Extraction and spectrophotometric determination of molybdenum(VI) with Malachite Green and p-chloromandelic acid

Molybdenum(VI) reacts with p-chloromandelic acid to form a complex extractable into chlorobenzene with Malachite Green, from aqueous solution at pH 2.0-4.0 at room temperature, and can then be determined indirectly by measuring the absorbance of the Malachite Green in the extract, at 630 nm. The calibation graph is linear for molybdenum over the range 0.26-10.0 x 10(-6)M (0.10-4.0 mug); the apparent molar absorptivity is 1.06 x 10(5) l.mole(-1).cm(-1). The method has been applied to the determination of molybdenum in mild steels with satisfactory results.     

Extraction-spectrophotometric determination of germanium(IV) with mandelic acid and malachite green

A method has been developed for determination of germanium, based on complexation with mandelic acid and extraction of the ion-associate formed with Malachite Green (MG) into chlorobenzene. A weakly acidic aqueous solution (pH 2.5-3.5) at room temperature is used and indirect determination is achieved by measuring the absorbance of MG in the extract, at 628 mn. The calibration graph is linear over the range (0.17-8.63) x 10(-6) (0.05-2.50 mug of germanium); the apparent molar absorptivity is 1.33 x 10(5) 1.mole(-1).cm(-1). The interferences from Fe, Ti, Sn(IV), Mo, and SB(III) can be eliminated by addition of trans-1,2-diaminocyclohexanetetra-acetic acid and sodium diethyldithiocarbamate.     

Screening and confirmation of triphenylmethane dyes and their leuco metabolites in trout muscle using HPLC-vis and ESP-LC-MS.

An extraction and clean-up protocol for the determination of Malachite Green and Crystal Violet and the corresponding leuco compounds in trout muscle has been developed. Final determination is by HPLC with visible (screening) or ESP-MS (confirmation) detection. In both cases lead(IV) oxide was used on-line to oxidise the leuco compounds back to the parent after chromatographic separation and prior to detection. The procedure was validated down to 2 micrograms kg-1. Intra- and inter-batch precision was measured at 3 levels for all compounds. Recoveries were in the range 66-116% with RSD of 1-17% for determination by HPLC with visible detection. For LC-MS determination, recoveries were in the range 61-94% with RSD of 4-15%. Limited surveillance data indicated that Malachite Green usage was more effectively monitored by including the leuco compound as well as the parent (9 positives for the leuco compound as opposed to 1 for Malachite Green out of 31 samples analysed).     

Extraction-spectrophotometric determination of boron and antimony in carbon and low-alloy steels with mandelic acid and malachite green

A very simple and sensitive extraction method using mandelic acid and Malachite Green has been applied to the determination of boron and antimony in steels (carbon and low-alloy). When chlorobenzene is used as the solvent, boron and antimony are simultaneously extracted as ion-pairs of their mandelates with Malachite Green from weak acidic media, but only the boron compound is extracted in the presence of tartrate. Antimony is determined from the difference in absorbance of the extracts. In the case of benzene, boron alone was extracted and determined. Large amounts of iron(II) and other metal cations do not interfere, so the steel samples are dissolved in dilute sulphuric acid. Very low boron (0.0009-0.0091%) and antimony (0.002-0.02%) contents in steel are easily determined without any pretreatment.     

Non-aqueous cerimetric determination of phenylhydrazides

A non-aqueous oxidimetric method is described for the determination of some carboxylic acid phenylhydrazides with ammonium hexanitratocerate(IV) in acetonitrile. The end-points have been detected visually with chemical indicators (diphenylamine, diphenylbenzidine, Methyl Red, Malachite Green, Janus Green, Gentian Violet) and potentiometrically. The compounds are smoothly, rapidly and quantitatively oxidized with a two-electron change per hydrazino group. The method is simple, accurate, reliable and widely applicable.     

