Electrochemical determination of some antidiabetic drugs for type 2 diabetic patients

Quantitative determination of rosiglitazone, pioglitazone, glimepiride and glyburide as antidiabetic drugs for type 2 diabetic patients was performed conveniently and economically using cyclic voltammetry (CV) and differential pulse voltammetry (DPV). Carbon paste (CPE) and glassy carbon (GCE) electrodes were successfully used as sensors for these drugs in Briton-Robinson (B-R) as buffer solution. The preparation of CPE and the GCE as ion selective electrodes is based on the construction of 10% standard drug ion pair with reineckate or tungstophosphate imbedded as electroactive material. Working standards were freshly prepared just before the assay by dilution from a 10⁻² mol L⁻¹ drug stock solution. At a scan rate of 100 mV s⁻¹ the cyclic voltammograms showed a well defined anodic peak with high selectivity. The DVP gave a reproducible well defined diffusion controlled peak for each drug at a scan rate of 10 mV s⁻¹. The oxidation peaks were used to determine the tested drug concentrations. The quantitative determination of the four drugs in their pharmaceutical preparations by the proposed electrochemical technique was found to be identical with the values obtained by the standard HPLC method. A mean % recovery of 100 ± 1 was obtained and the % relative standard deviation was 1.62 indicating the high precision of the method and the confidence in its repeatability. The proposed electroanalytical technique using either the CPE or the GCE is economic, selective and can be applied for both the qualitative and quantitative determination of the drugs in their pharmaceutical preparations, without special drug separation.     

A novel sensor based on electropolymerization of β-cyclodextrin and l-arginine on carbon paste electrode for determination of fluoroquinolones

An electrochemical sensor for fluoroquinolones (FQs) based on polymerization of β-cyclodextrin (β-CD) and l-arginine (l-arg) modified carbon paste electrode (CPE) (P-β-CD-l-arg/CPE) was built for the first time. Synergistic effect of l-arg and β-CD was used to construct this sensor for quantification of these important antibiotics. Scanning electron microscope (SEM) image shows that polymer of β-CD and l-arg has been successfully modified on electrode. Electrochemical impedance spectroscopy (EIS) and cyclic voltammograms (CV) further indicate that polymer of β-CD and l-arg efficiently decreased the charge transfer resistance value of electrode and improved the electron transfer kinetic between analyte and electrode. Under the optimized conditions, this modified electrode was utilized to determine the concentrations of ciprofloxacin, ofloxacin, norfloxacin and gatifloxacin. The differential pulse voltammogram (DPV) exhibits the oxidation peak currents were linearly proportional to their concentration in the range of 0.05–100 μM for ciprofloxacin, 0.1–100 μM for ofloxacin, 0.1–40 μM for norfloxacin and 0.06–100 μM for gatifloxacin, respectively. This method was also successfully used to detect the concentrations of each drug in pharmaceutical formulations and human serum samples. In addition, this proposed fluoroquinolones sensor exhibited good reproducibility, long-term stability and fast current response.     

Sensitive voltammetric determination of rutin at an ionic liquid modified carbon paste electrode

An ionic liquid modified carbon paste electrode (IL/CPE) had been fabricated by using hydrophilic ionic liquid 1-amyl-3-methylimidazolium bromide ([AMIM]Br) as a modifier. The IL/CPE was characterized by scanning electron microscope and voltammetry. Electrochemical behavior of rutin at the IL/CPE had been investigated in pH 3.29 Britton-Robinson (B-R) buffer solution by cyclic voltammetry (CV) and square wave voltammetry (SWV). The experimental results suggested that the modified electrode exhibited an electrocatalytic activity toward the redox of rutin. The electron transfer coefficient (α) and the standard rate constant (k_s) of rutin at the modified electrode were calculated. Under the selected conditions, the reduction peak current was linearly dependent on the concentration of rutin in the range of 4.0 × 10⁻⁸ to 1.0 × 10⁻⁵ mol L⁻¹ (r = 0.9998), with a detection limit of 1.0 × 10⁻⁸ mol L⁻¹ (S/N = 3). The relative standard deviation (R.S.D.) for six times successful determination of 8.0 × 10⁻⁷ mol L⁻¹ rutin was 1.2%. The proposed method was applied to determine rutin in tablet and urine sample. In addition, the IL/CPE exhibited a distinct advantage of simple preparation, surface renewal, good reproducibility and good stability.     

