Instantaneous flow field above the free end of finite-height cylinders and prisms

The flow above the free ends of surface-mounted finite-height circular cylinders and square prisms was studied experimentally using particle image velocimetry (PIV). Cylinders and prisms with aspect ratios of AR = 9, 7, 5, and 3 were tested at a Reynolds number of Re = 4.2 × 10⁴. The bodies were mounted normal to a ground plane and were partially immersed in a turbulent zero-pressure-gradient boundary layer, where the boundary layer thickness relative to the body width was δ/D = 1.6. PIV measurements were made above the free ends of the bodies in a vertical plane aligned with the flow centreline. The present PIV results provide insight into the effects of aspect ratio and body shape on the instantaneous flow field. The recirculation zone under the separated shear layer is larger for the square prism of AR = 3 compared to the more slender prism of AR = 9. Also, for a square prism with low aspect ratio (AR = 3), the influence of the reverse flow over the free end surface becomes more significant compared to that for a higher aspect ratio (AR = 9). For the circular cylinder, a cross-stream vortex forms within the recirculation zone. As the aspect ratio of the cylinder decreases, the reattachment point of the separated flow on the free end surface moves closer to the trailing edge. For both the square prism and circular cylinder cases, the instantaneous velocity vector field and associated in-plane vorticity field revealed small-scale structures mostly generated by the separated shear layer.     

The effect of incidence angle on the mean wake of surface-mounted finite-height square prisms

The mean wake of a surface-mounted finite-height square prism was studied experimentally in a low-speed wind tunnel to explore the combined effects of incidence angle (α) and aspect ratio (AR). Measurements of the mean wake velocity field were made with a seven-hole pressure probe for finite square prisms of AR = 9, 7, 5 and 3, at a Reynolds number of Re = 3.7 × 10⁴, for incidence angles from α = 0° to 45°. The relative thickness of the boundary layer on the ground plane, compared to the prism width, was δ/D = 1.5. As the incidence angle increases from α = 0° to 15°, the mean recirculation zone shortens and the mean wake shifts in the direction opposite to that of the mean lift force. The downwash is also deflected to this side of the wake and the mean streamwise vortex structures in the upper part of the wake become strongly asymmetric. The shortest mean recirculation zone, and the greatest asymmetry in the mean wake, is found at the critical incidence angle of α_critical ≈ 15°. As the incidence angle increases from α = 15° to 45°, the mean recirculation zone lengthens and the mean streamwise vortex structures regain their symmetry. These vortices also elongate in the wall-normal direction and become contiguous with the horseshoe vortex trailing arms. The mean wake of the prism of AR = 3 has some differences, such as an absence of induced streamwise vorticity near the ground plane, which support its classification as lying below the critical aspect ratio for the present flow conditions.     

Influence of aspect ratio on the mean flow field of a surface-mounted finite-height square prism

The flow around surface-mounted, finite-height square prisms at a Reynolds number of Re = 4.2 × 10⁴ was investigated experimentally in a low-speed wind tunnel using particle image velocimetry. The thickness of the boundary layer on the ground plane relative to the width of the prism was δ/D = 1.5. Four prism aspect ratios were tested, AR = 9, 7, 5, and 3, to study how the aspect ratio influences the flow field close to the prism. Upstream of the prism, lowering the aspect ratio from AR = 9 to AR = 3 causes the stagnation point on the upstream face to move closer to the free end, but there is no influence on the location and strength of the horseshoe vortex. Lowering the aspect ratio from AR = 9 to AR = 3 causes the cross-stream vortices in the upper and lower halves of the wake to move downstream and upstream, respectively; the latter vortex is absent for AR = 3, suggesting this prism sits below the critical aspect ratio. Above the free end of the prism, within the region of separated flow, lowering the aspect ratio from AR = 9 to AR = 3 shifts the location of the cross-stream vortex farther downstream. For the prism of AR = 3, reverse flow above the free end is stronger yet more unsteady compared to the more slender prisms, while the streamwise edge vortices are smaller and weaker.     

