陶瓷纤维对普通硅酸盐混凝土的强韧化效应

 采用液压试验机和Φ100 mm分离式霍普金森压杆实验装置,研究了体积分数为0.1%、0.2%和0.3%的陶瓷纤维混凝土的准静态和动态力学性能,分析了陶瓷纤维的增强机理,并将其与相同纤维体积分数的碳纤维混凝土进行对比。结果表明：陶瓷纤维改善了普通硅酸盐混凝土的准静态力学性能;纤维体积分数为0.3%时,抗压强度提高15.0%,劈裂抗拉强度提高8.5%,抗折强度提高12.7%。冲击荷载作用下,陶瓷纤维混凝土的动态抗压强度和比能量吸收随平均应变率的增加近似线性增长;体积分数为0.2%时,陶瓷纤维的增强、增韧效果最佳。陶瓷纤维对普通硅酸盐混凝土的增强、增韧效果总体上优于碳纤维。     

The effect of surface treatment of carbon fiber on the flexural property of thermoplastic polyimide composite

Rare earth solution (RES) surface modification and air-oxidation methods were used to improve the interfacial adhesion of the carbon fiber reinforced polyimide (CF/PI) composite. The flexural property of the PI composites reinforced by the carbon fibers treated with different surface modification methods was comparatively investigated. Results showed that the flexural strength of CF/PI composite was improved after RES treatment. The improvement of impact and flexural property of the CF/PI composite was mainly due to the improvement in interfacial adhesion after RES treatment. X-ray photoelectron spectroscopy (XPS) study of carbon fiber surface showed that the oxygen concentration was obviously increased after RES treatment. The increase in the amount of organic functional groups increased the interfacial adhesion between CF and PI matrix.     

A Numerical Investigation on the Influence of Steel Fiber Shape and Interface Strength in Reinforced Concrete

Not all steel fiber reinforced concrete composites are equally effective in enhancing structural performance. Their mechanical behaviour strongly depends upon the reinforcement morphology as well as the properties of the interface lying between steel reinforcement and concrete matrix. Using bone-shaped short (BSS) steel fibers, instead of conventional straight short (CSS) steel fibers, to reinforce concrete has demonstrated their potential in improving toughness, ductility and energy absorbing capacity under impact significantly and simultaneously. Accomplishing a strong steel–concrete interface leads to a slight increase in composite strength but simultaneously to a significant decrease in its toughness. Due to the sensitivity of steel reinforced concrete performance on these complex geometric and material parameters, the development of a numerical tool capable of simulating accurately the composite mechanical behaviour and thus leading to optimized design solutions is desirable. The physical problem of the present work involves a typical concrete composite uniformly reinforced with steel fibers subjected to tensional loading. A micromechanical non-linear finite element formulation is utilized in order to predict the load transfer characteristics and the failure process. A linear material behaviour is assumed for the steel component; a non-linear multi-crack material response is used to describe concrete while a mix-mode bilinear behaviour is utilized for the interface providing separation of primary material phases. Numerical results are presented in terms of the global design parameters. The influence of the fiber end shape, the interface strength and the fiber volume fraction on the composite strength and toughness is addressed and consequently optimized design preferences arise.     

Attenuation of flexural vibration for floating floor and floating box induced by ground vibration

This paper investigates the vibration isolation performance of floating floor and floating box structures to control rail vibration transmission. Simple theoretical and experimental methods are developed to analyze the effects of stiffener beam, mass and arrangement of isolator on the fundamental natural frequency of the flexural vibration of floating floor and box structure.The vibration reduction performances of floating floor and box structure are found to be degraded by flexural vibration of the floor or supporting stiffener beam. From the results of vibration measurements; stiffener beams increase the fundamental natural frequency of flexural vibration of floating floor and enhance vibration isolation. Also they can further alleviate the effect of flexural vibration using optimum isolator arrangement effectively. The proposed floating box design achieved a vibration reduction of 15-30 dB in frequency region of critical rail vibration (30-200 Hz).     

