双光路测量红外飞秒激光脉冲的载波包络相位稳定性

描述了利用双光路自参考技术测量红外飞秒脉冲载波包络相移的方法,并通过建立的红外飞秒脉冲载波包络相移测量装置,实验测量了自主搭建的可调谐光学参量放大系统输出的红外飞秒激光脉冲的载波包络相移.对于1.6 μm的激光脉冲,测量得到在100 s内其相位抖动为115 mrad（rms）.实验结果表明双光路法具有易于调节、测量方便、应用性强等优点. 关键词： 飞秒激光测量 自参考技术 双光路 载波包络相位     

基于多光子脉冲内干涉相位扫描法对飞秒激光脉冲进行相位测量和补偿的研究

研制了一套基于多光子脉冲内干涉相位扫描方法的可以同时对飞秒激光脉冲进行相位测量和补偿的实验系统装置.实验中,通过自主研发的LabVIEW程序控制液晶空间光调制器和光纤光谱仪,对待测飞秒激光脉冲施加相位扫描,并同时记录受到调制的飞秒激光脉冲的倍频光谱,得到了多光子脉冲内干涉相位扫描(MIIPS)轨迹图.通过MIIPS轨迹图的三次测量和迭代运算,还原出了经过预先啁啾调制的中心波长约为810 nm、重复频率为1 kHz的飞秒激光脉冲的光谱相位,测量精度在0.1 rad以内.根据测量结果,利用液晶空间光调制器对该飞秒激光脉冲进行相位补偿,得到了近似傅里叶变换极限的飞秒激光脉冲.这一装置将在多光子显微成像、脉冲整形、飞秒激光光谱学等众多领域发挥重要作用.     

用于激光二极管抽运固体激光器热畸变补偿的微变形镜特性研究

在很多高功率的激光器中,由于热效应的缘故会导致激光器的光束质量大幅下降。为了改善激光光束的动态畸变,自适应光学是一种有效的方法。作为自适应光学系统的核心部件,设计了一种可用于大功率激光二极管抽运固体激光器(DPL)热畸变补偿的新型可变形反射镜,并且通过工艺流片实际制造出有效反射面积为30 mm×30 mm,拥有49个静电驱动单元的可变形反射镜。对该微机电系统(MEMS)微变形镜的变形特性进行了详细的理论分析和模拟研究,并和实际测量结果进行了比较,得到了满意的结果。为了实现闭环控制,对微变形反射镜的光学影响函数矩阵进行了全面测量,并用得到的电压矩阵对畸变激光光束的波前进行了校正。实验结果表明,微变形反射镜可以有效地改善激光光束质量。     

激光光场的大行程相位锁定及控制系统

提出了一种实现大行程飞秒激光脉冲对相位控制的方法。其设计思想是:在迈克耳孙干涉仪中,利用改变激光偏振态的方法改变输出两光束的光程差因子。在对He-Ne激光输出的两束光实现相位锁定的基础上,进而提出了一种可对于超短激光双脉冲相对相位差实现超大行程控制的方法。对He-Ne激光的动态相位锁定、以及飞秒激光脉冲对的相对相位差控制分别作了实验验证。对He-Ne激光的静态相位锁定结果表明干涉仪两臂光程差可以控制在纳米精度;而飞秒激光脉冲测量自相关曲线与理论拟合结果非常接近,经傅里叶变换可得到较好的单峰谱图。该系统能够在实验范围中几乎无行程限制地实现飞秒激光脉冲对的相对相位动态稳定控制。     

基于随机并行梯度下降方法的动态光束净化实验研究

高能激光系统中通常包含光束净化装置以对激光器出射光束的波前畸变进行连续校正.为研究随机并行梯度下降自适应光学方法在光束净化问题上的可行性,按算法运行时序连续改变37单元变形镜的面形,以在实验光路中引入高能激光器输出光束的常见动态波前畸变,同时采用随机并行梯度下降算法控制同一变形镜对此动态畸变进行校正.实验结果显示,在事先消除系统初始像差的情况下,系统分别以1 kHz和2 kHz的模拟迭代速率工作时,激光束的动态像差都得到了充分抑制,光束质量在整个校正时段内始终维持在较好水平.这表明随机并行梯度下降自适应光学方法应用在光束净化系统中是可行的.     