A numerical study of steady and unsteady viscoelastic flow past bounded cylinders

We consider two-dimensional, inertia-free, flow of a constant-viscosity viscoelastic fluid obeying the FENE-CR equation past a cylinder placed symmetrically in a channel, with a blockage ratio of 0.5. Through numerical simulations we show that the flow becomes unsteady when the Deborah number (using the usual definition) is greater than De ≈ 1.3, for an extensibility parameter of the model of L² = 144. The transition from steady to unsteady flow is characterised by a small pulsating recirculation zone of size approximately equal to 0.15 cylinder radius attached to the downstream face of the cylinder. There is also a rise in drag coefficient, which shows a sinusoidal variation with time. The results suggest a possible triggering mechanism leading to the steady three-dimensional Gortler-type vortical structures, which have been observed in experiments of the flow of a viscoelastic fluid around cylinders. The results reveal that the reason for failure of the search for steady numerical solutions at relatively high Deborah numbers is that the two-dimensional flow separates and eventually becomes unsteady. For a lower extensibility parameter, L² = 100, a similar recirculation is formed given rise to a small standing eddy behind the cylinder which becomes unsteady and pulsates in time for Deborah numbers larger than De ≈ 4.0–4.5.     

Characteristics of the free-end mean pressure distribution for a surface-mounted finite-height cylinder

Wind tunnel experiments at a Reynolds number of Re = 6.5 × 10⁴ were used to study the effect of aspect ratio and boundary layer thickness on the mean static pressure distribution on the free end of a surface-mounted finite-height cylinder. The cylinder's aspect ratio was changed in small increments from AR = 0.5 to AR = 11. Two different boundary layer thicknesses (relative to the cylinder diameter) were employed, δ/D = 0.6 and δ/D = 1.9. From analysis of the mean pressure contour plots, it was found that the sizes and locations of regions of lower pressure, adverse pressure gradient, and higher pressure, and the appearance of “eye-like spots”, are sensitive to both AR and δ/D. The adverse pressure gradient occurs just ahead of the mean reattachment line while the eye-like spots are related to termination points of the legs of the arch vortex within the free-end mean recirculation zone. The total normal force coefficient experienced by the cylinder is strongly influenced by the contribution of the wall shear stress on the sides of the cylinder, with a change in direction of the net vertical shear stress contribution occurring between AR = 7 and AR = 8 for both boundary layers.     

Flow above the free end of a surface-mounted finite-height circular cylinder: A review

The wake of a surface-mounted finite-height circular cylinder and the associated vortex patterns are strongly dependent on the cylinder aspect ratio and the thickness of the boundary layer on the ground plane relative to the dimensions of the cylinder. Above a critical aspect ratio, the mean wake is characterized by streamwise tip vortex structures and Kármán vortex shedding from the sides of the cylinder. Below a critical aspect ratio, a unique mean wake structure is observed. Recent experimental studies in the literature that used phase-averaged techniques, as well as recent numerical simulations, have led to an improved physical understanding of the near-wake vortex flow patterns. However, the flow above the free end of the finite circular cylinder, and its relationship to the near wake, has not been systematically studied. The effects of aspect ratio and boundary layer thickness on the free-end flow field are also not completely understood, nor has the influence of Reynolds number on the free-end flow field been fully explored. Common features associated with the free end include separation from the leading edge, a mean recirculation zone containing a prominent cross-stream arch (or mushroom) vortex, and reattachment onto the free-surface. Other flow features that remain to be clarified include a separation bubble near the leading edge, one or two cross-stream vortices within this separation bubble, the origins of the streamwise tip or trailing vortices, and various critical points in the near-surface flow topology. This paper reviews the current understanding of the flow above the free end of a surface-mounted finite-height circular cylinder, with a focus on models of the flow field, surface oil flow visualization studies, pressure and heat flux distributions on the free-end surface, measurements of the local velocity field, and numerical simulations, found in the literature.     