Conduction noise absorption by fiber-reinforced epoxy composites with carbon nanotubes

Nearly all electronic equipment is susceptible to malfunction as a result of electromagnetic interference. In this study, glass fiber, and carbon fiber as a type reinforcement and epoxy as a matrix material were used to fabricate composite materials. In an attempt to increase the conduction noise absorption, carbon nanotubes were grown on the surface of glass fibers and carbon fibers. A microstrip line with characteristic impedance of 50 Ω in connection with network analyzer was used to measure the conduction noise absorption. In comparing a glass fiber/epoxy composite with a GF-CNT/Ep composite, it was demonstrated that the CNTs significantly influence the noise absorption property mainly due to increase in electric conductivity. In the carbon fiber composites, however, the effectiveness of CNTs on the degree of electric conductivity is negligible, resulting in a small change in reflection and transmission of an electromagnetic wave.     

Fabrication and Flexural Properties of Bagasse Fiber Reinforced Biodegradable Composites

Biodegradable composites made from bagasse fiber and biodegradable resin were fabricated and the flexural properties of the composites investigated in terms of the effects of fiber length, fiber volume fraction, and different alkali treatments of the bagasse fibers. The flexural properties of the composites increased with the increase in fiber length but decreased below the critical fiber length. The flexural properties increased with the increase in fiber volume fraction. The scanning electron microscope (SEM) micrographs showed that compression of the cellulose structure of bagasse fiber after preparation could have caused enhancement in the flexural properties. Furthermore, when comparing the effects of different alkali treatments of the bagasse fibers, maximum improvement in the flexural properties was observed for the 1% NaOH solution treated fiber composites. After alkali treatment, fibrillation occurred and the surface of the treated fibers became finer; this could contribute to improvement in the fiber‐matrix adhesion and result in enhancing the flexural properties.     

Plasma treatment of carbon fibers: Non-equilibrium dynamic adsorption and its effect on the mechanical properties of RTM fabricated composites

The effect of oxygen plasma treatment on the non-equilibrium dynamic adsorption of the carbon fabric reinforcements in RTM process was studied. 5-Dimethylamino-1-naphthalene-sulfonylchloride (DNS-Cl) was attached to the curing agent to study the change of curing agent content in the epoxy resin matrix. Steady state fluorescence spectroscopy (FS) analysis was used to study this changes in the epoxy resin at the inlet and outlet of the RTM mould, and XPS was used to study the chemical changes on the carbon fiber surfaces introduced by plasma treatment. The interlaminar shear strength (ILSS) and flexural strength were also measured to study the effects of this non-equilibrium dynamic adsorption progress on the mechanical properties of the end products. FS analysis shows that the curing agent adsorbed onto the fiber surface preferentially for untreated carbon fiber, the curing agent content in the resin matrix maintain unchanged after plasma treatment for 3 min and 5 min, but after oxygen plasma treatment for 7 min, the epoxy resin adsorbed onto the fiber surface preferentially. XPS analysis indicated that the oxygen plasma treatment successfully increased some polar functional groups concentration on the carbon fiber surfaces, this changes on the carbon fiber surfaces can change the adsorption ability of carbon fiber to the resin and curing agent. The mechanical properties of the composites were correlated to this results.     

Relationship between the flexural properties and specimen aspect ratio in unidirectional composites

It is well known that the bending test provides a simple and convenient way of measuring the strength of unidirectional composite materials and gives very repeatable results. The aim of this research work was to study and analyze the flexural properties of unidirectional reinforced carbon fiber/epoxy (UD) specimens subjected to three-point loading. The effect of span-to-thickness ratio (L/h) and width-to-thickness ratio (b/h) on the three-point bending of UD composites has been investigated. Results have shown that unidirectional composites exhibit a transition in the failure mode from shear delamination to fiber yield with the span-tothickness ratio (L/h) is increased. The observed experimental data are confirmed by theoretical considerations presented here. Using the classical beam theory the conclusions of the tests could be extended by applying some reasonable requirements and simple rational fractional functions identified. This made it possible to express the asymptotic values of the flexural strength, the flexural modulus and apparent shear stress in a form that is independent from the values of the span-to-thickness ratio applied, and characterize the bending behavior of the composite materials at a more exact level.     

