Dislocation dynamics in multiwalled carbon nanotubes at high temperatures

Dislocation dynamics dictate the mechanical behavior of materials. Dislocations in periodic crystalline materials have been well documented. On the contrary, dislocations in cylindrical carbon nanotubes, particularly in multiwalled carbon nanotubes (MWCNTs), remain almost unexplored. Here we report that a room temperature 1/2<0001> sessile dislocation in a MWCNT becomes highly mobile, as characterized by its glide, climb, and the glide-climb interactions, at temperatures of about 2000 degrees C. The dislocation glide leads to the cross-linking of different shells; dislocation climb creates nanocracks; and the interaction of two 1/2<0001> dislocations creates kinks. We found that dislocation loops act as channels for mass transport. These dislocation dynamics are drastically different from that in conventional periodic crystalline materials due to the cylindrical, highly anisotropic structures of MWCNTs.     

Climb via vacancy diffusion of edge dislocations in 2D dislocation microstructures

The prevention of strength degradation of components is one of the great challenges in solid mechanics. In particular, at high temperatures material may deform even at low stresses, a deformation mode known as deformation creep. One of the microstructural mechanisms that governs deformation creep is dislocation motion due to the absorption or emission of vacancies, which results in motion perpendicular to the glide plane, called dislocation climb. However, the importance of the dislocation network for the deformation creep remains far from being understood. In this study, a climb model that accounts for the dislocation network is developed, by solving the diffusion equation for vacancies in a region with a general dislocation distribution. The definition of the sink strength is extended, to account for the contributions of neighbouring dislocations to the climb rate. The model is then applied to dislocation dipoles and dislocation pile-ups, which are dense dislocation structures and it is found that the sink strength of dislocations in a pile-up is reduced since the vacancy field is distributed between the dislocations. Finally, the importance of the results for modelling deformation creep is discussed.     

The formation of dislocation networks

The formation of small angle boundaries consisting of dislocation networks is considered mainly on the basis of studies concerning the hot-deformation of Al-Mg alloys solidified with well developed sub-structures. It is shown that different kinds of network are built up on dislocation forests by dislocations which encounter the forest by glide and then change the mode of motion from glide to climb. Special attention is given to the mechanism of climb which enables the rapid knitting of networks during hot-deformation, and also to the annihilation of dislocations which prevents the increase in flow stress.     

Defect structure in EuS single crystals grown from the melt

The defect structure in EuS single crystals grown form the melt is studied by etch pitting, scanning and high-voltage electron microscopy. Circular and square etch pits and a second phase in the shape of thin hexagonal platelets are observed by etching. Microprobe analysis indicates the platelets to consist of Eu metal. In the transmission electron microscope, smoothly curved dislocations and helical dislocations, small dislocation loops and inclusions associated with dislocations are observed. The possible origin of the detected dislocation structure is considered with reference to climb and glide processes occurring during cooling down the grown crystals. The results corroborate the glide geometry of the NaCl lattice for EuS. On leave from Institute of Physics, Academic Sinica, Peking, VR China     

Dislocations and mechanical properties of icosahedral quasicrystals

In this article we interpret the mechanical properties of icosahedral quasicrystals with the dislocation theory. After having defined the concept of dislocation in a periodic crystal, we extend this notion to quasicrystals in the 6-dimensional space. We show that perfect dislocations and imperfect dislocations trailing a phason fault can be defined and observed in transmission electron microscopy (TEM). In-situ straining TEM experiments at high temperature show that dislocations move solely by climb, a non-conservative motion-requiring diffusion. This behavior at variance with that of crystals which deform mainly by glide is explained by the atypical nature of the atomic structure of icosahedral quasicrystals.     

Kink formation and motion in carbon nanotubes at high temperatures

We report that kink motion is a universal plastic deformation mode in all carbon nanotubes when being tensile loaded at high temperatures. The kink motion, observed inside a high-resolution transmission electron microscope, is reminiscent of dislocation motion in crystalline materials: namely, it dissociates and multiplies. The kinks are nucleated from vacancy creation and aggregation, and propagate in either a longitudinal or a spiral path along the nanotube walls. The kink motion is related to dislocation glide and climb influenced by external stress and high temperatures in carbon nanotubes.     

Positron annihilation in alpha- and beta-cyclodextrin

A new type of misfit dislocation multiplication is deduced from high-voltage electron micrographs of thin Ge layers on GaAs substrates. Two misfit dislocations with the same Burgers vectors on different glide planes cross and annihilate at the intersection point resulting in the formation of two angular dislocations. The tip of one of these dislocations may reach the growth surface by glide breaking into two separate dislocation segments. These segments may glide to form additional misfit dislocations, which may undergo the same multiplication process.     