Separated flow structures around a cylindrical obstacle in a narrow channel

A detailed experimental study is performed on the separated flow structures around a low aspect-ratio circular cylinder (pin-fin) in a practical configuration of liquid cooling channel. Distinctive features of the present arrangement are the confinement of the cylinder at both ends, water flow at low Reynolds numbers (Re = 800, 1800, 2800), very high core flow turbulence and undeveloped boundary layers at the position of the obstacle. The horseshoe vortex system at the junctions between the cylinder and the confining walls and the near wake region behind the obstacle are deeply investigated by means of Particle Image Velocimetry (PIV). Upstream of the cylinder, the horseshoe vortex system turns out to be perturbed by vorticity bursts from the incoming boundary layers, leading to aperiodical vortex oscillations at Re = 800 or to break-away and secondary vorticity eruptions at the higher Reynolds numbers. The flow structures in the near wake show a complex three-dimensional behaviour associated with a peculiar mechanism of spanwise mass transport. High levels of free-stream turbulence trigger an early instabilization of the shear layers and strong Bloor–Gerrard vortices are observed even at Re = 800. Coalescence of these vortices and intense spanwise flow inhibit the alternate primary vortex shedding for time periods whose length and frequency increase as the Reynolds number is reduced. The inhibition of alternate vortex shedding for long time periods is finally related to the very large wake characteristic lengths and to the low velocity fluctuations observed especially at the lowest Reynolds number.     

Influence of single rectangular groove on the flow past a circular cylinder

In the present study, flow control mechanism of single groove on a circular cylinder surface is presented experimentally using Particle image velocimetry (PIV). A square shaped groove is patterned longitudinally on the surface of the cylinder with a diameter of 50 mm. The flow characteristics are studied as a function of angular position of the groove from the forward stagnation point of the cylinder within 0° ≤ θ ≤ 150°. In the current work, instantaneous and time-averaged flow data such as vorticity, ω streamline, Ψ streamwise, u/U_o and transverse, v/U_o velocity components, turbulent kinetic energy, TKE and RMS of streamwise, u_rms and transverse, v_rms velocity components are utilized in order to present the results of quantitative analyses. Furthermore, Strouhal numbers are calculated using Karman vortex shedding frequency, f_k obtained from single point spectral analysis. It is concluded that a critical angular position of the groove, θ = 80° is observed. The flow separation is controlled within 0° ≤ θ < 80°. At θ = 80°, the flow separation starts to occur in the upstream direction. The instability within the shear layer is also induced on grooved side of the cylinder with frequencies different than Karman vortex shedding frequency, f_k.     

Coherent vortical and straining structures in the finite wall-mounted square cylinder wake

Topological aspects of the turbulent wake of a finite, surface-mounted, square-cross-section cylinder of h/d = 4 are addressed by decomposing the velocity field into a quasi-periodic coherent part and the unresolved incoherent fluctuations. The three-dimensional large scale structure is educed through a reconstruction of planar phase-averaged PIV measurements using the simultaneously sampled surface pressure difference on opposing sides of the obstacle as a phase reference. A topological model for the vortex structure is educed and mean streamwise wake vorticity is explained in terms of the connections between initially vertical structures shed alternately from either side of the obstacle, rather than previously proposed ‘tip’ vortex structures generated at the obstacle free-end. The coherent structure educed accounts for a significant portion of the fluctuating energy in the wake. The turbulent field is further analyzed by finding Lagrangian straining structures that form by induction of the coherent vorticity field, and these structures are related to the energy transfer from the base phase-averaged flow since they act to stretch incoherent vorticity fluctuations in their neighbourhood.     

Thermal study of an array of inline horizontal cylinders below a nearly adiabatic ceiling

Steady state two-dimensional free convection heat transfer from a horizontal, isothermal cylinder in a horizontal array of cylinders consists of three isothermal cylinders, located underneath a nearly adiabatic ceiling is studied experimentally. A Mach–Zehnder interferometer is used to determine thermal field and smoke test is made to visualize flow field. Effects of the cylinders spacing to its diameter (S/D), and cylinder distance from ceiling to its diameter (L/D) on heat transfer from the centered cylinder are investigated for Rayleigh numbers from 1500 to 6000. Experiments are performed for an inline array configuration of horizontal cylinders of diameters D = 13 mm. Results indicate that due to the nearly adiabatic ceiling and neighboring cylinders, thermal plume resulted from the centered cylinder separates from cylinder surface even for high L/D values and forming recirculation regions. By decreasing the space ratio S/D, the recirculation flow strength increases. Also, by decreasing S/D, boundary layers of neighboring cylinders combine and form a developing flow between cylinders. The strength of developing flow depends on the cylinders Rayleigh number and S/D ratio. Due to the developing flow between cylinders, the vortex flow on the top of the centered cylinder appears for all L/D ratios and this vortex influences the value of local Nusselt number distribution around the cylinder.Variation of average Nusselt number of the centered cylinder depends highly on L/D and the trend with S/D depends on the value of Rayleigh number.     

