用于燃料电池质子交换膜的含萘及氮杂环结构的新型磺化聚酰亚胺的合成及性能

将自制的4,4'-二氨基二苯醚-2,2'-二磺酸基(ODADS)、 含氮杂环芳香二胺1,2-二氢-2-(4-氨基苯基)-4-[4-(4-氨基苯氧基)-苯基]-二氮杂萘-1-酮(DHPZ-DA)和1,4,5,8-萘四甲酸二酐(NTDA)进行直接缩合聚合反应, 通过改变磺化二胺单体的含量来改变聚合物的磺化度, 成功地合成了一系列高分子量的不同磺化度的六元环聚酰亚胺(SPIs), 其特性粘度在0.55-1.47 dL/g. 采用FTIR和 1H NMR技术表征了聚合物的结构. 研究了经溶液浇铸成磺化聚合物膜的理化性质. 结果表明, 随着聚合物磺化度的增大, 膜的含水率和离子交换能力增大, 尺寸稳定性、 对水的稳定性以及抗氧化性降低.     

新型氯取代含杂萘联苯结构可溶性聚芳酰胺的合成、表征和性能

以类双酚单体4-(3-氯-4-羟基-苯基)-2H-二氮杂萘-1-酮(DHPZ-OC)和对氯苯腈为原料进行亲核取代反应合成二腈化合物4-[3-氯-4-(4-氰基苯氧基)苯基]-2-(4-氰基苯基)二氮杂萘-1-酮(),然后在碱性(KOH)条件下进行水解制得了一种新型的含氯取代杂萘联苯结构的芳香二酸,4-[3-氯-4-(4-羧基苯氧基)苯基]-2-(4-羧基苯基)二氮杂萘-1-酮().用新二酸与各种芳香二胺进行直接缩合聚合制得了一系列新型氯取代含杂萘联苯结构的聚芳酰胺,特性粘度可达1.23dL/g.用FTIR和¹HNMR研究了新型二酸单体及聚合物的结构.该类聚芳酰胺均可溶解于NMP,DMAc和DMSO等极性有机溶剂中,并且可浇铸成透明韧性膜,其玻璃化转变温度在291～332℃之间,10%的热失重温度在460℃以上.     

含二苯甲烷结构四元共缩聚杂萘聚芳酰胺的合成与性能

采用自制二胺1,2-二氢-2-(4-氨基苯基)-4-[4-(4-氨基苯氧基)-苯基]-二氮杂萘-1-酮、商品二胺4,4′-二氨基二苯甲烷和对苯二胺与对苯二甲酰氯进行低温溶液缩聚反应,改变三种二胺的比例,得到了一系列共聚酰胺树脂,其特性粘数为1·24~2·32dL/g,用FT-IR、1H-NMR手段研究了聚合物的结构;利用DSC和TGA研究了聚合物的耐热性能,结果表明,该类聚合物具有较高玻璃转化温度(301℃以上);氮气气氛中5%热失重温度在438℃以上;用一定比例的二胺制得的聚合物分别能溶于N-甲基吡咯烷酮、N,N-二甲基乙酰胺等非质子极性溶剂中并浇注得到韧性薄膜.     

含联苯二氮杂萘酮结构聚芳酰胺的合成与表征

用类双酚单体4[4(4羟基苯基)苯基]2H二氮杂萘1酮(DHPZpP)与对氯苯腈进行亲核取代反应后碱性水解合成一种扭曲、非共平面杂环芳香二酸,4{4[4(4羧基苯氧基)苯基]苯基}2(4羧基苯基)二氮杂萘1酮(2).由二酸2和各种芳香二胺进行膦酰化缩聚反应制得了一系列的含联苯二氮杂萘酮结构聚芳酰胺,其特性粘数在0.42～0.72dLg之间.该类聚芳酰胺均可溶解于NMP、DMAc和DMSO等极性有机溶剂中,并且可用DMAc为溶剂制成具有良好机械性能的透明聚合物薄膜,聚合物薄膜的拉伸强度为80～89MPa.该类聚芳酰胺具有优异的耐热性,玻璃化转变温度Tg在298～328℃之间,10%的热失重温度(Td)在470℃以上.     

