The preparation and performance of flocculent polyaniline/carbon nanotubes composite electrode material for supercapacitors

Polyaniline (PANI)/carbon nanotubes (CNTs) composite electrode material was prepared by in situ chemical polymerization. The structure and morphology of PANI/CNTs composite are characterized by Fourier infrared spectroscopy, scanning electron microscope, and transmission electron microscopy. It has been found that a flocculent PANI was uniformly deposited on the surface of CNTs. The supercapacitive behaviors of the PANI/CNTs composite materials are investigated with cyclic voltammetry, galvanostatic charge/discharge, impedance, and cycle life measurements. The results show that the PANI/CNTs composite electrodes have higher specific capacitances than CNT electrodes and better stability than the conducting polymers. The capacitance of PANI/CNTs composite electrode is as high as 837.6 F g⁻¹ measured by cyclic voltammetry at 1 mV s⁻¹. Besides, the capacitance retention of coin supercapacitors remained 68.0% after 3,000 cycles.     

Electrochemical performance of Co–Al layered double hydroxide nanosheets mixed with multiwall carbon nanotubes

Regular hexagonal Co–Al layered double hydroxides (Co–Al LDH) were synthesized by urea-induced homogeneous precipitation. This material proved to be nanosheets by scanning electron microscopy and X-ray diffraction measurements. The electrochemical capacitive behavior of the nanosheets in 1 M KOH solution were evaluated by constant current charge/discharge and cyclic voltammetric measurements, showing a large specific capacitance of 192 F·g⁻¹ even at the high current density of 2 A·g⁻¹. When multiwall carbon nanotubes (MWNTs) were mixed with the Co–Al LDH, it was found that the specific capacitance and long-life performance of all composite electrodes at high current density are superior to pure LDH electrode. When the added MWNTs content is 10 wt%, the specific capacitance increases to 342.4 F·g⁻¹ and remains at a value of 304 F·g⁻¹ until the 400th cycle at 2 A·g⁻¹, showing that this is a promising electrode material for supercapacitors working at heavy load. According to the electrochemical impedance spectra, MWNTs greatly increase the electronic conductivity between MWNTs and the surface of Co–Al LDH, which consequently facilitates the access of ions in the electrolyte and electrons to the electrode/electrolyte interface.     

Electropolymerized composite film of polypyrrole and functionalized multi-walled carbon nanotubes: effect of functionalization time on capacitive performance

The composite film of polypyrrole and functionalized multi-walled carbon nanotubes (PPy/F-MWNTs) was prepared by electropolymerization. MWNTs were functionalized by sonicating with a concentrated solution of H₂SO₄/HNO₃ (3/1, volume ratio) in a water bath for different times. The carbon nanotubes (CNTs) are cut into smaller portions with more functional groups introduced on their surface when the sonicating time (nominated as functionalization time hereafter) is increased. However, the specific capacitance of the composite film reaches a maximum of 240 F g⁻¹ at the scanning rate of 10 mV s⁻¹ when MWNTs are functionalized for 24 h, which is about 205 F g⁻¹, 225 F g⁻¹ and 232 F g⁻¹, respectively, when MWNTs are functionalized for 6 h, 12 h and 48 h. At a current load of 1.0 A g⁻¹, PPy/F-MWNT composite film functionalized for 24 h (PPy/F-MWNTs (24 h)) retains 93.49% of its initial capacitance after 1,000 cycles of galvanostatic charge/discharge, and the discharge efficiency is higher than 98.15% during cycling. High specific capacitance, good rate performance, fast charge/discharge ability and long cycling life are ascribed to the synergistic effect of the two components to form a porous composite film as well as the easy accessibility of counter ions into the film. Therefore, PPy/F-MWNT (24 h) composite film is a kind of promising electrode material for supercapacitors. The mechanism of underfunctionalization and overfunctionalization of carbon nanotubes is also discussed.     

Preparation and electrochemical performance of activated carbon thin films with polyethylene oxide-salt addition for electrochemical capacitor applications

The effect of polymer–salt addition in the activated carbon electrode for electric double-layer capacitor (EDLC) has been investigated. A series of composite thin film electrode consisting of activated carbon, carbon black, polytetrafluoroethylene and polymer–salt complex (polyethyleneoxide–LiClO₄) with an appropriate weight ratio were prepared and examined their performance for EDLCs using 1 mol L⁻¹ LiClO₄ in ethylene carbonate:diethylcarbonate electrolyte solution. The electrochemical capacitance performances of these electrodes with different compositions were characterized by cyclic voltammetry, galvanostatic charge–discharge cycling, and AC impedance measurements. By comparison, the best results were obtained with a composite electrode rich in polymer–salt additive (132 F g⁻¹ at 100 mA g⁻¹ of galvanostatic experiment). In general, the polymer–salt-containing electrode had shown improved performance over activated carbon electrodes without polymer–salt at high current density.     