Low Reynolds number flow over a square cylinder with a detached flat plate

A numerical study of the alteration of a square cylinder wake using a detached downstream thin flat plate is presented. The wake is generated by a uniform flow of Reynolds number 150 based on the side length of the cylinder, D. The sensitivity of the near wake structure to the downstream position of the plate is investigated by varying the gap distance (G) along the wake centerline in the range 0 ⩽ G ⩽ 7D for a constant plate length of L = D. A critical gap distance is observed to occur at G_c ≈ 2.3D that indicates the existence of two flow regimes. Regime I is characterised by vortex formation occurring downstream of the gap while for regime II, formation occurs within the gap. By varying the plate length and gap distance, a condition is found where significant unsteady total lift reduction can occur. The root mean square lift reduction is limited by an unsteady stall process on the plate.     

Effect of side ratio on fluid flow and heat transfer from rectangular cylinders using the PANS method

A computational study of heat transfer from rectangular cylinders is carried out. Rectangular cylinders are distinguished based on the ratio of the length of streamwise face to the height of the cross-stream face (side ratio, R). The simulations were performed to understand the heat transfer in a flow field comprising separation, reattachment, vortex shedding and stagnation. The Partially-Averaged Navier–Stokes (PANS) modeling approach is used to solve the turbulent flow physics associated and the wall resolve approach is used for the near wall treatment because of the flow separation involved. The simulations were performed using a finite volume based opensource software, OpenFOAM, at Reynolds number (Re) = 22,000 for rectangular cylinder at constant temperature kept in an air stream. Two critical side ratios were obtained, R = 0.62 and 3.0. At R = 0.62, the maximum value of the drag coefficient (C_d) = 2.681 was observed which gradually reduced by 54% at R = 4.0. The base pressure coefficient and global Nusselt number also attained the maximum value at R = 0.62 and from R = 2.5 to 3.0 a sharp discontinuous increase by 140% in the Strouhal number was observed. At R = 0.62, it was observed that the separated flow reattaches at the trailing edge after rolling over the side face and therefore increases the overall Nusselt number. The phase averaging was also performed to analyze the unsteady behavior of heat transfer.     

Influence of wall proximity on characteristics of wake behind a square cylinder: PIV measurements and POD analysis

Influence of wall proximity on characteristics of the wake behind a two-dimensional square cylinder was experimentally studied in the present work. A low-speed recirculation water channel was established for the experiment; the Reynolds number based on the free-stream velocity and cylinder width (D) was kept at Re_D = 2250. Four cases with different gap width, e.g., G/D = 0.1, 0.2, 0.4 and 0.8, were chosen for comparison. Two experimental techniques, e.g., the standard PIV with high image-density CCD camera and TR-PIV with a high-speed camera were employed in measuring the wake field, enabling a comprehensive view of the time-averaged wake pattern at high spatial resolution and the instantaneous flow field at high temporal resolution, respectively. For the four cases, the difference in spatial characteristics of the wake in the vicinity of the plane wall was analyzed in terms of the time-averaged quantities measured by the standard PIV, e.g., the streamline pattern, the vector field, the streamwise velocity fluctuation intensity and the reverse-flow intermittency. The proper orthogonal decomposition (POD) method was extensively used to decompose the TR-PIV measurements, giving a close-up view of the energetic POD modes buried in the wake. The low-order flow model of the wake at G/D = 0.8 and 0.4 was constructed by using the linear combination of the first two POD modes and the time-mean flow field, which reflected well the vortex shedding process in the sense of the phase-dependent patterns. The intermittent appearance of the weakly separated region near the wall was found at G/D = 0.4. On going from G/D = 0.8 to 0.4, the remarkable variation of the instantaneous wake in the longitudinal direction confirmed that the wall constraint stretches the vortices in the plane of the wall and transfers the energy to the longitudinal component at the expense of the lateral one.     

