Application of Voltammetric Method of Total Chromium Determination in the Presence of Cupferron for Selective Determination of Cr(VI) in Water Samples

A voltammetric method of Cr(VI) determination in a flow system based on the combination of selective accumulation of the product of Cr(VI) reduction on hanging mercury drop electrode and a very sensitive method of chromium determination in the presence of cupferron previously described is proposed. The calibration graphs were linear from 3 × 10⁻⁹ to 3 × 10⁻⁸ and from 5 × 10⁻¹⁰ to 5 × 10⁻⁹ mol L⁻¹ for accumulation times of 120 and 600 s, respectively. The detection limit for the accumulation time of 600 s was 9 × 10⁻¹¹ mol L⁻¹. The relative standard deviation was 5.1% (n = 5) for Cr(VI) concentration 1 × 10⁻⁸ mol L⁻¹ and the accumulation time of 120 s. The influence of foreign ions commonly present in water samples is presented. The validation of the method was made by studying the recovery of Cr(VI) from spiked natural water samples.     

Indirect kinetic microdetermination of oxalate, citrate, and fluoride ions

An indirect catalytic method for the separate microdetermination of oxalate, citrate, and fluoride ions is described. The method is based on the inhibition action of oxalate, citrate, and fluoride ions on the catalytic oxidation reaction of 2,4-diaminophenol-hydrogen peroxide by iron(III).Procedures for the determination of 1.76 × 10⁻² to 17.6 × 10⁻² μg/ml for oxalate ion, 3.78 × 10⁻² to 30.24 × 10⁻² μg/ml for citrate ion, and 0.38 to 4.18 μg/ml for fluoride ion are given.Quantities of 1.76 × 10⁻² to 17.6 × 10⁻² μg/ml for oxalate ion, 3.78 × 10⁻² to 30.24 × 10⁻² μg/ml for citrate ion, and 0.38 to 4.18 μg/ml for fluoride ion could be determinated with a relative error of about 1–3.5% for oxalate and citrate ions and 1–2% for fluoride ion.     

Catalytic microdetermination of iron

A reaction rate method is described for the microdetermination of iron. The method is based on the catalytic action of iron on the reaction of 2,4-diaminophenol with hydrogen peroxide. The effect of reagent concentration is studied and the maximum tolerable amounts of interfering ions are determined. Procedures for the determination of 2.8 × 10⁻³ to 2.8 × 10⁻² μg/ml are given.Quantities of 2.8 × 10⁻³ to 2.8 × 10⁻² μg/ml could be determinated with a relative error of about 2%.     

Kinetic spectrophotometric method for the determination of urinary cobalt based on its catalytic effect on the oxidation of -adrenaline hydrochloride by hydrogen peroxide

A catalytic for determination of nanomolar concentrations of Co(II), i.e., oxidation of -adrenaline hydrochloride with H₂O² in alkaline medium, is proposed. The reaction gives a low limit of detection of 2.5 × 10 ⁻⁹ M Co(II) in the reaction mixture, good reproducibility with a relative standard deviation (R.S.D.) of 4−5% in the Co(II) concentration range 8.0 × 10⁻⁹−8.0 × 10⁻⁸M and good selectivity. On the basis of this indicator reaction, a catalytic-spectrophotometric method for the determination of cobalt in small urine samples (5.00 ml) was elaborated. The analysis of 17 urine samples, taken from healthy persons of different ages, gave cobalt concentrations in the range 0.20–1.50 μmol 1⁻¹. The R.S.D. for ten replicate analyses of a urine sample with an average cobalt content of 0.63 μmol 1⁻¹ was 5.6%. The reliability of the method was verified by a comparative photometric method (r = 0.9755) and by a determination based on known additions of cobalt (r = 0.9894).     