New automatized method with amperometric detection for the determination of azithromycin

A FIA-amperometric method for azithromycin determination was developed. A working glassy carbon electrode and a Ag/AgCl/NaCl (3 M) reference electrode were used. The determination is based on the electrochemical oxidation of the azithromycin at 0.9 V in Britton-Robinson buffer solution (pH 8.0). Due to the adsorption of the reaction products on the electrode surface, an effective cleaner cycle was implemented. By using the optimum chemical and FIA conditions, a concentration linear range of 1.0-10.0 mg L⁻¹ and a detection limit (LOD) of 0.76 mg L⁻¹ are obtained. The method was validated and satisfactorily applied to the determination of azithromycin in pharmaceutical formulations.     

Electrochemical behaviors of guanosine on carbon ionic liquid electrode and its determination

The electrochemical behaviors of guanosine on the ionic liquid of N-butylpyridinium hexafluorophosphate (BPPF₆) modified carbon paste electrode (CPE) was studied in this paper and further used for guanosine detection. Guanosine showed an adsorption irreversible oxidation process on the carbon ionic liquid electrode (CILE) with the oxidation peak potential located at 1.12 V (vs. SCE) in a pH 4.5 Britton-Robinson (B-R) buffer solution. Compared with that on the traditional carbon paste electrode, small shift of the oxidation peak potentials appeared but with a great increment of the oxidation peak current on the CILE, which was due to the presence of ionic liquid in the modified electrode adsorbed the guanosine on the surface and promoted the electrochemical response. The electrochemical parameters such as the electron transfer coefficient (α), the electron transfer number (n), and the electrode reaction standard rate constant (k_s) were calculated as 0.74, 1.9 and 1.26 × 10⁻⁴ s⁻¹, respectively. Under the optimal conditions the oxidation peak current showed a good linear relationship with the guanosine concentration in the range from 1.0 × 10⁻⁶ to 1.0 × 10⁻⁴ mol/L by cyclic voltammetry with the detection limit of 2.61 × 10⁻⁷ mol/L (3σ). The common coexisting substances showed no interferences to the guanosine oxidation. The CILE showed good ability to distinguish the electrochemical response of guanosine and guanine in the mixture solution. The urine samples were further detected by the proposed method with satisfactory results.     

On-line two-step stacking in capillary zone electrophoresis for the preconcentration of strychnine and brucine

An on-line sample preconcentration method by two-step stacking i.e., sweeping and micelle to solvent stacking, in capillary zone electrophoresis (CZE) has been developed for the determination of strychnine and brucine in traditional Chinese herbal medicines. After experimental optimizations, the best separation was achieved by using 75 mM phosphate buffer (pH 2.5) with 30% methanol (v/v). Compared with normal CZE injection, 51- and 38-fold improvement in concentration sensitivity was achieved for strychnine and brucine, respectively. The calibration curve was linear in the range of 0.1–5.0 μg mL⁻¹ for both strychnine and brucine, with the correlation coefficients of 0.9998 and 0.9997, respectively. The limits of detection (S/N = 3) for both alkaloids were 0.01 μg mL⁻¹. The inter-day (n = 8) and intra-day (n = 5) reproducibilities expressed as the relative standard deviations for corrected peak area were less than 9.5%. The method was applied to determine strychnine and brucine in two Chinese herbal medicines, with recoveries ranging from 94.2% to 105.4%. The results indicated that the method is simple, rapid, reliable, and can be applied to determine strychnos alkaloids in traditional Chinese herbal medicines.     