Mechanisms of high-temperature creep of nickel-based superalloys under low applied stresses

[001] single-crystal specimens of the superalloys CMSX-4 and CMSX-10 were tested for creep at 1100°C under tensile stresses between 105 and 135?MPa, where they show pronounced steady creep. The deformed superalloys were analysed by density measurements, scanning electron microscopy and transmission electron microscopy which supplied information about porosity growth, evolution of the γ–γ′ microstructure, dislocation mobility and reactions during creep deformation. It is shown that, under the testing conditions used, steady creep strain mostly results from transverse glide–climb of (a/2) ?011? interfacial dislocations. A by-product of the interfacial glide–climb are vacancies which diffuse along the interfaces to growing pores or to a ?100? edge dislocations climbing in the γ′ phase. Climb of a ?100? dislocations in the γ′ phase is a recovery mechanism which reduces the constraining of the γ phase by the γ′ phase, thus enabling further glide of (a/2) ?011? dislocations in the matrix. Moreover the γ′ dislocations act as vacancy sinks facilitating interfacial glide–climb. The creep rate increases when the γ–γ′ microstructure becomes topologically inverted; connection of the γ′ rafts results in extensive transverse climb and an increase of the number of a?100? dislocation segments in the γ′ phase.     

Observations of glide and decomposition of a⟨101⟩ dislocations at high temperatures in Ni-Al single crystals deformed along the hard orientation

Ni-44 at.% Al and Ni-50 at.% Al single crystals were tested in compression in the hard d001 ¢orientation. The dislocation processes and deformation behaviour were studied as a function of temperature, strain and strain rate. A slip transition in NiAl occurs from a?111? slip to non-a?111? slip at intermediate temperatures. In Ni-50 at.% Al single crystals, only a?010? dislocations are observed above the slip transition temperature. In contrast, a a?101?{101} glide has been observed to control deformation beyond the slip transition temperature in Ni-44 at.% Al. a?101? dislocations are observed primarily along both ?111? directions in the glide plane. High-resolution transmission electron microscopy observations show that the core of the a?101? dislocations along these directions is decomposed into two a?010? dislocations, separated by a distance of approximately 2 nm. The temperature window of stability for these a?101? dislocations depends upon the strain rate. At a strain rate of 1.4 210^?4 s^?1, a?101? dislocations are observed between 800 and 1000 K. Complete decomposition of a?101? dislocations into a?010? dislocations occurs beyond 1000 K, leading to a?010? climb as the deformation mode at higher temperatures. At lower strain rates, decomposition of a?101? dislocations has been observed to occur along the edge orientation at temperatures below 1000 K. Embedded-atom method calculations and experimental results indicate that a?101? dislocations have a large Peierls stress at low temperatures. Based on the present microstructural observations and a survey of the literature with respect to vacancy content and diffusion in NiAl, a model is proposed for a?101?{101} glide in Ni-44 at.% Al, and for the observed yield strength versus temperature behaviour of Ni-Al alloys at intermediate and high temperatures.     

Asymptotic behaviors of the stress fields in the vicinity of dislocations and dislocation segments

We obtain the singular asymptotic behavior of the stress field in the vicinity of a non-planar dislocation in three dimensions and the nearly singular behavior of the full self-force of the dislocation including both glide and climb forces, using asymptotic analysis. We also derive asymptotic formulas for the stress field in the vicinity of a curved dislocation segment. Numerical examples are presented to examine the asymptotic formulas. The obtained formulas can be used for qualitative understanding of the stress tensor associated with dislocations and efficient and accurate calculation of the stress tensor in dislocation dynamics simulations.     

Structure, stability, and motion of dislocations in double-wall carbon nanotubes

In this paper,a novel double-wall carbon nanotube(DWCNT) with both edge and screw dislocations is studied by using the molecular dynamics(MD) method.The differences between two adjacent tubule indexes of armchair and zigzag nanotubes are determined to be 5 and 9,respectively,by taking into account the symmetry,integrality,and thermal stability of the composite structures.It is found that melting first occurs near the dislocations,and the melting temperatures of the dislocated armchair and zigzag DWCNTs are around 2600 K-2700 K.At the premelting temperatures,the shrink of the dislocation loop,which is comprised of edge and screw dislocations,implies that the composite dislocation in DWCNTs has self-healing ability.The dislocated DWCNTs first fracture at the edge dislocations,which induces the entire break in axial tensile test.The dislocated DWCNTs have a smaller fracture strength compared to the perfect DWCNTs.Our results not only match with the dislocation glide of carbon nanotubes(CNTs) in experiments,but also can free from the electron beam radiation under experimental conditions observed by the high resolution transmission electron microscope(HRTEM),which is deemed to cause the motion of dislocation loop.     

