An evaluation of a combined isotropic-kinematic hardening model for representation of complex strain-path changes in dual-phase steel

This paper aims at evaluating an elastoplastic constitutive model which accounts for combined isotropic-kinematic hardening for complex strain-path changes in a dual-phase steel, DP800. The capability of the model to reproduce the transient hardening phenomena under two-stage non-proportional loading has been assessed through numerical simulations of sequential uniaxial tension and notched tension/shear tests. Finite element simulations with shell elements were performed using the explicit non-linear FE code LS-DYNA. Numerical predictions of the stress–strain response were compared to the corresponding experimental data. The results from the experiments demonstrated that prior plastic deformation has certainly influenced the subsequent work-hardening behaviour of the material under biaxial or shear deformation modes. Furthermore, the numerical simulations from the two-stage uniaxial tension–notched tension and uniaxial tension–shear tests predicted the general trends of the experimental results such as transitory hardening and overall work hardening. However, some discrepancies were found in accurately describing the transient hardening behaviour subsequent to strain path changes between the experiments and numerical simulations.     

Modelling of the plastic flow of trip-aided multiphase steel based on an incremental mean-field approach

An incremental mean-field model is developed for the prediction of transformation induced plasticity (TRIP) in multiphase steel. The partitioning of strain between softer and harder constituents is computed based on an elastic-plastic Mori–Tanaka approach that accounts for the progressive transformation of austenite into martensite. The latter transformation is predicted using an energy-balance criterion that is formulated at the level of individual austenite grains. The model has been tested against experimental data. Macroscopic stress-strain curves and rate of martensite formation have been measured on sheet samples subjected to various loading modes: uniaxial tension, simple shear, and (in-plane) uniaxial compression. These experiments were performed at 20 °C and the uniaxial tensile test was repeated at ?30 °C. The mean-field model produces fair predictions of the macroscopic hardening resulting from TRIP on the condition that a sufficient proportion of the load is carried by the very hard martensite inclusions. Such prediction implies that one accounts for the stress heterogeneity across the ferrite-based matrix. At the same time, the model reproduces the elastic lattice strains and the plastic elongation which are measured within the phases by neutron diffraction and by image correlation in a scanning electron microscope, respectively. The model can be used in finite element simulations of forming processes which is illustrated in a study of necking of a cylindrical bar under uniaxial tension.     

Anisotropic strain hardening behavior in simple shear for cube textured aluminum alloy sheets

Finite element (FE) simulations of the simple shear test were conducted for 1050-O and 6022-T4 aluminum alloy sheet samples. Simulations were conducted with two different constitutive equations to account for plastic anisotropy: Either a recently proposed anisotropic yield function combined with an isotropic strain hardening law or a crystal plasticity model. The FE computed shear stress–shear strain curves were compared to the experimental curves measured for the two materials in previous works. Both phenomenological and polycrystal approaches led to results consistent with the experiments. These comparisons lead to a discussion concerning the assessment of anisotropic hardening in the simple shear test.     

A constitutive model of cyclic plasticity

This paper addresses a constitutive model of cyclic plasticity with special emphasis on the yield-point phenomena. In order to point out the deformation characteristics of a mild steel, four types of experiments were conducted, i.e. uniaxial tension at several crosshead speeds, cyclic straining, and stress- and strain-controlled ratchetting. A viscoplastic constitutive model of cyclic plasticity is proposed on the premise that the phenomena of sharp yield point and the subsequent abrupt yield drop result from rapid dislocation multiplication and the stress-dependence of dislocation velocity. Besides, cyclic plasticity behavior, such as the Bauschinger effect, cyclic hardening/softening characteristics and ratchet-strain accumulation, is described by some kinematic and isotropic hardening rules. The cyclic stress–strain responses predicted by this model agree well with the corresponding experimental results.     

A plane stress anisotropic plastic flow theory for orthotropic sheet metals

A phenomenological theory is presented for describing the anisotropic plastic flow of orthotropic polycrystalline aluminum sheet metals under plane stress. The theory uses a stress exponent, a rate-dependent effective flow strength function, and five anisotropic material functions to specify a flow potential, an associated flow rule of plastic strain rates, a flow rule of plastic spin, and an evolution law of isotropic hardening of a sheet metal. Each of the five anisotropic material functions may be represented by a truncated Fourier series based on the orthotropic symmetry of the sheet metal and their Fourier coefficients can be determined using experimental data obtained from uniaxial tension and equal biaxial tension tests. Depending on the number of uniaxial tension tests conducted, three models with various degrees of planar anisotropy are constructed based on the proposed plasticity theory for power-law strain hardening sheet metals. These models are applied successfully to describe the anisotropic plastic flow behavior of 10 commercial aluminum alloy sheet metals reported in the literature.     