Transient phenomena in separation control over a NACA 0015 airfoil

We present the transient phenomena occurring during the impulsive control of flow separation over a NACA0015 airfoil at an incidence angle of 11° and a chord Reynolds number of 1 million. Actuation is performed via pneumatic vortex generators, impulsively activated in order to analyze the transient phenomena corresponding to the attachment process and, conversely, to transient re-separation occurring when the actuators are switched off. Measurements are performed using a linear array of unsteady pressure transducers and a single traversing crosswire. The pressure transducers are positioned in the separated region of the airfoil, which extends ∼ 0.3c upstream of the trailing edge at the above flow condition. To control the flow, the angled fluidic vortex generators are positioned in a single spanwise array located 0.3c downstream of the leading edge of the airfoil. We establish a statistical relationship between pressure and velocity signals during both the uncontrolled steady state and the transient processes of attachment and separation. The unsteady behavior of the attachment process is also qualitatively analyzed via a 0.3 million Reynold number visualizations. The emission of a “starting vortex” is evidenced. This corresponds to a transient increase of drag.     

Influence of rounding corners on the wake of a finite-length cylinder: An experimental study

This study aims to investigate experimentally the influence of rounding corners (r) as well as aspect ratio (AR) on the flow structures of a surface-mounted finite cylinder. The cylinders with sharp (r* = r/D = 0) and rounded corners (r*=0.167, 0.25 and 0.5) and aspect ratio or height-to-width/diameter ratio (AR = H/D) between 2 and 7 are utilized. The experiments are based on the five-hole probe and hot-wire measurements as well as the oil flow visualization. Wake measurements are made in an open return wind tunnel at the Reynolds number, Re = 1.6 × 10⁴, where Re is defined based on the side width/diameter (D) of the cylinder cross-section and the freestream velocity. It is found that r* and AR have significant effects on the flow structure from the perspective of wake topology, strength of streamwise vortices, and vortex shedding frequency. For all r* considered, the wake is characterized by a quadrupole type (both the tip and base vortices are present) at AR = 7, while a dipole type occurs for AR = 2 and 4 (the base vortices are absent). The strength (circulation) of the streamwise vortex structures is affected by r*. For all AR examined in the present study, the strengths of tip and base vortex structures decrease with increasing r*. The oil flow visualization demonstrates that the features of the horseshoe vortex are sensitive to r* and AR. With increasing r*, the location of the separation line moves downstream and the distance between horseshoe vortex legs decreases. Velocity measurements reveal that the downwash flow enhances with increasing r*. It is also found that the Strouhal number increases progressively by 60% as r* increases from 0 to 0.5, regardless of AR.     

Flow pattern and molecular visualization of DNA solutions through a 4:1 planar micro-contraction

The present work explores unusual flow behavior of entangled fluids in an abrupt contraction flow device. Fluorescent imaging was carried out on four different entangled DNA solutions with concentrations ranging from 0.1 to 1.0% (with a wide range of entanglements per chain Z = 7–55). For weakly entangled solutions (Z < 30), vortex flow was dominant at high flow rates. However, for well-entangled DNA solutions (Z ≥ 30), unusual time dependant shear banding was observed at the contraction entrance. Upon reducing the slip length by adding sucrose to the well-entangled DNA solution, vortex flow became dominant again. In vortex flow, most DNA chains remained coiled at the corner in regular recirculation. However, when jerky-shear-banding flow developed, significant stable stretching of DNA chains occurred at the center-line, with quasi-periodic switching between stretching and recoil at the corner.     

Criteria for the appearance of recirculating and non-stationary regimes behind a cylinder in a viscoplastic fluid

The appearance of a recirculation zone and the formation of non-stationary vortices behind a cylinder in the unconfined flow of a Herschel–Bulkley fluid have been studied by numerical simulation. The Herschel–Bulkley constitutive equation was regularised by using the Papanastasiou model. Special attention was paid to determining the numerical parameters and comparing them to existing results. The influence of the Oldroyd number and power-law index on flow morphology and, in particular, on the unyielded zones was studied over a wide spectrum (0 ≤ Od ≤ 10) and (0.3 ≤ n ≤ 1.8). It was seen that the greater the Oldroyd number, the greater the critical Reynolds numbers and Strouhal number for the two flow regimes. The influence of the power-law index is more complex.     