Determination of dye precursors in hair coloring products by liquid chromatography with electrochemical detection

The simultaneous determination of seven aminophenols, resorcinol and p-phenylenediamine in hair coloring products was performed by liquid chromatography (HPLC) with amperometric detection (ED). The aminophenols were separated on a ODS C18 reversed-phase column by isocratic elution with a mobile phase based on 0.1 M acetate buffer pH 4.5-methanol (90:10%, v/v) at a flow rate 0.8 mL min⁻¹. The limit of detection (S/N = 3) for the aminophenols was in the 15-40 pg (injected mass) range at an applied potential of 0.950 V versus Ag/AgCl. Peak heights for the aminophenols and the two others compounds were found to be linearly related to the amount injected, from 0.3 to 300 ng (r > 0.994-0.999).The relative standard deviation (R.S.D., n = 10) for 1 ng injected was comprised in the range from 2.5 to 6.2%, depending on the aminophenol tested. The present method minimizes troublesome and time-consuming pretreatment procedures and it was applied to the determination of aminophenols, resorcinol and phenylenediamine in hair coloring formulations.     

Using on-line solid phase extraction for flow-injection spectrophotometric determination of salbutamol

In the proposed procedure, the determination of salbutamol with Folin-Ciocalteau reagent (FC) using a flow injection analysis technique (FIA) with spectrophotometric detection at 750 nm is described. The lab-made FIA system consisted of a peristaltic pump Gilson Minipulse 3 equipped with Tygon tubes, double 6-port external Vici Valco sample injector and S 2000/SAD500 fiber optic spectrophotometer. It was controlled by a PC with use of originally compiled LabVIEW^®—supported software containing the mathematical library with various statistical functions for off-line data evaluation. Concentration, volume of reagents and flow rate were optimised by a simplex method. The proposed system was used for the direct determination of salbutamol sulphate in the tablets and the human urine without preliminary pre-treatment of the sample. The negative effect of interfering substances (excipients of the tablets and matrix of the urine) is overcome by a solid phase extraction (SPE), when salbutamol is adsorbed on the solid phase in the microcolumn, which is integrated directly into the flow system. Pre-treatment of the sample takes place directly in the flowing stream. The sample throughput without carryover of on-line SPE was 60-80 samples per hour. With the SPE column (Baker—carboxylic acid), salbutamol was determined in the linear range from 1 to 15 μg ml⁻¹ (R.S.D.=1.2%), with detection limit (3σ) 0.1 μg ml⁻¹ and a frequency of 40-60 samples per hour in the water solutions. The salbutamol was determined in the linear range from 2 to 20 μg ml⁻¹ (R.S.D.=1.7%), with detection limit (3σ) 1 μg ml⁻¹ and a frequency of 30 samples per hour in the samples of the human urine.     

Determination of bisphenol A and naphthols in river water samples by capillary zone electrophoresis after cloud point extraction

As a first attempt, cloud point extraction (CPE) was developed to preconcentrate bisphenol A (BPA), α-naphthol and β-naphthol prior to performing capillary zone electrophoresis (CZE) analysis. The parameters influencing the CPE efficiency, such as Triton X-114 concentrations, pH value, extraction time and temperature were systematically evaluated.After diluting with acetonitrile, the surfactant-rich phase of CPE can be injected directly into the CE instrument. The CZE baseline separation was achieved with running buffer (pH 9.5) composed of 50 mM sodium tetraborate in 30% (v/v) methanol, and an applied voltage of 25 kV. Under the optimized CPE and CZE conditions, an preconcentration factor of 50 times could be obtained and the limit of quantification for the three analytes were found to be 1.67 μg L⁻¹, 0.80 μg L⁻¹ and 0.67 μg L⁻¹ for BPA, α-naphthol and β-naphthol, respectively. The proposed methods have shown to be a green, rapid and effective approach for determination of three analytes present in river water samples.     

Voltammetric determination of 4-nitrophenol at a lithium tetracyanoethylenide (LiTCNE) modified glassy carbon electrode

The reduction of 4-nitrophenol (4-NP) has been carried out on a modified glassy carbon electrode using cyclic and differential pulse voltammetry (DPV). The sensor was prepared by modifying the electrode with lithium tetracyanoethylenide (LiTCNE) and poly-l-lysine (PLL) film. With this modified electrode 4-NP was reduced at −0.7 V versus SCE. The sensor presented better performance in 0.1 mol l⁻¹ acetate buffer at pH 4.0. The other experimental parameters, such as concentration of LiTCNE and PLL, pulse amplitude and scan rate were optimized. Under optimized operational conditions, a linear response range from 27 up to 23200 nmol l⁻¹ was obtained with a sensitivity of 3.057 nA l nmol⁻¹ cm⁻². The detection limit for 4-NP determination was 7.5 nmol l⁻¹. The proposed sensor presented good repeatability, evaluated in term of relative standard deviation (R.S.D.=4.4%) for n=10 and was applied for 4-NP determination in water samples. The average recovery for these samples was 103.0 (± 0.7)%.     

