Photodegradation of Methanol Under UV–Visible Irradiation by Titania Dispersed on Polyester Cloth

Titania supported on polyester fabric (TiO₂–PY) with varying titania loadings (2–7 wt%) were prepared via the dip-coating method at room temperature using an aqueous slurry of anatase titania. Structural and morphological characterizations by X-ray diffraction and scanning electron microscopy revealed that the titanium dioxide crystallites deposited on the surface of the polyester fabric were in the micrometer range while their phase remained to be anatase. Photocatalytic activity of TiO₂–PY fabric catalysts was evaluated for vapor-phase oxidation of methanol in air as a test reaction in the presence of UV as well as solar radiation under ambient conditions. These catalysts were found to be quite active in both UV and solar irradiation with activity being higher in the former case. CO₂ yield from photo-oxidation of methanol depended on titania content and also on its dispersion over polyester fabric support.     

TiO2-Al2O3复合氧化物负载NiMo加氢脱硫催化剂的研究

采用溶胶凝胶技术，从Al2O3载体的表面改性出发，制备了TiO2-Al2O3复合载体。采用此改性载体制备了NiMo／TiO2-Al2O3催化剂；用中压固定床微反装置考察了载体改性对制备的催化剂的噻吩加氢脱硫(HDS)活性的影响．用透射电镜、NH3-TPD及吡啶红外光谱法对改性载体和催化剂进行了表征．结果表明，经钛溶胶改性的载体制备的催化剂与原有载体制备的催化剂相比，催化剂活性提高了20％．改性载体表面负载的钛溶胶以纳米尺寸的TiO2微粒形态存在．     

Effect of UV and visible light on photocatalytic reduction of lead and cadmium over titania based binary oxide materials

Uniform sized silica and zirconia mixed titania samples were prepared in presence of a surfactant (CETAB) using controlled hydrolysis of corresponding metal alkoxides. Photocatalytic activity towards reduction of lead and cadmium metal in aqueous solution was evaluated both in UV and visible light in a 100 ml capacity reactor. In particular mixing of 10 wt% silica with titania not only increases the surface area of the material but also increases the photocatalytic activity in UV light. Whereas mixing of zirconia with titania proved to be beneficial for visible light reaction. However, addition of hole scavenger increases the activity many folds and complete removal of Pb(2+) and Cd(2+) was possible in 60 min of reaction using synthesized catalysts. Among all the organic hole scavengers used, sodium formate is found to be the most active one. Interestingly quite high metal removal (89%) is also observed in presence of visible light within 60 min of reaction. Thus the above study indicates that the presence of certain oxides in low quantity (10 wt%) with titania can facilitates the photocatalytic process selectively in UV as well as visible light.     

Preparation and characterization of vanadium oxide deposited on thermally stable mesoporous titania

Vanadium oxide was deposited on mesoporous titania by the molecular designed dispersion method to investigate the potential properties of these catalysts. Mesoporous titania was synthesized following the evaporation-induced self-assembly (EISA) method with a subsequent treatment with ammonia to increase the thermal stability. As a result, the mesoporous titania obtained shows a high surface area (approximately 350 m2/g) and high stability. Vanadium oxide was deposited by the MDD method using a vanadyl acetylacetonate complex that was transformed into VOx after a controlled calcination in air flow at 300 degrees C. The mesostructure and porosity characteristics of titania remain even until the maximum V-loading was reached (0.4 mmol/g), as it was shown by N2 sorption measurements at -196 degrees C. The catalysts were characterized by chemical analysis, Fourier transform infrared-photoacoustic spectroscopy (FTIR-PAS), UV-vis diffuse reflectance (DR), and Fourier transform Raman spectroscopy. Raman spectra showed isolated V species for the different V-containing catalysts. Furthermore, UV-vis-DR revealed a higher contribution of polymeric species as the V loading increases. The VOx/mesoporous titania catalysts were highly active in the selective catalytic reduction of NOx. A high activity in the NO conversion was observed, which increases with increasing metal loading.     