A study on terbium sensitized chemiluminescence of ciprofloxacin and its application

A novel rapid flow injection method with chemiluminescence (CL) detection was established for the determination of ciprofloxacin (CPLX), which is an antibiotic commonly used. The method is based on CL of Ce(IV)–SO₃²⁻ sensitized by Tb³⁺–CPLX, and showed the intensive bands characteristic of Tb³⁺ (⁵D₄→⁷F₅). The optimum conditions for CL emission were investigated. The linear relationship between the relative CL intensity and the concentration of CPLX is in the range of 9.0×10⁻⁹–1.0×10⁻⁶ mol/l with a detection limit of 3.1×10⁻¹⁰ mol/l. The relative standard deviation is 2.8% (n=11) for a level of 5.0×10⁻⁸ mol/l. The method was applied to the analysis of CPLX in human serum and urine samples with satisfactory results. The possible mechanism for this sensitized CL reaction is also discussed.     

Non-extraction flow injection determination of cationic surfactants using eriochrome black-T

A new, rapid, sensitive, non-extraction batch, and flow injection spectrophotometric method for the determination of cationic surfactants (CSs) such as cetyltrimethyl ammonium bromide (CTAB), tetra-n-butyl ammonium chloride (TBAC) and cetylpyridinium chloride (CPC) is proposed. The method is based on the interaction of cationic surfactants with eriochrome black-T to form an ion-association complex. This complex has strong absorbance at 708 nm. The effects of chemical parameters and FIA variables on the determination of cationic surfactants were studied in detail, especially for CTAB. Under optimum conditions, the two linear calibration ranges of the method are 3.0 × 10⁻⁶ to 5.0 × 10⁻³ mol L⁻¹ CTAB, CPB and DTAB for the batch spectrophotometric method and 2.0 × 10⁻⁶ to 2.0 × 10⁻⁴ mol L⁻¹ CTAB, CPB and TBC for the flow injection spectrophotometric method. The sample throughput was 35 ± 5 samples h⁻¹ at room temperature. The relative standard deviations for 10 replicates of analysis of (2.0, 0.6 and 0.2) × 10⁻⁴ mol L⁻¹ CTAB were 1.2, 1.3, and 0.8%, respectively. In addition, the influence of potential interfering substances on the determination of cationic surfactants was studied. The proposed method is simple and rapid, using no toxic organic solvents. It was applied to the determination of trace CS in industrial wastewater with satisfactory results.     

毛细管电泳-安培法测定复方磺胺甲噁唑片中的有效成分

采用毛细管电泳-安培法(CE-AD)同时分离测定了磺胺甲噁唑(sulfamethoxazole,SMZ)、磺胺嘧啶(sulfadiazine,SD)和抗菌增效剂甲氧苄胺嘧啶(trimethoprim,TMP)3种常用磺胺类抗菌药物成分,考察了实验参数对分离、检测体系的影响。在优化实验条件下,以300μm碳圆盘电极作为工作电极,检测电位为1050mV(vs.SCE),在Na2B4O7(13mmol/L)-KH2PO4(18mmol/L)(pH5.8)的缓冲溶液中,分离电压18kV,进样6s,3组分在14min内可实现基线分离。上述3组分浓度分别在5×10-4~5×10-2、5×10-4~0.1和5×10-4~5×10-2g/L范围内与其峰电流强度呈线性关系,检出限达5.1×10-5~8.0×10-5g/L(S/N=3)。该方法已成功应用于复方磺胺甲噁唑片中抗菌活性成分的含量测定,结果令人满意。     

Indirect atomic absorption spectrometry (IAAS) as a tool for the determination of iodide in infant formulas by precipitation of AgI and redissolution with cyanide

A method to determine iodide in infant formula samples by indirect atomic absorption spectrometry (IAAS) was developed. The iodide in solution resulting from an alkaline digestion (Na₂CO₃–NaOH) of the sample is precipitated with silver; the precipitate is redissolved by adding cyanide solution, and this solution is subjected to GF-AAS. Temperatures of 1000 and 2100°C were selected for the ashing and atomization steps, respectively, using a mixture of Pd and Mg(NO₃)₂ as a matrix modifier (at concentrations of 36 and 16 μg ml⁻¹, respectively). The sensitivity, LOD, LOQ and characteristic mass obtained were, respectively, 1.12×10⁻² l μg⁻¹, 3.1 μg g⁻¹ and 10.4 μg g⁻¹ and 7.3 pg, referred to sample. The linear interval of concentrations extends up to 10 μg l⁻¹ of iodide, with no need to use the standard addition method; the mean R.S.D. of data within this range is 3.4%, with 2.9% over the whole procedure. No interfering effects were observed among the foreign ions studied, and 100.0% was the mean analytical recovery achieved within the linear range of concentrations. The application of the method to seven real samples gave a mean content of 12.8 μg g⁻¹ of iodide, as well as less than 3.1 μg g⁻¹ in eight other samples.     