内腔自适应光学系统校正激光器畸变

固体激光器中,增益介质由于热沉积产生的热畸变严重影响了激光器的稳定性、输出功率和光束质量。研究了一种内腔自适应光学系统校正激光器腔内畸变的方法,利用微机电变形反射镜作为固体激光器的内腔全反射镜,通过控制变形镜的面型改善激光器输出光束的模式及功率。从腔外引入的一束信标光通过激光器内腔后反射出腔外,用波前探测器可测得激光器工作时腔内畸变对此信标光的影响,并通过搭建的自适应光学系统平台可闭环校正此畸变。实验结果表明,闭环校正后,激光器的输出功率提高了近3倍,且激光光束质量得到了明显的改善。     

飞秒激光非线性频率转换的自适应优化过程

使用闭环控制的自适应控制光学系统对飞秒激光的波前进行调控,可以有效改善激光与物质相互作用中由于相位畸变或光路偏差导致的效率下降。利用可编程纯相位的液晶空间光调制器结合模拟退火算法设计的自适应优化系统,在BBO晶体的飞秒倍频过程中实现了对相位畸变和光路偏差导致倍频效率下降的自动补偿,从而实现飞秒倍频效率的最优化。     

不同波长飞秒脉冲的相位测量

飞秒脉冲技术的不断发展能够较方便地产生不同波段和结构特性的飞秒脉冲. 对已有的改进型零附加相位光谱相位相干电场重构系统进行优化整合,使之胜任不同特性飞秒脉冲的测量. 利用该系统测量了两台飞秒激光系统输出不同波长的脉冲及其通过厚度为80 mm的BK7玻璃块而得到的啁啾脉冲. 实验结果表明,该系统的适用范围较宽. 关键词： 光谱相位相干直接电场重构法 飞秒脉冲测量 波长     

基于时域剪切干涉的纳秒脉冲相位测量技术

提出一种时域剪切干涉技术测量纳秒激光脉冲的时间相位分布,该方法将待测脉冲分为彼此之间有数百个皮秒延迟量的两个脉冲;并在对其中一个脉冲加入适量的频移后和另一个脉冲合束,得到时域干涉条纹;最后采用相适应的算法,从记录的时域条纹计算得到纳秒激光脉冲的时间相位分布,并进一步计算得到激光脉冲的精细光谱结构.在对测量原理进行系统分析的基础上,利用数值模拟和实验对该相位测量技术的可行性进行了验证,并系统分析了其测量误差和非理想条件下的各种干扰因素的影响.由于该测量技术不采用任何非线光学方法,可对任何波长的激光脉冲进行测量,具有光路简单、测量精度高和适用范围广等优点,为需要对纳秒激光脉冲的时域相位分布进行测量的高功率激光等领域提供了一种简单便捷的测量新技术.     

超连续谱干涉方法测量古依相移

利用两束超连续光干涉得到的信号,测量了透镜焦点附近飞秒激光脉冲的古依(Gouy)相移。根据得到的光谱干涉信号,利用傅里叶变换得到相对相位值。激光光束在聚焦透镜后的束腰半径可以由成像方法测得。根据测量得到的激光光束束腰半径,用非线性拟合的方法得到了古依相移曲线,拟合曲线与实验结果符合得非常好。给出了古依相位在焦点前后1 mm区域内的移动量。     

Generation of high average power, 7.5-fs blue pulses at 5 kHz by adaptive phase control

The spectral width of a 5-kHz Ti:sapphire laser system was broadened by spectral control in a regenerative amplifier consisting of broadband chirped mirrors. The dispersion over the wide spectral range was compensated by a deformable mirror along with a genetic algorithm, resulting in a pulse width of 15 fs. The pulse width is the shortest, to our knowledge, in chirped pulse amplification systems with a regenerative amplifier. The phase distortion of broadband frequency doubling in addition to the Ti:sapphire laser was compensated by using the self-diffraction intensity in sapphire as the feedback signal into the genetic algorithm, resulting in a pulse width of 7.5 fs. The average power of the second harmonic was 1 W with a fundamental input of 7 W.     

腔内反射镜色散控制的、自启动的钛宝石飞秒脉冲激光器

报道了自行研制的色散补偿镜;并用此取代传统的腔内棱镜对,结合半导体可饱和吸收镜实现了腔内反射镜色散控制的,自启动的掺钛蓝宝石激光器的飞秒激光运转。     

Wavefront correction of Ti:sapphire terawatt laser with varying precision of phase conjugation between deformable mirror and wavefront sensor

The phase conjugation between the deformable mirror and the wavefront sensor in the aberration correction of a terawatt Ti:sapphire laser is studied experimentally and theoretically in this paper. At varying values of phase-conjugation precision, we focus the corresponding beams into spots of the same size of 5.1 μm×5.3 μm with a f/4 parabola in the 32 TW/36 fs Ti:sapphire laser system. The results show that the precision of conjugation can induce an intensity modulation but does not significantly affect the wavefront correction.     

飞秒紫外激光脉冲振荡的实验研究

本文讨论了采用空间光脉冲光谱的啁啾特性和选择聚焦透镜焦距相结合的技术大大提高二次谐波转换效率和产生紫外飞秒光脉冲的实验研究.采用一类相位匹配的BBO晶体,当飞秒钛宝石光脉冲平均功率为560mW时,二次谐波输出功率为352mW,二次谐波转换效率高达63%;采用一类相位匹配的LBO晶体时,获得高光束质量的倍频蓝光输出,输出平均功率为170mW,转换效率大于30%.运用LBO倍频产生的蓝光脉冲和剩余的基频光脉冲进行了三次谐波的振荡研究.三倍频晶体采用BBO,通过优化设计倍频光与基频光之间的空间模匹配及精确时间延迟,得到飞秒紫外光输出,输出功率为2mW,中心波长约为280nm,重复率为100MHz.     

