Functionalization of Single‐Walled Carbon Nanotubes with Cubic Prussian Blue and Its Application for Amperometric Sensing

In this work, we synthesized electroactive cubic Prussian blue (PB) modified single‐walled carbon nanotubes (SWNTs) nanocomposites using the mixture solution of ferric‐(III) chloride and potassium ferricyanide under ambient conditions. The successful fabrication of the PB‐SWNTs nanocomposites was confirmed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV‐vis absorption spectroscopy, Fourier transform infrared (FTIR) spectroscopy, and cyclic voltammetry (CV). PB nanocrystallites are observed to be finely attached on the SWNTs sidewalls in which the SWNTs not only act as a carrier of PB nanocrystallites but also as Fe(III)‐reducer. The electrochemical properties of PB‐SWNTs nanocomposites were also investigated. Using the electrodeposition technique, a thin film of PB‐SWNTs/chitosan nanocomposites was prepared onto glassy carbon electrode (GCE) for the construction of a H₂O₂ sensor. PB‐SWNTs/chitosan nanocomposites film shows enhanced electrocatalytic activity towards the reduction of H₂O₂ and the amperometric responses show a linear dependence on the concentration of H₂O₂ in a range of 0.5–27.5 mM and a low detection limit of 10 nM at the signal‐to‐noise ratio of 3. The time required to reach the 95% steady state response was less than 2 s. CV studies demonstrate that the modified electrode has outstanding stability. In addition, a glucose biosensor is further developed through the simple one‐step electrodeposition method. The observed wide concentration range, high stability and high reproducibility of the PB‐SWNTs/chitosan nanocomposites film make them promising for the reliable and durable detection of H₂O₂ and glucose.     

Sensitive Voltammetric Determination of Baicalein at Thermally Reduced Graphene Oxide Modified Glassy Carbon Electrode

This work presents a sensitive voltammetric method for determination of the flavonoid baicalein by using a thermally reduced graphene oxide (TRGO) modified glassy carbon electrode (GCE) in 100 mM KCl‐10 mM sodium phosphate buffer solution (pH 7.40). The surface morphology and structure of TRGO investigated by atomic force microscopy, FT‐IR spectroscopy and Raman spectroscopy reveal that the TRGO prepared maintained as single or bilayer sheets and with significant edge‐plane‐like defect sites. The TRGO/GCE modified electrode shows more favorable electron transfer kinetics for potassium ferricyanide and potassium ferrocyanide probe molecules, which are important electroactive compounds, compared with bare GCE and GO/GCE electrodes. The electrochemical behaviors of baicalein at the TRGO/GCE were investigated by cyclic voltammetry, suggesting that the TRGO/GCE exhibits excellent electrocatalytic activity to baicalein. Under physiological conditions, the modified electrode showed linear voltammetric response from 10 nM to 10 µM for baicalein, with a detection limit of 6.0 nM. This work demonstrates that the graphene‐modified electrode is a promising tool for electrochemical determination of flavonoid drugs.     

Characterization of gold nanoparticles electrochemically deposited on amine-functioned mesoporous silica films and electrocatalytic oxidation of glucose

This study reports the preparation and characterization of gold nanoparticles deposited on amine-functioned hexagonal mesoporous silica (NH₂–HSM) films and the electrocatalytic oxidation of glucose. Gold nanoparticles are fabricated by electrochemically reducing chloroauric acid on the surface of NH₂–HSM film, using potential step technology. The gold nanoparticles deposited have an average diameter of 80 nm and show high electroactivity. Prussian blue film can form easily on them while cycling the potential between −0.2 and 0.6 V (vs saturated calomel electrode) in single ferricyanide solution. The gold nanoparticles loading NH₂–HSM-film-coated glassy carbon electrode (Au–NH₂–HSM/GCE) shows strong catalysis to the oxidation of glucose, and according to the cathodic oxidation peak at about 0.16 V, the catalytic current is about 2.5 μA mM⁻¹. Under optimized conditions, the peak current of the cathodic oxidation peak is linear to the concentration of glucose in the range of 0.2 to 70 mM. The detection limit is estimated to be 0.1 mM. In addition, some electrochemical parameters about glucose oxidation are estimated.     