Luminescent CuS nanotubes as silver ion probes

CuS nanotubes (NTs) made up of nanoparticles were successfully prepared in large quantities in an O/W microemulsion system under low temperature. Based on the characteristics of synchronous fluorescence spectroscopy (SFS), a new method with high sensitivity and selectivity was developed for rapid determination of silver ion with functional copper sulphide (CuS) nanotubes as a fluorescence probe. Under optimal conditions, functional copper sulphide displayed a calibration response for silver ion over a wide concentration range from 1.0 × 10⁻¹⁰ to 1.0 × 10⁻⁸ mol L⁻¹. The limit of detection was 0.5 × 10⁻¹⁰ mol L⁻¹ and the relative standard deviation of eight replicate measurements for the highest concentration (1 × 10⁻⁸ mol L⁻¹) was 3%. Compared with several fluorescence methods, the proposed method had a wider linear range and improved the sensitivity. Furthermore, the concentration dependence of the synchronous fluorescence intensity is effectively described by a Langmuir-type binding isotherm.     

A novel method for determination of peroxynitrite based on hemoglobin catalyzed reaction

A novel spectrofluorimetric method for the determination of peroxynitrite is proposed. The method is based on a mimetic enzyme catalyzed reaction with hemoglobin as the catalyst and l-tyrosine as the substrate. A new fluorescent substance is produced that might probably be the coupled dimmer of tyrosine, which, instead of nitryl-tyrosine, is likely to be a new marking substance of ONOO⁻ injury in vivo. Kinetics of the reaction is studied and the possible reaction mechanism is also recommended. The proposed method is simple and highly sensitive with a detection limit of 5.00 × 10⁻⁸ mol L⁻¹ of peroxynitrite. A liner calibration graph is obtained over the peroxynitrite concentration range 5.60 × 10⁻⁷ to 2.10 × 10⁻⁵ mol L⁻¹, with a correlation coefficient of 0.9983. Interferences from some amino acids and metal ions normally seen in biological samples, and also some anions structurally similar to ONOO⁻ are studied.     

Voltammetric determination of hypoxanthine based on the enhancement effect of mesoporous TiO2-modified electrode

A mesoporous TiO₂ was synthesized according to the reported method, and then used to modify the carbon paste electrode (CPE). The electrochemical behavior of hypoxanthine was investigated with great detail. Compared with the unmodified CPE, the mesoporous TiO₂-modified CPE greatly enhances the oxidation signal of hypoxanthine. Due to huge surface area, well-defined and special mesopores, the mesoporous TiO₂-modified CPE shows considerable enhancement effect toward hypoxanthine. Based on this, a sensitive, rapid and convenient electrochemical method was developed for the determination of hypoxanthine. The linear range is over the range from 2.0 × 10⁻⁷ to 5.0 × 10⁻⁵ mol L⁻¹, and the limit of detection is estimated to be 5.0 × 10⁻⁸ mol L⁻¹. The relative standard deviation (RSD) for 10 mesoporous TiO₂-modified CPEs is 5.7%. Finally, this sensing method was successfully used to determine hypoxanthine in human blood serum samples.     