含3,5-二甲基二氮杂萘酮联苯结构聚醚酰亚胺的合成与性能

由4-[(3,5-二甲基-4-羟基)苯基]-2,3-杂萘-1-酮与4-氯-N-苯基邻苯酰亚胺通过亲核取代反应、水解反应和脱水反应合成了一种新型不对称含二氮杂萘联苯结构的二酐单体,并对其进行结构表征.由新型二酐单体与市售的二胺单体通过“一步法”溶液聚合反应合成了5种含二氮杂萘酮联苯结构的聚醚酰亚胺.通过FTIR和¹HNMR方法研究了聚合物的结构及性能.结果表明,该类聚合物既具有较高的耐热性能,又可以在室温下溶解于非质子极性溶剂,如N-甲基吡咯烷酮和间甲酚等.     

含甲基磺化杂萘联苯聚醚砜酮质子交换膜材料的合成与性能

以4-(3,5-二甲基-4-羟基苯基)2,3-二氮杂萘-1-酮,3,3′-二磺酸钠-4,4′-二氟苯甲酮和4,4′-二氯二苯砜为原料,利用亲核缩聚反应,通过改变磺化单体的含量,制备出一系列不同磺化度的杂萘联苯聚醚砜酮(SPPESK-DM).采用FTIR、1H-NMR表征了聚合物的结构,热失重分析仪研究了聚合物的耐热稳定性,以N-甲基-2-吡咯烷酮为溶剂采用溶液浇铸法成膜研究该系列聚合物膜的性能.结果表明,SPPESK-DM磺酸基的热分解温度在260℃以上,主链分解温度在410℃以上;膜的吸水率、溶胀率、离子交换容量和质子传导率均随着磺化度的增大而增大,磺化度为1.0的SPPESK-DM50的质子传导率达到1.08×10-2S/cm(85℃),且甲醇渗透系数为2.06×10-7cm2/s,低于Nafion117膜的甲醇渗透系数(2×10-6cm2/s).此系列膜的耐氧化性比较优异,可望用于质子交换膜燃料电池中.     

含全氟联苯结构的磺化聚二氮杂萘酮醚氧膦质子交换膜的制备与性能

将全氟联苯、 二(4-氟苯基)苯基氧膦与4-(4′-羟基)苯基-2,3-二氮杂萘酮共聚, 合成了含全氟联苯结构的聚二氮杂萘酮醚氧膦, 再经磺化反应, 制备了含全氟联苯结构的磺化聚二氮杂萘酮醚氧膦(sPEPOF-x, x为含氟重复单元的摩尔分数)质子交换膜. 由于强疏水全氟联苯结构促进了聚合物膜的亲水/疏水微相分离, 提高了质子电导率, 降低了溶胀率, sPEPOF质子交换膜表现出优良的综合性能. 在80 ℃下, sPEPOF-25质子交换膜的溶胀率仅为10%, 约为Nafion 117的一半, 而其电导率为0.099 S/cm, 约为Nafion 117的1.2倍, 且耐氧化稳定性好, 热稳定性高, 具有潜在的应用前景.     

新型萘酐型磺化聚酰亚胺质子交换膜的合成

以新型磺化二胺单体, 1,4-双(4-胺基-2-磺酸基苯氧基)苯(DS-TBDA)与非磺化单体1,4′-二胺基二苯醚（ODA）、 1,4,5,8-萘四酸二酐(NTDA)为原料, 采用高温聚合法, 制备了一系列具有不同磺化度的萘酐型磺化聚酰亚胺(S-PI)质子交换膜材料, 并研究了材料性能与结构的关系. 磺化度超过33%时, 质子传导率可达到与Nafion膜同一数量级的水平, 而甲醇透过率均在2.85×10-7 cm2/s以下, 比Nafion膜低1-2个数量级. 研究结果表明, 该膜有望在直接甲醇燃料电池(DMFC)中获得应用.     