Potassium ion-selective electrode based on a cobalt(II)-hexacyanoferrate film-modified electrode

A potassium ion-selective electrode based on a cobalt(II)-hexacyanoferrate(III) (CHCF) film-modified glassy carbon electrode is proposed. The electroactive film is introduced onto the glassy carbon electrode surface by electrodeposition of cobalt, which forms a thin CHCF film on subsequent anodic scanning in KClHCl solution (pH 5.0–5.5) containing K₃Fe(CN)₆. The thickness of the film on the electrode surface can be controlled by changing the electrodeposition time and the concentrations of cobalt(II) and Fe(CN)^3?₆ ions. The modified electrode exhibits a linear response in the concentration range 1 × 10^?1 ?3 × 10^?5 M potassium ion activity, with a near-Nernstian slope (48–54 mV per decade) at 25 ± 1°C. The detection limit is 1 × 10^?5 M. The stability, response time and selectivity were investigated. The electrode exhibits good selectivity for potassium ion with the twelve cations investigated. The relative standard deviation is 1.5% (n=10). The effects of the thickness of the electroactive film and the pH of the solution on the electrode response were also investigated.     

Permselectivity of neurotransmitters at overoxidized polypyrrole-film-coated glassy carbon electrodes

The permselectivity of neurotransmitters such as dopamine, epinephrine, and norepinephrine at overoxidized polypyrrole (OPPY)-film-coated glassy carbon electrodes has been investigated. The chemically-modified electrodes exhibit attractive permselectivity and antifouling properties of rejecting anionic species, e.g. ascorbate, etc. Compared with the response of neurotransmitters at modified electrodes overoxidized in phosphate buffer solution (pH 7.4), higher sensitivity and reversibility response can be obtained at modified electrodes overoxidized in sodium hydroxide solution. The effect of film thickness on the permselective response was tested. Rotating disk electrode experiments were used to determine the apparent diffusion coefficients of several electroactive solutes in the OPPY films. The influence of the hydrophobicity of the organic ions on the permeability within the polymer films was discussed. Dopamine and epinephrine were determined at the 1 x 10(-6)-1 x 10(-4) M level by means of voltammetry after an exposure period of 2 min in 0.1 M phosphate buffer (pH 7.4) with detection limits of 8 x 10(-7) M and 6 x 10(-7) M respectively.     

Study on Electrochemiluminesce of Ru(bpy3)2+ Immobilized in a Titania Sol‐Gel Membrane

The immobilization of tris(2,2′‐bipyridyl)ruthenium(II), Ru(bpy)₃²⁺, at a glassy carbon electrode was achieved by entrapping the Ru(bpy)₃²⁺ in a vapor deposited titania sol‐gel membrane. The electrogenerated chemiluminescence (ECL) of the immobilized Ru(bpy)₃²⁺ was studied. The Ru(bpy)₃²⁺ modified electrode showed a fast ECL response to both oxalate and proline. The ECL intensity was linearly related to concentrations of oxalate and proline over the ranges from 20 to 700 μmol L^?1 and 20 to 600 μmol L^?1, respectively. The detection limits for oxalate and proline at 3σ were 5.0 μmol L^?1 and 4.0 μmol L^?1, respectively. This electrode possessed good precision and stability for oxalate and proline determinations. The electrogenerated chemiluminescence mechanism of proline system was discussed. This work provided a new way for the immobilization of Ru(bpy)₃²⁺ and the application of titania sol‐gel membrane in electrogenerated chemiluminescence.     

