The fabrication of TiO<Subscript>2</Subscript> nanoparticle/ZnO nanowire arrays bi-filmed photoanode and their effect on dye-sensitized solar cells

Porous TiO₂ nanoparticles coated on ZnO nanowire arrays (TiO₂ NP/ZnO NW) as photoanode for dye-sensitized solar cell (DSSC) has been fabricated and investigated to improve the power conversion efficiency. The TiO₂ NP/ZnO NW photoanode consists of single crystalline ZnO NWs synthesized via hydrothermal method and porous TiO₂ NP film covered on the surface of ZnO NW arrays by screen printing technique. The effect of TiO₂ NPs thickness of the bi-filmed photoanode on the cell performance has been investigated, and TiO₂ NP/ZnO NW DSSC with NP thickness of ~5 μm exhibits the best efficiency of 4.68%, higher than 1.16% of ZnO NW DSSC and 3.18% of TiO₂ NPs DSSC, prepared and tested under identical conditions. The efficiency increase is attributed to the enlarged photocurrent, due to the greatly enhanced surface area for dye absorption and light harvesting efficiency resulted from TiO₂ NPs, and improved open-circuit voltage, due to reduced electron recombination by providing direct conduction pathway along ZnO NWs.     

Preparation of highly ordered TiO2 nanotubes on Ti-foil for dye-sensitized solar cells

TiO₂ nanotube arrays were grown on Ti foil in mixed electrolyte by the anodizing process. TiO₂ nanotube arrays were immersed in the TiCl₄ solution to improve the photocurrent by enhanced charge transfer between TiO₂ and dye molecules on the activity surface. Internal resistance of dye-sensitized solar cells (DSSC) was measured by impedance spectroscopy measurements. Backside illuminated DSSC with TiCl₄-treated TiO₂ nanotubes exhibited a conversion efficiency of 1.45% and showed improved electron transfer.     

Preparation of a nanoporous CaCO3-coated TiO2 electrode and its application to a dye-sensitized solar cell

A nanoporous CaCO3 overlayer-coated TiO2 thick film was prepared by the topotactic thermal decomposition of Ca(OH)2, and its performance as an electrode of a dye-sensitized solar cell was investigated. As compared to bare TiO2, nanoporous CaCO3-coated TiO2 provided higher specific surface area and, subsequently, a larger amount of dye adsorption; this in turn increased short-circuit current (Jsc). Furthermore, the CaCO3 coating demonstrated increased impedance at the TiO2/dye/electrolyte interface and increased the lifetime of the photoelectrons, indicating the improved retardation of the back electron transfer, which increases Jsc, open-circuit voltage (Voc), and fill factor (ff). Thereby, the energy conversion efficiency (eta) of the solar cell improved from 7.8 to 9.7% (an improvement of 24.4%) as the nanoporous CaCO3 layer was coated onto TiO2 thick films.     

A Novel Improved Method to Increase the Efficiency of Dye‐Sensitized Solar Cells

A novel improved method which employs a reflective mirror at the back of the Pt counter electrode is used in dye‐sensitized solar cells (DSSC). The direction of the light propagation in the cells was changed because of adding a mirror and the light reflected back into the DSSC in order to enhance the optical absorption of the DSSCs. Therefore, the performance of the cells was improved distinctively. The TiO₂ electrodes were characterized by X‐ray diffraction, scanning electron microscopy and I‐V properties of the cells measured by Linear Sweep Voltammetry system. The results indicates that the conversion efficiency can be increased from 4.81% to 5.43% under AM 1.5 illumination when a mirror is added at the back of the Pt counter electrode in the same cell. Meanwhile, the Jsc, Voc and the fill factor can be obtained 18.65 mA/cm², 0.728 V and 0.561, respectively.     