Craft––a plastic-damage-contact model for concrete. I. Model theory and thermodynamic considerations

A framework is described for the development of a thermodynamically consistent plastic directional-damage-contact model for concrete. This framework is used as a basis for a new model, named Craft, which uses planes of degradation that can undergo damage and separation but which can regain contact according to a contact state function. The thermodynamic validity of the resulting model is considered in detail, and is proved for certain cases and demonstrated numerically for others. The model has a fully integrated plasticity component that uses a smooth triaxial yield surface and frictional hardening–softening functions. A new type of consistency condition is introduced for simultaneously maintaining both local and global constitutive relationships as well as stress transformation relationships. The introduction of contact theory provides the model with the ability to simulate the type of delayed aggregate interlock behavior exhibited by fully open crack surfaces that subsequently undergo significant shear movement. The model has been implemented in a constitutive driver program as well as a finite element program. The model is assessed against a range of experimental data, which includes data from uniaxial tension tests with and without unloading–reloading cycles, tests in which cracks are formed and then loaded in shear, and uniaxial, biaxial and triaxial compression tests.     

Micromechanical modeling of the elasto-viscoplastic behavior of semi-crystalline polymers

A micromechanically based constitutive model for the elasto-viscoplastic deformation and texture evolution of semi-crystalline polymers is developed. The model idealizes the microstructure to consist of an aggregate of two-phase layered composite inclusions. A new framework for the composite inclusion model is formulated to facilitate the use of finite deformation elasto-viscoplastic constitutive models for each constituent phase. The crystalline lamellae are modeled as anisotropic elastic with plastic flow occurring via crystallographic slip. The amorphous phase is modeled as isotropic elastic with plastic flow being a rate-dependent process with strain hardening resulting from molecular orientation. The volume-averaged deformation and stress within the inclusions are related to the macroscopic fields by a hybrid interaction model. The uniaxial compression of initially isotropic high density polyethylene (HDPE) is taken as a case study. The ability of the model to capture the elasto-plastic stress-strain behavior of HDPE during monotonic and cyclic loading, the evolution of anisotropy, and the effect of crystallinity on initial modulus, yield stress, post-yield behavior and unloading-reloading cycles are presented.     

Constitutive model for uniaxial transformation ratchetting of super-elastic NiTi shape memory alloy at room temperature

The transformation ratchetting of super-elastic NiTi shape memory alloy was observed by the uniaxial stress-controlled cyclic tests [Kang, G.Z., Kan, Q.H., Qian, L.M., Liu, Y.J, 2009a. Ratchetting deformation of super-elastic and shape memory NiTi Alloys. Mech. Mater. 41, 139–153]. It is concluded that the NiTi alloy presents apparent ratchetting behaviour, and the ratchetting is collectively caused by the cyclic accumulation of residual induced-martensite and the transformation-induced plastic deformation (i.e., namely transformation ratchetting). Based on the experimental results, a cyclic constitutive model was constructed in the framework of generalized plasticity [Lubliner, J., Auricchio, F., 1996. Generalized plasticity and shape memory alloys. Int. J. Solids Struct. 33, 991–1003] to describe the transformation ratchetting of super-elastic NiTi alloy. The proposed model simultaneously accounts for the evolutions of residual induced-martensite and transformation-induced plastic strain during the stress-controlled cyclic loading by introducing an internal variable z_c, i.e., cumulated induced-martensite volume fraction. The dependence of transformation ratchetting on the applied stress levels and the phase transformation hardening behaviour of the NiTi alloy are also considered in the developed model. The anisotropic phase transformation behaviours of the alloy presented in the tension and compression cases are described by employing a Drucker–Prager-typed transformation surface. It is shown that the simulated results of transformation ratchetting obtained by the proposed model are in good agreement with the corresponding experiments, since the typical features of transformation ratchetting are reasonably captured by the proposed model.     

Anisotropic plasticity for sheet metals using the concept of combined isotropic-kinematic hardening

Hill's 1948 anisotropic theory of plasticity (Hill, R., 1948. A theory of yielding and plastic flow of anisotropic metals. Proc. Roy. Soc. London A193, 281–297) is extended to include the concept of combined isotropic-kinematic hardening, and the objective of this paper is to validate the model so that it may be useful for analyses of sheet metal forming. Isotropic hardening and kinematic hardening may be experimentally observed in sheet metals, if yielding is defined by the proportional limit or by a small proof strain. In this paper, a single exponential term is used to describe isotropic hardening and Prager's linear kinematic hardening rule is applied for simplicity. It is shown that this model can satisfactorily describe both the yield stress and the plastic strain ratio, the R-ratio, observed in tension test of specimens cut at various angles measured from the rolling direction of the sheet. Kinematic hardening leads to a gradual change in the direction of the plastic strain increment, as the axial strain increases in the tension test; while in the traditional approach for sheet metal, this direction does not change due to the use of isotropic hardening.     