Preparation and electrochemical properties of nanofiber poly(2,5-dihydroxyaniline)/activated carbon composite electrode for supercapacitor

In this study, poly(2,5-dihydroxyaniline) (PDHA) was successfully prepared by electrochemical method on the surface of active carbon (AC) electrodes. The physical and electrochemistry properties of PDHA/AC composite electrode compared with pure AC electrode were investigated by scanning electronic microscope (SEM), cyclic voltammetry (CV), electrochemical impedance spectroscopy, cycle life test. From SEM, PDHA presents nanofiber network morphology. The diameter of the nanofiber PDHA is about 200–300 nm. PDHA/AC composite electrode shows redox peaks in CV curve and voltage plateaus in galvanostatic charge–discharge curve, and all these indicate that PDHA/AC composite electrode has more advantages. The maintenance of the capacitance compared to initial cycle capacitance of composite electrode is about 90% during the charge–discharge cycles. In conclusion, The PDHA/AC composite electrode shows much higher specific capacitance (958 F g⁻¹), better power characteristics, longer cycle life. Therefore, PDHA/AC composite electrodes were more promising for application in capacitor. This can be attributed to the introduction of nanofiber PDHA. The effect and role of PDHA in the composite electrodes were also discussed in detail.     

Preparation and performances of carbon aerogel microspheres for the application of supercapacitor

Carbon aerogel (CA) microspheres were successfully synthesized by an inverse emulsion polymerization routine. Morphology and physical properties of the CA microspheres were characterized by scanning electron microscopy, N₂ sorption isotherm, and transmission electron microscopy. The results showed that the CA microspheres were all fine spheres with diameters about 4 μm, and the CA microsphere was a typical mesoporous material with ordered mesoporous nano-network structure. The maximum capacitance of the electrode obtained from cyclic voltammetry was 187.08 F/g and the capacitance of the supercapacitor resulted from galvanostatic charge–discharge tests was up to 45.98 F/g. The supercapacitor using CA microsphere as electrode material presented a long cycle life, high charge–discharge efficiency, and low R _s of 0.70 Ω in 6 M KOH electrolyte.     

Platelike CoO/carbon nanofiber composite electrode with improved electrochemical performance for lithium ion batteries

Platelike CoO/carbon nanofiber (CNF) composite materials with porous structures are synthesized from the thermal decomposition and recrystallization of β-Co(OH)₂/CNF precursor without the need for a template or structure-directing agent. As negative electrode materials for lithium-ion batteries, the platelike CoO/CNF composite delivers a high reversible capacity of 700 mAh g⁻¹ for a life extending over hundreds of cycles at a constant current density of 200 mA g⁻¹. More importantly, the composite electrode shows significantly improved rate capability and electrochemical reversibility. Even at a current of 2 C, the platelike CoO/CNF composite maintain a capacity of 580 mAh g⁻¹ after 50 discharge/charge cycles. The improved cycling stability and rate capability of the CoO/CNF composite electrodes may be attributed to synergistic effect of the porous structural stability and improved conductivity through CNF connection.     

碳纳米管/聚苯胺/石墨烯复合纳米碳纸及其电化学电容行为

通过真空抽滤的方法制备碳纳米管纸,并对其进行循环伏安电化学氧化处理.以该电化学氧化处理的碳纳米管(CV-CNT)纸为基体,采用电化学聚合沉积聚苯胺(PANI),随后吸附石墨烯(GR),制备具有三明治夹心结构的碳纳米管/聚苯胺/石墨烯(CV-CNT/PANI/GR)复合纳米碳纸.该结构外层为GR,内层由PANI包裹的CNT形成网络骨架,充分发挥三者各自优势构建柔性电极材料.用场发射扫描电镜(FE-SEM)、透射电子显微镜(TEM)、拉曼光谱对其形貌与结构进行表征,并测试其电化学性能.研究发现:PANI呈纳米晶须状,并均匀包裹在CV-CNT表面;该复合碳纸具有良好的电容特性、大电流充放电特性以及良好的循环稳定性能.电流密度为0.5A·g-1时,比电容可达415F·g-1;20A·g-1时仍能保持106F·g-1的比电容.由于GR的保护作用,1000次循环之后较CV-CNT/PANI保持更高的有效比电容.该CV-CNT/PANI/GR复合碳纸展现出在高性能超级电容器柔性电极材料的潜在应用价值.     