A novel and highly sensitive catalytic method with oscillopolarographic detection for the determination of ultratrace amounts of iridium

Iridium(IV) has a strong catalytic effect on the slow redox reaction between Malachite Green and periodate ion in pH 4.2 acetate buffer solution at 100 degrees , and Malachite Green exhibits a sensitive single-sweep oscillopolarographic wave at -0.65 V vs. SCE. This provides the basis for a novel and highly sensitive and selective catalytic method with oscillopolarographic detection for iridium. The effect of pH, potassium periodate and Malachite Green concentrations, reaction temperature and reaction time and other variables are investigated. The detection limit is 8 ng/l. with a fixed-reaction time of 10 min. A linear calibration graph from 24 to 1600 ng/l. is obtained. Possible interferences by co-existing ions are examined.     

Study of the titanium-phenylfluorone complex formed in the presence of Triton X-305 and emulsifier OP

A highly sensitive method for the spectrophotometric determination of titanium with phenylfluorone (PF) in the presence of Triton X-305 and emulsifier OP has been developed. In acid medium (pH 1.4-2.2) Ti(IV) forms red-violet complexes with PF, Triton X-305 and OP. The complex exhibits maximum absorption at 540 nm. The molar absorptivity is 1.63 x 10(5) 1.mole(-1).cm(-1). The Ti:PF ratio in the complex is 1:2. Beer's law is obeyed in the titanium concentration range 0-0.2 microg/ml in the final solution. Fluoride and EDTA interfere. The method has been used for the rapid direct determination of microamounts of Ti(IV) in soils and cereals with satisfactory results.     

Extractive spectrophotometric determination of uranium with Malachite Green

A sensitive spectrophotometric method based on the extraction of a uranium-benzoate-Malachite Green complex by chlorobenzene is described. The absorption maximum is at 635 nm and the molar absorptivity is 8.3 x 10(4) 1 mole(-1), cm(-1). A preliminary separation of uranium by extraction with methyl isobutyl ketone from acid-deficient aluminium nitrate solution is used to avoid interferences. An aliquot of the extract is then diluted with chlorobenzene and shaken with benzoate buffer containing Malachite Green (MG). The method has been applied for the determination of uranium in a synthetic leach solution. The complex extracted is probably [MG(2)(C(6)H(5)COO)(3)][MG(+)].     

Extraction and spectrophotometric determination of titanium(IV) with alizarin and fluoride

The characteristics of the mixed-ligand titanium(IV)-fluoride-alizarin complex, including the optimum conditions of formation and extraction into methyl isobutyl ketone, are described. A simple and sensitive procedure for spectrophotometric determination of titanium has been developed. At pH 9.5-10.3 titanium reacts with alizarin in the presence of fluoride to form a red-violet complex that is completely extractable into methyl isobutyl ketone, and has its absorption maximum at 513 nm. The molar absorptivity at 513 nm is 7.0 x 10(4)l.mole(-1).cm(-1). Beer's law is obeyed up to 22 mug of titanium in 30 ml of solution. The method has been used for the determination of titanium in an oxide mixture and aluminium alloy samples.     

Synergic extraction and spectrophotometric determination of titanium(IV)

A method has been developed for the synergic extraction and spectrophotometric determination of Ti(IV) with N-hydroxy-NN'-diphenylbenzamidine and thiocyanate. The yellow ternary complex, extracted into chloroform from dilute sulphuric acid medium (pH = 1.5+/-0.1), has maximum absorbance at 390 nm (molar absorptivity 1.3 x 1O(4) 1.mole(-1). cm(-1)). The method is free from interference from a large number of foreign ions and is recommended for the determination of titanium in steel.     