Nonproportional loading effects on elastic-plastic behavior based on stress resultants for thin plates of strain hardening materials

A stress resultant constitutive law in rate form is constructed for power-law hardening materials. The change of plate thickness is considered in the constitutive law. The elastic-plastic behavior of a plate element based on the stress resultant constitutive law under uniaxial combined tension and bending is determined under a limited number of nonproportional and unloading paths. The results based on the stress resultant constitutive law and the through-the-thickness integration method are compared within the context of both the small-strain and finite deformation approaches. The results indicate that the selection of the normalized equivalent stress resultant and the corresponding work-conjugate normalized equivalent generalized strain is appropriate for describing the hardening behavior in the stress resultant space. However, the hardening rule in a power law form must be modified for low hardening materials at large plastic deformation when finite deformation effects are considered.     

准脆性材料的弹塑性各向异性损伤耦合本构模型研究

针对准脆性材料的非线性特征：强度软化和刚度退化、单边效应、侧限强化和拉压软化、不可恢复变形、剪胀及非弹性体胀,在热动力学框架内,建立了准脆性材料的弹塑性与各向异性损伤耦合的本构关系。对准脆性材料的变形机理和损伤诱发的各向异性进行了诠释,并给出了损伤构形和有效构形中各物理量之间的关系。在有效应力空间内,建立了塑性屈服准则、拉压不同的塑性随动强化法则和各向同性强化法则。在损伤构形中,采用应变能释放率,建立了拉压损伤准则、拉压不同的损伤随动强化法则和各向同性强化法则。基于塑性屈服准则和损伤准则,构建了塑性势泛函和损伤势泛函,并由正交性法则,给出了塑性和损伤强化效应内变量的演化规律,同时,联立塑性屈服面和损伤加载面,给出了塑性流动和损伤演化内变量的演化法则。将损伤力学和塑性力学结合起来,建立了应变驱动的应力-应变增量本构关系,给出了本构数值积分的要点。以单轴加载-卸载往复试验识别和校准了本构材料常数,并对单轴单调试验、单轴加载-卸载往复试验、二轴受压、二轴拉压试验和三轴受压试验进行了预测,并与试验结果作了比较,结果表明,所建本构模型对准脆性材料的非线性材料性能有良好的预测能力。     

形状记忆合金相变塑性的统一本构理论

本文根据单品相变时其宏观(长程)切应变(等效应变)与外加切应力(等效应力)问的幂函数关系假定,建立了形状记忆合金多晶体相变塑性的统一细观本构理论,它推广了现有细观本构理论的结果,消除了现有理论中存在的当外加偏应力趋于零时自由能函数的不连续性和宏观塑性变形的不连续性。这一本构理论将能统一地描述在不同温度和载荷下记忆合金所呈现的各种行为。     

CONSTITUTIVE MODELING OF ROLLED SHAPE MEMORY ALLOY SHEETS TAKING INTO ACCOUNT PRE-TEXTURE AND ANISOTROPIC HARDENING

The drawing or rolling process endows polycrystal shape memory alloy with a crys- tallographic texture, which can result in macroscopic anisotropy. The main purpose of this work is to develop a constitutive model to predict the thermomechanical behavior of shape memory alloy sheets, which accounts for the crystallographic texture. The total macroscopic strain is decom- posed into elastic strain and macro-transformation strain under isothermal condition. Considering the transformation strain in local grains and the orientation distribution function of crystallo- graphic texture, the macro-transformation strain and the effective elastic modulus of textured polycrystal shape memory alloy are developed by using tensor expressions. The kinetic equation is established to calculate the volume fraction of the martensite transformation under given stress. Furthermore, the Hill＇s quadratic model is developed for anisotropic transformation hardening of textured SMA sheets. All the calculation results are in good agreement with experimental data, which show that the present model can accurately describe the macro-anisotropic behaviors of textured shape memory alloy sheets.     

Comparison of the rheology of polymer melts in shear,and biaxial and uniaxial extensions

The experimental properties of different polymer melts, polystyrene, high density polyethylene and low density polyethylene are compared for the first time in three different deformations: step shear, step biaxial extension and steady uniaxial extension. Properties of three other melts are also studied in step biaxial and shear experiments. For our comparative purposes some data of Laun and Winter from the literature are used, as well as new data reported here. In all the step strain experiments, the stresses can be factored into a time dependent relaxation modulus and a strain dependent damping function. The data are interpreted using a differential constitutive equation of Larson which satisfies this time-strain separability and has a single parameter that describes the strain softening character of the material. Results show that differences in the properties of the melts are most pronounced in uniaxial extension and least in biaxial extension. All melts follow the Doi-Edwards prediction relatively closely in biaxial extension. In uniaxial extension, the branched material shows a strong strain hardening effect although its shear and biaxial properties are similar to the other melts. The constitutive model gives a reasonably good fit to the data in all three deformations for unbranched materials for the same value of the adjustable parameter; the model, however, fails for the branched low density polyethylene.     