Microchip capillary electrophoresis with electrochemical detector for precolumn enzymatic analysis of glucose, creatinine, uric acid and ascorbic acid in urine and serum

An integrated multiple-enzymatic assay was performed on a (microchip capillary electrophoresis) μCE-EC chip capable of precise intake of sample or reagents in nanoliters. Incorporating multiple-enzyme assay into the μCE chip is relatively new—rendering simultaneous analysis of creatinine and uric acid a snap.Added to the list of merits in this study are the enhanced sensitivity down to 1 μM and a broader spectrum of analytes—inclusive of glucose for the long-time sufferers of diabetes. The performance was orchestrated to attain the claimed level: employing the end-channel electrode mode to tame the noises and the precolumn enzymatic reaction to stabilize the baseline. The 10 μm embedded Pt electrode, deposited at the end of the 30 μm wide separation channel, benefited chip fabrication besides noise reduction. The optimized conditions were 20 mM phosphate buffer (pH 7.5), +1.5 kV separation voltage and +1.0 V detection potential (versus Ag/AgCl). The migration time was repeatable within the deviation of 0.5% R.S.D. (n=7), but the peak currents ranged from 1.5 to 2.2% R.S.D. The detection limits (S/N=3) ranged from 0.71 μM for ascorbic acid to 10 μM for glucose. The calibration curve was linear from 10 to 800 μM (R²>0.995). Glucose, creatinine, uric acid and ascorbic acid as model analytes, in pure form or in serum and urine samples, were tested to verify its feasibility.     

Salting-out gradients in centrifugal partition chromatography for the isolation of chlorogenic acids from green coffee beans

In addition to sample solubility constraints, the use of polarity gradients in normal-phase centrifugal partition chromatography (CPC) for the purification of complex mixtures is also limited by the instability of biphasic systems as a consequence of dramatic changes in the settling times along the gradient, leading in many cases to column bleeding when working under maximum efficiency conditions. In this paper an electrostriction approach is proposed as a strategy in reversed-phase CPC to fractionate intermediate polarity extracts in a single run by bringing its components into the “sweet spot” in a controlled fashion through a stepwise reduction of salt concentration in the aqueous mobile phase. The salting-out gradient method was successfully tested with the separation of the major chlorogenic acids (CGAs, hydroxycinnamoylquinic acids) present in green coffee beans (5-caffeoylquinic acid (5-CQA), 5-feruloylquinic acid (5-FQA) and 3,5-dicaffeoylquinic acid (3,5-diCQA)) using ethyl acetate-hexane as the stationary phase and an ionic gradient of LiCl (5.0, 2.5 and 0.1 M) as the mobile phase in one case and (NH₄)₂SO₄/KNO₃ (3.0 and 1.5 M/1.5 M) in another. Regioisomers of each chlorogenic acid obtained by base-catalyzed isomerisation were also separated by CPC using isocratic elution. The best resolution for both FQAs and diCQAs was achieved with a chloroform–n-butanol–0.01 M pH 2.5 phosphate buffer (84:16:100; v/v) system, while CQAs were best isolated using chloroform–n-butanol–0.01 M pH 2.5 phosphate buffer/5.0 M LiCl (82:18:100; v/v).     

Determination of avermectins in commercial formulations using microemulsion electrokinetic chromatography

Microemulsion electrokinetic chromatography (MEEKC) was developed for quantitative analysis of avermectins, such as abamectin, doramectin and ivermectin, in commercial formulations, using the microemulsion buffer containing a 50 mM phosphate buffer at pH 2.5, 1.1% (v/v) n-octane as oil droplets, 180 mM sodium dodecylsulphate as surfactant, 890 mM 1-butanol as co-surfactant and 30% (v/v) ethanol as organic co-solvent. High accuracy and precision of the method were obtained. The contents of avermectins in commercial formulations determined by MEEKC were found to be insignificantly different with those determined by high performance liquid chromatography (HPLC). Therefore, MEEKC can be used an alternative method to HPLC for quantitative determination of avermectins.     