Facile synthesis of polyaniline/TiO2/graphene oxide composite for high performance supercapacitors

The polyaniline/TiO₂/graphene oxide (PANI/TiO₂/GO) composite, as a novel supercapacitor material, is synthesized by in situ hydrolyzation of tetrabutyl titanate and polymerization of aniline monomer in the presence of graphene oxide. The morphology, composition and structure of the composites as-obtained are characterized by SEM, TEM, XRD and TGA. The electrochemical property and impedance of the composites are studied by cyclic voltammetry and Nyquist plot, respectively. The results show that the introduction of the GO and TiO₂ enhanced the electrode conductivity and stability, and then improved the supercapacitive behavior of PANI/TiO₂/GO composite. Significantly, the electrochemical measurement results show that the PANI/TiO₂/GO composite has a high specific capacitance (1020 F g⁻¹ at 2 mV s⁻¹, 430 F g⁻¹ at 1 A g⁻¹) and long cycle life (over 1000 times).     

Composite films of polyaniline and molybdenum oxide formed by electrocodeposition in aqueous media

Composite films of polyaniline (PANI) and molybdenum oxide (MoO_x) were afforded through a convenient route of electrocodeposition from aniline and (NH₄)₆Mo₇O₂₄. The composite films showed characteristic redox behaviors of PANI and MoO_x, respectively, on the cyclic voltammograms. Chlorate and bromate were catalytically electroreduced with an enlarged current on the composite film at a potential ca. 0.2 V more positive than that on MoO_x. The potential window for the composite film to display pseudocapacitive properties in 1.0 mol·dm⁻³ NaNO₃ was −0.6 ∼ 0.6 V vs SCE. The cathodic potential limit shifted at least 0.4 V negatively from that of polyaniline (PANI)-based materials reported so far. The specific capacitance was 363.6 F·g⁻¹ when the composite film was charged–discharged at 1.5 mA·cm⁻², about two times of that of the similarly prepared PANI. The composite film was characterized by Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Molybdenum existed in a mixed state of +5 and +6 in the composite film based on XRD and XPS investigations. Figure PANI and (MoO_x) were electrocodeposited in aqueous solutions from aniline and (NH₄)₆Mo₇O₂₄. The composite film obtained displayed catalytic activities toward the electroreduction of oxoanions. The pseudocapacitance of the composite film is nearly two times of that of PANI with the potential window extended negatively up to −0.6 V vs SCE     

Preparation of 3D MnO2/Polyaniline/Graphene Hybrid Material via Interfacial Polymerization as High‐Performance Supercapacitor Electrode

MnO₂/polyaniline/graphene composite as a supercapacitor electrode material was synthesized through an interfacial polymerization approach in the interface of oil/water phase. The as‐synthesized MPG is characterized by infrared spectroscopy, XRD, XPS, SEM and TEM, and its electrochemical performance is measured by cyclic voltammetry, galvanostatic charge/discharge, and electrochemical impedance spectroscopy. The 3D nanostructure of MPG and loose nanorod structure of polyaniline (PANI) coated with round MnO₂ pellets could be clearly observed. The maximum energy density of MPG is 45.4 Wh/kg (at a power density of 67.8 kW/kg) and the highest power density is 229.2 kW/kg (at an energy density of 25.7 Wh/kg). The capacitance retentions after 500 cycles at the scan rate of 5 mV/s for MGP composite and PANI/graphene are 70.4% and 59.1%, respectively, and the capacitance values after 500 cycles are 158.4 F/g and 114.8 F/g, respectively. The improved performance of MPG is due to the 3D nanostructure, loose nanorod structure of PANI and stable support of graphene, which prevent the mechanical deformation effectively during the fast charge/discharge process and facilitate the diffusion of the electrolyte ions into the inner region of active materials. The composite material is very promising for the next generation of high‐performance supercapacitors electrode.     