Synthesis,characterization and evaluation of nanocrystalline anatase titania for the degradation of dibutyl phosphate

Degradation of dibutyl phosphate (DBP) in aqueous solution was successfully demonstrated in this paper using nanoparticles of anatase titania. Nanocrystalline anatase titania employed for the degradation study was synthesized in house by solgel route under stirring mode using titanium ethoxide precursor. The catalyst was characterized using XRD, DRS, BET, TEM, TG–DTA and Raman spectroscopy to establish the catalytic activity and surface morphology. A cylindrical photoreactor was used for the photocatalytic experiments. 10 mg of nano anatase titania and 0.5 mL of 30 % H₂O₂ were used as catalysts for the degradation of 1,000 mL of 240 mg/L DBP. Ion chromatographic procedure was used for following the DBP degradation. More than 95 % of DBP degradation could be in less than 45 min and the kinetics of DBP was found to follow pseudo first order. It was demonstrated that the photocatalytic efficiency of the synthesized titania was better than P-25 titania.     

Preparation of Titania Containing Mixed Oxides and Their Catalytic Activities

Titania containing catalysts were prepared by conventional procedures (coprecipitation, hydrogel kneading and titania precipitation) and a complexing-agent assisted sol-gel method. The effect of preparation methods on their properties and catalytic activities in the oxidation of olefins and decomposition of cumene hydroperoxide were examined. The sol-gel method gave the best dispersion of titania. In contrast, with the kneading and titania precipitation method, titania formed crystalline particles. The sol-gel catalysts are more effective for epoxydation of olefins because of the high dispersibility of Ti in them. However, the most active catalysts in the decomposition of cumene hydroperoxide are kneading ones.     

新型晶须状氧化钛担载Au的CO催化氧化性能

从钛钾比较高的二钛酸钾晶须出发,通过离子交换和热处理等步骤制备了具有不同微观结构的晶须状TiO2,然后通过均相沉积-沉淀法在制得的TiO2上担载1%的Au.采用X射线衍射、扫描电镜、低温N2吸附-脱附及透射电镜等技术对催化剂样品进行了表征,并测定了其催化CO氧化反应性能.结果表明,600℃处理所得晶须状TiO2载体(T(600))具有丰富的介孔结构,比表面积为59 m2/g,平均孔径为11 nm,担载Au后其孔道结构保持良好,而800℃处理所得晶须状TiO2样品(T(800))孔结构完全坍塌,但仍保持纯锐钛矿晶型.在相同担载条件下Au/T(800)上的Au颗粒尺寸明显小于Au/T(600)上的,但两者催化CO氧化反应活性相差不大,CO完全转化温度分别为80和70℃,活性均比Au/P25的高.     

Oxygen-deficient titania as alternative support for Pt catalysts for the oxygen reduction reaction

Insufficient electrochemical stability is a major challenge for carbon materials in oxygen reduction reaction （ORR） due to carbon corrosion and insufficient metal-support interactions. In this work, titania is explored as an alternative support for Pt catalysts. Oxygen deficient titania samples including TiO2-x and TiO2_xNy were obtained by thermal treatment of anatase TiO2 under flowing H2 and NH3, respectively. Pt nanoparticles were deposited on the titania by a modified ethylene glycol method. The samples were characterized by N2-physisorption, X-ray diffraction and X-ray photoelectron spectroscopy. The ORR activity and long-term stability of supported Pt catalysts were evaluated using linear sweep voltammetry and chronoamperometry in 0.1 mol/L HC104. Pt/TiO2_x and Pt/TiO2_xNy showed higher ORR activities than Pt/TiO2 as indicated by higher onset potentials. Oxygen deficiency in TiO2-x and TiO2-xNy contributed to the high ORR activity due to enhanced charge transfer, as disclosed by electrochemical impedance spectroscopy studies. Electrochemical stability studies revealed that Pt/TiOE_x exhibited a higher stability with a lower current decay rate than commercial Pt/C, which can be attributed to the stable oxide support and strong interaction between Pt nanoparticles and the oxygen-deficient TiO2-x support.     