Electrochemical impedance spectroscopy study of cuprous oxide films formed on copper: effect of pH and sulfate and carbonate ions

The semiconducting properties of anodic passive films formed potentiostatically on polycrystalline copper in aqueous borax solutions were studied using electrochemical impedance spectroscopy, photocurrent spectroscopy and ellipsometric measurements. The semiconducting nature of the cuprous passive layer was analysed as a function of pH (9.2>pH>7.4), electrode potential and with the addition of 3.5 mM Na₂CO₃ and 8 mM Na₂SO₄. The different growth conditions change the compactness and the defect or excess of cations accumulated in the compact inner cuprous layer, leading to different semiconducting properties. Electronic Publication     

Electrochemiluminescence from Ru(bpy)3 immobilized in poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate)-poly(vinyl alcohol) composite films

Electrochemical behavior and electrogenerated chemiluminescence (ECL) of tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) immobilized in poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate)-poly(vinyl alcohol) (PEDOT/PSS-PVA) composite films via ion-exchange have been investigated with tripropylamine (TPA) as the co-reactant at a glassy carbon electrode. The immobilized Ru(bpy)₃²⁺ performed a surface-controlled electrode reaction. The Ru(bpy)₃²⁺ modified electrode showed a fast ECL response to TPA, and was used for the ECL detection of TPA with high sensitivity. The ECL intensity was linearly related to concentrations of TPA over the range from 0.50 μmol L⁻¹ to 0.80 mmol L⁻¹, and the detection limit was 0.10 μmol L⁻¹ (S/N = 3). The as-prepared electrode exhibited good precision and long-term stability for TPA determination.     

Amperometric detection of hydrazine by cyclic voltammetry and flow injection analysis using ruthenium modified glassy carbon electrodes

Glassy carbon electrodes modified with (5-amino-1,10-phenanthroline)bis(bipyridine)ruthium(II) chloride hydrate, [(bpy)₂Ru(5-phenNH₂)]Cl₂·H₂O, are shown to oxidize hydrazine with excellent sensitivity. The presence of an amine group on the ruthenium complex facilitates electropolymerization onto the electrode surface. Using cyclic voltammetry, a large catalytic current is observed upon oxidation of hydrazine in phosphate buffer (pH 5.0), compared to the current obtained from the ruthenium-modified electrode with no hydrazine present. The sensitivity of cyclic voltammetry is sufficient for obtaining a linear calibration curve for hydrazine over the range of 10⁻⁵ to 10⁻² M. Hydrodynamic amperometry was used to determine the working potential for flow injection analysis. The limit of detection for hydrazine was determined to be 8.5 μM using FIA. The thickness of these films was shown to increase linearly with the number of electropolymerization cycles, in the range of 1000-2500 nm for 5-20 cycles, respectively, using Rutherford backscattering spectrometry (RBS). RBS analysis also suggests that the film is multilayered with the outermost layers containing a high ruthenium concentration, followed by layers where the concentration of ruthenium decreases linearly and approaches zero at the electrode surface.     

Amperometric hydrogen peroxide biosensor based on a glassy carbon electrode modified with polythionine and gold nanoparticles

We report on a novel hydrogen peroxide biosensor that was fabricated by the layer-by-layer deposition method. Thionine was first deposited on a glassy carbon electrode by two-step electropolymerization to form a positively charged surface. The negatively charged gold nanoparticles and positively charged horseradish peroxidase were then immobilized onto the electrode via electrostatic adsorption. The sequential deposition process was characterized using electrochemical impedance spectroscopy by monitoring the impedance change of the electrode surface during the construction process. The electrochemical behaviour of the modified electrode and its response to hydrogen peroxide were studied by cyclic voltammetry. The effects of the experimental variables on the amperometric determination of H₂O₂ such as solution pH and applied potential were investigated for optimum analytical performance. Under the optimized conditions, the biosensor exhibited linear response to H₂O₂ in the concentration ranges from 0.20 to 1.6?mM and 1.6 to 4.0?mM, with a detection limit of 0.067?mM (at an S/N of 3). In addition, the stability and reproducibility of this biosensor was also evaluated and gave satisfactory results.