苯取代杂萘联苯型聚芳酰胺的合成与表征及性能

合成了一种新型苯基取代芳香二胺双 (4 胺基苯基 ) 4 (3 苯基 4 苯氧基 ) 2 ,3 二氮杂萘 1 酮 (2 (4 aminophenyl) 4 (3 pheny 4 phenoxy) 2 ,3 phthalazinone 1) (1,DAPPP) .采用Yamazaki体系 ,二胺单体 1能与各种商品芳香二酸进行溶液亲核缩聚反应 ,制得了一类新型苯基取代聚芳酰胺 ,其特性粘度为 0 .6 3～ 0 .75dL·g- 1 ;以MS、FT IR、1 H NMR等分析手段研究了新型二胺单体及其聚合物的结构 ;利用DSC、TGA研究了聚合物的耐热性能 ,结果表明新型聚芳酰胺具有高的玻璃化温度 (32 0 .9～ 32 9.9℃ ) ,氮气氛中 10 %热失重温度在40 5 .3℃以上 ,聚合物在二甲基乙酰胺、1 甲基吡咯烷酮和间甲酚等极性有机溶剂中可溶解并浇注得到韧性薄膜     

磺化侧苯基杂萘联苯聚醚酮酮的合成与性能

以4-(3-苯基-4-羟基苯基)-2,3-二氮杂萘-1-酮(DHPZ-P)、 4-(4-羟基苯基)-2,3-二氮杂萘-1-酮(DHPZ)和1,4-二(4'-氟苯甲酰基)苯(BFBB)为原料, 经溶液亲核取代缩聚反应, 通过调节DHPZ-P和DHPZ的比例, 合成了一系列侧苯基杂萘联苯聚醚酮酮(PPEKK-P), 然后以浓硫酸为磺化剂, 制备出一系列磺化侧苯基杂萘联苯聚醚酮酮(SPPEKK-P). 利用傅里叶变换红外光谱(FTIR)和氢核磁共振谱(¹H NMR)对聚合物结构进行表征, 结果表明, 磺酸基团引入到聚合物链的侧苯基上. 采用溶液浇铸法制备SPPEKK-P质子交换膜. SPPEKK-P膜的吸水率、 溶胀率和质子传导率均随离子交换容量(IEC)的增加而增加, 且具有较好的耐氧化性. IEC最高的SPPEKK-P-100膜的质子传导率在95℃能达到7.44×10^-2 S/cm, 且甲醇渗透系数为5.57×10^-8 cm²/s, 阻醇性能优于Nafion117膜.     

Synthesis and properties of novel sulfonated polyimides containing phthalazinone moieties for PEMFC

A novel sulfonated diamine, 1,2-dihydro-2-(3-sulfonic-4-aminophenyl)-4-[4-(3-sulfonic-4-aminophenoxy)-phenyl]-phthalazin-1-one(S-DHPZDA), was successfully synthesized and two series of six-membered sulfonated polyimides (SPIs) were prepared from 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTDA), S-DHPZDA, and nonsulfonated diamines DHPZDA or 4,4′-diaminodiphenyl ether (ODA). The chemical structure of the S-DHPZDA and the SPIs were characterized by ¹H NMR and FT-IR. Tough, brownish and transparent membranes were cast from SPIs’ solution in NMP. The water uptake, swelling ratio, chemical and thermal stability, hydrolytic and oxidative stability as well as proton conductivity of these new polymers were investigated systematically. Compared with Nafions, the obtained SPI membranes have onset decomposed temperatures of these two series SPIs were above 318 °C and decomposed temperature of main chain were 565 °C and excellent dimension stabilities on similar IECs. Introduction of phthalazinone moieties had improved the copolyimides’ solubility in polar aprotic organic solvents like m-cresol, NMP, DMSO, DMF etc. The SPIs had high proton conductivity (σ) in the order of magnitude of 10⁻³ to 10⁻² S cm⁻¹ depending on the degree of sulfonation (DS) of the polymers.     