A detailed investigation for determination of tannic acid by anodic stripping voltammetry using porous electrochemical sensor

The electrochemical responses of tannic acid have been obtained at porous pseudo-carbon paste electrode (PPCPE), polypyrrole modified carbon paste electrode (PCPE), SBA-15 modified CPE (SBA-MCPE) and carbon paste electrode (CPE) under same conditions, respectively. The results show that the sensitivity of PPCPE is the highest among all the checked electrodes. The detection limit at PPCPE is 0.01 μM, which is about 10 times lower than that at CPE and is about 5 times lower than that at PCPE or SBA-MCPE. The developed electrode PPCPE possesses a few obvious advantages and no binding reagents are needed. The surface area of PPCPE is 59.26 m² g⁻¹ with pores ranging from 2 to 5 μm in diameter. The PPCPE is easy to preserve and has good reusability, which affords a nice electrochemical platform for detecting tannic acid.     

Separation of hypoviral double-stranded RNA on monolithic chromatographic supports

A procedure based on BIA Separations CIM DEAE anion-exchange chromatography was developed to separate double-stranded (ds) RNA of hypovirus infecting phytopathogenic fungus Cryphonectria parasitica. Using a linear gradient of 25 mM 4-morpholinepropanesulfonic acid (MOPS), pH 7.0 as a binding buffer, and 25 mM MOPS, 1.5 M NaCl, 0.1 mM EDTA, 15% isopropanol (v/v), pH 7.0 as an elution buffer, hypoviral dsRNA was additionally purified from nucleic acid species present in preparations partially purified by standard CF-11 cellulose chromatography. Moreover, crude phenol/chloroform extracts of the fungal tissue were also applied to monolithic supports and CIM DEAE chromatograms revealed clear evidence for hypoviral presence without CF-11 chromatography, nucleic acid precipitation, and electrophoresis.     

Determination of benorilate in pharmaceutical formulations and its metabolite in urine at carbon paste electrode modified by silver nanoparticles

Benorilate was determined by the differential pulse voltammetry (DPV) using a carbon paste electrode modified by silver nanoparticles in 1.25 × 10⁻³ mol l⁻¹ KH₂PO₄ and Na₂HPO₄ buffer solution (pH = 6.88, 25 °C) .The anodic peak potential was +0.970 V (versus SCE). A good linear relationship was realized between the anodic peak currents and benorilate concentrations in the range of 1.0 × 10⁻⁷ to 2.5 × 10⁻⁴ mol l⁻¹ with the detection limit of 1.0 × 10⁻⁸ mol l⁻¹. The recovery was 95.2-103.6% with the relative standard deviation of 3.6% (n = 9). The pharmaceutical preparations, benorilate tablets samples and its metabolite (salicylic acid) in urine were determined with the desirable results.     

Cloud point extraction preconcentration for capillary electrophoresis of metal ions

The application of the cloud point extraction (CPE) technique for capillary electrophoresis (CE) determination of metal ions was demonstrated using Cu(II) and Co(II) as model metal ions. The preconcentration of Cu(II) and Co(II) in aqueous solution was achieved by CPE with 1-(2-pyridylazo)-2-naphthol (PAN) as the chelating agent and Triton X-114 as the extractant. Baseline separation of the PAN chelates of Cu(II) and Co(II) was realized by CE with a photodiaode array detector in a  μm i.d. fused-silica capillary at 17 kV. A 50 mM NH₄Ac buffer solution (pH 8.0) containing 0.2 mM of PAN in 80% (v/v) of acetonitrile and 20% (v/v) doubly deionized water (DDW) was used as the separation medium to avoid the adsorption of hydrophobic substances and nonionic surfactant Triton X-114 onto the inner surface of the separation capillary, ensuring the separation efficiency and reproducibility. The precision (relative standard deviation (R.S.D.), n=5) for five replicate injections of a mixture of 20 μg/l of Co(II) and Cu(II) were 0.74 and 1.8% for the migration time, 3.1 and 0.64% for the peak area measurement, respectively. The apparent concentration factor, which is defined as the concentration ratio of the analyte in the final diluted surfactant-rich extract ready for CE separation and in the initial solution, was 15.9 for Co(II) and 16.3 for Cu(II). The linear concentration range was from 3 to 100 μg/l for both Co(II) and Cu(II). The detection limits of Co(II) and Cu(II) were 0.12 and 0.26 μg/l, respectively. The developed method was successfully applied to the determination of Co(II) and Cu(II) in tap water, snow water, and flavor wines.     