Evaluation of identification methods for YLD2004-18p

Four calibration methods have been evaluated for the linear transformation-based anisotropic yield function YLD2004-18p (Barlat, F., Aretz, H., Yoon, J.W., Karabin, M.E., Brem, J.C., Dick, R.E., 2005. Linear transformation-based anisotropic yield functions. Int. J. Plasticity 21, 1009–1039) and the aluminium alloy AA5083-H116. The different parameter identifications are based on least squares fits to combinations of uniaxial tensile tests in seven directions with respect to the rolling direction, compression (upsetting) tests in the normal direction and stress states found using the full-constraint (FC) Taylor model for 690 evenly distributed strain paths. An elastic–plastic constitutive model based on YLD2004-18p has been implemented in a non-linear finite element code and used in finite element simulations of plane-strain tension tests, shear tests and upsetting tests. The experimental results as well as the Taylor model predictions can be satisfactorily reproduced by the considered yield function. However, the lacking ability of the Taylor model to quantitatively reproduce the experiments calls for more advanced crystal plasticity models.     

Plasticity of formable all-metal sandwich sheets: Virtual experiments and constitutive modeling

The mechanical behavior of a metallic sandwich sheet material composed of two flat face sheets and two bi-directionally corrugated core layers is analyzed in detail. The manufacturing of the sandwich material is simulated to obtain a detailed unit cell model which accounts for the non-uniform thickness distribution and residual stresses associated with the stamping of the core layers. Virtual experiments are performed by subjecting the unit cell model to various combinations of bi-axial in-plane loading including the special cases of uniaxial tension, uniaxial compression, equi-biaxial tension and shear. The results demonstrate that the core structure’s contribution to the in-plane load carrying capacity of the sandwich sheet material is similar to that of the face sheets. The numerical results are also used to identify the effective yield surface and hardening response of both the core layer and the face sheets. An anisotropic yield function with linear pressure dependency is proposed to approximate the equal-plastic work surfaces for the core structure and face sheets. Furthermore, a new two-surface model with non-linear interpolation based on plastic work density is presented to describe the observed combined isotropic-distortional hardening of the core structure.     

拉扭复合加载下循环应力应变关系的研究

以拉扭簿壁管试件为研究对象,根据多轴临界面上的应力应变特性及多轴疲劳临界面法的结果,结合单轴循环应力应变关系,研究了多轴比例与非比例加载下的循环应力应变关系,推导出多应力应变关系模型,经拉扭复合比例与非比例物载试验难证,其预测结果与实测值相符合。     

Damage in edge cracking of rolled metal slabs

Materials get damaged under shear deformations. Edge cracking is one of the most serious damage to the metal rolling industry, which is caused by the shear damage process and the evolution of anisotropy. To investigate the physics of the edge cracking process, simulations of a shear deformation for an orthotropic plastic material are performed. To perform the simulation, this paper proposes an elasto-aniso-plastic constitutive model that takes into account the evolution of the orthotropic axes by using a bases rotation formula, which is based upon the slip process in the plastic deformation. It is found through the shear simulation that the void can grow in shear deformations due to the evolution of anisotropy and that stress triaxiality in shear deformations of (induced) anisotropic metals can develop as high as in the uniaxial tension deformation of isotropic materials, which increases void volume. This echoes the same physics found through a crystal plasticity based damage model that porosity evolves due to the grain-to-grain interaction. The evolution of stress components, stress triaxiality and the direction of the orthotropic axes in shear deformations are discussed.     

Roles of plastic spin in shear banding

In this paper, the effects of plastic spin on shear banding and simple shear are examined systematically. Three types of plastic constitutive model with plastic spin are considered: (i) a non-coaxial model in which the direction of the plastic strain rate depends on that of the stress rate; (ii) a strain-softening model based on the J₂ flow theory; and (iii) the pressure-sensitive porous plasticity model. All the constitutive models are formulated in viscoplastic forms and in conjunction with non-local concepts that have been recently focused and discussed. First, behavior in simple shear is examined by numerical analysee with the aforementioned constitutive models. Moreover, some experimental evidences for stress response to simple shear are shown; that is, several large torsion tests of metal tubes and bars are carried out. Next, finite element simulations of shear banding in plane strain tension are performed. A critical effect of plastic spin on shear banding is observed for the noncoaxial model, while an almost negligible effect is observed for the porous model. The identical effects of plastic spin are observed, whether nonlocality exists or not. Finally, we discuss the relationship between the behavior in simple shear and the shear band formation. It is emphasized that this is a critical issue in predicting shear banding in macroscopic grounds.