基于光纤光栅光谱分析的混凝土结构钢筋锈蚀监测

混凝土中钢筋发生锈蚀会严重影响混凝土结构的使用功能,文章提出了通过观察长周期光纤光栅(LPFG)的透射谱变化对混凝土结构中的钢筋锈蚀进行监测。这种方法基于长周期光纤光栅的微弯特性,利用其透射光谱随弯曲度增加逐渐变浅、谐振波长处的光功率与LPFG的弯曲度成线性这一特性,将钢筋锈蚀引起的钢筋径向膨胀转化为光栅的弯曲,通过监测光栅的光谱变化获知光栅的弯曲度进而判断钢筋的锈蚀程度,该方法对钢筋直接进行监测,简单易行,并利用光栅的光谱特性从而避免了环境温度、应变、折射率的影响,实验将光栅埋入到混凝土构件中,从已取得的实验结果来看,这种方法测量钢筋锈蚀厚度的准确度可达1.2 μm,可监测到的锈蚀厚度达3 mm,完全能够实现混凝土结构中钢筋锈蚀的早期至中期监测。     

Effect of fiber surface treatments on the fiber–matrix interaction in banana fiber reinforced polyester composites

Cellulosic fibers have been used as cost-cutting fillers in plastic industry. Among the various factors, the final performance of the composite materials depends to a large extent on the adhesion between the polymer matrix and the reinforcement and therefore on the quality of the interface. To achieve optimum performance of the end product, sufficient interaction between the matrix resin and the cellulosic material is desired. This is often achieved by surface modification of the resin or the filler. Banana fiber, the cellulosic fibers obtained from the pseudo-stem of banana plant (Musa sepientum) is a bast fiber with relatively good mechanical properties. The fiber surface was modified chemically to bring about improved interfacial interaction between the fiber and the polyester matrix. Various silanes and alkali were used to modify the fiber surface. Modified surfaces were characterized by SEM and FTIR. The polarity parameters of the chemically modified fibers were investigated using the solvatochromic technique. The results were further confirmed by electrokinetic measurements. Chemical modification was found to have a profound effect on the fiber–matrix interactions. The improved fiber–matrix interaction is evident from the enhanced tensile and flexural properties. The lower impact properties of the treated composites compared to the untreated composites further point to the improved fiber–matrix adhesion. In order to know more about the fiber–matrix adhesion, fractured surfaces of the failed composites where further investigated by SEM. Of the various chemical treatments, simple alkali treatment with NaOH of 1% concentration was found to be the most effective. The fiber–matrix interactions were found to be dependent on the polarity of the modified fiber surface.     

Effects of plasma surface modification on the mechanical properties of carbon fiber and carbon fiber/epoxy composite

_The effect of surface treatment on mechanical properties of carbon fibers has been investigated by application of plasma polymerization of selected monomers in the vapor phase. The role of the fiber-matrix interface on carbon fiber-reinforced epoxy resin composites has also been studied. Composites have been prepared separately by the use of plasma-modified and unmodified carbon fibers in the epoxy resin matrix. The mechanical properties of carbon fibers (Hercules and Grafil) as well as of fiber/epoxy composites were examined by using single filament and three-point bending tests, respectively. It was observed that plasma polymerization treatment at selected plasma conditions led to significant improvement of interlaminar shear and flexural strength values of composites.     

Discontinuous surface-treated submicron-diameter carbon filaments as an interlaminar filler in carbon fiber polymer-matrix composites for vibration reduction

Discontinuous surface-treated submicron-diameter carbon filaments are effective for use as an interlayer between continuous carbon fiber laminae in a nylon-6 matrix composite for enhancing the loss tangent (0.2 and 1.0 Hz) under flexure that involves bending of the fibers, without significant decrease of the flexural storage modulus or the tensile modulus or strength in the fiber direction. The surface treatment is oxidation using ozone. Without treatment, the filaments are not effective. The treated filaments amount to 0.64 vol.% of composite; the interlayer thickness is 77 μm. A viscoelastic interlayer is even more effective than the treated filament interlayer for enhancing the loss tangent, but the accompanying decrease in storage modulus is much more. The loss tangent for composite with viscoelastic interlayer decreases upon heating, so the loss modulus for this composite is less than that of the composite with treated filament interlayer at ?50°C.     