Oxidation of CO on gold supported catalysts prepared by laser vaporization: direct evidence of support contribution

Gamma-Al2O3, ZrO2, and TiO2 gold supported model catalysts have been synthesized by laser vaporization. Structural characterization using Transmission Electron Microscopy and X-ray Photoelectron Spectroscopy experiments have shown that the gold clusters deposited on the different supports have similar distribution of size centered around 3 nm and are in the metallic state. However, X-ray photoemission measurements also indicate lower binding energies than the usual Au 4f(7/2) at 84.0 eV for both alumina and titania supported catalysts, indicating a modification of the electronic structure of the metal. One has taken benefit of these features to study the influence of the nature of the support toward CO oxidation activities without being hindered by particle size or gold oxidic species effects. By comparing the activities of the different catalysts, it is concluded that the nature of the support directly affects the activity of gold. The following tendency is observed: titania and zirconia are superior to alumina as supports, titania being slightly better than zirconia. From XPS and activity results we can conclude that the existence of negatively charged clusters is not the key point to explain the high activity observed for Au/ZrO2 and Au/TiO2 catalysts and also that metallic Au is the major catalytically active phase. Hence, due to their very nature, titania and to a less extent zirconia should participate to the catalytic process.     

Effects of the addition of titania on the thermal characterization of alumina-supported palladium

The detailed thermal characterization of Pd/TiO₂–Al₂O₃ catalysts under oxygen and hydrogen atmosphere was conducted by means of thermal gravimetric analysis/differential scanning calorimetry (TG/DSC), temperature-programmed reduction (TPR) and temperature-programmed desorption (TPD). A simultaneous TG/DSC measurement revealed that the heat evolved during oxygen adsorption at 25 °C varied slightly with the supports and had a higher value for the smaller palladium crystallite. Hydrogen chemisorption and BET measurements revealed that the coating of Pd/Al₂O₃ catalysts with titania modified the support character to achieve a high dispersion of palladium. TPR and TPD characterizations of oxidized samples further demonstrated that the coating of Pd/Al₂O₃ catalysts with titania promoted the reduction and decomposition of PdO into palladium.     

Influence of final calcination temperature and calcium addition on the properties of titania-based sulfur recovery catalysts

Compared to traditional alumina Claus catalysts, titania based sulfur recovery catalysts demonstrate improved initial activity for the recovery of elemental sulfur from both hydrogen sulfide and sulfur dioxide and are less prone to aging by sulfation. The influence of the preparation mode on the properties of titania catalysts is studied in detail: With increasing calcination temperature, surface area drastically decreases, whereas mechanical strength goes through a minimum, with only minor modifications of total pore volume and catalytic activity. Addition of calcium during catalyst preparation hinders the loss of mechanical properties while allowing a higher calcination temperature. Hydrothermal aging of such catalysts is therefore limited during operation in the plant.     

RHEOLOCY OF AQUEOUS DISPERSIONS OF ALUMINA,TITANIA AND MIXTURE OF ALUMINA AND TITANIA POWDERS

The electrophoretic mobility and rheology of alumina, titania and alumina / titania powder mixtures ( ratio of alumina : titania 1 : 2 and 2 : 1 ) were investigated in aqueous suspensions in the pH range 3 - 10. The results suggest that the electrophoretic mobility of the individual powders is independent of the particle concentration, but the electrokinetic behavior of the powder mixture depends upon the concentration of the individual constituents. The rheology of all the suspensions is charge related and while alumina and alumina / titania ( ratio 2 : 1 ) flocculate at pH 9.0 both titania and alumina / titania ( ratio 1 : 2 ) form low viscous dispersions. Similarly while later dispersions flocculate at pH 5.6, the former dispersions behave as Newtonian type fluids. Better correlation between the slip rheology and the electrokinetic behavior of suspensions containing both alumina and titania powders can be obtained provided the experimental results are evaluated based upon the total surface area of the individual powders but not the particle concentration.     

Temperature programmed desorption analysis of sol-gel-derived titania films

Sol-gel-derived titania films were analyzed by temperature programmed desorption (TPD) and X-ray diffraction (XRD) techniques. The relationship between the TPD curves measured for two types of titania gel films and their crystal structures was investigated. On the basis of the analyses, a preparation process for a titania sol solution containing anatase nanocrystals was designed and developed. Using this process, a colloidal anatase titania sol solution was prepared by heating aqueous titanium hydroxide containing HCl at 60°C for 2 h. The nanocrystal structure of the titania films obtained by coating the sol on glass substrates was confirmed by TPD and XRD measurements.     