镍铬合金中的位错运动与位错反应

对镍铬合金中单一滑移面内和两个滑移面间的位错反应,特别是动态下的反应,进行了透射电子显微镜观察,并对其中的一些位错组态进行了衍衬分析。1.六角位错网络主要是单一滑移面内柏氏矢量相差120°的两组位错间反应的结果;2.与螺型位错一样,刃型或混合型位错也能在两个滑移面间交滑移;3.两个滑移面间的位错反应有时在其截线方向生成不滑动的位错(如L.C.位错锁)并不能完全阻挡住这两个滑移面上的位错运动;4.在含铝、钛的镍铬合金中,超点阵位错的反应与不含铝、钛的合金或无序固溶体中的位错反应相似。 关键词：     

Dislocation emission at the onset of plasticity during nanoindentation in gold

Nanoindentations and the subsequent plastic damage in the form of dislocation configurations have been both generated and imaged with scanning tunnelling microscopy on a reconstructed Au(001) surface, the resulting observations being interpreted in terms of the elastic theory of dislocations in a continuum. The rearranged pileup material around the nanoindentation is described in terms of dislocation emission and glide involving, in particular, multiple cross-slip. ‘Mesas’, shallow protusions stemming from a special dislocation configuration consisting of Schockley partial dislocations encompassing two stacking faults, are shown to glide parallel to the surface under the stress generated by further nanoindentations. The spatial distribution of ‘mesas’ around the nanoindentation traces is shown to be controlled by a balance between the interactions between the different ‘mesas’ and the stresses arising from the nanoindentation itself.     

Interaction of Lomer–Cottrell locks with screw dislocations

In fcc crystals, dislocations are dissociated into partial dislocations and, therefore, restricted to move on {111} glide planes. By junction reactions with dislocations on two intersecting {111} planes, Lomer–Cottrell dislocations along ?110? directions can be formed which are barriers for approaching screw dislocations. Treating the interaction between a dissociated screw dislocation and a LC lock conventionally, using classical continuum theory and assuming the partials to be Volterra dislocations, leads to erroneous conclusions. A realistic result can only be obtained in the framework of the Peierls model, treating the partials as Peierls dislocations and explicitly taking account of the change in atomic misfit energy in the glide plane. At even moderate stresses (at less than 3 × 10^?3 µ in Cu), the screw will combine with the LC lock to form a Hirth lock. As a result, the nature of the repulsive force will change drastically.     

Diffusive fluxes associated with interfacial defeet motion and interaction

The diffusional flux associated with the motion of interfacial defects is described by an equation expressed in terms of the topological parameters which characterise defects, namely their Burgers vectors and step heights, the defect velocity and the concentration of each atomic species in the two adjacent crystals. This expression demonstrates that glide/climb behaviour of grain boundary defects is analogous to motion of dislocations in single crystals; climb motion results if a component of b is perpendicular to the interface plane. However, the situation is more complex in the case of interphase interface defects, but the present approach, which considers the step and dislocation portions of defects separately, enables a straightforward analysis. Several examples are illustrated to show the various possibilities, such as climb motion even when b is parallel to the interface, and glide motion when b is not. The latter case arises in martensitic transformation where the existence of an invariant-plane-strain relation at the interface leads to equal and opposite fluxes to the step and dislocation portions of transformation defects so that overall the motion is diffusionless.Interfacial processes involve the motion and interaction of defects. The present analysis facilitates the consideration of diffusive fluxes associated with defect interaction since the step and dislocation portions can be treated independently. A general expression is derived for the total flux arising, and a particular case, the interaction of transformation dislocations with crystal dislocations which have reached the interface during lattice-invariant deformation in martensite formation, is considered.     

Topological kinematic constraints: dislocations and the glide principle

Topological defects play an important role in the physics of elastic media and liquid crystals. Defect kinematics in elastic media is restrained by rigid constraints of purely topological origin. An example is the glide motion of dislocations, a topic which has been extensively studied through the years by metallurgists. To date, most theoretical investigations of this phenomenon were heuristic or numerical. Here, we outline a mathematical derivation of this universal effect and report on new generalizations. Our formalism makes it possible to address the full non-linear theory of relevance at short distance where violations of the standard glide constraint become possible. Our new derivation enables us to systematically predict and estimate corrections to the standard, linear order, glide motion. Our analysis is very broad and pertains to both classical and quantum media. To fully capture the generality of this effect, we arrive at a mathematical definition of the glide constraint which has a universal status. When fused with the mass continuity equations, this then dictates glide motion within linear elasticity and leads to new non-linear corrections in a general elastic medium. It further enables us to study the kinematics of dislocations in arbitrary spatial dimensions (or space-time dimensions in the quantum arena). As an example, we analyze the restricted climb associated with edge dislocations in 3±1D. Quite generally, the climb constraint is equivalent to the condition that dislocations do not communicate with compressional stresses at long distances.     