Spectrofluorimetric Assay of Cationic Surfactants by Fluorescence Quenching of 9-Anthracenecarboxylic Acid

A new simple, selective and sensitive fluorescence quenching method was developed to determine cationic surfactants with the 9-anthracenecarboxylic acid (ACA). The fluorescence intensity of ACA was decreased by addition of trace amounts of cationic surfactants. Under optimum conditions, the ratio of fluorescence intensity in the absence and presence of cationic surfactants was proportional to the concentration of cationic surfactants over the range of 0.3–4.5 × 10⁻⁵ mol L⁻¹ for cetylpyridinium chloride (CPC) and 0.4–6.0 × 10⁻⁵ mol L⁻¹ for cetyl trimethyl-ammonium bromide (CTAB). The detection limits are 1.0 × 10⁻⁶ mol L⁻¹ for CPC and 1.2 × 10⁻⁶ mol L⁻¹ for CTAB, respectively. Based on this approach, this paper presents a new quantitative method for cationic surfactants assay.     

An investigation of the chemiluminescence reaction in the sodium hypochlorite–folic acid–emicarbazide hydrochloride system

A chemiluminescence method for the determination of folic acid by the sodium hypochlorite–folic acid–semicarbazide hydrochloride system with a new flow injection technique has been established. The new method can perform simple, sensitive and rapid determinations of folic acid. The response to the concentration of folic acid, in the range of 1.0×10⁻⁷5.0×10⁻⁵ g/ml, is linear. The relative standard deviation of the method is 2.3% (C_s=4.0×10⁻⁶ g/ml, n=11). The detection limit is 2.7×10⁻⁸ g/ml. This method is suitable for automatic and continuous analysis, and has been successfully tested for the determination of folic acid in a folic acid tablet.     

Potentiometric Membrane Sensor for Determination of Saccharin

A potentiometric poly(vinyl chloride) membrane sensor for determination of saccharin is described. It is based on the use of Aliquat 336S-saccharinateion-pair as an electroactive material in plasticized PVC membranes with o-nitrophenyloctylether or dioctylphthalate. The sensor is conditioned for at least two days in 0.1 mol L⁻¹ sodium saccharinate before use. It exhibits fast, stable and Nernstian response for saccharinate ions over the concentration range of 1.0 × 10⁻¹–5.0 × 10⁻⁵ mol L⁻¹ and pH range of 4.5–11. The sensor is used for determination of saccharin in some dosage forms. Results with an average recovery of 101% and a mean standard deviation of 0.2% are obtained which is compared favourably with data obtained using the British pharmacopoeia method. The sensor shows reasonable selectivity towards saccharin in presence of many anions and natural sweeteners.     

Kinetic Determination of Mercury(II) at Trace Level from Its Catalytic Effect on a Ligand Substitution Process

A catalytic kinetic method (CKM) is presented for the determination of mercury(II) based on its catalytic effect on the rate of substitution of N-methylpyrazinium ion (Mpz⁺) onto hexacyanoferrate(II). The progress of the reaction was monitored spectrophotometrically at 655 nm by registering the increase in absorbance of the product [Fe(CN)₅(Mpz]²⁻ under the reaction conditions: 5 × 10⁻³ mol L⁻¹ [Fe(CN)₆]⁴⁻), 5 × 10⁻⁵ mol L⁻¹ [Mpz⁺], T = 25.0 ± 0.1°C, pH 5.00 ± 0.02 and ionic strength, I = 0.1 mol L⁻¹ (KNO₃). Quantitative rate data at specified experimental conditions showed a linear dependence of the absorbance after fixed time A _t on the concentration of mercury(II) catalyst in the range 20.06–702.1 ng mL⁻¹. The maximum relative standard deviations and percentage errors for the determination of mercury(II) in the range of 20.06–200.6 ng mL⁻¹ were calculated to be 1.7 and 2.7% respectively. The detection limit was found to be 7.2 ng mL⁻¹ of mercury(II). Accuracy (expressed in terms of recoveries) was in the range of 98–103%. Figures of merit and interference due to many cations and anions was investigated and discussed. The applicability of the method was demonstrated by determining the mercury(II) in different synthetic samples and confirming the results using atomic absorption spectrophotometry. The proposed method allowed determination of mercury(II) in the range 20.06–702.1 ng mL⁻¹ with very good selectivity and an output of 30 samples h⁻¹.__________From Zhurnal Analiticheskoi Khimii, Vol. 60, No. 6, 2005, pp. 654–661.Original English Text Copyright © 2005 by Surendra Prasad.This article was submitted by the author in English.     