Seven-terawatt Ti:sapphire laser system operating at 50 Hz with high beam quality for laser Compton femtosecond X-ray generation

We present a 7-TW Ti:sapphire laser system operating at 50 Hz for laser Compton femtosecond X-ray generation. This laser system delivers 8.4 W of average output power at a repetition rate of 50 Hz with a pulse width of 24 fs. It demonstrates successful management using a dynamically stable resonator in the regenerative amplifier and compensation for thermal lensing by a convex mirror in a ring-type four-pass power amplifier. We also present the results of closed-loop corrections for distorted wavefronts of amplified and compressed laser pulses, using an adaptive optical system consisting of a Shack–Hartmann-type wavefront sensor and a deformable mirror. This closed-loop correction results in dramatic improvements, reducing wavefront distortions below 0.05 λ rms. Received: 31 October 2002 / Revised version: 3 March 2003 / Published online: 5 May 2003 RID="*" ID="*"Corresponding author. Fax: +81-298/61-3349, E-mail: ito@festa.or.jp     

用SPIDER法测量飞秒激光脉冲的光谱相位

介绍了用SPIDER测量光谱相位的实验装置和模拟计算飞秒激光特性参数的原理；提出了Ω 和τ等重要参数的确定方法.实验上用自建的SPIDER进行了掺钛蓝宝石飞秒振荡器输出脉 冲的相位测量，并以此为基础还原出了原输入脉冲的时域形式，模合计算所得的脉宽为107 fs，与利用二次相关法直接测量的结果十分一致. 关键词： 飞秒激光 SPIDER 光谱相位 光谱相干     

Piezo-driven deformable mirror for femtosecond pulse shaping

We have developed a deformable, gold-coated mirror based on piezoelectric actuators with 15-micros response time. With 20 independent channels we were able to compress 72-fs pulses from a Ti:sapphire oscillator down to 45 fs in a 4f zero-dispersion compressor arrangement. Spectral interference was used to measure the mirror performance, while the spectral phase interferometry for direct electric field reconstruction (SPIDER) technique was used for the laser pulse characterization.     

1-mJ, sub-5-fs carrier–envelope phase-locked pulses

We report the routine generation of sub-5-fs laser pulses with 1-mJ energy and stable carrier–envelope phase at 1-kHz repetition rate, obtained by compressing the multi-mJ output from a phase-locked Ti:sapphire amplifier in a rare-gas-filled hollow fiber. The dual-stage amplifier features a hybrid transmission grating/chirped mirror compressor providing 2.2-mJ, 26-fs pulses at 1 kHz with standard phase deviation of 190 mrad rms. We demonstrate hour-long phase stability without feedback control of grating position or rigorous control of the laser environment, simply by using small pulse stretching factors in the amplifier, which minimize the beam pathway in the compressor. The amplifier also integrates a versatile AOPDF (acousto-optic programmable dispersive filter) for closed-loop spectral phase optimization. The various factors influencing the overall phase stability of the system are discussed in detail. Using the optimized output, 1-mJ, 4.5-fs pulses are generated by seeding the neon gas filled hollow fiber with a circularly polarized input beam. A standard phase deviation of 230 mrad after the HCF is obtained by direct f-to-2f detection and slow-loop feedback to the oscillator locking electronics without any additional spectral broadening.     

可编程声光色散滤波器在10 Hz飞秒再生放大系统中的应用

报道了在10 Hz飞秒再生放大超快激光系统中,运用可编程声光色散滤波器(AOPDF)对注入再生放大的种子光进行频谱整形和色散预补偿,使钛宝石激光系统输出光脉冲谱线半峰全宽由原来的38 nm展宽到66 nm,压缩后输出脉冲宽度从35 fs减小到20 fs。实验结果表明,利用可编程声光色散滤波器能够同时独立进行光谱整形和大范围内色散补偿的特性,可以有效抑制啁啾脉冲放大过程中存在的谱线增益窄化效应,补偿钛宝石激光系统中存在的残留色散。这为进一步研制小于20 fs,10 TW量级钛宝石激光系统奠定了基础。     

12-fs pulses from a continuous-wave-pumped 200-nJ Ti:sapphire amplifier at a variable repetition rate as high as 4 MHz

We demonstrate a novel compact femtosecond Ti:sapphire laser system operating at repetition rates from 10 kHz to 4 MHz. The scheme is based on the combination of a broadband cavity-dumped oscillator and a double-pass Ti:sapphire amplifier pumped by a low-noise cw solid-state laser. Amplified pulses with an extremely smooth spectrum, a duration of only 12 fs, and less than 0.25% rms fluctuation are generated in a beam with M2 < 1.2. A maximum pulse energy of 210 nJ and an average output power of as much as 720 mW are achieved. This output energy is sufficient to generate a stable continuum in a sapphire disk.