Tube-covering-tube nanostructured polyaniline/carbon nanotube array composite electrode with high capacitance and superior rate performance as well as good cycling stability

The combination of a vertically aligned carbon nanotube array (CNTA) framework and electrodeposition technique leads to a tube-covering-tube nanostructured polyaniline (PANI)/CNTA composite electrode with hierarchical porous structure, large surface area, and superior conductivity. PANI/CNTA composite electrode has high specific capacitance (1030 F g⁻¹), superior rate capability (95% capacity retention at 118 A g⁻¹), and high stability (5.5% capacity loss after 5000 cycles). Energy storage characteristics of the PANI/CNTA composite are presented in this paper.     

超级电容器用含氮碳与含氮碳/炭气凝胶复合电极材料的制备和性能研究

采用原位聚合法合成聚苯胺(PAIN)及聚苯胺/炭气凝胶(PAIN/CA)复合材料,经过高温裂解制备含氮碳(NC)及含氮碳/炭气凝胶复合材料(NC/CA),再以KOH为活化剂对其进行活化,制备活化含氮碳(ANC)及活化含氮碳/炭气凝胶复合材料(ANC/CA)。采用扫描电镜、循环伏安、恒流充放电以及电化学阻抗等方法进行性能测试,结果表明,由于KOH的活化作用,含氮碳材料的粒径明显变小,其比电容值为138 F/g,高于未活化含氮碳材料(98 F/g),ANC/AC3复合材料电极的比电容值比ACA电极(88 F/g)高,达到127 F/g。     

An Advanced NiCoFeO/Polyaniline Composite for High‐Performance Supercapacitors

To reduce the charge‐transfer resistance of supercapacitors and achieve faster reversible redox reactions, ternary Ni‐Co‐Fe layered double hydroxide was prepared by using the urea method and then calcined to give NiCoFe oxide (NiCoFeO). To enhance conductivity, a polyaniline (PANI) conductive layer was assembled on the surface of the NiCoFeO particles by in situ oxidative polymerization of aniline monomers. The as‐prepared NiCoFeO/PANI composite was successful employed as a supercapacitor electrode. It was found that the NiCoFeO/PANI composite displayed good cycling stability, with a capacity loss of only 29.54 % after 5000 cycles. Furthermore, the NiCoFeO/PANI composite also exhibited excellent supercapacitor performance, with a high specific capacity of 843 F g^?1 at a current density of 2 A g^?1, whereas NiCoFeO showed a specific capacity of only 478 F g^?1. This result was attributed to the synergistic effect between NiCoFeO and PANI. The facile synthesis strategy and excellent electrochemical performance suggest that NiCoFeO/PANI is a promising economical electrode material for applications in supercapacitors.     

Graphene oxide doped polyaniline for supercapacitors

A novel high-performance electrode material based on fibrillar polyaniline (PANI) doped with graphene oxide sheets was synthesized via in situ polymerization of monomer in the presence of graphene oxide, with a high conductivity of 10 S cm^?1 at 22 °C for the obtained nanocomposite with a mass ratio of aniline/graphite oxide, 100:1. Its high specific capacitance of 531 F/g was obtained in the potential range from 0 to 0.45 V at 200 mA/g by charge–discharge analysis compared to 216 F/g of individual PANI. The doping and the ratio of graphene oxide have a pronounced effect on the electrochemical capacitance performance of the nanocomposites.     

Fabrication of Polyaniline/Graphene/Polyester Textile Electrode Materials for Flexible Supercapacitors with High Capacitance and Cycling Stability

Vertical polyaniline (PANI) nanowire arrays on graphene‐sheet‐coated polyester cloth (RGO/PETC) were fabricated by the in situ chemical polymerization of aniline. The 3D conductive network that was formed by the graphene sheets greatly enhanced the conductivity of PANI/RGO/PETC and improved its mechanical stability. PANI nanowire arrays increased the active surface area of PANI, whilst the hierarchically porous structure of the PANI/RGO/PETC electrode facilitated the diffusion of the electrolyte ions. Electrochemical measurements showed that the composite electrode exhibited a maximum specific capacitance of 1293 F g^?1 at a current density of 1 A g^?1. Capacitance retention was greater than 95 %, even after 3000 cycles, which indicated that the electrode material has excellent cycling stability. Moreover, the electrode structure endowed the PANI/RGO/PETC electrode with a stable electrochemical performance under mechanical bending and stretching.     