Structurally Stabilized Organosilane‐Templated Thermostable Mesoporous Titania

Structurally thermostable mesoporous anatase TiO₂ (m‐TiO₂) nanoparticles, uniquely decorated with atomically dispersed SiO₂, is reported for the first time. The inorganic Si portion of the novel organosilane template, used as a mesopores‐directing agent, is found to be incorporated in the pore walls of the titania aggregates, mainly as isolated sites. This is evident by transmission electron microscopy and high‐angle annular dark field scanning transmission electron microscopy, combined with electron dispersive X‐ray spectroscopy. This type of unique structure provides exceptional stability to this new material against thermal collapse of the mesoporous structure, which is reflected in its high surface area (the highest known for anatase titania), even after high‐temperature (550 °C) calcination. Control of crystallite size, pore diameter, and surface area is achieved by varying the molar ratios of the titanium precursor and the template during synthesis. These mesoporous materials retain their porosity and high surface area after template removal and further NaOH/HCl treatment to remove silica. We investigate their performance for dye‐sensitized solar cells (DSSCs) with bilayer TiO₂ electrodes, which are prepared by applying a coating of m‐TiO₂ onto a commercial titania (P25) film. The high surface area of the upper mesoporous layer in the P25–m‐TiO₂ DSSC significantly increases the dye loading ability of the photoanode. The photocurrent and fill factor for the DSSC with the bilayer TiO₂ electrode are greatly improved. The large increase in photocurrent current (ca. 56 %) in the P25–m‐TiO₂ DSSC is believed to play a significant role in achieving a remarkable increase in the photovoltaic efficiency (60 %) of the device, compared to DSSCs with a monolayer of P25 as the electrode.     

Effects of Nanocrystalline Porous TiO2 Films on Interface Adsorption of Phthalocyanines and Polymer Electrolytes in Dye-Sensitized Solar Cells

Summary: We have synthesized three kinds of titanylphthalocyanines with different crystal structures (TiOPcs; PcT2000R, PcT3000R, and PcT1100S) and analyzed their crystal structure by X-ray Diffraction (XRD), Fourier transfer IR (FT-IR) spectroscopy, and Transmission Electron Microscope (TEM). From experimental results, we have confirmed that PcT2000R was estimated to be alpha-form; PcT3000R was beta-form, and PcT1100S was gamma-form. Quasi-solid state dye-sensitized solar cell (DSSC) devices were prepared with a polymer electrolyte using TiOPcs as a co-adsorbent. The DSSC device using TiOPc has higher power conversion efficiency than without TiOPc, due to decrease of electron transfer distance by the interface adsorption between TiO₂ film and polymer electrolyte. Also, we have studied the effects of the crystal structures of TiOPcs on the property of polymer electrolyte and the performance of the DSSC device. The best result on power conversion efficiency was 7.13% in DSSC device using PcT3000R having its highest stability. The open-circuit voltage (V_oc) was 0.69 V, the short-circuit current density (J_sc) was 20.02 mA/cm², and the Fill Factor (FF) was 0.52. the addition of TiOPc as co-adsorbent is useful for improve to the performances of DSSC devices such as V_oc, J_sc, and power conversion efficiency.     

Hydrothermal Synthesis of a Crystalline Rutile TiO2 Nanorod Based Network for Efficient Dye‐Sensitized Solar Cells

One‐dimensional (1D) TiO₂ nanostructures are desirable as photoanodes in dye‐sensitized solar cells (DSSCs) due to their superior electron‐transport capability. However, making use of the DSSC performance of 1D rutile TiO₂ photoanodes remains challenging, mainly due to the small surface area and consequently low dye loading. Herein, a new type of photoanode with a three‐dimensional (3D) rutile‐nanorod‐based network structure directly grown on fluorine‐doped tin oxide (FTO) substrates was developed by using a facile two‐step hydrothermal process. The resultant photoanode possesses oriented rutile nanorod arrays for fast electron transport as the bottom layer and radially packed rutile head‐caps with an improved large surface area for efficient dye adsorption. The diffuse reflectance spectra showed that with the radially packed top layer, the light‐harvesting efficiency was increased due to an enhanced light‐scattering effect. A combination of electrochemical impedance spectroscopy (EIS), dark current, and open‐circuit voltage decay (OCVD) analyses confirmed that the electron‐recombiantion rate was reduced on formation of the nanorod‐based 3D network for fast electron transport. As a resut, a light‐to‐electricity conversion efficiency of 6.31 % was achieved with this photoanode in DSSCs, which is comparable to the best DSSC efficiencies that have been reported to date for 1D rutile TiO₂.     