Surface Hydroxyls and Chemisorbed Hydrogen on Titania and Titania Supported Cobalt

The dehydroxylation and rehydroxylation properties of titania (Degussa P-25) were investigated. FTIR and TPD-MS data indicate that hydroxyl groups are not completely removed at 500 °C in vacuo, and rehydration/rehydroxylation occur under helium (water content < 1 ppm) flow at room temperature. In addition, repeating dehydroxylation/rehydroxylation treatments for ten times does not significantly modify the dehydroxylation/rehydroxylation property of titania surface. Desorption of hydrogen from titania was observed at 535 °C after titania was reduced above 400 °C. The maximum surface density of hydrogen was determined to be 0.75 H atom/nm². TPD data show four types of hydrogen on 3% titania supported cobalt catalysts: hydrogen adsorbed on cobalt metal (desorption temperature around 100 °C), reverse spillover hydro gen (150-250 °C), hydrogen from H-TiO_2-x- Co interacting species (-330 °C), and recombined hydrogen from Ti³⁺-H on titania (-535 °C). The absence of hydrogen desorption peak at 535 °C for titania supported cobalt reduced above 400 °C can be explained in terms of the migration of H-TiO_2-x moieties onto cobalt metal surface during reduction. Removal of hydroxyl groups by thermal treatment before reduction enhanced the amount of hydrogen desorption from normal cobalt surface. This indicates that the hydroxyl groups play a role in the surface migration of H-Ti_2-x.     

WxC/SBA-16催化剂的制备、表征及催化加氢脱硫性能

以正硅酸乙酯为硅源, 仲钨酸铵为钨源, P123和F127为混合模板剂,采用水热晶化法一步合成了不同钨含量(以n(Si):n(W)表示)的WO3/SBA-16, 然后经甲烷/氢气(V(CH4)/V(H2)=1/4)混和气体程序升温还原碳化(TPC), 制备出了WxC/SBA-16(x=1, 2)催化剂. 采用XRD、N2-吸附/脱附、TEM和FTIR等分析测试技术对样品的结构进行了表征, 并以噻吩作为模型化合物, 对WxC/SBA-16催化剂的加氢脱硫催化活性进行了评价. 结果表明, 在一定钨含量的条件下, WO3/SBA-16和WxC/SBA-16样品仍然保持立方笼状介孔结构, 当n(Si):n(W)为30-10时, 碳化钨的物相为W2C; n(Si):n(W)为7.5时, 碳化钨的物相为W2C和WC. WxC/SBA-16催化剂表现出了良好的加氢脱硫催化性能.     

Hierarchical,Titania‐Coated,Carbon Nanofibrous Material Derived from a Natural Cellulosic Substance

Hierarchical, titania‐coated, nanofibrous, carbon hybrid materials were fabricated by employing natural cellulosic substances (commercial filter paper) as a scaffold and carbon precursor. Ultrathin titania films were firstly deposited by means of a surface sol–gel process to coat each nanofiber in the filter paper, and successive calcination treatment under nitrogen atmosphere yielded the titania–carbon composite possessing the hierarchical morphologies and structures of the initial paper. The ultrathin titania coating hindered the coalescence effect of the carbon species that formed during the carbonization process of cellulose, and the original cellulose nanofibers were converted into porous carbon nanofibers (diameters from tens to hundreds of nanometers, with 3–6 nm pores) that were coated with uniform anatase titania thin films (thickness ≈12 nm, composed of anatase nanocrystals with sizes of ≈4.5 nm). This titania‐coated, nanofibrous, carbon material possesses a specific surface area of 404 m² g^?1, which is two orders of magnitude higher than the titania–cellulose hybrid prepared by atomic layer deposition of titania on the cellulose fibers of filter paper. The photocatalytic activity of the titania–carbon composite was evaluated by the improved photodegradation efficiency of different dyes in aqueous solutions under high‐pressure, fluorescent mercury‐lamp irradiation, as well as the effective photoreduction performance of silver cations to silver nanoparticles with ultraviolet irradiation.     

