Ti-O共掺杂石墨烯的电子结构和光学性质的理论研究

本文利用基于密度泛函理论的第一性原理方法研究了本征石墨烯和不同掺杂浓度下Ti-O共掺杂石墨烯的电子结构和光学性质,并讨论了其内部的微观机制.研究结果表明:本征石墨烯是一种零带隙材料,狄拉克点在费米能级面上,其在紫外光区的光吸收强度较强.Ti-O共掺杂石墨烯可以很好的打开石墨烯的带隙和提高石墨烯的光催化强度,Ti18-O18@G模型费米能级附近的态密度主要由C-p轨道、Ti-d轨道和O-p轨道杂化而成.Ti18-O18@G模型在可见光区的吸收谱强度最大,主要归因于其内部晶格畸变、带隙被打开和杂质能带的出现,这些因素可以促进电子空穴对的产生和分离,从而使石墨烯在可见光区的光催化能力得到增强.本研究结果可为开发高催化活性的石墨烯提供理论依据.     

La掺杂3C-SiC电子结构和光学性质的第一性原理研究

采用基于密度泛函理论的第一性原理计算方法,对未掺杂及稀土材料La掺杂3C-SiC的电子结构和光学性质进行理论计算.计算结果表明,La掺杂引起3C-SiC晶格体积增大,掺杂体系能量更小,掺杂体系的结构更稳定;未掺杂3C-SiC是直接带隙半导体,其禁带宽度为1.406 eV,La掺杂后带隙宽度下降为1.161 eV,La掺杂3C-SiC引入了3条杂质能级,能量较高的1条杂质能级与费米能级发生交叠,另外2条杂质能级都在费米能级以下价带顶之上,La掺杂引起3C-SiC吸收谱往低能区移动,未掺杂3C-SiC的静态介电常数为2.66,La掺杂引起静态介电常数增加为406.01,La掺杂3C-SiC是负介电半导体材料.     

第一性原理计算C掺杂金红石型TiO_2的磁性和光学性质

本文运用第一性原理GGA+U方法计算了C元素单/双掺杂金红石型TiO_2的电子结构、磁性和光学性质.结果表明,C掺杂体系的晶格发生畸变和体积相应增大.单掺杂体系的磁矩为1.3μB,磁矩主要归因于杂质态引起的自旋电荷密度不平衡,杂质态主要由C-2p、O-2p和Ti-3d的态电子构成,且它们之间存在明显的杂化现象.双掺杂体系中C原子之间的反铁磁性耦合比铁磁性耦合更加稳定,但其磁矩为零.另外,随着掺杂浓度的增大,掺杂体系的带隙由2.58 eV增大到3.4 eV,且在可见光区域的光吸收效率明显增大.这表明带隙的减小可能不是光谱吸收增强的主要因素,而带隙中的杂质态极大地影响了光谱吸收效率.     

La-N共掺杂锐钛矿相TiO_2的电子结构及光学性质的第一性原理研究

利用基于密度泛函理论的第一性原理平面波超软赝势方法对锐钛矿相TiO_2、La单掺杂及La-N共掺杂锐钛矿相TiO_2的电子结构进行计算,分析La单掺杂及La-N共掺杂对锐钛矿相TiO_2的晶体结构、能带、态密度、差分电荷密度和光吸收性质的影响.结果表明,掺杂后TiO_2的晶格发生畸变,原子间键长的变化使晶格发生膨胀;掺杂后TiO_2的禁带宽度减小,并在禁带中引入杂质能级,导致TiO_2的吸收图谱产生红移现象;与La单掺杂相比,La-N共掺杂锐钛矿相TiO_2的红移程度增强.     

镧系元素掺杂TiO_2的电子和光学特性的第一性原理计算

基于密度泛函理论的第一性原理局部密度近似法,结合Hubbard U校正(LDA+U),研究了镧系元素掺杂的锐钛矿型TiO_2的取代能、热力学电荷跃迁能级和光学性质.除La之外的所有镧系元素,在掺杂时向主带隙中引入杂质态.所得取代能表明了镧系元素掺杂TiO_2的可行性.同时预测了最佳掺杂比例约为3%,由Ce、Nd、Sm、Gd或Tm掺杂引入的掺杂能级具有负U特性.另外,所得热力学跃迁能级预测了Lu在主带隙内不发生电荷跃迁.算出的光吸收系数表明镧系元素掺杂可使TiO_2具有可见光吸收性能.     