Dye sensitization of a large band gap semiconductor by an iron(III) complex

The Fe(III) complex, [Fe^III(HQS)₃] (HQS = 8-hydroxyquinoline-5-sulfonic acid), is found to effect sensitization of the large band gap semiconductor, TiO₂. The role of interfacial electron transfer in sensitization of TiO₂ nanoparticles by surface adsorbed [Fe^III(HQS)₃] was studied using femtosecond time scale transient absorption spectroscopy. Electron injection has been confirmed by direct detection of the electron in the conduction band. A TiO₂-based dye-sensitized solar cell (DSSC) was fabricated using [Fe^III(HQS)₃] as a sensitizer, and the resulting DSSC exhibited an open-circuit voltage value of 425 mV. The value of the short-circuit photocurrent was found to be 2.5 mA/cm². The solar to electric power conversion efficiency of the [Fe^III(HQS)₃] sensitized TiO₂-based DSSC device was 0.75 %. The results are discussed in the context of sensitization of TiO₂ by other Fe(II)-dye complexes.     

基于TiO2纳米管阵列的高效正面透光型染料敏化太阳能电池的制备及其光电性能

报道了一种基于TiO2纳米管(TNT)阵列正面透光型光阳极的高效染料敏化太阳能电池.将TNTs在450°C烧结后能避免其有序结构在HF处理过程中被破坏,使膜内高速电子传输通道被保留,有利于染料敏化太阳能电池(DSSC)实现高速电荷传输.再用HF、TiCl4、HF和TiCl4混合等溶剂对TNTs进行处理,提高其表面粗糙度以吸附更多染料.染料吸附量的增加能提高光阳极在300-570 nm波段光子捕获效率,该波段是染料吸收光子的主要区域.然而,在染料吸收光子较弱的长波段区域(570-800 nm)光子捕获效率的增加主要源于光阳极光散射率的提高.光阳极光子捕获效率的提高使DSSC的内外量子效率在全波段(300-800 nm)均有所增加,从而使短路电流明显提高.从电化学阻抗数据可知,与电子传输性能密切相关的电化学参数如电荷传输电阻、界面电荷复合电阻、电容、电子寿命、电子扩散长度和电子收集效率等在含处理过的TNTs光阳极DSSC中均有所改善,从而提高电池光电转换效率.含HF和TiCl4混合溶剂处理TNTs光阳极的DSSC最高光电转换效率能达到7.30%,比未处理的DSSC(5.38%)提高35.69%.     

Improvement of dye-sensitized solar cell performance through electrodepositing a close-packed TiO2 film

A simple electrodepositing method was proposed for fabricating a uniform, tight, and close-packed TiO₂ nanocrystalline film on the ITO substrate. The electrode and dye-sensitized solar cell (DSSC) with electrodeposited TiO₂ layer were characterized by scanning electron microscopy, cyclic voltammetry, and electrochemical impedance spectroscopy. The phthalocyanin dye, zinc tetra-carboxyl phthalocyanin complex, was used as a model dye to evaluate the influence of close-packed TiO₂ blocking layer on the photocurrent–voltage property. On the electrodeposition, the close-packed TiO₂ layer could effectively inhibit the recombination of charges, and therefore improve the performances of the corresponding cells. The effects of film thickness on light transmittance and photocurrent density of the corresponding cell were also demonstrated. The optimum film thickness was found to be approximately 400 nm. At the optimum thickness, the photocurrent density greatly increased comparing with that of the screen printing TiO₂ film. These results imply that our proposition was a potential and feasible method for the fabrication of DSSC practically.     

Fabrication of highly efficient dye-sensitized solar cell and CO2 reduction photocatalyst using TiO2 nanoparticles prepared by spin coating-assisted sol–gel method