Preparation and electrochemical performance of nano-structured Li<Subscript>2</Subscript>Mn<Subscript>4</Subscript>O<Subscript>9</Subscript> for supercapacitor

Nano-structured spinel Li₂Mn₄O₉ powder was prepared via a combustion method with hydrated lithium acetate (LiAc·2H₂O), manganese acetate (MnAc₂·4H₂O), and oxalic acid (C₂H₂O₄·2H₂O) as raw materials, followed by calcination of the precursor at 300 °C. The sample was characterized by X-ray diffraction, scanning electron microscope, and energy-dispersive X-ray spectroscopy techniques. Electrochemical performance of the nano-Li₂Mn₄O₉ material was studied using cyclic voltammetry, ac impedance, and galvanostatic charge/discharge methods in 2 mol L⁻¹ LiNO₃ aqueous electrolyte. The results indicated that the nano-Li₂Mn₄O₉ material exhibited excellent electrochemical performance in terms of specific capacity, cycle life, and charge/discharge stability, as evidenced by the charge/discharge results. For example, specific capacitance of the single Li₂Mn₄O₉ electrode reached 407 F g⁻¹ at the scan rates of 5 mV s⁻¹. The capacitor, which is composed of activated carbon negative electrode and Li₂Mn₄O₉ positive electrode, also exhibits an excellent cycling performance in potential range of 0–1.6 V and keeps over 98% of the maximum capacitance even after 4,000 cycles.     

Preparation of activated carbon from polyaniline by zinc chloride activation as supercapacitor electrodes

Activated carbon for supercapacitor electrode was prepared from polyaniline using chemical activation with ZnCl₂. The morphology, surface chemical composition, and surface area of the as-prepared carbon materials were investigated by scanning electron microscope, atomic force microscopy, X-ray photoelectron spectroscopy, and Brunauer–Emmett–Teller measurement, respectively. Electrochemical characteristics were evaluated by cyclic voltammograms, galvanostatic charge/discharge, and electrochemical impedance spectroscopy tests in 6.0?mol?L^?? KOH aqueous solution. The electrochemical measurements showed that ZnCl₂ activation led to better capacitive performances. The activated carbon presented a high-specific gravimetric capacitance of 174?F?g^??, with rectangular cyclic voltammetry curves at a scan rate of 2?mV?s^??, and it remained 93% even at a high scan rate of 50?mV?s^??. These demonstrated that activated carbon would be a promising electrode material for supercapacitors.     

Influence of addition of cobalt oxide on microstructure and electrochemical capacitive performance of nickel oxide

Ni–Co oxide nanocomposite was prepared by thermal decomposition of the precursor obtained via a new method—coordination homogeneous coprecipitation method. The synthesized sample was characterized physically by X-ray diffraction, scanning electron microcopy, energy dispersive spectrum, transmission electron microscope, and Brunauer–Emmett–Teller surface area measurement, respectively. Electrochemical characterization of Ni–Co oxide electrode was examined by cyclic voltammetry, galvanostatic charge–discharge, and electrochemical impedance measurements in 6-mol L⁻¹ KOH aqueous solution electrolyte. The results indicated that the addition of cobalt oxide not only changed the morphology of NiO but also enhance its electrochemical capacitance value. A specific capacitance value of 306 F g⁻¹ of Ni–Co oxide nanocomposite with n _Co = 0.5 (n _Co is the mole fraction of Co with respect to the sum of Co and Ni) was measured at the current density of 0.2 A g⁻¹, nearly 1.5 times greater than that of pure NiO electrode. Lower resistance and better rate capability can also be observed.     

Study of capacitive properties in supercapacitor for copolymer of aniline with m-phenylenediamine

The copolymers were synthesized with different molar ratios of m-phenylenediamine to aniline (R for short) by a chemical oxidation method. The products were first used as electrochemical activity materials of the supercapacitor. Capacitive behaviors of the prepared copolymers in 1 mol·L⁻¹ H₂SO₄ electrolyte were examined by electrochemical impedance spectroscopy, cyclic voltammeter, and galvanostatic charge/discharge. The relationship of molar ratios with capacitive property of the prepared products was investigated too. The results showed that the product with R of 2:98 displayed better electrochemical properties than that of the other products. Compared with the synthesized polymer in the absence of m-phenylenediamine, the polymerized copolymer with R of 2:98 exhibited the initial specific capacitance value of 475 F·g⁻¹, which increased by nearly 10.1% than that of the former at a current density of 200 mA·g⁻¹ in 1 mol·L⁻¹ H₂SO₄ electrolyte in the potential range of −0.3 to 0.7 V. The discharge specific capacitance value of the copolymer remained 300 F·g⁻¹ after 1,000 cycles, exhibiting a good cycling performance and the structure stability.