Mechanical and tribological enhancement of polyoxymethylene-based composites with long basalt fiber through melt pultrusion

Abstract

The polyoxymethylene (POM)/basalt fiber composites were prepared by use of long fiber-reinforced thermoplastic technology through melt pultrusion. The mechanical and tribological properties, morphology, and thermal stability of the resulting composites were investigated. The composites exhibit significant improvements in tensile, flexural, and notched impact strength. These mechanical strength and toughness are dependent on the fiber content over the full range of the study. The residual fiber length and distribution in the injection-molded specimens were characterized. The prominent reinforcement effect of basalt fiber on POM is derived from the supercritical fiber length, which is much longer than that of the short fiber-reinforced ones and thus makes the composites take full advantage of the strength of the reinforcing fibers. The Kelly–Tyson model was used to predict the ultimate tensile strength of POM composites using the measured values of residual fiber length in the matrix, but the deviations were observed at the high contents of basalt fiber. The morphologic investigation indicates that the fiber pullout and fiber breakage both contribute energy dissipation to the tensile fracture of the composites. The tribological characterization indicates that the friction coefficients and specific wear rates of POM composites also decrease remarkably. Such an improvement of tribological performance is due to the presence of the high wear-resistant basalt fibers on the top of the worn surface bearing the dynamic loadings under sliding. Moreover, the dynamic mechanical analysis reveals that the storage moduli of the composites increase with increasing the fiber content, whereas the loss factors present an opposite trend.     

相变材料蓄能式低温热水采暖地板热性能模拟

提出了一种采用定形相变材料蓄能的低温热水采暖地板形式。为了研究定形相变材料蓄能式低温热水采暖地板的传热性能,建立了该地板的传热分析模型。分析了相变材料的相变温度对地板表面平均热流密度和蓄能比的影响;比较了相变材料潜热蓄能地板与混凝土显热蓄能地板的热性能差异。结果表明:定形相变材料地板停止加热后仍可以在较长时间内保持稳定的热流密度。同时定形相变材料地板具有较大的蓄能比,使其夜间蓄存的热量可被更多地用于日间供热。     

一种弹性盘光纤加速度传感器的探讨

本文介绍了一种采用Ｍａｃｈ－Ｚｅｎｄｅｒ干涉仪结构的中心固支弹性盘光纤加速度传感器。该传感器利用弹性盘的变形引起光纤长度的变化，进而引起位相的变化，通过干涉仪感测出。文中分析了两种结构，并加以实现与对比。     

Performance of glass woven fabric composites with admicellar-coated thin elastomeric interphase

Adequate stress transfer between the inorganic reinforcement and surrounding polymeric matrix is essential for achieving enhanced structural integrity and extended lifetime performance of fiber-reinforced composites. The insertion of an elastomeric interlayer helps increase the stress-transfer capabilities across the fiber/matrix interface and considerably reduces crack initiation phenomena at the fiber ends. In this study, admicellar polymerization is used to modify the fiber/matrix interface in glass woven fabric composites by forming thickness-controlled poly(styrene-co-isoprene) coatings. These admicellar interphases have distinct characteristics (e.g. topology and surface coverage) depending on the surfactant/monomer ratios used during the polymerization reaction. Overall, the admicellar coatings have a positive effect on the mechanical response of resin transfer molded, E-glass/epoxy parts. For instance, ultimate tensile strength of composites with admicellar sizings improved 50–55% over the control-desized samples. Interlaminar shear strength also showed increases ranging from 18 to 38% over the same control group. Interestingly, the flexural properties of these composites proved sensitive to the type of interphase formed for various admicellar polymerization conditions. Higher surface coverage and film connectedness in admicellar polymeric sizings are observed to enhance stress transfer at the interfacial region.     