Synthesis and characterization of novel sulfonated polyimide containing phthalazinone moieties as PEM for PEMFC

A novel sulfonated diamine monomer,1,2-dihydro-2-(3-sulfonic-4-aminophenyl)-4-[4-(4-aminophenoxy)-phenyl]phthalazin- 1-one(S-DHPZDA),was successfully synthesized by direct sulfonation of diamine 1,2-dihydro-2-(4-aminophenyl)-4-[4-(4- aminophenoxy)-phenyl]-phthalazin-1-one(DHPZDA).A series of sulfonated polyimides(SPIs),which can be used as the material of the proton exchange membrane(PEM)for the proton exchange membrane fuel cell(PEMFC),were prepared from 1,4,5,8- naphthalenetetracarboxylic dianhydride(NTDA),S-DHPZDA,and nonsulfonated diamines DHPZDA.The structure of the monomer and polymers were characterized by FT-IR and~1H NMR.The solubility of the S-DHPZDA-based SPIs has been improved due to the induction of the phthalazione moiety.The SPIs membranes have high thermo-stability,predominant swelling resistance with high ion exchange capacity.     

Sulfonated polyimides containing pyridine groups as proton exchange membrane materials

A series of sulfonated polyimides(SPIs) containing pyridine groups were prepared by direct polycondensation from 1,4,5,8-naphthalenetetracarboxylic dianhydride(NTDA),4,4’-diaminodiphenyl ether-2,2’-disulfonic acid(ODADS) and 4-(4-methoxy)phenyl-2,6-bis(4-aminophenyl)pyridine(DAM).The resulting copolymers displayed good solubility in common organic solvents.Flexible,transparent,tough membranes were obtained via solution casting.All the films showed high thermal stability with desulfonation temperature over 300℃.They exhibited prominent mechanical properties with Young’s modulus around 2.0 GPa.High proton conductivity(0.23 S/cm at 100%RH) was also observed.More importantly, the new materials exhibited low water uptake(30 wt%-75 wt%at 80℃) and improved water stability,which were attributed to the acid-base interaction between sulfonic acid and pyridine functional groups.     

Synthesis, water stability and proton conductivity of novel sulfonated polyimides from 4,4′-bis(4-aminophenoxy)biphenyl-3,3′-disulfonic acid

A novel sulfonated diamine monomer, 4,4′-bis(4-aminophenoxy)biphenyl-3,3′-disulfonic acid (BAPBDS) with the high basisity and flexible structure was synthesized by direct sulfonation of 4,4′-bis(4-aminophenoxy)biphenyl (BAPB). Sulfonated polyimides (SPIs) were prepared from 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTDA), BAPBDS and nonsulfonated diamines such as BAPB. The SPI membranes showed much higher water stability at high temperatures than other sulfonated diamine-based SPIs reported so far. Their water vapor sorption isotherm, water uptake (WU), density, dimensional change and proton conductivity σ were investigated. The SPIs showed rather isotropic dimensional changes with WU and the volume increases were slightly smaller than those estimated from the additivity. The SPIs with ion exchange capacities (IECs) of 1.9–2.7 meq/g displayed the similar relationship between σ and WU each other, which was different from those of Nafion 117 and also of the SPIs with the lower IECs. The former SPIs showed reasonably high σ values of 10⁻² S/cm or more even at WU of 25 g/100 g dry polymer under 70% RH at 50 °C, whereas the latter showed the similarly high σ values only in liquid water, but not in the nearly saturated water vapor.     

New polypyromellitimide films based on cyclotriphosphazene and bisaspartimide derived diamines

Three new thermally stable polypyromellitimide films were made by the thermal cyclodehydration of the corresponding polyamic acids obtained by the polymerization of pyromellitic dianhydride with 4,4′-bis{N²-[4-(4-aminobenzyl)phenyl]aspartimido} diphenylmethane, 4,4′-bis{N²-[4-(4-aminophenoxy)phenyl]aspartimido} diphenylether, and bis(4-aminophenoxy)tetrakis (4-phthalamic acid phenoxy)cyclotriphosphazene. The bis(4-aminophenoxy)tetrakis (4-phthalamic acid phenoxy)cyclotriphosphazene was obtained from hexakis(4-aminophenoxy)cyclotriphosphazene involving its reaction with phthalic anhydride. The structure of these materials and precursors were characterized by using Fourier-transform-infrared (FT–IR) and proton nuclear magnetic resonance spectroscopy. The thermal stabilities of the films were evaluated by the thermogravimetric analysis, showing char yields at 800°C ranging from 68% to 58% in a nitrogen atmosphere and 24% in air atmosphere.     