An active flow control strategy for the suppression of vortex structures behind a circular cylinder

An algorithm is proposed to model, predict and control vortex shedding behind a circular cylindrical configuration. The main ingredients of the algorithm include multiple-feedback sensors, actuators (with zero net mass injection) and a control strategy. Along with the mass and momentum conservation equations, a control equation is implemented to enable the desired flow control goals. A number of sensors are chosen in the downstream of the body to report the state of the flow. The role of externally controllable actuators on the fluid flow patterns past a circular configuration is assessed. To enable, zero net mass injection, two simple rotary type mechanical actuators are located at 120°, right behind the main cylinder. The popular finite volume based SIMPLE scheme is employed for the numerical calculations. As a precursor, the scheme simulates flow past an isolated cylinder, which is validated over a moderate range of Reynolds numbers. The design parameters of interest such as Strouhal number, drag and lift coefficients etc are used for the purpose of validation. The simulated flow fields are compared against the flow visualization study, which clearly demonstrates the efficacy of the actuators at discrete levels of rotation. The basic character of the flow is completely modified at U_c/U_∞ = 2.0 and Re = 100, where a complete suppression of vortex shedding is observed. This is tantamount to complete control of all the global instability modes. Fictitious tracer particles are released to visualize the vortex structures in the form of streaklines. The results clearly demonstrate the effectiveness of a rather simple active control algorithm in suppressing the vortex structures. All the relevant fluid flow features of the bluff-body fluid mechanics under the influence of actuators are studied in the sub-critical Reynolds number range of Re = 100–300.     

The effect of corona discharge on free convection heat transfer from a horizontal cylinder

Free convection heat transfer from an isothermal horizontal cylinder in the presence of DC positive corona discharge with a blade edge emitter electrode has been studied experimentally and numerically. A Mach–Zehnder interferometer was used to determine the local Nusselt numbers. The effect of corona discharge on heat transfer from the cylinder was investigated at Rayleigh numbers in the range between 1500 and 5000. To find the details of the flow patterns and to further verify the experimental results, numerical simulations were also performed. It was found that the numerical results are in good agreement with experimental data. By increasing the applied voltage up to 15.5 kV, the corona discharge generates a recirculation zone around the blade and below the lower stagnation point of the cylinder. The effect of the recirculation zone becomes stronger near the breakdown voltage (17 kV) and it is responsible for a local decrease in the cooling of the cylinder around the lower stagnation point. The results indicate that corona discharge has a significant effect on the average Nusselt number at lower Rayleigh numbers whereas it has smaller effect at higher Rayleigh numbers.     

Tip gap height effects on flow structure and heat/mass transfer over plane tip of a high-turning turbine rotor blade

The effects of tip gap height-to-chord ratio, h/c, on the flow structure and heat/mass transfer over the plane tip surface of a large-scale high-turning turbine rotor blade have been investigated for h/c = 1.0%, 2.0%, 3.0% and 4.0%. For near-wall tip gap flow visualizations, a high-resolution oil film method is employed, and the naphthalene sublimation technique is used for local heat/mass transfer rate measurements. From the tip surface visualizations, a pair of vortices named “tip gap vortices” is identified in the leading edge region within the tip gap. The overall tip gap flow is characterized not only by the tip gap vortices but also by the flow separation/re-attachment process along the pressure-side tip edge. Within the separation bubble, there exist complicated near-wall flows moving toward a mid-chord flow converging area. With increasing h/c, the tip gap vortices, the flow separation/re-attachment, and the converging flows within the separation bubble tend to be intensified. In general, higher thermal load is found along the loci of the tip gap vortices and along the re-attachment line, while lower thermal load is observed behind the tip gap vortex system and near the mid-chord flow converging area. Heat/mass transfer characteristics with the variation of h/c are discussed in detail in conjunction with the tip gap flow features. Based on the flow visualizations and heat/mass transfer data, new realistic tip gap flow models have been proposed for h/c = 1.0 and 4.0%.