Surface stress mediated image force and torque on an edge dislocation

The proximity of interfaces gives prominence to image forces experienced by dislocations. The presence of surface stress alters the traction-free boundary conditions existing on free-surfaces and hence is expected to alter the magnitude of the image force. In the current work, using a combined simulation of surface stress and an edge dislocation in a semi-infinite body, we evaluate the configurational effects on the system. We demonstrate that if the extra half-plane of the edge dislocation is parallel to the surface, the image force (glide) is not altered due to surface stress; however, the dislocation experiences a torque. The surface stress breaks the ‘climb image force’ symmetry, thus leading to non-equivalence between positive and negative climb. We discover an equilibrium position for the edge dislocation in the positive ‘climb geometry’, arising due to a competition between the interaction of the dislocation stress fields with the surface stress and the image dislocation. Torque in the climb configuration is not affected by surface stress (remains zero). Surface stress is computed using a recently developed two-scale model based on Shuttleworth’s idea and image forces using a finite element model developed earlier. The effect of surface stress on the image force and torque experienced by the dislocation monopole is analysed using illustrative 3D models.     

Dislocation-density-based constitutive modelling of tensile flow and work-hardening behaviour of P92 steel

The flow and work-hardening behaviour of tempered martensitic P92 steel have been investigated using phenomenological constitutive model in the temperature range 300–873 K for the strain rates ranging from 3.16 × 10^?5 to 1.26 × 10^?3 s^?1. The analysis indicated that the hybrid model reduced to Estrin–Mecking (E–M) one-internal-variable model at intermediate and high temperatures. Further, the analysis also indicated that dislocation dense martensite lath/cell boundaries and precipitates together act as effective barriers to dislocation glide in P92 steel. The flow behaviour of the steel was adequately described by the E–M approach for the range of temperatures and strain rates examined. Three distinct temperature regimes have been obtained for the variations in work-hardening parameters with respect to temperature and strain rate. Signatures of dynamic strain ageing in terms of the anomalous variations in work-hardening parameters at intermediate temperatures and the dominance of dynamic recovery at high temperatures have been observed. The evaluation of activation energy suggested that deformation is controlled by the dominance of cross-slip of dislocations at room and intermediate temperatures, and climb of dislocations at high temperatures.     

A parametric simulation method for discrete dislocation dynamics

A new computer simulation method employed in discrete dislocation dynamics is presented. The article summarizes results of an application of the method to elementary interactions among glide dislocations and dipolar dislocation loops. The glide dislocations are represented by parametrically described curves moving in glide planes whereas the dipolar loops are treated as rigid objects. All mutual force interactions are considered in the models. As a consequence, the computational complexity rapidly increases with the number of objects considered. This difficulty is treated by advanced computational techniques such as suitable accurate numerical methods and parallel implementation of the algorithms. Therefore the method is able to simulate particular phenomena of dislocation dynamics which occur in crystalline solids deformed by single slip: generation of glide dislocations from the Frank-Read source, interaction of glide dislocations with obstacles, their encounters in channels of the bands, sweeping of dipolar loops by glide dislocations and a loop clustering.     

A computational approach towards modelling dislocation transmission across phase boundaries

To study the nanoscopic interaction between edge dislocations and a phase boundary within a two-phase microstructure the effect of the phase contrast on the internal stress field due to the dislocations needs to be taken into account. For this purpose a 2D semi-discrete model is proposed in this paper. It consists of two distinct phases, each with its specific material properties, separated by a fully coherent and non-damaging phase boundary. Each phase is modelled as a continuum enriched with a Peierls–Nabarro (PN) dislocation region, confining dislocation motion to a discrete plane, the glide plane. In this paper, a single glide plane perpendicular to and continuous across the phase boundary is considered. Along the glide plane bulk induced shear tractions are balanced by glide plane shear tractions based on the classical PN model. The model's ability to capture dislocation obstruction at phase boundaries, dislocation pile-ups and dislocation transmission is studied. Results show that the phase contrast in material properties (e.g. elastic stiffness, glide plane properties) alone creates a barrier to the motion of dislocations from a soft to a hard phase. The proposed model accounts for the interplay between dislocations, external boundaries and phase boundary and thus represents a suitable tool for studying edge dislocation–phase boundary interaction in two-phase microstructures.