Solvent extraction-spectrophotometric determination of phosphate with molybdate and malachite green in river water and sea-water

Molybdophosphate, formed between orthophosphate and molybdate in sulphuric acid solution, is extracted into a mixture of toluene and 4-methylpentan-2-one (1:3 v v ) with Malachite Green as counter-ion. A single extraction with equal phase volumes gives an apparent molar absorptivity for phosphate of 2.3 x 10(5) l.mole(-1).cm(-1) at 630 nm; the absorbance of the reagent blank is 0.03. With an organic to aqueous phase-volume ratio of 1:10, the molar absorptivity is 2.5 x 10(5) l.mole(-1).cm(-1) and the absorbance of the reagent blank 0.08. By the proposed method, ng ml levels of phosphorus can be determined, and the detection limit is about 0.1 ng ml . The standard deviation and relative standard deviation for the determination of phosphorus in tap water (4.3 ng ml ) are 0.05 ng ml and 1.1%, respectively. The method can also be applied to the determination of phosphorus in river water and sea-water.     

A highly sensitive spectrophotometric method for determination of micro amounts of arsenic

A highly sensitive spectrophotometric method for determination of arsenic, based on the formation of an ion-association complex between arsenoantimonomolybdenum blue and Malachite Green, has been developed. The ion-association complex is soluble in the presence of Triton X-305, so arsenic can be determined directly in aqueous solution. The apparent molar absorptivity for arsenic is 1.13 x 10(5) l.mole(-1).cm(-1) at 640 nm. Beer's law is obeyed for 0-5 mug of arsenic. The lower limit of determination (absorbance = 0.01) is 4 ng ml in the final solution.     

Photometrische Bestimmung kleiner Phosphatmengen mit Malachitgrün

In the presence of a stabilising colloid Malachite Green and phosphododekamolybdate acid form a dyestuff salt. When the excess of the Malachite Green has reacted in acid solution to colourless products, the remaining colour is a measure for the phosphate quantity. The method permits the determination of 10–1200 μg of phosphate/l.     

Rapid, selective, direct and derivative spectrophotometric determination of titanium with 2,4-dihydroxybenzaldehyde isonicotinoyl hydrazone

A simple and sensitive spectrophotometric method is developed for the determination of titanium in aqueous medium. The metal ion forms a reddish brown coloured complex with 2,4-dihydroxybenzaldehyde isonicotinoyl hydrazone (2,4-DHBINH) in the pH range 1-7. The complex shows two absorption maxima, one at 430 nm and the other at 500 nm. The reagent shows appreciable absorbance of 430 nm and negligible absorbance at 500 nm at pH 1.5. Beer's law is obeyed in the range 0.09 to 2.15 mug ml(-1) of titanium(IV). The molar absorptivity and the Sandell's sensitivity of the method are 1.35 x 10(4) 1 mol(-1) cm(-1) and 0.0049 mug cm(-2), respectively. A method for the determination of titanium by first-order derivative spectrophotometry is also proposed. The methods have been employed successfully for the determination of titanium in several alloy and steel samples.     

Anodic stripping voltammetric determination of titanium(IV) using a carbon paste electrode modified with cetyltrimethylammonium bromide

A method is described for the voltammetric determination of titanium(IV) using a carbon paste electrode modified in situ with cetyltrimethylammonium bromide. The cationic micellar surfactant adsorbs onto the electrode particularly at negative potentials, simultaneously preconcentrating titanium(IV) as the oxalate complex with reduction to titanium(III). Anodic stripping voltammetry exploiting reoxidation can be used for the determination of trace levels of titanium(IV). Linearity between current and concentration exists between 5 and 160 mug l(-1) Ti(IV) (preconcentration time 2 min). The limit of detection (calculated as 3sigma) is 0.1 mug l(-1), with a preconcentration time of 10 min.     

Differential determination of antimony(III) and antimony(V) by solvent extraction-spectrophotometry with mandelic acid and Malachite Green, based on the difference in reaction rates

Highly sensitive and reproducible extraction-spectrophotometric methods for differential determination of antimony(III) and antimony(V) were investigated. It was found that antimony(III) reacts easily with mandelic acid to form a complex anion extractable into chlorobenzene with Malachite Green from weakly acidic media (pH 2.2-3.5) at room temperature, whereas antimony(V) reacts only slowly, and heating for 15 min at 45 degrees is needed to obtain maximum sensitivity. The significant difference between the rates of reaction of mandelic acid with antimony(III) and antimony(V) was applied to the differential determination of these two species. The calibration graph was linear over the range 0.15-6.0 mug for antimony(III), and 0.20-10 mug for antimony(V).     