A sol?Cgel method was applied for fabrication of nanocrystalline anatase TiO₂ thin films on ITO glass substrates and followed by rapid thermal annealing for application as the work electrode for dye-sensitized solar cells (DSSC). TiO₂ nanoparticles were characterized by X-ray diffraction (XRD) pattern and scanning electron microscopy (SEM) and the absorption of dye on the TiO₂ electrode was shown by UV?Cvis spectroscopy. By controlling different parameters including numbers of coated layers, the gap between two electrodes, sensitization time, and light source power, TiO₂-based solar cells with high efficiency was achieved. The results show that a five time spin-coated TiO₂ electrode with applying sealant and sensitization time of 24?h in N3 dye under illumination of 100?W?cm^?2 tungsten lamp give the optimum power conversion efficiency (??) of 6.61%. The increases in thickness of TiO₂ films by increasing the numbers of coated layers can improve adsorption of the N3 dye through TiO₂ layers to increase the open-circuit voltage (V _oc). However, short-circuit photocurrents (J _sc) of DSSCs with a one-coated layer of TiO₂ films are smaller than those of DSSCs with five-coated layer of TiO₂ films. It could be due to the fact that the increased thickness of TiO₂ thin films also resulted in a decrease in the transmittance of TiO₂ thin films. Also, this electrode was employed to photoreduce CO₂ with H₂O under tungsten lamp as light source.     

SrTiO3/TiO2 Hybridstructure as Photoanode in Dye‐Sensitized Solar Cell

In dye‐sensitized solar cells (DSSCs), the charge recombination at the TiO₂/dye/electrolyte interface greatly influences the photoelectron conversion efficiency. Hybrid semiconductor materials with matched band potentials are designed to reduce the charge recombination. In this study, SrTiO₃/TiO₂ hybridstructure was synthesized by using TiO₂ nanoparticles as template in a hydrothermal, showing a negative shift in the flat band potential. The DSSC with the SrTiO₃/TiO₂ anode exhibits an increased photovoltage and a reduced photocurrent. The suppression of charge recombination at the TiO₂/dye/electrolyte interface was observed in the electrochemical impedance spectroscopy, causing an improvement in the photovoltage. However, the SrTiO₃/TiO₂ system shows an obstructed electrons injection from the dye to SrTiO₃/TiO₂, limiting the photocurrent performance. The photoelectrochemical properties of the SrTiO₃/TiO₂ system are discussed in detail herein.     

表面活性剂对染料敏化太阳能电池光电性能的提高

在硝酸/醋酸(HNO₃/HAc)的水溶液中分别加入十二烷基苯磺酸钠(DBS)、十六烷基三甲基溴化铵(CTAB)、吐温20等不同类型的表面活性剂来水解钛酸四正丁酯制得前驱体溶液,通过水热法制备纳晶TiO₂,并组装成染料敏化太阳能电池(DSSC)。通过XRD、SEM和UV-Vis对纳晶TiO₂薄膜进行表征,并对DSSC进行光电流-光电压(I-V)曲线的测试,研究了不同类型的表面活性剂和不同浓度的CTAB对DSSC光电性能的影响。结果表明：加入阳离子表面活性剂CTAB时提高了DSSC的光电性能,而加入阴离子表面活性剂DBS和非离子表面活性剂吐温20时,DSSC的光电性能反而降低。随着CTAB浓度的增加,电池的光电性能先提高后下降,当c_CTAB=0.08 mol·L^-1时,DSSC的光电转化效率最高为5.76%,比不添加表面活性剂制备的纳晶TiO₂所组装的DSSC的光电转化效率提高了约18%。     

The preparation and characterization of nanostructured TiO2-ZrO2 mixed oxide electrode for efficient dye-sensitized solar cells

The preparation of nanostructured mixed metal oxide based on a sol-gel method with surfactant-assisted mechanism, and its application for dye-sensitized solar cell (DSSC) are reported. The mixed zirconia (ZrO₂) and titania (TiO₂) mesoporous powder possessed larger surface area than the corresponding titania. For the UV action spectra of unsensitized photochemical cell, the mixed zirconia/titania electrode can absorb UV light below 380 nm, corresponding to band gap (E_g) around 3.27 eV, which is higher than that of pure component of titania (). Both of these improved properties, i.e., BET surface area and band gap, contributed to the improvement on a short-circuit photocurrent up to 11%, an open-circuit voltage up to 4%, and a solar energy conversion efficiency up to 17%, for the DSSC fabricated by mesoporous zirconia/titania mixed system when compared to the cell that was fabricated only by nanostructured TiO₂. The cell fabricated by 5 μm thick mixed TiO₂-ZrO₂ electrode gave the short-circuit photocurrent about 13 mA/cm², open-circuit voltage about 600 mV and the conversion efficiency 5.4%.     