Preparation of nearly monodisperse multiply coated submicrospheres with a high refractive index

Nearly monodisperse SiO2/TiO2/SiO2 multiply coated submicrospheres with nearly monodisperse silica submicrospheres as cores, thick titania layers, and thin silica skin were prepared to increase the refractive index of complex submicrospheres while keeping their near monodispersity and perfect surface properties. Nearly monodisperse colloidal silica submicrospheres as cores with a diameter of 200 nm were synthesized by a seeding technique on the basis of the hydrolysis of tetraethyl orthosilicate (TEOS) in an aqueous ethanol solution with ammonia as catalyst. On the basis of the hydrolysis of tetrabutyl orthotitanate, a procedure combining continuous feeding with multistep coating was determined to prepare titania coatings about 40 nm thick and increase the refractive index of the complex submicrospheres. The hydrolysis of TEOS was still used to get the outmost silica coating about 10 nm thick on titania coated silica submicrospheres to eliminate random aggregation caused by the TiO2 surface properties of the TiO2/SiO2 complex submicrospheres during the final fabrication of photonic crystals.     

V-P-O／TiO2-SiO2催化剂的制备、表征及其在丙烷氧化制取丙烯酸反应中的应用研究

通过湿磨法,将钒-磷-氧(V-P-O)氧化物负载于钛硅干凝胶(TiO_2-SiO_2)上,制备了V-P-O/TiO_2-SiO_2氧化物催化剂,并运用BET,XRD,TEM及XPS等技术考察了润湿剂,V-P-O的含量及焙烧条件对催化剂结构的影响.由BET方法发现,以异丁醇为润湿剂对催化剂表面积影响较小.XRD和TEM考察结果表明,所制备的催化剂有较高的热稳定性.通过XPS分析,证实钒元素主要以V(Ⅳ)价态存在于催化剂的表面.V-P-O/TiO_2-SiO_2催化剂在丙烷氧化反应中显示了良好的催化性能.     

Spectroscopic and structural characterization of chlorine loading effects on Mo/Si:Ti catalysts in oxidative dehydrogenation of ethane

The structural changes induced in a silica-titania mixed-oxide support (1:1 molar ratio) by chlorine addition at different loading levels, their relation to the structural characteristics of supported MoOx species over the support, and their correlation with ethane oxidative dehydrogenation (ODH) activity have been examined. The molybdenum and chlorine precursors are incorporated into the Si/Ti support network as it forms during gelation by using a "one-pot" modified sol-gel/coprecipitation technique. In situ X-ray diffraction during calcination shows the Si/Ti 1:1 mixed-oxide support is in a state of nanodispersed anatase titania over amorphous silica. With the addition of molybdenum and chlorine modifier, this anatase feature becomes more pronounced, indicating a decreased dispersion of titania. The effective titania surface area on the chlorine-doped Si:Ti support obtained from 2-propanol temperature-programmed reaction supports this observation. Raman spectra of dehydrated samples point to an enhanced interaction of MoOx species with silica at the expense of titania. X-ray photoelectron spectroscopic results show that, without forming a molybdenum chloride, the presence of chlorine significantly alters the relative surface concentration of Si vs Ti, the electronic structure of the surface MoOx species, and the oxygen environment around supported MoOx species in the Si/Ti network. Secondary ion mass spectrometry detected the existence of SiCl fragments from the mass spectra, which provides molecular insight into the location of chlorine in Mo/Si:Ti catalysts. The observed increase in ethane ODH selectivity with chlorine modification may be ascribed to the MoOx species sharing more complex ligands with silica and titania with the indirect participation of chlorine. Steady-state isotopic transient kinetic analysis (SSITKA) is used to to examine the oxygen insertion and exchange mechanisms. The catalysts show very little oxygen exchange with the gas phase in the absence of a reaction medium. During the steady-state ODH reaction, lattice oxygen appears to be the primary source of oxygen in the formation of water and CO2.