, the initial capacity of 1288.6 mAh g^?1 can be obtained, and the capacity can still maintain at 522.8 mAh g^?1 after 180 cycles. The remarkably improved electrochemical performance of the S/MC composite with 50 wt.% sulfur are attributed to the carbon matrix with microporous structure, which can effectively enhance the electrical conductivity of the sulfur cathode, suppress the loss of active material during charge/discharge processes, and restrain the migration of polysulfide ions to the lithium anode.