Effects of water-based gel electrolyte on the charge recombination and performance of dye-sensitized solar cells

A new water-based solution of ion-conductive polymeric gel electrolyte composed of polyethylene glycol and polyvinylpyrrolidone as gel-forming substances, I^?/I₃ ^? as reversible redox couple, and various ratios of acetonitrile/water solvents was prepared and used in the fabrication of dye-sensitized solar cells. The effects of water on the electrochemical behavior of the prepared electrolyte solutions were examined by the cyclic voltammetry and electrochemical impedance spectroscopy techniques. Electrochemical impedance spectroscopy was employed to quantify the charge-transfer resistance and the electron lifetime at the TiO₂ conduction band. The characteristic peak shifted to a lower frequency in the Bode phase plot, which is an indication of a longer electron lifetime for the cell containing more water content. Photovoltaic performance of the cells prepared by the new water-based gel electrolyte was studied. Changes in the current density–voltage (J–V) characteristics can be explained based on the effect of water on the energetics and kinetics of charge transport and charge recombination in the dye-sensitized solar cells (DSSCs). It was observed that the increase in open-circuit voltage (V _oc) and fill factor and decrease in J _SC were noticeable for cells containing water-based gel electrolyte. It was indicated that the charge recombination between injected electrons and electron acceptors (polyiodide) in the redox electrolyte was remarkably inhibited by the increase of water. The photovoltaic performance stability of the DSSC containing gel electrolyte solution including 50 wt% of water was examined, and it was shown that it is more stable than conventional cells considerably for 168 h. Energy conversion efficiency of 2.30 % was achieved, under illumination with a simulated solar light of 100 mW cm^?2.     

Enhanced photovoltaic characterization and charge transport of TIO2 nanoparticles/nanotubes composite photoanode based on indigo carmine dye-sensitized solar cells

Dye-sensitized solar cells (DSSCs) have established themselves as an alternative to conventional solar cells owing to their remarkably high power conversion efficiency, longtime stability and low-cost production. DSSCs composed of a dyed oxide semiconductor photoanode, a redox electrolyte and a counter electrode. In these devices, conversion efficiency is achieved by ultra-fast injection of an electron from a photo excited dye into the conduction band of metal oxide followed by subsequent dye regeneration and holes transportation to the counter electrode. The energy conversion efficiency of DSSC is to be dependent on the morphology and structure of the dye adsorbed metal oxide photoanode. Worldwide considerable efforts of DSSCs have been invested in morphology control of photoanode film, synthesis of stable optical sensitizers and improved ionic conductivity electrolytes. In the present investigation, a new composite nano structured photoanodes were prepared using TiO₂ nano tubes (TNTs) with TiO₂ nano particles (TNPs). TNPs were synthesized by sol–gel method and TNTs were prepared through an alkali hydrothermal transformation. Working photoanodes were prepared using five pastes of TNTs concentrations of 0, 10, 50, 90, and 100 % with TNPs. The DSSCs were fabricated using Indigo carmine dye as photo sensitizer and PMII (1-propyl-3-methylimmidazolium iodide) ionic liquid as electrolyte. The counter electrode was prepared using Copper sulfide. The structure and morphology of TNPs and TNTs were characterized by X-ray diffraction and electron microscopes (TEM and SEM). The photocurrent efficiency is measured using a solar simulator (100 mW/cm²). The prepared composite TNTs/TNPs photoanode could significantly improve the efficiency of dye-sensitized solar cells owing to its synergic effects, i.e. effective dye adsorption mainly originated from TiO₂ nanoparticles and rapid electron transport in one-dimensional TiO₂ nanotubes. The results of the present investigation suggested that the DSSC based on 10 % TNTs/TNPs showed better photovoltaic performance than cell made pure TiO₂ nanoparticles. The highest energy-conversion efficiency of 2.80 % is achieved by composite TNTs (10 %)/TNPs film, which is 68 % higher than that pure TNPs film and far larger than that formed by bare TNTs film (94 %). The charge transport and charge recombination behaviors of DSSCs were investigated by electrochemical impedance spectra and the results showed that composite TNTs/TNPs film-based cell possessed the lowest transfer resistances and the longest electron lifetime. Hence, it could be concluded that the composite TNTs/TNPs photoanodes facilitate the charge transport and enhancing the efficiencies of DSSCs.     