Fluorescence enhancement effect for the determination of DNA with calcein-cetyl trimethyl ammonium bromide system

A new spectrofluorimetric method was developed for the determination of trace amounts of DNA using the calcein as a fluorescent probe. In the presence of appropriate amounts of the cationic surfactant cetyl trimethyl ammonium bromide (CTAB), the anionic dye calcein dimerizes. The weak fluorescence intensity of the dimer was enhanced by adding DNA at pH 6–7. The interaction between calcein–CTAB and DNA was studied on the basis of this behavior and a new method was developed for determining DNA. Under the optimal conditions, the enhanced fluorescence intensity was in proportion to the concentration of DNA in the range of 4.0 × 10⁻⁶ to 8.0 × 10⁻⁵ g L⁻¹ for fsDNA and thermally denatured ctDNA (4.5 × 10⁻⁶ to 9.0 × 10⁻⁵ g L⁻¹). The detection limits (S/N = 3) were 2.0 × 10⁻⁶ and 2.2 × 10⁻⁶ g L⁻¹, respectively. This method was used for determining the concentration of DNA in synthetic samples with satisfactory results.     

Spectrophotometric determination of cobalt as the orange cobalt-biacetylmonoxime 2-pyridylhydrazone complex

A spectrophotometric method for the determination of cobalt is described. The method is based on the formation of an orange color by reaction of cobalt(II) with biacetylmonoxime 2-pyridylhydrazone in basic solutions. The molar absorptivity at 480 nm is about 9.2 × 10³ liters mol⁻¹ cm⁻¹ (pH 10) and spectrophotometric sensitivity is 0.0062 μg Co cm⁻² for ABSORBANCE = 0.001.     

Adsorption stripping voltammetry of phenol at Nafion-modified glassy carbon electrode in the presence of surfactants

In this paper, a new voltammetric method for the determination of phenol is described. In pH 8.00 phosphate buffer and in the presence of long-chain cationic surfactant—cetyltrimethylammonium bromide—phenol has a very sensitive oxidation peak at 0.47 V (vs. SCE) on the Nafion-modified glassy carbon electrode (GCE). The experimental parameters, such as supporting electrolyte and pH values, amounts of Nafion, varieties and concentration of surfactants, accumulation potential and time, as well as scan rate were optimized. The peak current is linear with the concentration of phenol in the range from 8×10⁻⁹ to 1×10⁻⁵ M, and the detection limit is 1×10⁻⁹ M after being accumulated at −0.50 V (vs. SCE) for 3 min. Trace levels of phenol in water samples were determined by using this voltammetric method, the average recovery was calculated to be 99.56%.     

Spectrophotometric determination of trace amounts of acetylacetone in aqueous solutions

A sensitive spectrophotometric method for the determination of trace amounts of acetylacetone in aqueous solution is carried out. In the presence of bicarbonate solution, diazotized anthranilic acid reagent reacts rapidly with acetylacetone to form a yellow-colored compound with maximum absorption at 330 nm, which is water-soluble and reasonably stable. Adherence to Beer's law is observed in the range 20–200 μg of acetylacetone/25 ml, with a molar absorptivity of 19.5 × 10³ liters mol⁻¹ cm⁻¹, a sensitivity index of 0.0051 μg cm⁻², relative to + 0.3 to −0.9%, and a relative standard deviation of 0.5–1.4%, depending on the concentration level.     

Photometric determination of iron (III)

A sensitive colored reaction of tiron with iron (III) is described. It is based on a complex formation between tiron and iron (III) in basic medium. The method is suitable to determine 0.4–10 ppm of iron (III) with a relative standard deviation of 0.45–1.4% depending on the concentration level, molar absorptivity of 5.7 × 10³ liter mol⁻¹ cm⁻¹, and Sandell sensitivity index of 0.0098 μg/cm².Because of being simple and rapid, this method can certainly be used in routine analysis.