复合材料弹侵彻混凝土靶的研究

 利用碳纤维复合材料壳体和金属弹头组成的复合弹体,对混凝土靶进行了高速侵彻实验,弹体分别以336、447和517 m/s的速度对强度为30 MPa、厚度为200 mm的混凝土靶进行正侵彻和30°斜侵彻。实验结果表明：碳纤维复合材料壳体具有较高的强度,在高速侵彻靶体的过程中弹体结构能够保持完整,复合材料壳体没有纤维分层和断裂产生。相对于同样结构尺寸的金属弹体（将复合材料壳体替换为密度7.8 g/cm³的金属材料）,复合材料弹填充物的质量分数（18.5%）约为金属弹体的两倍,因此采用轻质高强复合材料替代高密度金属弹身,不仅可以提高弹体装填比、增加比毁伤威力,而且还具有较高的侵彻能力。     

Field emission of electrons from a single carbon fiber with a nanostructured emitting surface

The field emission of electrons from a single fine carbon fiber with a nanostructured emitting surface is studied experimentally. It is found that the fiber can serve as an effective field emitter of electrons at voltages of ∼10²–10³ under the conditions of technical vacuum and the emission current density may reach ∼10² A/cm². At a certain threshold voltage, the fiber starts executing flexural mechanical vibrations. The onset of mechanical vibrations is accompanied by a change in the field emission conditions. Namely, in the absence of vibrations, the mode of steady current extraction is observed. When mechanical vibrations set in, the field emission switches to the mode of current periodic oscillations with a constant component.     

Interfacial mechanical properties of carbon nanotube-deposited carbon fiber epoxy matrix hierarchical composites

Functionalized multiwalled carbon nanotubes were successfully deposited on carbon fibers using four different techniques including dip coating, hand layup, spray up and electrophoretic deposition (EPD). A uniform coating of nanotubes was achieved from EPD in comparison to other coating techniques. Later nanotube-coated fibers by EPD were introduced in epoxy resin to investigate interfacial mechanical properties of the developed hierarchical composites by vacuum bagging technique. The increases in flexural and interlaminar shear properties up to 15% and 18% were observed in composites containing nanotube-coated carbon fibers than composites with virgin carbon fibers, respectively. Microscopic observation revealed the proper impregnation of multiscale reinforcements, i.e., carbon fibers and carbon nanotubes, in resin along with the modification of fiber/matrix interface due to the presence of nanotubes at interface. Finally, the mechanisms for improved mechanical properties were identified along with the presentation of a schematic model for better understanding of the improved performance of hierarchical composite after depositing uniformly dispersed nanotubes on carbon fibers.     

Powder compaction,sintering, and rolling of ultra high molecular weight polyethylene and its composites

The applicability of powder compaction and sintering techniques to the processing of ultra high molecular weight polyethylene (UHMWPE) powder is demonstrated. With proper processing procedure and type of UHMWPE powder, the mechanical properties obtained are nearly equivalent to those obtained by conventional melt processes. The properties were optimized by selection of a sintering temperature just above the melting point and by close control of particle size and distribution. The processability of UHMWPE is dependent on the morphology of the powder. Only those powders with a fibrous morphology provided good mechanical properties after sintering. The mechanical properties of powder compacts can be improved by several techniques. Liquid sintering with added normal molecular weight polyethylene, with close control of particle size and distribution and amount of the second component, yielded improved properties. Composites of UHMWPE, with short glass and graphite fiber reinforcement, processed by powder compaction and sintering resulted in increased modulus. The properties of these composites depended upon the amount of fibers, fiber length, fiber-matrix bonding, and fiber orientation. Rolling the powder-processed UHMWPE oriented the structure and improved the mechanical properties, although it decreased the mechanical properties of the glass and graphite fiber composites because of debonding between fiber and matrix. The properties of carbon black—UHMWPE mixtures were improved by rolling because of a more uniform distribution of carbon black.