第一性原理计算C掺杂金红石型TiO2的磁性和光学性质

本文运用第一性原理GGA+U方法计算了C元素单/双掺杂金红石型TiO2的电子结构、磁性和光学性质. 结果表明, C掺杂体系的晶格发生畸变和体积相应增大。单掺杂体系的磁矩为1.3 μB, 磁矩主要归因于杂质态引起的自旋电荷密度不平衡, 杂质态主要由C-2p、O-2p 和Ti-3d的态电子构成, 且它们之间存在明显的杂化现象. 双掺杂体系中C原子之间的反铁磁性耦合比铁磁性耦合更加稳定, 但其磁矩为零. 另外, 随着掺杂浓度的增大, 掺杂体系的带隙由2.58 eV增大到3.4 eV, 且在可见光区域的光吸收效率明显增大. 这表明带隙的减小可能不是光谱吸收增强的主要因素, 而带隙中的杂质态极大地影响了光谱吸收效率.     

镧系元素掺杂TiO_2的电子和光学特性的第一性原理计算

基于密度泛函理论的第一性原理局部密度近似法,结合Hubbard U校正(LDA+U),研究了镧系元素掺杂的锐钛矿型TiO_2的取代能、热力学电荷跃迁能级和光学性质.除La之外的所有镧系元素,在掺杂时向主带隙中引入杂质态.所得取代能表明了镧系元素掺杂TiO_2的可行性.同时预测了最佳掺杂比例约为3%,由Ce、Nd、Sm、Gd或Tm掺杂引入的掺杂能级具有负U特性.另外,所得热力学跃迁能级预测了Lu在主带隙内不发生电荷跃迁.算出的光吸收系数表明镧系元素掺杂可使TiO_2具有可见光吸收性能.     

镧系元素掺杂TiO_2的电子和光学特性的第一性原理计算

基于密度泛函理论的第一性原理局部密度近似法,结合Hubbard U校正(LDA+U),研究了镧系元素掺杂的锐钛矿型TiO_2的取代能、热力学电荷跃迁能级和光学性质.除La之外的所有镧系元素,在掺杂时向主带隙中引入杂质态.所得取代能表明了镧系元素掺杂TiO_2的可行性.同时预测了最佳掺杂比例约为3%,由Ce、Nd、Sm、Gd或Tm掺杂引入的掺杂能级具有负U特性.另外,所得热力学跃迁能级预测了Lu在主带隙内不发生电荷跃迁.算出的光吸收系数表明镧系元素掺杂可使TiO_2具有可见光吸收性能.     

M-(Sm,Pr, Ga)掺杂TiO_2带隙及电子结构的第一原理研究（英文）

采用密度泛函理论对M-(Sm、Pr、Ga)掺杂锐钛矿型TiO_2能带和电子性质进行了系统的理论研究.计算结果表明,通过Sm和Pr的掺杂可以降低TiO_2的带隙进而使其产生吸收边红移,通过Ga的掺杂能使带隙稍增加.这主要是由于Sm和Pr的掺杂使Sm和Pr上的4f层电子与原子相邻O原子上的2p层电子相互作用,形成的杂质能级影响了Ti-O的能带结构,从而降低带隙,提高TiO_2的可见光吸收性能.     

第一性原理研究Mn和Cu掺杂六钛酸钾(K_2Ti_6O_(13))的电子结构和光学性质

六钛酸钾(K_2Ti_6O_(13))是宽带隙半导体光催化材料,只能响应波长较短的紫外光.为了使K_2Ti_6O_(13)对可见光响应,本文采用第一性原理方法,研究过渡金属Mn和Cu掺杂改性后K_2Ti_6O_(13)的电子结构和光学性质.计算结果表明:Mn,Cu掺杂后K_2Ti_6O_(13)禁带中出现了杂质能级,这些杂质能级由O 2p和Ti 3d与Mn 3d或Cu 3d态杂化而成.对于Mn掺杂的K_2Ti_6O_(13),其带隙值变小,位于能带中间的杂质能级可作为电子跃迁的桥梁,从而实现了对可见光的吸收.对于Cu掺杂的K_2Ti_6O_(13),其带隙值虽略有增大,但是若考虑将与价带相连的杂质能级,带隙值将大大减小,且此杂质能级可抑制光生载流子的复合,使得掺杂后K_2Ti_6O_(13)吸收带边红移至可见光区并在可见光范围内吸收强度明显增强.总的而言,Mn,Cu的掺杂实现了钛酸钾对可见光的吸收,同时Cu掺杂的效果要优于Mn掺杂的效果.研究结果对K_2Ti_6O_(13)在光催化领域上的应用具有重要的意义.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.