Investigation of the stability of solid-state dye-sensitized solar cells

The stability of the TiO₂/ruthenium dye/CuI solid-state solar cell was investigated under continuous simulated sunlight illumination. The cells showed fast degradation under full-spectrum sunlight illumination, but showed rather good stability when the ultraviolet part of the illumination was removed. XPS measurements showed evidence that TiO₂ could oxidize CuI in the presence of UV light. The photo-degradation mechanism of the cells is thus discussed on the basis of the photo-oxidative function of TiO₂. The long-term stability of the solid-state dye-sensitized solar cell (DSSC) was found to be improved under simulated sunlight by coating the TiO₂ porous electrode with an ultra-thin MgO layer, which was able to block the photo-oxidative activity of the TiO₂.     

Ionic liquid crystal-based electrolyte with enhanced charge transport for dye-sensitized solar cells

A room temperature ionic liquid crystal,1-dodecyl-3-ethylimidazolium iodide(C12EImI),and an ionic liquid,1-decyl-3-ethylimidazolium iodide(C10EImI),have been synthesized,characterized and employed as the electrolyte for dye-sensitized solar cells(DSSC).The physicochemical properties show that a smectic A(SmA)phase with a lamellar structure is formed in C12EImI.Both C12EImI and C10EImI have good electrochemical and thermal stability facilitating their use in DSSC.The steady-state voltammograms reveal that the diffusion coefficient of I3–in C12EImI is larger than that in C10EImI,which is attributed to the existence of the SmA phase in C12EImI.Because the iodide species are located between the layers of imidazolium cations in C12EImI,exchange reaction-based diffusion is increased with a consequent increase in,the overall diffusion.The electrochemical impedance spectrum reveals that charge recombination at the dyed TiO2/electrolyte interface of a C12EImI-based DSSC is reduced due to the increase in I3–diffusion,resulting in higher open-circuit voltage.Moreover,both short-circuit current density and fill factor of the C12EImI based DSSC increase,as a result of the increasing transport of I3–in C12EImI.Consequently,the photoelectric conversion efficiency of C12EImI-based DSSC is higher than that of the C10EImI–based DSSC.     

长链双烷基次膦酸作为共吸附剂修饰TiO_2光阳极

对TiO2/染料/电解质界面进行修饰是提高染料敏化太阳电池(DSC)性能的有效手段,其中引入共吸附剂有机小分子和染料共同吸附在TiO2表面是一种简单有效提高DSC性能的方法.本文合成了长链的双正十二烷基次膦酸(DDdPA)作为染料的共吸附剂应用于染料敏化太阳电池.通过红外光谱(FT-IR)表征DDdPA在TiO2表面的吸附;借助电化学阻抗谱(EIS)及强度调制光电流谱(IMPS)/强度调制光电压谱(IMVS)等技术表征了电子的传输与复合动力学过程.研究发现,DDdPA可以很好地与染料共同吸附在TiO2表面;与二(3,3-二甲基丁基)次膦酸(DINHOP)相比,DDdPA的引入可以更好地抑制TiO2/染料/电解质界面处的电子复合;在优化浓度配比下,DDdPA的引入有效提高了器件的电子寿命,使TiO2导带边负移约30 mV,最终使器件的开路电压提高了47 mV,光电转换效率提升约10%.     

Performance of CeO2–TiO2-admixed photoelectrode for natural dye-sensitized solar cell

Extracts from roots of Beta vulgaris were used as natural sensitizers of a wide-bandgap semiconductor (CeO₂–TiO₂) in photoelectrochemical solar cells. The natural dye, adsorbed onto the semiconductor surface, absorbs visible light and promotes electron transfer across the dye/semiconductor interface. We have applied CeO₂–TiO₂ to natural dye sensitizer solar cells as a photoelectrode to reduce the charge recombination rate by providing energy barrier at the interface between the photoanode and electrolyte which offers an improvement of photovoltaic efficiency. Short-circuit current density (J _sc) and open-circuit voltages (V _oc) of 9.0 mA cm^?2 and 680 mV, respectively, were obtained, and an effective energy conversion efficiency of 3.5?% was achieved. This simple and cheap technique of cell preparation opens up a perspective of commercial feasibility for inexpensive and environment-friendly dye cells.