Electrochemical Detection of Dopamine at Fe3O4/SPEEK Modified Electrode

Reported here is the design of an electrochemical sensor for dopamine (DA) based on a screen print carbon electrode modified with a sulphonated polyether ether ketone-iron (III) oxide composite (SPCE-Fe₃O₄/SPEEK). L. serica leaf extract was used in the synthesis of iron (III) oxide nanoparticles (Fe₃O₄NPs). Successful synthesis of Fe₃O₄NP was confirmed through characterization using Fourier transform infrared (FTIR), ultraviolet–visible light (UV–VIS), X-ray diffractometer (XRD), and scanning electron microscopy (SEM). Cyclic voltammetry (CV) was used to investigate the electrochemical behaviour of Fe₃O₄/SPEEK in 0.1 M of phosphate buffer solution (PBS) containing 5 mM of potassium ferricyanide (III) solution (K₃[Fe(CN)₆]). An increase in peak current was observed at the nanocomposite modified electrode SPCE-Fe₃O₄/SPEEK) but not SPCE and SPCE-Fe₃O₄, which could be ascribed to the presence of SPEEK. CV and square wave voltammetry (SWV) were employed in the electroxidation of dopamine (0.1 mM DA). The detection limit (LoD) of 7.1 μM and 0.005 μA/μM sensitivity was obtained for DA at the SPCE-Fe₃O₄/SPEEK electrode with concentrations ranging from 5–50 μM. LOD competes well with other electrodes reported in the literature. The developed sensor demonstrated good practical applicability for DA in a DA injection with good resultant recovery percentages and RSDs values.     

Metal-metal oxide enzyme electrodes for the determination of urea

Enzyme electrodes for urea assay based on metal-metal oxide (Sb, Bi, W, Ti + RuO₂) with urease immobilized in gelatin gel were examined. It was shown that the best electrodes were obtained for tungsten. The urea response of the electrodes was influenced by the pH and concentration of the buffer used. Increasing additions of inert salt (potassium chloride) change the pH characteristic of the tungsten electrode and buffer capacity, thus influencing the urea response of the electrode.     

Direct electrochemistry and electrocatalysis of horseradish peroxidase immobilized in sol–gel-derived tin oxide/gelatin composite films

Horseradish peroxidase (HRP) was immobilized into a new type of sol–gel-derived nano-sized tin oxide/gelatin composite film (SnO₂ composite film) using a sol–gel film/enzyme/sol–gel film “sandwich” configuration. Direct electrochemistry and electrocatalysis of HRP incorporated into the composite films were investigated. HRP/SnO₂ composite film exhibited a pair of stable and quasi-reversible cyclic voltammetric peaks for the HRP Fe(III)/HRP Fe(II) redox couple with a formal potential of about −0.25 V (vs. SCE) in a pH 6.0 phosphate buffer solution. The electron transfer between the enzyme and the underlying electrode was greatly enhanced in the microenvironment with nano-SnO₂ particles and nanoporous structures. Morphologies and microstructures of the composite films and HRP/composite films were characterized with TEM, AFM. Electrochemical impedance spectroscopy (EIS) was also used to feature the HRP incorporated into composite films. FTIR and UV–Vis spectroscopy demonstrated that HRP in the composite film could retain its native secondary structure. With the advantages of organic–inorganic hybrid materials, the HRP/SnO₂ composite film modified electrode displayed good stability and electrocatalytic activity to the reduction of H₂O₂, The apparent Michaelis-Menten constant was estimated to be 0.345 mM, indicating a high affinity of HRP entrapped into the composite film toward H₂O₂.     

Electrocatalysis and Amperometric Detection of the Reduced Form of Nicotinamide Adenine Dinucleotide at Toluidine Blue/Zinc Oxide Coated Electrodes

Thin toluidine blue (TBO) and zinc oxide (ZnO) hybrid films have been grown on glassy carbon electrode (GCE) and indium tin oxide coated (SnO₂) glass electrodes by using cyclic voltammetry (CV). Scanning electron microscopy (SEM) images revealed spherical and beads‐like shape of highly oriented TBO/ZnO hybrid films. Energy dispersive spectrometry (EDS) results declared that the films composed mainly of Zn and O. Moreover, TBO/ZnO hybrid films modified electrode is electrochemically active, dye molecules were not easily leached out from the ZnO matrix and the hybrid films can be considered for potential applications as sensor for amperometric determination of reduced nicotinamide adenine dinucleotide (NADH) at 0.0 V. A linear correlation between electrocatalytic current and NADH concentration was found to be in the range between 25 μM and 100 μM in phosphate buffer. In addition, we observed that dopamine, ascorbic acid and uric acid are not interference in amperometric detection of NADH in this proposed method. In addition, TBO/ZnO hybrid film modified electrode was highly stable and its response to the NADH also remained relentless.     