Cobalt phthalocyanine as a biomimetic catalyst in the amperometric quantification of dipyrone using FIA

A biomimetic sensor for the determination of dipyrone was prepared by modifying carbon paste with cobalt phthalocyanine (CoPc), and used as an amperometric detector in a flow injection analysis (FIA) system. The results of cyclic voltammetry experiments suggested that CoPc behaved as a biomimetic catalyst in the electrocatalytic oxidation of dipyrone, which involved the transfer of one electron. The optimized FIA procedure employed a flow rate of 1.5 mL min⁻¹, a 75 μL sample loop, a 0.1 mol L⁻¹ phosphate buffer carrier solution at pH 7.0 and amperometric detection at a potential of 0.3 V vs. Ag/AgCl. Under these conditions, the proposed method showed a linear response for dipyrone concentrations in the range 5.0 × 10⁻⁶-6.3 × 10⁻³ mol L⁻¹. Selectivity and interference studies were carried out in order to validate the system for use with pharmaceutical and environmental samples. In addition to being environmentally friendly, the proposed method is a sensitive and selective analytical tool for the determination of dipyrone.     

Voltammetric determination of L-dopa using an electrode modified with trinuclear ruthenium ammine complex (Ru-red) supported on Y-type zeolite

The L-dopa is the immediate precursor of the neurotransmitter dopamine. Unlike dopamine, L-dopa easily enters the central nervous system and is used in the treatment of Parkinson’s disease. A sensitive and selective method is presented for the voltammetric determination of L-dopa in pharmaceutical formulations using a carbon paste electrode modified with trinuclear ruthenium ammine complex [(NH₃)₅Ru^IIIORu^IV(NH₃)₄ORu^III(NH₃)₅]⁶⁺ (Ru-red) incorporated in NaY zeolite. The parameters which influence on the electrode response (paste composition, potential scan rate, pH and interference) were also investigated. The optimum conditions were found to an electrode composition (m/m) of 25% zeolite containing 6.7% Ru, 50% graphite and 25% mineral oil in acetate buffer at pH 4.8. Voltammetric peak currents showed a linear response for L-dopa concentration in the range between 1.2×10⁻⁴ and 1.0×10⁻² mol l⁻¹ (r=0.9988) with a detection limit of 8.5×10⁻⁵ mol l⁻¹. The variation coefficient for a 1.0×10⁻³ mol l⁻¹ L-dopa (n=10) was 5.5%. The results obtained for L-dopa in pharmaceutical formulations (tablet) was in agreement with compared official method. In conclusion, this study has illustrated that the proposed electrode modified with Ru-red incorporated zeolite is suitable valuable for selective measurements of L-dopa.     

Voltammetric determination of Celiptium with carbon paste and lipid-modified carbon paste electrodes

The electrooxidation of the antitumour drug 2-methyl-9-hydroxyellipticinium (Celiptium) was investigated by cyclic, differential-pulse and adsorptive voltammetry at carbon paste (CPE) and lipid-modified carbon paste electrodes (LM-CPE). The influence of the paste composition, i.e., the ratio of graphite to binder, was studied in order to elucidate the nature of the accumulation process at the surface of the CPE. The electrode surface coverage at saturation was calculated. A.c. measurements at the CPE and at the LM-CPE during the accumulation of Celiptium demonstrated an increased differential double layer capacity of the LM-CPE. The influence of several parameters that affect the adsorptive step at the CPE was investigated, such as pH, ionic strength and interfering ions. Improved signals were obtained at the CPE and the detection limit in 0.1 M sodium perchlorate (t_acc.=3 min) was found to be 2 × 10^?10 M. Measurements of the drug in dilute standard serum samples were done using the medium-exchange technique.