Rapid spectrophotometric method (aqueous and extractive) for the determination of titanium in silicate rocks

A sensitive and highly selective aqueous as well as extractive spectrophotometric method has been developed for the determination of titanium(IV) using 2,3-dihydroxynaphthalene (H(2)ND) as a chromogenic agent. The reagent (H(2)ND) forms a 1:3 (TiOH(3+):ligand) complex at pH 4-9. The molar absorptivity and Sandell's sensitivity are 3.2 x 10(4) l . mol(-1)mol . cm(-1) and 0.001 microg/cm(2), respectively at lambda(max) 375 nm. The method has been found highly selective for Ti(IV) determination in rock samples. Solvent extraction of Ti(IV) in ethylacetate greatly improves the detection limit of the method. The method has been successfully applied to diverse silicate rock samples and results obtained are favourably comparable with those obtained from the tiron method. The reagent (H(2)ND) used in the present investigation is a much better variant than tiron for titanium(IV) determination in silicate rock samples in terms of sensitivity, selectivity, operational simplicity and economy.     

Fabrics and papers modified with analytical reagents for the test determination of selenium(IV) and tellurium(IV)

It is shown that Malachite Green and Crystal Violet immobilized on viscose fabrics can be used as reagents for the rapid determination of selenium(IV) and tellurium(IV). Selenium is determine by the color intensity of ion associates formed by the reagents with the triiodide ion formed upon the reduction of selenium(IV) with potassium iodide and tellurium, by the color intensity of reagent ion associates with telluromolybdic heteropoly acid. The analytical ranges for selenium and tellurium(IV) were 0.005–0.5 and 0.01–0.1 mg/L upon passing 20 and 100 mL of a test solution through the indicator matrix, respectively. The duration of analysis does not exceed 15–20 min. The relative standard deviation is 50%. Test strips were proposed for determining 0.1–100 mg/L selenium(IV) and 1–1000 mg/L tellurium(IV) by the length of the colored zone. The determination of selenium(IV) is based on the oxidation of 4-nitrophenylgydrazine to its diazonium salt and salt interaction with naphthylamine chemically immobilized on paper with the formation of a red azo compound. The determination of tellurium(IV) is based on its reaction with Bismuthol II immobilized on a paper.     

Determination of trace titanium with titanium(IV)-(DBC-arsenazo)-potassium bromate system by catalytic-kinetic spectrophotometry

In a 0.080 M sulphuric acid medium, trace titanium(IV) catalyzes the discoloring reaction of DBC-arsenazo oxidized by potassium bromate and the discoloring degree is proportional to the concentration of titanium(IV) in the solution. A new catalytic-kinetic spectrophotometric method for the determination of trace titanium(IV) was developed based on this principle. At a wavelength of 516 nm, the linear range of determination of titanium(IV) is 0–2.2 μg/25 mL. The detection limit for the determination of titanium is 2.04 ng/mL. The present method has been satisfactorily applied to the determination of titanium in fish samples. The text was submitted by the authors in English.     

Spectrophotometric determination of titanium with N-m-Tolyl-N-phenylhydroxylamine and its application to environmental samples

N-m-Tolyl-n-phenylhydroxylamine is proposed for the spectrophotometric determination of titanium. The reagent forms a yellow chloroform-soluble complex with titanium in media with a hydrochloric acid concentration of at least 9M. The apparent molar absorptivity at 380 nm is 7.4 x 10(3) 1.mole(-1).cm(-1). The optimum final concentration range is 0-54 mug of titanium in 10 ml of chloroform. The complex contains the metal and reagent in 1:2 ratio. The proposed method has been successfully applied to the determination of titanium in coal, coal fly-ash, pond sediment and asphalt.