Enzyme-free impedimetric glucose sensor based on gold nanoparticles/polyaniline composite film

A non-enzymatic impedimetric glucose sensor was fabricated based on the adsorption of gold nanoparticles (GNPs) onto conductive polyaniline (PANI)-modified glassy carbon electrode (GCE). The modified electrode (GCE/PANI/GNPs) was characterized by using cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and scanning electron microscopy (SEM). The determination of glucose concentration was based on the measurement of EIS with the mediation of electron transfer by ferricyanide ([Fe(CN)₆]^3?). The [Fe(CN)₆]^3? is reduced to ferrocyanide ([Fe(CN)₆]^4?), which in turn is oxidized at GCE/PANI/GNPs. An increase in the glucose concentration results in an increase in the diffusion current density of the [Fe(CN)₆]^4? oxidation, which corresponds to a decrease in the faradaic charge transfer resistance (R _ct). A wide linear concentration range from 0.3 to 10 mM with a lower detection limit of 0.1 mM for glucose was obtained. The proposed sensor shows high sensitivity, good reproducibility, and stability. In addition, the sensor exhibits no interference from common interfering substances such as ascorbic acid, acetaminophen, and uric acid.     

Isolation,purification, and study of some properties of the extracellular lignin peroxidases of the wood-destroying fungusPleurotus ostreatus

Abstact Two bands with lignin peroxidase activity have been detected by isoelectric focusing in a total enzyme preparation obtained from a 15-day filtrate of the culture liquid of the fungusPleurotus ostreatus by fractionation with ammonium sulfate. Two homogeneous forms of the enzymes — LGP-I and LGP-II — have been obtained by gel filtration on Sephadex G-100, ion-exchange chromatography on DEAF-Toyopearl 650 M gel, and rechromatography on Sephadex G-75, and also by electrophoresis in PAAG. The specific activities of the purified lignin peroxidases LGP-I and LGP-H amounted to 36.5 and 54.3 units/mg, their degrees of purification being 8.7 and 12.9, respectively. The molecular masses of LGP-I and LGP-II, determined by electrophoresis in PAAG in the presence of Na-DS and by gel filtration on TSK HW–65 gel were 42–44 and 61–63 kDa. The isoelectric points of LGP-I and LGP-II were 3.4 and 4.1, their pH optima 2.7 and 3.4, and the, temperatures of their optimum enzymatic action 28 and 34°C, respectively. The isoenzymes differed from one another substantially with respect to pH stability and resistance to heat. The values of K_M determined from the rates of hydrolysis of the substrate by the enzymes in the presence of H₂O₂ at pH 3.7 were 0.09 mM for LGP-I and 0.07 mM for LGP-II. The values of K_M with respect to veratryl alcohol, determined by the Lineweaver—Burk method, were 0.117 mM for LGP-II and 0.132 mM for LGP-II.Institute of Microbiology, Academy of Sciences of the Republic of Uzbekistan, Tashkent, fax (3712) 41 71 29. Translated from Khimiya Prirodnykh Soedinenii, No. 3, pp. 394–402, May–June, 1996. Original article submitted November 11, 1994.     

Fabrication and characterization of Meldola's blue/zinc oxide hybrid electrodes for efficient detection of the reduced form of nicotinamide adenine dinucleotide at low potential