Synthesis and Characterization of Novel Sulfonated Polyimides from 4,6-Bis（4-aminophenoxy）-naphthalene-2-sulfonic Acid

A novel sulfonated diamine monomer, 4,6-bis（4-arninophenoxy）-naphthalene-2-sulfonic acid（BAPNS）, was synthesized. A series of sulfonated polyimide copolymers was prepared from BAPNS, 1,4,5,8-naphthalenetetracarboxylic dianhydride（NTDA） and nonsulfonated diamine 4,4＇-diaminodiphenyl ether（ODA）. Flexible, transparent, and mechanically strong membranes were obtained. The novel sulfonated polyimide（SPI） membranes show higher conductivity, for example, SPI-100 shows a conductivity of 0.0698 S/cm at 80℃（SPI-X： Xrefers to molar fraction of BAPNS）. The membranes exhibit the permeability of methanol from 2.18×10^-7 cm2/s to 2.57×10^-7 cm2/s, which is much lower than that of Nafion（2.00×10 6 cm^2/s）. The copolymers were thermally stable up to 330℃. The sulfonated polyimide copolymers also show reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 100%（molar fraction） BAPNS is 1.35 GPa under high moisture condi- tions. The optimum concentration of BAPNS was found to be 100%（molar fraction） from the view point of proton conductivity, methanol permeability, and membrane stability.     

Synthesis and characterization of sulfonated naphthalenic polyimides based on 4,4′-diaminodiphenylether-2,2′-disulfonic acid and bis[4-(4-aminophenoxy)phenylhexafluoropropane] for fuel cell applications

The paper describes the synthesis and characterization of sulfonated polyimides based on 1,4,5,8-naphthalene tetracarboxylic dianhydride (NTDA), 4,4′-diaminodiphenylether-2,2′-disulfonic acid (ODADS) and (bis[4-(4-aminophenoxy)phenylhexafluoropropane] (BDAF)). Several copolymer samples were prepared by varying the molar ratio of ODADS: BDAF (0.5:1.50, 0.75:1.25, 1:1 and 1.50: 0.5) in the initial monomer feed. Structural characterization of the copolymers was done using FT-IR and ¹H NMR. ¹H NMR was also used to calculate the copolymer composition. Thermal characterization was done using thermogravimertry and dynamic mechanical analysis. Polymer films were prepared by solution casting using m-cresol as solvent. The membranes thus prepared were characterized for water uptake, water stability, methanol permeability and proton conductivity. The obtained sulfonated polyimides (SPI’s) had proton conductivities in the range of 0.137-3.94 mS/cm. SPI’s with 50% degree of sulfonation had proton conductivity comparable to that of Nafion with methanol permeability lower than that of Nafion. It was found that the degree of sulfonation of polyimide had a large effect on the thermal stability, water uptake, ion-exchange capacity and proton conductivity.     

Structural modifications in imide-aryl ether phenylquinoxaline random copolymers

A rigid rod polyimide derived from biphenyldianhydride (BPDA) and p-phenylenediamine (PDA) was modified by the incorporation of diamines containing performed phenylquinoxaline and aryl ether linkages, and the morphology and mechanical properties of the resulting imide-aryl ether phenylquinoxaline copolymers were investigated. These phenylquinoxaline containing diamines, 1, 4-bis[6-(3-aminophenoxy)-3-phenyl-2-quinoxalinyl] benzene and 1, 4-bis[6-(4-aminophenoxy)-3-phenyl-2-quinoxalinyl] benzene, were prepared by a novel nucleophilic aromatic substitution reaction of 1,4-(6-fluoro-3-phenyl-2-quinoxalinyl) benzene with either 1, 3- or 1, 4-aminophenol in the presence of K₂CO₃, respectively. The diamines were utilized as co-monomers with BPDA and PDA to synthesize poly(amicacids.) Films were cast and cured (350°C) to effect imidization, affording films which showed high elongations and moduli. The copolymers with high phenylquinoxaline compositions displayed T_g's in the 300°C range, and the thermal stability of the copolymers was comparable to that of the parent polyimide. The copolymers also showed improved auto- or self-adhesion, particularly those which showed a T_g, allowing sufficient molecular motion for interdiffusion.