We report the synthesis and the electrochemical properties of hybrid films made of zinc oxide (ZnO) and Meldola's blue dye (MB) using cyclic voltammetry (CV). MB/ZnO hybrid films were electrochemically deposited onto glassy carbon, gold and indium tin oxide-coated glass (ITO) electrodes at room temperature (25 ± 2 °C) from the bath solution containing 0.1 M Zn(NO₃)₂, 0.1 M KNO₃ and 1 × 10⁻⁴ M MB. The surface morphology and deposition kinetics of MB/ZnO hybrid films were studied by means of scanning electron microscopy (SEM), atomic force microscopy (AFM) and electrochemical quartz crystal microbalance (EQCM) techniques, respectively. SEM and AFM images of MB/ZnO hybrid films have revealed that the surfaces are well crystallized, porous and micro structured. MB molecules were immobilized and strongly fixed in a transparent inorganic matrix. MB/ZnO hybrid films modified glassy carbon electrode (MB/ZnO/GC) showed one reversible redox couple centered at formal potential (E⁰′) −0.12 V (pH 6.9). The surface coverage (Γ) of the MB immobilized on ZnO/GC was about 9.86 × 10⁻¹² mol cm⁻² and the electron transfer rate constant (ks) was determined to be 38.9 s⁻¹. The MB/ZnO/GC electrode acted as a sensor and displayed an excellent specific electrocatalytic response to the oxidation of nicotinamide adenine dinucleotide (NADH). The linear response range between 50 and 300 μM NADH concentration at pH 6.9 was observed with a detection limit of 10 μM (S/N = 3). The electrode was stable during the time it was used for the full study (about 1 month) without a notable decrease in current. Indeed, dopamine (DA), ascorbic acid (AA), acetaminophen (AP) and uric acid (UA) did not show any interference during the detection of NADH at this modified electrode.     

Iodide-induced adsorption of lead(II) ion on a glassy carbon electrode modified with ferroferric oxide nanoparticles

Spherical Fe₃O₄ nanoparticles (NPs) were prepared by hydrothermal synthesis and characterized by scanning electron microscopy and X-ray diffraction. A glassy carbon electrode was modified with such NPs to result in a sensor for Pb(II) that is based on the strong inducing adsorption ability of iodide. The electrode gives a pair of well-defined redox peaks for Pb(II) in pH 5.0 buffer containing 10 mM concentrations of potassium iodide, with anodic and cathodic peak potentials at ?487 mV and ?622 mV (vs. Ag/AgCl), respectively. The amperometric response to Pb(II) is linear in the range from 0.10 to 44 nM, and the detection limit is 40 pM at an SNR of 3. The sensor exhibits high selectivity and reproducibility.

Solid‐State Electrochemistry and Electrochemiluminescence of Porous Thin Film of [(2,2′‐Bipyridyl)(4‐(2‐pyrrol‐1‐ylethyl)‐4′‐methyl‐2,2′‐bipyridyl)2]ruthenium(II) Monomer Precipitation

A novel fluorescent porous thin film based on the precipitation of the [(2,2′‐bipyridyl)(4‐(2‐pyrrol‐1‐ylethyl)‐4′‐methyl‐2,2′‐bipyridyl)₂]ruthenium(II) (BF₄)₂ complex (pyr‐Ru) was fabricated by easily spreading 2 µL of pyr‐Ru (1 mM in acetonitrile solution) onto the surface of a platinum electrode and drying it in ambient conditions. The morphology of the resulting pyr‐Ru thin film was characterized by scanning electron microscopy (SEM) and fluorescence microscopy. The coating exhibits fluorescent properties of the ruthenium complex and a porous structure with pore diameters of micrometers. The solid‐state electrochemistry and electrochemiluminescence behaviors of the porous pyr‐Ru thin film were investigated in aqueous solution by cyclic voltammetry and step potential.     

Voltammetric Determination of Hesperidin on the Electrode Modified with SnO2 Nanoparticles and Surfactants

Highly sensitive voltammetric method for hesperidin determination is developed using glassy carbon electrode modified with SnO₂ nanoparticles (SnO₂ NPs) and surfactants. The highest oxidation currents of hesperidin are observed in the case of cationic 0.50 mM cetylpyridinium bromide (CPB). Parameters of hesperidin electrooxidation have been calculated. Adsorptive anodic differential pulse voltammetry (AdADPV) in phosphate buffer pH 7.0 after 120 s accumulation provides linear dynamic ranges of 0.10–10 and 10–75 μM with the detection limit of 0.077 μM. The selectivity of hesperidin response is proved in the presence of inorganic ions, saccharides, ascorbic acid and other natural phenolics.